Panasonic Hdc Sd5 Operating Instructions

							21VQT1H62
Before using
Rotate the lens hood 
counter-clockwise A to remove it. In 
order to attach it, place into slot B, 
and then rotate it clockwise C.
≥When fitting the tele conversion lens 
(VW-T3714H; optional) or the wide conversion 
lens (VW-W3707H; optional), first remove the 
lens hood.
(Refer to the operating instructions for the tele 
conversion lens or the wide conversion lens.)
The tripod receptacle is a hole used to mount a 
tripod for the unit. Use of Panasonic’s VW-CT45 
(optional) standard tripod is recommended. (For 
details on mounting the tripod, refer to the 
operating instructions for the tripod.)
ACamera base
BScrew for mounting the unit
CTripod pin
≥You can perform operations easily using the 
remote control when the tripod is used. (l22)
≥The SD card/battery cover cannot be opened 
when the tripod is used. Insert an SD card and 
the battery before attaching this unit to the 
tripod. (l27, 33)
Using the LCD monitor
You can record the image while viewing it on the 
LCD monitor.
1Press the LCD OPEN button and 
then open the LCD monitor.
≥It can open up to 90o.
≥Place this unit level and then press the 
LCD OPEN button. Depending on the angle of 
this unit, the LCD monitor may not open 
automatically. In this case, open it with your 
hand.
Angles at which the LCD monitor will open 
and not open automatically
AAngle at which it will not open
BAngle at which it will open
CApprox. 15o
DApprox. 40o
Lens hood
Tripod receptacle
A
C
B
AC
B
LCD
OPEN
A
BB
A
BB C
D
VQT1H62_ENG_PP.book  21 ページ  ２００７年７月１７日　火曜日　午後５時４４分 
						

							22VQT1H62
Before using
2Adjust the angle of the LCD 
monitor as desired.
≥It can be rotated 180° towards the lens A and 
90° towards the opposite direction B.
≥The brightness and color level of the LCD 
monitor can be adjusted. (l40)
≥The unit may be damaged or fail if the LCD 
monitor is forcibly opened or rotated.
≥Check that the terminal cover is closed before 
closing the LCD monitor.
≥Close the LCD monitor properly.
Using the remote control
1 Photoshot button [ ]*
2 On-screen display button [EXT DISPLAY] 
(l76)
3 Date/time button [DATE/TIME] (l39)
4 Playback operation buttons (l65, 66)
5 Delete button [ ]
*
6 Direction buttons [3,4,2,1] (l38)
7 Recording start/stop button [START/
STOP]
*
8 Zoom/volume buttons [ZOOM, VOL]*
9 Menu button [MENU]* (l38)
10 Enter button [ENTER] (l38)
* means that these buttons function in the same 
manner as the corresponding buttons on the 
unit.
A
B
ZOOM START/
STOP PHOTO
SHOT EXT
DISPLAY
DATE/
TIME
VOL
PLAY
STOP SKIP SKIP
MENU
ENTER
PA U S E
SEARCH
STILL ADV STILL ADVSEARCH
1
2
3
4
67
8
9
1
0
5
VQT1H62_ENG_PP.book  22 ページ  ２００７年７月１７日　火曜日　午後５時４４分 
						

							23VQT1H62
Before using
ªInstall a button-type battery
Install the supplied button-type battery in the 
remote control before using it.
1While pressing the stopper A, 
pull out the battery holder.
2Set the button-type battery with 
its (i) mark facing upward and 
then put the battery holder back 
in place.
Concerning the button-type battery
≥When the button-type battery runs down, 
replace it with a new battery (part number: 
CR2025). The battery should normally last 
about 1 year, however this depends on how 
frequently the unit is used.
≥Keep the button-type battery out of the reach of 
children to prevent swallowing.
ªRemote control usable range
The distance between the remote control and the 
unit’s remote control sensor A: Within approx. 
5m (16feet)
Angle: Approx. 10o up and 15o down, left, and 
right
≥The remote control is intended for indoor 
operation. Outdoors or under strong light, the 
unit may not operate properly even within the 
usable ranges.
CAUTION
Danger of explosion if battery is incorrectly 
replaced. Replace only with the same or 
equivalent type recommended by the 
manufacturer. Dispose of used batteries 
according to the manufacturer’s instructions.
Replace battery with Panasonic PART NO. 
CR2025 only. Use of another battery may 
present a risk of fire or explosion.
Caution: Battery may explode if mistreated.
Dispose of used battery promptly. Keep away 
from children.
Do not recharge, disassemble or dispose of in 
fire.
A
A
VQT1H62_ENG_PP.book  23 ページ  ２００７年７月１７日　火曜日　午後５時４４分 
						

