Panasonic Hd-plc Ethernet Adaptor Bl-pa100a Operating Instructions

							11[For assistance, please call: 1-800-272-7033]
Useful Information
Understanding the indicators
PLCBlue, lit The adaptor is successfully connected to the 
HD-PLC network.
Blue, flashing The terminal is being registered to the master.
Blue, flashes 
once every 5 or 
10 secondsThe adaptor is registered to the master, but it is 
not connected to the HD-PLC network.
Blue, turns off 
once every 10 
secondsThe master has detected another master 
adaptor. In this situation, performance will be 
affected by the presence of the other master 
adaptor.
Red, lit for 5 
secondsThere was an error during registration. Try again.
Red, lit The adaptor is not functioning properly and 
cannot communicate over the HD-PLC network. 
Contact an authorized Panasonic service center.
Off The adaptor is not plugged in.
The adaptor is not connected to the HD-PLC 
network (no other adaptors found, not configured, 
etc.).
LANGreen, lit A LAN cable is connected to the adaptor.
Green, flashing Data is being sent/received.
Orange, lit There is no network device connected to the 
adaptor via the LAN cable, or the network device 
is not turned on.
Off The adaptor is not plugged in.
MASTERGreen, lit The adaptor is configured as the master.
Green, flashes 
for 10 secondsA terminal has been successfully registered to 
the master.
Off The adaptor is not configured as the master.
BL-PA100A_OI.book  Page 11  Thursday, March 16, 2006  4:14 PM 
						

							12
Useful Information
Resetting an adaptor
Normally an adaptor does not need to be reset, however, you may need to reset an 
adaptor if:
 You are concerned that another adaptor may have been accidentally 
registered to your master. (For example, the adaptor of someone who lives 
in the same apartment building as you.)
 An error occurs while registering a terminal to the master.
 You are registering an adaptor
Note
 Resetting a terminal erases its registration to the master. It must be registered 
to the master again in order to be used.
 If the master is reset, all terminals must be registered to the master again in 
order to be used.
Follow the procedure below to reset an adaptor.
1.Press the FACTORY DEFAULT RESET button on the adaptor for about 3 
seconds.
 The adaptor’s indicators will begin flashing.
2.Once the adaptor’s indicators stop flashing, the adaptor has been reset.
 Do not disconnect or unplug the AC cord for 30 seconds.
BL-PA100A_OI.book  Page 12  Thursday, March 16, 2006  4:14 PM 
						

							13[For assistance, please call: 1-800-272-7033]
Useful Information
Troubleshooting
Performance issues
The troubleshooting notes in this section are provided to resolve the following types 
of performance issues.
 Inability to transmit data over the HD-PLC network
 Slow data transmission speeds (interrupted video or audio, slow download 
speeds, etc.)
 Intermittent or varied performance (faster at certain times, slower at others)
 Interference caused by an adaptor
The PLC indicator is not lit in blue even though you have registered the 
adaptor.
Troubleshooting notes
In most cases, performance issues such as those listed above can be resolved by 
performing the following troubleshooting notes. Each note contains several steps. 
After you perform each step, test the terminal’s network speed (see page 10) to 
see if the issue has been resolved. For more information, access the Panasonic 
PLC Support Site at: http://panasonic.co.jp/pcc/products/en/plc/
Troubleshooting note #1:
Adaptor issues
Perform each step until the performance issue is solved. 
1.Confirm that the AC cords of both the master and terminal adaptor are 
connected to the wall outlet. If an adaptor’s LAN indicator is not lit, the adaptor 
is not receiving power.
2.Confirm that all LAN cables are securely connected to each adaptor. Use 
quality LAN cables. Also confirm that other network devices (routers, hubs, 
etc.) are turned on as well as properly connected and configured.
3.Disconnect the AC cord from the master and/or terminal adaptor, then 
connect it again to restart the adaptor.
4.Try connecting the master and/or terminal adaptor to a different wall outlet.
5.If you are not able to connect an adaptor’s AC cord directly to a wall outlet and 
must use a power strip, make sure the power strip is plugged directly into a 
wall outlet and not to another power strip.
6.Make sure the power strip does not have a noise filter or a surge protector, as 
these features may interfere with the performance of your adaptors.
7.Use a power strip with an AC cord that is as short as possible.
8.Re-register the terminal following the procedure on page 7.
If you are still experiencing performance issues, continue to the next 
troubleshooting note.
BL-PA100A_OI.book  Page 13  Thursday, March 16, 2006  4:14 PM 
						

