Panasonic Hd Plasma Display Th 65pf9 Operating Instructions

11
RS-232C Conversion cable
  D-sub 9-pin female  Details
    R X D
    T X D
   GND
   •  Non use 
  
  Shorted 
 • NC
Connections
SERIAL Terminals connection
Notes:
•  Use the RS-232C cable to connect the computer to the Plasma Display.
•  The computer shown is for example purposes only.
•  Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface specifi cation, so that the Plasma Display can be controlled by a 
computer which is...

12
SLOT3
PR/CR/R PB/CB/BY/GAUDIORLCOMPONENT/RGB IN
AUDIO
OUT Y,  P
B,  PR,
OUTR
R
PB
Y
L
R
COMPONENT VIDEO OUT
DVI-D connection
Connections
COMPONENT / RGB connection & RGB signal (R, G, B)
SLOT2
AUDIODVI-D IN
Mini-plug (M3) DVI-D
video cable 
(Within 5 m) PC with DVI-D 
video out
Pin No.    Signal Name  Pin No.    Signal Name 
1T.M.D.S. data 2-13T.M.D.S. data 3+
2T.M.D.S. data 2+14+5 V DC
3T.M.D.S. data 2/4 shielded15Ground 
4T.M.D.S. data 4-16Hot plug sense 
5T.M.D.S. data 4+17T.M.D.S. data 0-
6DDC...

13
Power ON / OFF 
When the POWER is turned on for the fi rst 
time, the LANGUAGE selection screen is 
displayed.
From the second time on, language selection 
can be done from the setup menu. (see 
page 18)
Select the desired language using the   
or   
button and press the ACTION (  ) 
button.From the second time on, the screen 
shown below is displayed for a while 
(setting condition is an example).
English (UK)
Deutsch
Français
Italiano
Español
ENGLISH (US)
Русский
OSD LANGUAGE
SET SELECT
PCFULL...

14
R - STANDBY
G       POWER ONINPUT MENU ENTER+VOL
MENU Screen ON / OFF
Each time the MENU button is pressed, the menu screen will 
switch. (see page 16)
INPUT button
(INPUT1, INPUT2, INPUT3 and PC selection)
(see page 18)
Power Indicator
The Power Indicator will light.
• Power-OFF .... Indicator not illuminated (The unit 
will still consume some power 
as long as the power cord is still 
inserted into the wall outlet.)
• Standby .......... Red
• Power-ON ...... Green
• DPMS .............Orange (With PC...

15
Basic Controls
OFF  TIMER 90
1
2
3 PCNORMAL
Standby (ON / OFF) button
The Plasma Display must fi rst be plugged into the wall outlet and turned on at the power switch (see page 13).
Press ON to turn the Plasma Display On, from Standby mode. Press OFF to turn the Plasma Display Off 
to Standby mode.
SET UP button (see page 16, 17)
DIRECT INPUT buttons
Press the INPUT “1”, “2”, “3” or “PC” input mode selection button to 
select the INPUT mode.
This button is used to switch directly to INPUT mode.
These...

16
Normal Viewing PICTURE SETUP
SOUNDPOS. /SIZE
On-Screen Menu Displays
The MENU button on the unit can also be 
pressed.
Each time the MENU button is pressed, the 
menu screen will switch.
0
0
0
0
0
0
2.2 W/B LOW B BLACK EXTENSION
W/B HIGH B
W/B LOW R
AGC GAMMA INPUT LEVEL
W/B HIGH R
ADVANCED SETTINGS
NORMALNORMALIZE
OFF
To PICTURE adjust menu
(see page 24)
To ADVANCED  SETTINGS
(see page 24, 25)Press to select 
“ON”.
Press to enter 
ADVANCED 
SETTINGS.
1/2
PC
OFF
STANDBY SAVE
OFF
POWER MANAGEMENTOFF...

17
2  Press to access 
each adjust 
screen.
Press the R button to return 
to previous menu.
Press the R button to return to 
“SET UP” menu. Press to select 
POWER ON TIME / 
POWER OFF TIME.
Press to set up 
POWER ON TIME / 
POWER OFF TIME.
To PRESENT TIME SETUP.
(see page 28)
SYNC
VIDEO NR
SIGNAL
AUTO
H-FREQ.
V-FREQ.kHz
Hz33.8
60.0
[ 
RGB ]
3 : 2 PULLDOWNOFF
OFF3 : 2 PULLDOWN
VIDEO NR
SIGNAL
OFF
OFF
 [ 
COMPONENT ]
3D Y/C FILTER (NTSC)
COLOR SYSTEM
SIGNAL
ON
AUTO
3 : 2 PULLDOWNOFFPanasonic AUTO (4 :...

18
Initial selections
Selecting the On-Screen Menu Language Selecting the input signal
Press to display the SET UP menu.
Press to select OSD LANGUAGE.
Press to select your preferred language.
   Selectable languages
1/2
PC
OFF
STANDBY SAVE
OFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABELSIGNAL
POWER SAVE
SET UP
Select the input signals to be connected by installing the optional Terminal Boards.
Press to select the input signal to be played back...

19
ASPECT Controls
The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format 
picture.
Press repeatedly to move through the aspect options:
Notes:
•  For PC signal input, the mode switches between “NORMAL”, “ZOOM” and “FULL” only.
•  For a 1125 (1080) / 60i · 50i · 60p · 50p · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i, 750 (720) / 60p · 50p 
  signal input, the mode is set to “FULL” mode, and switching is not possible.
•  Panasonic AUTO can be...

20
Adjusting POS. /SIZE
0
NORMALNORMALIZE
AUTO SETUP
POS. /SIZE
V-POS
0
H-POS
V-SIZEDOT CLOCKH-SIZE
CLOCK PHASE
1:1 PIXEL MODEOFF
000
0
1Press to display the POS. /SIZE menu.
Press to select AUTO SETUP / H-POS / H-SIZE / V-POS / 
V-SIZE / DOT CLOCK / CLOCK PHASE / 1:1 PIXEL MODE.
Press to adjust POS. /SIZE.
Press to exit from adjust mode.During “VIDEO (S VIDEO)”,
“Digital”, “SDI” and “HDMI” input signal.
During “COMPONENT”, “RGB”
 and “PC” input signal.
3 2
Notes:
• Adjustment details are memorized...