							Before using
24VQT1H62
Cards that you can use with this unit
* The recording may suddenly stop during motion picture recording depending on the SD card you use. 
(l44)
ªHandling precautions
≥Do not expose the terminals of the card to water, debris, dirt or dust.
≥Do not place in the following areas:
jIn direct sunlight.
jIn very dusty or humid areas.
jNear a heater.
jLocations susceptible to significant difference in temperature (condensation can occur).
jWhere static electricity or electromagnetic waves occur.
≥To protect cards, return them to their bags or cases when you are not using them.
Card typeSD Memory CardSDHC Memory 
Card
Capacity8MB, 16MB32 MB, 64 MB, 
128 MB256 MB, 512 MB, 
1GB, 2GB4GB, 8GB
Motion picture 
recordingCannot be 
used.Cannot be 
guaranteed in 
operation.
*
Refer to “About SD cards that you can use 
for motion picture recording”.
Still picture 
recordingCan be used.
This unit (an SDHC compatible device) is compatible with both SD Memory Cards and SDHC 
Memory Cards. You can use SDHC Memory Cards on devices that are compatible with them. 
However, you cannot use SDHC Memory Cards on devices that are only compatible with SD 
Memory Cards. (When using an SDHC Memory Card on another device, always read the operating 
instructions of that device.)
VQT1H62_ENG_PP.book  24 ページ  ２００７年７月１７日　火曜日　午後５時４４分 
						

							Before using
25VQT1H62
ªAbout SD cards that you can use for motion picture recording
We recommend using SD Memory cards and SDHC Memory cards conforming to Class 2 or higher of 
the SD Speed Class Rating or the following SD cards made by Panasonic for motion picture recording.
*1 No longer made.
*2 Available from Sep. 2007
≥Operation in motion picture recording is not guaranteed with an SD card memory from 32 MB to 8 GB 
except the cards above. (The recording may suddenly stop during motion picture recording.)
≥For the purposes of these operating instructions, SD Memory Card and SDHC Memory Card are 
referred to as the “SD card”.
≥This unit supports SD Memory Cards formatted in FAT12 system and FAT16 system based on SD 
Memory Card Specifications and SDHC Memory Cards formatted in FAT32 system.
≥If you wish to use Memory Cards that are 4 GB and 8 GB, only SDHC Memory Cards can be used.
≥4 GB (or more) Memory Cards that do not have the SDHC logo are not based on SD Memory Card 
Specifications.
≥Use this unit to format SD cards. If an SD card is formatted on other products (such as a computer), 
the time spent for recording may become longer and you may not be able to use the SD card. (l75) 
(Do not format it on a PC etc.)
≥When the write-protect switch A on SD card is locked, no recording, deletion or 
editing will be possible on the card.
≥Keep the Memory Card out of reach of children to prevent swallowing.
≥A MultiMediaCard cannot be used on this unit.
Card typePro High Speed
SD Memory CardSuper High 
Speed
SD Memory CardHigh Speed
SD Memory CardSDHC Memory 
Card
256 MB— RP-SDH256*1RP-SDR256 —
512 MBRP-SDK512*1RP-SDH512*1RP-SDR512 —
1GBRP-SDK01G*1
RP-SDV01GRP-SDH01G*1RP-SDQ01G*1
RP-SDR01G—
2GBRP-SDK02G*1
RP-SDV02G—RP-SDQ02G
*1
RP-SDR02G*1
RP-SDM02G—
4GB———RP-SDM04G
RP-SDR04G*1
RP-SDV04G
8GB— — — RP-SDV08G*2
4
A
VQT1H62_ENG_PP.book  25 ページ  ２００７年７月１７日　火曜日　午後５時４４分 
						

