Panasonic Hd Plasma Display Th 65phd7 Operating Instructions

31
Press to select “ON” or “OFF”.
ON 
 OFF Press to select
“POWER SAVE”
“STANDBY SAVE”
“POWER MANAGEMENT”
“AUTO POWER OFF”.
Reduces power consumption
• POWER SAVE:When this function is turned ON, luminous level of the plasma display is suppressed, so
power consumption is reduced.
• STANDBY SAVE:When this function is turned ON, power consumption of the microcomputer is reduced
during power supply standby (see page 13-15), so standby power of the set is reduced.
• POWER MANAGEMENT: The unit power supply is...

32
SET UP for MULTI DISPLAY
By lining up Plasma Displays in groups of 4, 9 or 16 as illustrated below, an enlarged picture may be displayed across all
screens.
For this mode of operation, each plasma display has to be set up with a Display number to determine its location.
Press to display the SET UP menu.
Press to display the “MULTI DISPLAY SETUP” menu. Press to select the MULTI DISPLAY SETUP.
Press to select the MULTI DISPLAY SETUP.
Press to select “ON” or “OFF”.
How to setup MULTI DISPLAY
group of 16...

33
SET UP for MULTI DISPLAY
Press to select ARRANGEMENT (2nd step).
Press to select “2 × 2”, “3 × 3”, “4 × 4”.
How to set the Display location number for each Plasma Display
Press to select LOCATION.
Press to select the required arrangement
number. (A1-D4 : Refer to the following)
Display Number locations for each arrangement.
Press twice to exit from SET UP.
Notes:
•The multi-display capability is functional for the following component signals:
525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 1125 (1080) /...

34
3D Y/C FILTER  – For NTSC AV images
SET UP for Input Signals
COMPONENT / RGB IN SELECT
Select to match the signals from the source connected to the COMPONENT / RGB input terminals.
Y,  P
B, PR signals    
“COMPONENT”
R, G, B, HD, VD signals  
  
“RGB”
Press to display the SET UP menu.
Press to select the “COMPONENT / RGB-IN SELECT”.
Press to select the desired mode.
COMPONENT 
 RGB
Press to exit from adjust mode.
Select “SIGNAL” from the “SET UP” menu during VIDEO (S VIDEO) input signal mode.
(“SIGNAL...

35
SET UP for Input Signals
COLOR SYSTEM / Panasonic AUTO
Select SIGNAL from the “SET UP” menu during VIDEO (S VIDEO) input
signal mode.(“SIGNAL [VIDEO]” menu is displayed.)
Press to select the “COLOR SYSTEM” or
“Panasonic AUTO”.
Press to select each function.
If the image becomes unstable:
With the system set on Auto, under conditions of
low level or noisy input signals the image may in
rare cases become unstable. Should this occur,
set the system to match the format of the input
signal.
Mode
COLOR...

36
Select SIGNAL from the “SET UP” menu during RGB input signal.
Press to adjust.
SYNC
Setting RGB sync signal
Confirm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT
signal).
AUTO:The H and V sync or synchronized signal are automatically selected. If
both input, it is selected the H and V sync.
ON G: Uses a synchronized signal on the Video G signal, which is input from
the G connector.
VBS: Uses a synchronized signal of Composite Sync input, which is input
from the HD...

37
Shipping condition
This function allows you to reset the unit to the factory setting.
1
2
3
4
Press to display the SET UP menu.
Press to select “OSD LANGEAGE”.
Press and hold till the SHIPPING menu is
displayed.
Press to select “YES”.
Press to confirm.
[from the unit]
1  Press the MENU button till the Setup menu is displayed.
2  Press the Volume Up“+” or Down“–” button to select “OSD LANGEAGE”.
3  Press and hold the ENTER button till the SHIPPING menu is displayed.
4  Press the Volume Up“+” or Down“–”...

38
Troubleshooting
Symptoms
Picture Sound
Before you call for service, determine the symptoms and make a few simple checks as shown below.
This Plasma Display uses special image processing. Hence a slight time lag may occur between image and audio,
depending on the type of input signal. However, this is not a malfunction.
Checks
No remote control operations can be performed.
A cracking sound is sometimes heard from the unit.
The top or bottom of the picture on the screen is cut
off when I use the zoom...

39
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning
cloth or a soft, lint-free cloth.
•If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water to which
a small amount of neutral detergent has been added, and then wipe it evenly with a dry cloth of the same type until the
surface is dry.
•Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise...

40
VIDEO/COMPONENT/RGB/PC input signals
VIDEO input [Applicable when Multi Screen and Digital Zoom]
Signal nameHorizontal Vertical
frequency(kHz) frequency(Hz)
1NTSC 15.73 59.94
2PAL 15.63 50.00
3PAL60 15.73 59.94
4SECAM 15.63 50.00
5Modified NTSC 15.73 59.94
Signal nameHorizontal Vertical
COMPONENTRGBPCWhen Multi Screen
frequency (kHz)frequency (Hz) and Digital Zoom
1525 (480) / 60i 15.73 59.94∗∗∗ ∗
2525 (480) / 60p 31.47 59.94∗∗
∗1∗
3625 (575) / 50i 15.63 50.00∗∗∗ ∗
4625 (575) / 50p 31.25 50.00∗∗∗ ∗...