							14
Useful Information
Troubleshooting note #2:
Eliminating interference caused by other appliances
Perform each step until the performance issue is solved.
1.Identify potential electrical noise emitting appliances, and unplug them (if 
possible) briefly while you test the adaptor’s network speed.
The following appliances are more likely to produce noise:
 Battery chargers (including cell phone chargers)
 Hair dryers
 Vacuum cleaners
 Lights or lamps which have a dimmer switch or a touch-sensitive on/off 
feature
 Power drills
2.If unplugging a device seems to resolve the adaptor’s performance issue, 
connect the device to a different wall outlet. 
3.If connecting the device to a different wall outlet does not resolve the 
performance issue, connect the device to a noise filtering power strip with an 
AC cord that is at least 3 m (about 10 ft.) long.
Troubleshooting note #3:
Eliminating interference caused by an adaptor
This product may interfere with the following appliances:
 Short wave radios
 Lights or lamps which have a touch-sensitive on/off feature
 Other PLC adaptors which do not use the HD-PLC standard
Perform each step until the performance issue is solved. If the following steps do 
not resolve the issue, refer to the Panasonic PLC Support Site at: 
http://panasonic.co.jp/pcc/products/en/plc/ or call our customer call center at 
1-800-272-7033.
1.Make sure that the appliance is not plugged into the same wall outlet as an 
adaptor.
2.Move the appliance away from any nearby adaptors.
3.Connect the appliance to a power strip.
4.For short wave radios, place the radio near a window. 
BL-PA100A_OI.book  Page 14  Thursday, March 16, 2006  4:14 PM 
						

							15[For assistance, please call: 1-800-272-7033]
Useful Information
Specifications
All specifications are subject to change without notice.
Power Line Communication interface
LAN interface
User interface
Standard HD-PLC
Actual transmission 
speed
*1
*1 Results may vary depending on electrical conditions, network environment, and other 
factors. For information on how transmission speed is measured, access the Panasonic 
PLC Support Site at: http://panasonic.co.jp/pcc/products/en/plc/
UDP: Max. 70 Mbps
TCP
*2: Max. 42 Mbps
*2 Using Linux FTP.
Maximum recommended 
no. of adaptors per 
network
*3
*3 Performance may be affected as more adaptors are added to the network.
16 (including the master)
Maximum recommended 
no. of network devices 
connected to an adaptor
*4
*4 Connecting more network devices to an adaptor may increase network traffic and affect 
performance.
8
Standard IEEE 802.3/IEEE 802.3u
Interface 10 Base-T
100 Base-TX
Auto MDI/MDI-X
Protocol IPv4, IPv6, TCP, UDP
Access method CSMA/CD
IndicatorsPLC (blue, red)
LAN (green, orange)
MASTER (green)
Other Mode Selector (MASTER or TERMINAL switch)
SETUP button
FACTORY DEFAULT RESET button
BL-PA100A_OI.book  Page 15  Thursday, March 16, 2006  4:14 PM 
						

							16
Useful Information
General
HD-PLC interface
Operational environment 0–40 °C (32–104 °F)
20%–85% humidity (without condensation)
Dimensions (W x D x H) Approx. 121 mm x 40 mm x 70 mm
(4 3/4” x 1 9/16” x 2 3/4”)
Weight 240 g (0.53 lb.)
Power supply Input 120 V, 60 Hz
Power consumption 4 W
Frequency band 4–28 MHz
Modulation Wavelet OFDM (16 PAM–2 PAM)
Transmission PHY rate
Max. 190 Mbps
*1
*1 This is the theoretical maximum data transmission speed of the HD-PLC standard.
Access method CSMA/CA
TDMA
Error correction Reed-Solomon encoder/decoder
Convolutional encoder/Viterbi decoder
Encryption AES 128-bit encryption
Communication distance
Approx. 150 m (490 ft.)
*2
*2 Varies depending on the electrical environment. For more information, see page 4.
BL-PA100A_OI.book  Page 16  Thursday, March 16, 2006  4:14 PM 
						