							26VQT1H62
Setup
Setup
Charging the battery
When this unit is purchased, the battery is not 
charged. Charge the battery before using this 
unit.
≥Connect the battery to an AC adaptor to 
recharge it.
≥Refer to page 28 concerning batteries that 
can be used with this unit.
1Connect the AC cable to the AC 
adaptor and the AC outlet.
≥Remove the DC cable beforehand.
2Put the battery on the battery 
mount by aligning the mark, and 
then securely plug it in.
≥The output plug of the AC cable is not 
completely connected to the AC adaptor jack. 
As shown in A, there is a gap.
ªCharging lamp
Lights up:
Charging
Goes off:
Charging completed
Flashing:
Make sure that the terminals of the battery or the 
AC adaptor are not exposed to dirt, foreign 
objects or dust, then reconnect them properly.
Disconnect the AC cable from the AC outlet 
when you remove dirt, foreign objects or dust on 
the terminals of the battery or the AC adaptor.If the charging lamp is still flashing, something 
may be wrong with the battery or AC adaptor. 
Contact your dealer.
≥Battery charging time (l28)
≥We recommend using Panasonic batteries 
(l10, 28, 132).
≥If you use other batteries, we cannot guarantee 
the performance/quality of this product.
If the DC cable is connected to the AC 
adaptor, then the battery will not charge. 
Remove the DC cable from the AC adaptor.
A
VQT1H62_ENG_PP.book  26 ページ  ２００７年７月１７日　火曜日　午後５時４４分 
						

							27VQT1H62
Setup
Inserting/removing the battery
1
While sliding the SD CARD/
BATTERY OPEN lever A, move 
the SD card/battery cover and 
open it.
2Insert the battery until it clicks 
while paying attention to the 
direction of the battery.
BPush the center of the battery until it locks.
3Close the SD card/battery cover.
≥Securely close it until it clicks.
1Open the SD card/battery cover.
2Remove the battery.
≥Move A in the direction of the arrow to unlock 
it and then remove the battery.
3Close the SD card/battery cover.
≥Be sure to set the mode dial to OFF and check 
that the status indicator is off before removing 
the battery.
≥The SD card/battery cover opens up to 180o.
Inserting the battery
A
1
2
B
Removing the battery
CAUTION
Danger of explosion if battery is incorrectly 
replaced. Replace only with the same or 
equivalent type recommended by the 
manufacturer. Dispose of used batteries 
according to the manufacturer’s instructions.
A
VQT1H62_ENG_PP.book  27 ページ  ２００７年７月１７日　火曜日　午後５時４４分 
						

							Setup
28VQT1H62
Charging and recording time
ªAbout batteries that you can use for this unit
The Panasonic battery that can be used with this unit is VW-VBG130/VW-VBG260/VW-VBG6.
VW-VBG130/VW-VBG260/VW-VBG6 come with a function to check whether the battery and unit can 
be safely used together.
≥The battery pack holder kit VW-VH04 (optional) is necessary if using VW-VBG260/VW-VBG6.
≥Batteries made by other companies which have been certified by Panasonic may be used with this 
unit, but we offer no guarantee as to the quality, performance or safety of such batteries.
≥In order to safely use the unit, we recommend that you use genuine Panasonic batteries which have 
been tested by our quality control process.
≥We cannot accept any liability whatsoever for damages to the unit or accidents caused by 
non-genuine Panasonic batteries (including those that have been certified by Panasonic).
≥Exercise care when purchasing batteries. Many fake or imitation batteries have been found among 
those sold at unusually low prices and those which customers cannot check for themselves before 
purchasing.
ªCharging time
The times shown in the tables below are for when the temperature is 25oC (77oF) and the humidity is 
60%. If the temperature is higher or lower than 25oC (77oF), the charging time will become longer.
≥The charging times shown in the table are approximations.
≥“2 h 20 min” indicates 2 hours 20 minutes.
≥When you charge a battery that has not been used for long time, the charging time will become 
longer.
ªRecordable time
≥The times shown in the table below are for when the temperature is 25oC (77oF) and the humidity is 
60%. These times are approximations.
≥The actual recordable time refers to the recordable time on a card when repeatedly starting/stopping 
recording, turning the unit on/off, moving the zoom lever etc.
≥The recordable times shown in the table are approximations.
≥“1 h 25 min” indicates 1 hour 25 minutes.
Battery model numberVoltage/capacityCharging time
Supplied battery/
VW-VBG130 (optional)7.2 V/1320 mAh 2 h 20 min
VW-VBG260 (optional) 7.2 V/2640 mAh 4 h
VW-VBG6 (optional) 7.2 V/5800 mAh 8 h 50 min
Battery model numberVoltage/
capacityMaximum continuously 
recordable timeActual recordable 
time
Supplied battery/
VW-VBG130 (optional)7.2 V/1320 mAh 1 h 25 min 55 min
VW-VBG260 (optional) 7.2 V/2640 mAh 2 h 40 min 1 h 40 min
VW-VBG6 (optional) 7.2 V/5800 mAh 6 h 40 min 4 h 10 min
VQT1H62_ENG_PP.book  28 ページ  ２００７年７月１７日　火曜日　午後５時４４分 
						

