Panasonic Hd Plasma Display Th 50phw3 Operating Instructions

							31
SET UP for Input Signals
COLOR SYSTEM / Panasonic AUTO
Select SIGNAL from the “SET UP” menu during VIDEO (S-VIDEO) input
signal mode.(“SIGNAL [VIDEO]” menu is displayed.)
Press to select the “COLOR SYSTEM” or
“Panasonic AUTO”.
SELECT
SET  UP
SIGNAL
COMPONENT/RGB-IN  SELECT
RGB
OSD  LANGUAGEENGLISH (
US)
RETURN
Mode
Color system
Pansonic AUTO
(4:3)Press to select each functions.
Function
Set the color system to match the input signal. If set to “AUTO”, the color system
is determined automatically.
Set to “NORMAL” to view 4:3 images in an unchanged format when
Panasonic AUTO is selected. If you would like to view 4:3 images in “Just”
format, set to “JUST”.
AUTO        PAL         SECAM        M NTSC        NTSC
CHANGE
SELECT
3D  Y/C  FILTER  (
NTSC)
COLOR  SYSTEM
Panasonic  AUTO  (
4:3)ON
AUTO
NORMAL
SIGNAL[ 
 VIDEO  ]
RETURN
Press  
(store) button 
						

							32
Select SIGNAL from the “SET UP” menu during RGB or PC input signal mode.
Press to select each item.
Press to adjust.
SIGNAL[
  RGB  ]
SYNC
PULL-IN  RANGE
H
-FREQ.                 kHz
V-FREQ.                  HzH & V
NARROW
31.5
60.0
CLAMP  POSITION
SIGNAL[
  PC  ]
SYNC
PULL-IN  RANGE
H
-FREQ.                 kHz
V-FREQ.                  HzH & V
NARROW
31.5
60.0
CLAMP  POSITION
The following operation methods are the same for both the SIGNAL [RGB]
and SIGNAL [PC].
SYNC
SYNCH & V
SYNCON  VIDEO
SYNCON  G
Setting RGB sync signal setting:
Confirm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT).
H&V:The H and V sync signals are input from the HD/VD (BNC) connector.
ON G: Uses a synchronized signal on the Video G signal, which is input
from the G (BNC) connector.
ON VIDEO: Compatible with the scart plug (Europe)
The composite video signal input from the VIDEO input terminal is
used by dividing the sync signals.
Sets the width for different frequencies.
(This setting is the same for both SIGNAL [RGB] and SIGNAL [PC].)
Setting PC sync signal setting:
Confirm that the input is set to PC INPUT (this setting is valid only for PC INPUT).
H&V: The H and V sync signals are input from the HD/VD (BNC) connector.
ON G: Uses a synchronized signal on the Video G signal, which is input from the G (BNC) connector.
PULL IN RANGE
PULL  IN  RANGE
WIDE
PULL  IN  RANGENARROW
Displays the H (Horizontal)/V (Vertical) frequencies.
This display is valid only for RGB input and PC input.
Display range:
Horizontal 15.5 - 110 kHz
Vertical 48 - 120 Hz
H-FREQ (kHz)/V-FREQ (Hz)
H-FREQ.                 kHz
V
-FREQ.                  Hz31.5
60.0
SET UP for Input Signals
CLAMP POSITION
SIGNAL[
  COMPONENT  ]
CLAMP  POSITION
Adjusts the clamp position.
The following operation methods are the same for “SIGNAL” menu during
COMPONENT, RGB and PC input signal mode.
Normally, these adjustments are set to appropriate levels and, therefore, do not
need to be altered.
CLAMP  POSITION 
						

							33
Troubleshooting
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Some parts of the screen do
not light up
After-images appear
Whirring sounds can be heard
from the display unit.
Plasma Display panel
Check
The plasma display panel is manufactured using an extremely high level of precision
technology, however, sometimes some parts of the screen may be missing picture
elements or have luminous spots. This is not a malfunction.
Do not allow a still picture to be displayed for an extended period, as this can
cause a permanent after-image to remain on the High Definition Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext
and images displayed in 4:3 mode.
Note:
The permanent after-image on the Plasma Display resulting from fixed image use
is not an operating defect and as such is not covered by the Warranty.
This product is not designed to display fixed images for extended periods of time.
The display unit is fitted with a cooling fan to dissipate heat generated during normal use.
The whirring sound is caused by rotation of the fan and is not a malfunction.
Symptoms
Checks
Electrical Appliances
Cars/Motorcycles
Fluorescent light
Volume
(Check whether the mute function has been
activated on the remote control.)
Not plugged into AC outlet
Not switched on
PICTURE and BIGHTNESS/Volume setting
(Check by pushing the power switch or
stand-by button on the remote control.)
If a signal with a non-applicable color system
format, or frequency is input, only the input
terminal indication is displayed.
Color controls set at minimum level.
Color system (see page 28, 29) Picture
Interface
Normal Picture
No Picture
No Picture
No Color
Sound
Noisy Sound
No Sound
No Sound
Normal Sound
Normal Sound 
						