							17[For assistance, please call: 1-800-272-7033]
Useful Information
FCC and other information
This equipment has been tested and found to comply with the limit for a Class B 
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses, and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television, reception, which 
can be determined by tuning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Any changes or modifications not expressly approved by the party responsible for 
compliance could void the users authority to operate this device.
NOTICE
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions:
1.This device may not cause harmful interference.
2.This device must accept any interference received, including interference that 
may cause undesired operation.
Responsible Party
Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094
Phone number: 1-800-211-PANA (7262)
Environment
Do not place the unit in a room where the temperature is less than 0° C (32° F) or 
greater than 40° C (104° F). Allow 10 cm (4 in.) clearance around the unit for proper 
ventilation. Avoid excessive smoke, dust, mechanical vibration, shock, or direct 
sunlight.
Routine Care
Wipe the unit with a soft cloth. Do not use benzine, thinner, or any abrasive powder. 
When you leave the unit unused for a long period of time, unplug the AC cord from 
the outlet.
In the Event of Trouble
Consult an authorized Panasonic Factory Service Center.
BL-PA100A_OI.book  Page 17  Thursday, March 16, 2006  4:14 PM 
						

							18
Useful Information
Copyright information
Panasonic cannot accept inquiries 
regarding the content of the following 
copyright and license information.
______________________________________________
LICENSE ISSUES
This product uses some parts of thttpd-2.25b, OpenSSL, 
SSL and newlib.
The use of parts described above are based on the license 
below. 

============================================
Copyright1995 by Jef Poskanzer .All 
rights reserved.
Redistribution and use in source and binary forms, with or 
without modification, are permitted provided that the 
following conditions
are met:
1. Redistributions of source code must retain the above 
copyright notice, this list of conditions and the following 
disclaimer.
2. Redistributions in binary form must reproduce the above 
copyright notice, this list of conditions and the following 
disclaimer in the documentation and/or other materials 
provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND 
CONTRIBUTORS AS IS AND ANY EXPRESS OR 
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY 
AND FITNESS FOR A PARTICULAR PURPOSE ARE 
DISCLAIMED.IN NO EVENT SHALL THE AUTHOR OR 
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, 
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT 
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR 
BUSINESS INTERRUPTION) HOWEVER CAUSED AND 
ON ANY THEORY OF LIABILITY, WHETHER IN 
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING 
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 
OUT OF THE USE OF THIS SOFTWARE, EVEN IF 
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
============================================
Some parts of the thttpd-2.25b are provided with the 
following copyright notices with license noted above.
Copyright1995,1998,1999,2000 by Jef Poskanzer 
. All rights reserved.
Copyright1995,1998,1999,2000,2001 by Jef Poskanzer 
. All rights reserved.
Copyright1995,1998,2000 by Jef Poskanzer 
. All rights reserved.Copyright1995,2000 by Jef Poskanzer 
. All rights reserved.
Copyright1996 by Jef Poskanzer . All 
rights reserved.
Copyright1998 by Jef Poskanzer . All 
rights reserved.
Copyright1998,2001 by Jef Poskanzer 
. All rights reserved.
Copyright1999 by Jef Poskanzer . All 
rights reserved.
Copyright1999,2000 by Jef Poskanzer 
. All rights reserved.
Some parts of the thttpd-2.25b are provided with the 
following copyright notices and license.
============================================
Copyright (c) 1988 Regents of the University of 
California.All rights reserved.
Redistribution and use in source and binary forms are 
permitted provided that the above copyright notice and this 
paragraph are duplicated in all such forms and that any 
documentation, advertising materials, and other materials 
related to such distribution and use acknowledge that the 
software was developed by the University of California, 
Berkeley.The name of the University may not be used to 
endorse or promote products derived from this software 
without specific prior written permission. THIS SOFTWARE 
IS PROVIDED AS IS AND WITHOUT ANY EXPRESS OR 
IMPLIED WARRANTIES, INCLUDING, WITHOUT 
LIMITATION, THE IMPLIED WARRANTIES OF 
MERCHANTIBILITY AND FITNESS FOR A PARTICULAR 
PURPOSE.
============================================