							Setup
29VQT1H62
≥The recordable times will vary depending on the status of use. These times are approximations.
≥The recordable time will become shorter in the following case:
jWhen you use this unit with the LCD monitor lit up by pressing the POWER LCD EXTRA button.
≥The batteries heat up after use or charging. This unit will also heat up while being used. This is not a 
malfunction.
≥Be aware that the operating time of the battery will become shorter in low temperatures. We 
recommend charging a spare battery for use when recording.
ªAbout the remaining battery capacity indication
The remaining battery capacity is displayed in minutes when using the 
Panasonic battery that you can use for this unit. It may take time to display 
the remaining battery capacity.
≥The display changes as the battery capacity reduces. ####.
If there is less than 3 minutes remaining, then   will become red. If the battery discharges, then 
( ) will flash.
≥The remaining battery capacity may not be displayed correctly where the temperature is low or high 
or if the battery was not used for a long period of time.
To correctly display the remaining battery capacity, recharge the battery, discharge it and then charge 
it again. (Even if this operation is performed, it may not be possible to display the remaining battery 
capacity correctly if the battery was used for a long period of time where the temperature is low or 
high or if the battery was repeatedly charged.)
≥The maximum amount of remaining battery capacity able to be indicated is 999 minutes. If the actual 
remaining time exceeds 999 minutes, the indication will stay green and will not change until the 
remaining time falls below 999 minutes.
≥The time displayed is an approximation of the remaining time your battery will provide useful power. 
The actual time can vary depending on your actual use.
≥When turning the mode dial to switch modes, the time indication will turn off in order to recalculate the 
remaining battery capacity time.
≥When using the AC adaptor or batteries made by other companies, the remaining battery capacity will 
not be shown.
60min
VQT1H62_ENG_PP.book  29 ページ  ２００７年７月１７日　火曜日　午後５時４４分 
						

							30VQT1H62
Setup
Connecting to the AC outlet
1
Connect the AC cable to the AC 
adaptor and the AC outlet.
2Connect the DC cable to the AC 
adaptor.
3While sliding the SD CARD/
BATTERY OPEN lever A, move 
the SD card/battery cover and 
open it.
4Open the battery cable cover.
5Attach the DC cable.
BPush the center until it locks.
6Close the SD card/battery cover.
≥Securely close it until it clicks.
≥Pass the DC cable through the SD card/battery 
cover as shown in the illustration.
≥Do not use the AC cable with any other 
equipment as it is designed only for this unit. 
Do not use the AC cable from other equipment 
with this unit.
ªAbout the battery pack holder kit 
(VW-VH04; optional)
If using the battery pack holder kit, open the 
battery cable cover on this unit and then pass the 
DC cable for the battery pack holder kit through 
the SD card/battery cover.
≥Read the operating instructions of the battery 
pack holder kit for details on how to use it.
≥If you are not attaching the DC cable for use, 
close the battery cable cover.
≥While the DC cable is connected to the AC 
adaptor, the battery will not charge.
A
1
2
B
VQT1H62_ENG_PP.book  30 ページ  ２００７年７月１７日　火曜日　午後５時４４分