Panasonic Hd Plasma Display Th 65phd8 Operating Instructions
Have a look at the manual Panasonic Hd Plasma Display Th 65phd8 Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
31 SIDE BAR ADJUST 1 Press to select the SIDE BAR ADJUST. Press to select OFF, DARK, MID, BRIGHT. Press to exit from SCREENSAVER. 2 Do not display a picture in NORMAL mode for an extended period, as this can cause an after-image to remain on the side bars on either side of the display fi eld. To reduce the risk of such an after-image, change the brightness of the side bars. Display the SCREENSAVER screen. (Refer to the previous page, operation guide steps 1 and 2) Notes: • To reduce the occurrence of after-images, set the SIDE BAR ADJUST to BRIGHT. • The side bar may fl ash (alternate black/white) depending on the picture being shown on the screen. Using Cinema mode will reduce such fl ashing.side bars NORMAL mode after-images AB Picture out Picture Picture and PictureNon picture area This function may be applicable to the non-picture area. OFF MID BRIGHTDARK SCREENSAVER (For preventing after-images ) SCREENSAVER START FUNCTION MODE WOBBLING PEAK LIMIT FINISH TIME START TIMEWHITE BAR SCROLL OFF 6:15 12:30 OFF OFF SIDE BAR ADJUSTBRIGHT PRESENT TIME OF DAY 99:99
32 Reduces power consumption Press to select “POWER SAVE” “STANDBY SAVE” “POWER MANAGEMENT” “AUTO POWER OFF”. Press to select “ON” or “OFF”. On Off Press to exit from SET UP. • POWER SAVE: When this function is turned ON, luminous level of the Plasma Display is suppressed, so power consumption is reduced. • STANDBY SAVE: When this function is turned ON, power consumption of the microcomputer is reduced during power supply standby (see page 13-15), so standby power of the set is reduced. • POWER MANAGEMENT: The unit power supply is turned ON or OFF depending on whether or not there is a signal during PC input mode. This function is enabled when it is turned ON. (Only during input from PC(Mini D-sub) terminal) • AUTO POWER OFF: Equipment power supply is turned OFF when there is no signal. When this is set to On, the power supply of the unit goes Off 10 minutes after the input signals stop. This function is effective for input signals except input from PC (Mini D-sub) terminal. Press to select INPUT LABEL. Press to change the INPUT LABEL. Customizing the Input labels This function can change the label of the Input signal to be displayed. Note: While selecting a Input signal through Optional Terminal Board connected to Slot 1, Slot 2 and Slot 3, the Input label will depend on each Optional Terminal Board. INPUT LABELS for Slot 1, Slot 2, Slot 3 and miniD-sub: [Slot1 Input] INPUT1/VIDEO1/COMPONENT1/RGB1/DIGITAL1/PC1/DVD1/CATV1/VCR1/STB1 [Slot2 Input] INPUT2/VIDEO2/COMPONENT2/RGB2/DIGITAL2/PC2/DVD2/CATV2/VCR2/STB2 [Slot3 Input] INPUT3/VIDEO3/COMPONENT3/RGB3/PC3/DVD3/CATV3/VCR3/STB3 [PC (MiniD-sub) input] PC/COMPONENT/RGB/DVD/STB Note: “POWER MANAGEMENT” and “AUTO POWER OFF” are effective during normal viewing (one picture screen) only. 1/2 PC OFF STANDBY SAVE OFF POWER MANAGEMENTOFF AUTO POWER OFF OFF OSD LANGUAGEENGLISH ( US) COMPONENT/RGB-IN SELECT RGB INPUT LABELSIGNAL POWER SAVE SET UP 1/2 PC OFF STANDBY SAVE OFF POWER MANAGEMENTOFF AUTO POWER OFF OFF OSD LANGUAGEENGLISH ( US) COMPONENT/RGB-IN SELECT RGB INPUT LABELSIGNAL POWER SAVE SET UP 1 2 3
33 SET UP for MULTI DISPLAY By lining up Plasma Displays in groups of 4, 9 or 16 as illustrated below, an enlarged picture may be displayed across all screens. For this mode of operation, each plasma display has to be set up with a Display number to determine its location. Press to display the SET UP menu. Press to select the MULTI DISPLAY SETUP. Press to display the “MULTI DISPLAY SETUP” menu. Press to select the MULTI DISPLAY SETUP. Press to select “ON” or “OFF”. How to setup MULTI DISPLAY group of 16 (4 × 4 (F)) group of 4 (2 × 2 (F)) group of 9 (3 × 3 (F)) 1 2 3 2/2SET UP SCREENSAVER MULTI DISPLAY SETUP SET UP TIMER PRESENT TIME SETUP 2 × 2 A1 LOCATION MULTI DISPLAY SETUP ARRANGEMENTOFF MULTI DISPLAY SETUP Two options are selectable for MULTI DISPLAY (See next page).