============================================
Copyright (c) 1998-2002 The OpenSSL Project.All rights 
reserved.
Redistribution and use in source and binary forms, with or 
without modification, are permitted provided that the 
following conditions are met:
1. Redistributions of source code must retain the above 
copyright notice, this list of conditions and the following 
disclaimer. 
2. Redistributions in binary form must reproduce the above 
copyright notice, this list of conditions and the following 
disclaimer in the documentation and/or other materials 
provided with the distribution.
3. All adver tising materials mentioning features or use of 
this software must display the following acknowledgment: 
This product includes software developed by the OpenSSL 
Project for use in the OpenSSL Toolkit. 
(http://www.openssl.org/)
BL-PA100A_OI.book  Page 18  Thursday, March 16, 2006  4:14 PM 
						

							19[For assistance, please call: 1-800-272-7033]
Useful Information
4. The names OpenSSL Toolkit and OpenSSL Project 
must not be used to endorse or promote products derived 
from this software without prior written permission. For 
written permission, please contact 
[email protected].
5. Products derived from this software may not be called 
OpenSSL nor may OpenSSL appear in their names 
without prior written permission of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain the 
following acknowledgment:
This product includes software developed by the OpenSSL 
Project for use in the OpenSSL Toolkit 
(http://www.openssl.org/)
THIS SOFTWARE IS PROVIDED BY THE OpenSSL 
PROJECT AS IS AND ANY EXPRESSED OR IMPLIED 
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 
IMPLIED WARRANTIES OF MERCHANTABILITY AND 
FITNESS FOR A PARTICULAR PURPOSE ARE 
DISCLAIMED.IN NO EVENT SHALL THE OpenSSL 
PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR 
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, 
EXEMPLARY, OR CONSEQUENTIAL DAMAGES 
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT 
OF SUBSTITUTE GOODS OR SERVICES; LOSS OF 
USE, DATA, OR PROFITS; OR BUSINESS 
INTERRUPTION) HOWEVER CAUSED AND ON ANY 
THEORY OF LIABILITY, WHETHER IN CONTRACT, 
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE 
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE 
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 
POSSIBILITY OF SUCH DAMAGE.
============================================
Some parts of the OpenSSL are provided with the following 
copyright notices with license noted above.
Copyright (c) 1998-2000 The OpenSSL Project.All rights 
reserved.
Some parts of the OpenSSL are provided with the following 
notice.
============================================
rijndael-alg-fst.c
@version 3.0 (December 2000)
Optimised ANSI C code for the Rijndael cipher (now AES)
@author Vincent Rijmen 

@author Antoon Bosselaers 

@author Paulo Barreto 
This code is hereby placed in the public domain.
THIS SOFTWARE IS PROVIDED BY THE AUTHORS AS 
IS AND ANY EXPRESS OR IMPLIED WARRANTIES, 
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS 
FOR A PARTICULAR PURPOSE ARE DISCLAIMED.IN NO EVENT SHALL THE AUTHORS OR CONTRIBUTORS 
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, 
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 
DAMAGES (INCLUDING, BUT NOT LIMITED TO, 
PROCUREMENT OF SUBSTITUTE GOODS OR 
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR 
BUSINESS INTERRUPTION) HOWEVER CAUSED AND 
ON ANY THEORY OF LIABILITY, WHETHER IN 
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING 
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 
OUT OF THE USE OF THIS SOFTWARE, EVEN IF 
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
============================================

============================================ 
Copyright (C) 1995-1998 Eric Young 
([email protected])All rights reserved.
This package is an SSL implementation written by Eric 
Young ([email protected]).
The implementation was written so as to conform with 
Netscapes SSL.
This library is free for commercial and non-commercial use 
as long as the following conditions are aheared to.The 
following conditions apply to all code found in this 
distribution, be it the RC4, RSA, lhash, DES, etc., code; not 
just the SSL code.The SSL documentation included with 
this distribution is covered by the same copyright terms 
except that the holder is Tim Hudson ([email protected]).
Copyright remains Eric Youngs, and as such any Copyright 
notices in the code are not to be removed.
If this package is used in a product, Eric Young should be 
given attribution as the author of the parts of the library 
used. This can be in the form of a textual message at 
program startup or in documentation (online or textual) 
provided with the package.
Redistribution and use in source and binary forms, with or 
without modification, are permitted provided that the 
following conditions are met:
1. Redistributions of source code must retain the copyright 
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above 
copyright notice, this list of conditions and the following 
disclaimer in the documentation and/or other materials 
provided with the distribution.
3. All adver tising materials mentioning features or use of 
this software must display the following acknowledgement:
This product includes cryptographic software written by 
Eric Young ([email protected])
The word cryptographic can be left out if the rouines from 
the library being used are not cryptographic related :-).
4. If you include any Windows specific code (or a derivative 
thereof) from the apps directory (application code) you must 
include an acknowledgement:
This product includes software written by Tim Hudson 
([email protected])
BL-PA100A_OI.book  Page 19  Thursday, March 16, 2006  4:14 PM 
						

