Panasonic Hd Plasma Display Th 50phw3 Operating Instructions
Here you can view all the pages of manual Panasonic Hd Plasma Display Th 50phw3 Operating Instructions . The Panasonic manuals for Display are available online for free. You can easily download all the documents as PDF.
Page 11
11 Basic Controls R - STANDBY G POWER ONINPUT– VOL + TH-50PHW3 Main Power On/Off Switch Volume Adjustment Push the Volume Up “+” or Down “–” button to increase or decrease the sound volume level. Input button (VIDEO (S-VIDEO)/COMPONENT, RGB/PC Mode Selection) Push the “INPUT” button to select VIDEO(S-VIDEO)/COMPONENT or RGB/PC input signal modes sequentially. Power Indicator The Power Indicator will light. • Power-OFF ..... Indicator not illuminated (The unit will still consume some power as...
Page 12
12 Connections To tighten: Pull Pull To loosen: Push the knob S-VIDEOVIDEOVD HD PR/CR/R PB/CB/B Y/G L RL RAUDIO AUDIO AUDIO SERIAL TUNER IN PC IN COMPONENT/RGB IN AV IN AV IN Terminals (see page 13, 14)COMPONENT/RGB IN and Audio IN Terminals (see page 15)From SERIAL Terminal on Computer (see page 17) From EXIT monitor Terminal on Computer (see page 16) SPEAKER Terminals (R)SPEAKER Terminals (L) – Cable fixing bands Secure any excess cables with bands, as required. From TUNER signal out Terminal (see page...
Page 13
13 1 2 1 3 2 Remove the tubes from the ends of the speaker cables. Connections How to connect the speakers When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation. Luminance earth Luminance inChrominance earth Chrominance in S-VIDEO 4 pin socket (S-VIDEO VCR) Audio OUTVideo OUTS-Video OUT RL S-VIDEOVideo input to S-VIDEO socket Audio input to L/R sockets AUDIO 2×RCA audio cables S-VIDEOVIDEOL...
Page 14
14 Connections How to connect the AV Input Terminals VIDEO signal connection (VCR) Audio OUTVideo OUT RL VIDEO BNC video cableVideo input to BNC socket Audio input to L/R sockets AUDIO 2×RCA audio cables VIDEO RCA video cable (VCR) Audio OUTVideo OUT RL Video input to BNC socket RCA-BNC adapter plug S-VIDEOVIDEOL RAUDIO AV IN Audio input to L/R sockets AUDIO 2×RCA audio cables Notes: (1) Additional equipment and cables shown are not supplied with this set. (2) When connecting video cables, priority is...
Page 15
15 Connections How to connect the COMPONENT/RGB Input Terminals RGB signal (R, G, B, HD, VD) connection Notes: (1) Change the “COMPONENT/RGB-IN” setting in the “SET UP” menu to “Y/PB/PR”. (see page 30, 32) (2) Additional equipment and cables shown are not supplied with this set. Component signals (Y, P B, PR) connection Notes: (1) Change the “COMPONENT/RGB-IN” setting in the “SET UP” menu to “RGB”. (see page 30, 32) (2) Additional equipment and cables shown are not supplied with this set. VD HD PR/CR/R...
Page 16
16 Connections How to connect the PC Input Terminals Notes: (1) Computer signals which can be input are those with a horizontal scanning frequency of 15.5 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, signals cannot be displayed if signals exceeding 1200 lines will not be displayed properly.) (2) The display resolution is a maximum of 1024 × 768 dots when the aspect mode is set to “NORMAL”, and 1366 × 768 dots when the aspect mode is set to “FULL”. If the display resolution...
Page 17
17 Connections How to connect the SERIAL Terminals Notes: (1) Use the RS-232C cable to connect the computer to the High Definition Plasma Display. (2) The computers shown is for example purposes only. (3) Additional equipment and cables shown are not supplied with this set. SERIAL RS-232C cable D-sub 9p COMPUTER The SERIAL terminal is used when the High Definition Plasma Display is controlled by a computer. The SERIAL terminal conforms to the RS-232C interface specification, so that the High Definition...
Page 18
18 Power ON/OFF Connecting the plug to the Wall Outlet Push the POWER switch on the High Definition Plasma Display to turn the set on POWER-ON Power Indicator: Green Example: The screen below is displayed for a while after the High Definition Plasma Display is turned on. (setting condition is an example.) When the POWER is turned on for the first time, the LANGUAGE selection screen is displayed. From the second time on, language selection can be done from the setup menu. (see page 21) Select the desired...
Page 19
19 Select the Input Signal R - STANDBY G POWER ONINPUT— VOL + — VOL +INPUT Press the INPUT button to select the input video signal desired from equipment such as a VCR which has been connected to the High Definition Plasma Display. SURROUND VOL NR INPUT INPUT Power ON/OFF and Input Signal Selection Input signals will change as follows: For COMPONENT INPUT (see page 30) For RGB INPUT (see page 30) VIDEO COMPONENT PC VIDEO RGB PC
Page 20
20 On-Screen Menu Display from Remote Control PLASMA DISPLAY INPUT SURROUND VOL NR PICTURE SOUNDSET UP ASPECT PICTURE POS. /SIZE OFF TIMER PC PICTURE NORMALIZE PICTURE MENU BRIGHTNESS COLORSTANDARD 0 0 TINT COLOR TEMPNORMAL ADVANCED SETTINGSON PICTURE0 0 0 SHARPNESS NORMALIZENORMAL SELECTADJUSTRETURN To ADVANCED SETTINGS menu (see page 29) To PICTURE adjust menu (see page 28) NORMALIZENORMAL SELECT ADVANCED SETTINGS NORMALIZE BLACK EXTENSION W/B HIGH R W/B HIGH B0 0 0 0 W/B LOW R GAMMA2. 2 0...