34 SET UP for MULTI DISPLAY Press to select ARRANGEMENT (2nd step). Press to select “2 × 2”, “2 × 2F”, “3 × 3”, “3 × 3F”, “4 × 4”, “4 × 4F”. Press to select LOCATION. Press to select the required arrangement number. (A1-D4 : Refer to the following) How to set the Display location number for each Plasma Display Display Number locations for each arrangement. Press twice to exit from SET UP. 4 5 LOCATION MULTI DISPLAY SETUP ARRANGEMENTOFF 2 × 2 A1 MULTI DISPLAY SETUP 2 × 2 A1 LOCATION MULTI DISPLAY SETUP ARRANGEMENTOFF MULTI DISPLAY SETUP ( 2 × 2 (F) ) ( 3 × 3 (F) )( 4 × 4 (F) ) 6 Two options are selectable for MULTI DISPLAY. • To hide joints between TVs. • To show joints between TVs. (2 × 2, 3 × 3, 4 × 4) (2 × 2F, 3 × 3F, 4 × 4F) Suitable for moving image display. Suitable for still image display. Option F for MULTI DISPLAY
35 SET UP for MULTI DISPLAY ID Remote Control Function You can set the remote control ID when you want to use this remote control on one of several different TVs. 1 2 3Switch to on the right side. Press the button on the remote control. Press one of - , for the tens digit setting. Press one of - , for the units digit setting. 4 Notes: • The numbers in 2, 3 and 4 should be set up quickly. • Adjustable ID number range is 0 - 99. • If a number button is pressed more than two times, the fi rst two numbers become the ID number for the remote control. ID Cancellation Press button on remote control. (This has the same effect as pressing the , , buttons at the same time.) Notes: • Set the Remote ID “On” to operate the ID remote control(see page 41). If remote ID is set to “On”, you can use the remote control without identical ID number during option menu display. (see page 41) • The ID remote control cannot be used when ID select is set to anything other than 0, and the remote control ID is not the same as the ID select number (see page 41). ID remote control button operation The operation is the same as normal remote control except for the button.
36 SET UP for Input Signals 3D Y/C FILTER – For NTSC AV images COMPONENT / RGB IN SELECT Select to match the signals from the source connected to the COMPONENT / RGB input terminals. Y, P B, PR signals “COMPONENT” R, G, B, HD, VD signals “RGB” Press to display the SET UP menu. Press to select the “COMPONENT / RGB-IN SELECT”. Press to select the desired mode. COMPONENT RGB Press to exit from adjust mode. Select “SIGNAL” from the “SET UP” menu during VIDEO (S VIDEO) input signal mode. (“SIGNAL [VIDEO]” menu is displayed.) Note: When ON, this setting only affects NTSC input signals. Note: Selection may not be possible, depending on which optional board is installed. 1 2 1/2 PC OFF STANDBY SAVE OFF POWER MANAGEMENTOFF AUTO POWER OFF OFF OSD LANGUAGEENGLISH ( US) COMPONENT/RGB-IN SELECT RGB INPUT LABELSIGNAL POWER SAVE SET UP 1/2 PC OFF STANDBY SAVE OFF POWER MANAGEMENTOFF AUTO POWER OFF OFF OSD LANGUAGEENGLISH ( US) COMPONENT/RGB-IN SELECT RGB INPUT LABELSIGNAL POWER SAVE SET UP 3D Y/C FILTER (NTSC) COLOR SYSTEM SIGNAL ON AUTO 3 : 2 PULLDOWN Panasonic AUTO (4 : 3)OFF NORMAL [ VIDEO ] VIDEO NR OFF 3 1 2 Press ACTION ( ) button Press to select the “3D Y/C FILTER (NTSC)”. Press to set ON / OFF. Press to exit from adjust mode.