							20
Useful Information
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG AS 
IS AND ANY EXPRESS OR IMPLIED WARRANTIES, 
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS 
FOR A PARTICULAR PURPOSE ARE DISCLAIMED.IN 
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS 
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, 
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 
DAMAGES (INCLUDING, BUT NOT LIMITED TO, 
PROCUREMENT OF SUBSTITUTE GOODS OR 
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR 
BUSINESS INTERRUPTION) HOWEVER CAUSED AND 
ON ANY THEORY OF LIABILITY, WHETHER IN 
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING 
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 
OUT OF THE USE OF THIS SOFTWARE, EVEN IF 
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The licence and distribution terms for any publically 
available version or derivative of this code cannot be 
changed.i.e. this code cannot simply be copied and put 
under another distribution licence [including the GNU Public 
Licence.]
============================================ 

============================================
Copyright (c) 1990 The Regents of the University of 
California.
All rights reserved.
Redistribution and use in source and binary forms are 
permitted provided that the above copyright notice and this 
paragraph are duplicated in all such forms and that any 
documentation, and other materials related to such 
distribution and use acknowledge that the software was 
developed by the University of California, Berkeley.The 
name of the University may not be used to endorse or 
promote products derived from this software without 
specific prior written permission. THIS SOFTWARE IS 
PROVIDED AS IS AND WITHOUT ANY EXPRESS OR 
IMPLIED WARRANTIES, INCLUDING, WITHOUT 
LIMITATION, THE IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR 
PURPOSE.
============================================
Copyright (c) 1990 The Regents of the University of 
California.
All rights reserved.
Redistribution and use in source and binary forms are 
permitted provided that the above copyright notice and this 
paragraph are duplicated in all such forms and that any 
documentation, advertising materials, and other materials 
related to such distribution and use acknowledge that the 
software was developed by the University of California, 
Berkeley.The name of the University may not be used to 
endorse or promote products derived from this software 
without specific prior written permission. THIS SOFTWARE IS PROVIDED AS IS AND WITHOUT ANY EXPRESS OR 
IMPLIED WARRANTIES, INCLUDING, WITHOUT 
LIMITATION, THE IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR 
PURPOSE.
============================================
Copyright (c) 1981, 1983, 1986, 1988, 1989, 1991, 1992, 
1993, 1994 
The Regents of the University of California.
All rights reserved.
Redistribution and use in source and binary forms, with or 
without
modification, are permitted provided that the following 
conditions are met:
1. Redistributions of source code must retain the above 
copyright notice, this list of conditions and the following 
disclaimer.
2. Redistributions in binary form must reproduce the above 
copyright notice, this list of conditions and the following 
disclaimer in the documentation and/or other materials 
provided with the distribution.
3. All adver tising materials mentioning features or use of 
this software must display the following acknowledgement:
This product includes software developed by the University 
of California, Berkeley and its contributors.
4. Neither the name of the University nor the names of its 
contributors may be used to endorse or promote products 
derived from this software without specific prior written 
permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND 
CONTRIBUTORS AS IS AND ANY EXPRESS OR 
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY 
AND FITNESS FOR A PARTICULAR PURPOSE ARE 
DISCLAIMED.IN NO EVENT SHALL THE REGENTS OR 
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, 
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT 
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR 
BUSINESS INTERRUPTION) HOWEVER CAUSED AND 
ON ANY THEORY OF LIABILITY, WHETHER IN 
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING 
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 
OUT OF THE USE OF THIS SOFTWARE, EVEN IF 
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
============================================
Copyright (c) 1988, 1990, 1993 Regents of the University of 
California.
All rights reserved.
Redistribution and use in source and binary forms, with or 
without modification, are permitted provided that the 
following conditions are met:
BL-PA100A_OI.book  Page 20  Thursday, March 16, 2006  4:14 PM