							34
Specifications
TH-50PHD3
120 V AC, 50/60 Hz
Max. Amps  5.5 A
2.4 W
0.7 W
Drive method AC type
50-inch, 16:9 aspect ratio
3000:1
(Panel only) 500 cd / m
2
(As a set) 300 cd / m2
1106 mm (W) × 622 mm (H) × 1269 mm (diagonal)
No. of pixels
1,049,088 (1366 (W) × 768 (H)) [4,098 × 768 dots]
34 °F - 104 °F (0 °C - 40 °C)
20 % - 80 %
NTSC, PAL, PAL60, SECAM, Modified NTSC
525i (480i), 625i (575i), 525p (480p), 750p (720p), 1125i(1080i)
XGA display
VGA, SVGA
SXGA, UXGA (compressed)
Horizontal scanning frequency 15.5 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Video IN (BNC)
S-VIDEO IN (MINI DIN 4PIN)
AUDIO IN (RCA PIN JACK × 2)
Y/G (BNC)
P
B/B (BNC)
P
R/R (BNC)
HD (BNC)
VD (BNC)
AUDIO IN (RCA PIN JACK × 2)
(HIGH-DENSITY D-SUB 15PIN)
AUDIO IN (M3.5 JACK)
EXTERNAL CONTROL TERMINAL (D-SUB9PIN)
16W [8 W + 8 W] (10 % THD)
For TY-SP50PHD3W only1.0 Vp-p (75-ohm)
Y: 1 Vp-p (75-ohm), C: 0.286 Vp-p (75-ohm)
0.5 Vrms (high impedance)
1.0 Vp-p/composite (75-ohm)
0.7 Vp-p/non-composite (75-ohm)
0.7 Vp-p (75-ohm)
0.7 Vp-p (75-ohm)
1.0 - 5.0 Vp-p (high impedance)
1.0 - 5.0 Vp-p (high impedance)
0.5 Vrms (high impedance)
R,G,B/0.7 Vp-p (75-ohm)
HD, VD/1.0 - 5.0 Vp-p (high impedance)
0.5 Vrms (high impedance)
RS-232C COMPATIBLE
Power Source
Power Consumption
Normal use
Stand-by condition
Power off condition
Plasma Display panel
Contrast Ratio
Brightness Capability
Screen size
Operating condition
Temperature
Humidity
Applicable signals
Color System
Scanning format
PC signals
Connection terminals
AV
COMPONENT/RGB
PC
SERIAL
SPEAKERS (6 Ω) 
						

							35
TH-50PHD3
EUR646525
2 × AA  Size
TY-SP50PHD3W
TY-ST42PT1U
TY-ST42PW1
TY-ST42PF3
TY-WK42PV1
TY-WK42PR1
TY-CE42PS1
TY-UPS200
47.6” (1210mm) × 28.5” (724 mm) × 3.9” (98mm)
approx. 99.2 lbs (main unit only)
approx. 109.3 lbs (with speakers)
Accessories Supplied
Remote Control Transmitter
Batteries
Optional Supplied
Speakers
Pedestal
Wall stand
Mobile stand
Wall-hanging bracket
(vertical)
Wall-hanging bracket
(angled)
Ceiling unit
Terminal Cover
Dimensions
(W × D × H)
Weight (Mass)
Specifications
POWER     /R - STANDBY
G   POWER ONINPUT–   VOL      +28.5 (724 mm)
47.6 (1210 mm)
3.9
(98 mm)
Note:
Design and specifications are subject to change without notice. Weight and dimensions shown are approximate. 
						

							Printed in Japan
MBS0301S0(MS)
Customer’ Record
The model number and serial number of this product can be found on its rear panel. You should note this
serial number in the space provided below and retain this book, plus your purchase receipt, as a
permanent record of your purchase to aid in identification in the event of theft or loss, and for Warranty
Service purposes.
Panasonic Consumer Electronics
Company, Division of Matsushita
Electric Corporation of America
One Panasonic Way Secaucus
New Jersey 07094Panasonic Sales Company,
Division of Matsushita Electric
of Puerto Rico Inc. (“PSC”)
Ave. 65 de Infanteria, Km 9.5
San Gabriel Industrial Park,
Carolina, Puerto Rico 00985Panasonic Canada Inc.
5770 Ambler Drive
Mississauga, Ontario
L4W 2T3 Model Number          TH-50PHW3 Serial Number