37 3:2 PULLDOWN / VIDEO NR COLOR SYSTEM / Panasonic AUTO Select SIGNAL from the “SET UP” menu during VIDEO (S VIDEO) input signal mode.(“SIGNAL [VIDEO]” menu is displayed.) SET UP for Input Signals Press to select the “COLOR SYSTEM” or “Panasonic AUTO”. Press to select each function. If the image becomes unstable: With the system set on Auto, under conditions of low level or noisy input signals the image may in rare cases become unstable. Should this occur, set the system to match the format of the input signal. Press to select 3:2 PULLDOWN or VIDEO NR. Press to set ON/OFF. Press to exit from adjust mode. 3:2 PULLDOWN: When ON, the display attempts to reproduce a more natural interpretation of sources such as movie pictures, which are recorded at 24 frames per second. If the picture is not stable, turn the setting to OFF. Note: When ON, this setting only affects the following signal input: • NTSC / PAL signal input during “VIDEO (S VIDEO)” input signal. • 525i(480i) 625i(575i), 1125(1080)/60i signal input during “COMPONENT” input signal. VIDEO NR: Automatically reduces unwanted picture noise. Note: VIDEO NR cannot be adjusted while a PC signal is being applied. 1 2 Press ACTION ( ) button Mode Function COLOR SYSTEMSet the color system to match the input signal. If set to “AUTO”, the color system is determined automatically. AUTO SECAM M.NTSC NTSCPA L Panasonic AUTO (4 : 3 )Set to “NORMAL” to view 4:3 images in an unchanged format when Panasonic AUTO is selected. If you would like to view 4:3 images in Just format, set to “JUST”. 1/2 PC OFF STANDBY SAVE OFF POWER MANAGEMENTOFF AUTO POWER OFF OFF OSD LANGUAGEENGLISH ( US) COMPONENT/RGB-IN SELECT RGB INPUT LABELSIGNAL POWER SAVE SET UP 3D Y/C FILTER (NTSC) COLOR SYSTEM SIGNAL ON AUTO 3 : 2 PULLDOWN Panasonic AUTO (4 : 3)OFF NORMAL [ VIDEO ] VIDEO NR OFF 1/2 PC OFF STANDBY SAVE OFF POWER MANAGEMENTOFF AUTO POWER OFF OFF OSD LANGUAGEENGLISH ( US) COMPONENT/RGB-IN SELECT RGB INPUT LABELSIGNAL POWER SAVE SET UP 3D Y/C FILTER (NTSC) COLOR SYSTEM SIGNAL ON AUTO 3 : 2 PULLDOWN Panasonic AUTO (4 : 3)OFF NORMAL [ VIDEO ] VIDEO NR OFF SYNC VIDEO NR SIGNAL AUTO H-FREQ. V-FREQ.kHz Hz33.8 60.0 [ RGB ] 3 : 2 PULLDOWNOFF OFF 3 : 2 PULLDOWN VIDEO NR SIGNAL OFF OFF [ COMPONENT ] 3 : 2 PULLDOWN VIDEO NR SIGNAL OFF OFF H-FREQ. V-FREQ.kHz Hz33.8 60.0 [ Digital ] Press ACTION ( ) button
38 SET UP for Input Signals Select SIGNAL from the “SET UP” menu during RGB input signal. Press to adjust. Press to exit from adjust mode. SYNC Setting RGB sync signal Confi rm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT signal). AUTO: The H and V sync or synchronized signal are automatically selected. If both input, it is selected the H and V sync. ON G: Uses a synchronized signal on the Video G signal, which is input from the G connector. VBS: Uses a synchronized signal of Composite Sync input, which is input from the HD connector. Displays the H (Horizontal) / V (Vertical) frequencies. This display is valid only for RGB/PC and DVI input signal. Display range: Horizontal 15 - 110 kHz Vertical 48 - 120 Hz H-FREQ. (kHz) / V-FREQ. (Hz) 1/2 PC OFF STANDBY SAVE OFF POWER MANAGEMENTOFF AUTO POWER OFF OFF OSD LANGUAGEENGLISH ( US) COMPONENT/RGB-IN SELECT RGB INPUT LABELSIGNAL POWER SAVE SET UP SYNC VIDEO NR SIGNAL AUTO H-FREQ. V-FREQ.kHz Hz33.8 60.0 [ RGB ] 3 : 2 PULLDOWNOFF OFF SYNC AUTO SYNC ON G SYNC VBS H-FREQ. V-FREQ.kHz Hz33.8 60.0 1 2 Press ACTION ( ) button
39 Press to display the Setup menu. Press to select “OSD Language”. Press and hold until the Options menu is displayed. Press to select your preferred menu. Press to adjust the menu. Press to confi rm. Press to exit from Options menu. Press or button to switch between modes. Enable Disable Enable Switches the “Off-timer function” “On” Disable Switches the “Off-timer function” “Off” Note : When “Disable” is set, the Off-timer is cancelled. Press or button to switch between modes. Off User1 User2 User3 Off You can use all of the buttons on the remote control. User1 You can only use , , , , , , , buttons on remote control. User2 You can only use , , buttons on the remote control. User3 Locks all the buttons on the remote control. Press or button to switch between modes. Off Auto On Off Power is not transmitted to the slot power. Auto Power is transmitted to the slot power only when main power is on. On Power is transmitted to the slot power when main power is on or in the standby state. Note: In some cases, power is transmitted to the slot power when main power is on or in the standby state regardless of the slot power setting. Press or button to switch between modes. Off MENU&ENTER On Off All the buttons at the bottom of the main unit can be used. MENU & ENTER Locks MENU and ENTER buttons on bottom face of main unit. On Locks all the button on bottom face of main unit. Options Adjustments 2/2Options OffOff Off Off OffOff Off 0 Slot power V. lnstallation Rotate Remote ID Serial ID ID select Button lock Remocon User level 1/2Options Off-timer function Initial INPUTOnscreen displayEnable OnOff 1 2 3 5 4 6
40 Press or button to switch between modes. Off PC INPUT1 INPUT2 INPUT3 Locks the input switch operation. Notes: • Only the adjusted signal is displayed. (see page 18). • Signal can be displayed when the Terminal board is installed. • Input switch can be used when this is set to “Off”. • In two screen display mode, if anything other than “Off” is set, the value will be fi xed as the value input in the single screen display mode.Press or button to switch between modes. On Off On Displays all the following on screen. • Power on display • Input signal switch display • No signal display • Mute and the remaining time of off-timer after was pressed. Off Hides all the items above from view. Press or button to switch between modes. Off PC INPUT1 INPUT2 INPUT3 Adjusts the input signal when TV is turned on. Notes: • Only the adjusted signal is displayed. (see page 18). • Signal can be displayed when the Terminal board is installed. • This menu is available only when “INPUT lock” is “Off”. Press button to adjust the volume when TV is turned on. Off On Off Sets normal volume. On Sets your preferred volume. Notes: • When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range. • You can hear the changed volume regardless of your volume setting before opening the options menu if you adjust the volume when “Initial VOL level” is “On” and cursor is on the menu. Press button to adjust the maximum volume. Off On Off Sets auto maximum volume. On Sets your preferred maximum volume. Notes: • If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level” automatically becomes the same as the “Maximum VOL level”. • The volume display can go up to 63 regardless of the settings. • You can hear the changed volume regardless of your volume setting before opening the options menu if you adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu. Press or button to switch between modes. Off On Off Nullify all the settings adjusted. On Sets the color temperature for TV studio. Note: Valid only when the low is set as color temperature on screen adjustment. Options Adjustments 1/2Options Off-timer function INPUT lock Studio W/B Advanced PIP Display size Initial VOL level Maximum VOL level Initial INPUT Onscreen display Off Off Off Off Enable On Off 0 Off Off 0