Panasonic Hd Plasma Display Th 50pf9 Operating Instructions

21
Adjusting POS. /SIZE
While the POS. /SIZE display is active, if either the N button on the remote control is pressed at any time or the ACTION 
( ) button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
Helpful Hint (  
 / NORMALIZE 
 Normalization)
AUTO SETUPAutomatically adjust H-POS / V-POS / CLOCK PHASE / DOT CLOCK and set H-SIZE / V-SIZE the 
standard value when RGB signal is input.
Notes:
•  If the dot clock frequency is 162 MHz or higher, DOT...

22
ABABAB
BABABA
PC1
VIDEO2PC1
VIDEO2
VIDEO2
VIDEO1PC1
VIDEO2
A
A A
CB
B
B
D
MULTI PIPMULTI PIPMULTI PIP
SWAPSWAPSWAP
SELECT
Press repeatedly.
Each time pressing this button main picture and sub picture will be displayed 
as follows below.
Press to swap main 
picture and sub picture.
Press to select the input mode.
Under main Picture and sub picture display, select the 
picture which you would like to change input modes.
Notes:
•  The sub picture sound is heard while a sub picture 
operation is...

23
Advanced PIP
1
2
3
5
Press to select “OSD Language”.
Press and hold until the Options menu is displayed.
Press to adjust the menu.
Off : Sets normal two screen display mode
        (see page 22).
On : Sets Advanced PIP mode.
Press to confi rm.
Press to exit from 
Options menu.
4
6
Notes:
•  Advanced PIP corresponding signalOne screen  Advanced PIP
Main screen Sub screen
•  Sound output is from the picture which is selected in Audio OUT (PIP) (See page 26).
•  In 2 screen display, the same input mode...

24
2/2
ADVANCED SETTINGS COLOR TEMP
COLOR MANAGEMENTNORMAL
OFF
ON
PICTURE
1/2
25
0
0
0
5
PICTURE
NORMALNORMALIZESTANDARD
BRIGHTNESS
SHARPNESS PICTURE MENU
COLOR PICTURE
TINT
Press to select “ON”.
Press the left    or right     button to switch between modes.
STANDARD
For viewing in standard (evening lighting) environments.
This menu selects the normal levels of BRIGHTNESS 
and PICTURE.
DYNAMIC
For viewing in brighter environments.
This menu selects higher than normal levels of 
BRIGHTNESS and PICTURE....

25
ADVANCED SETTINGS
Notes:
•  “COLOR” and “TINT” settings cannot be 
adjusted for “RGB/PC” and “Digital” input 
signal.
•
  You can change the level of each function 
(PICTURE, BRIGHTNESS, COLOR, TINT, 
SHARPNESS) for each PICTURE MENU.
• The “TINT” setting can be adjusted 
for NTSC signal only during “VIDEO 
(S VIDEO)” input signal.
•  In PICTURE, there is not a noticeable change 
even when contrast is increased with a bright 
picture or reduced with a dark picture.
On the remote control unit, while...

26
0
0
0
SOUND
NORMALNORMALIZESTANDARD
OFF TREBLE AUDIO MENU
BALANCEBASS
0
MID
SURROUND
MAIN AUDIO OUT (PIP)
SOUND Adjustment
MUTE
BASS
Adjusts low pitch sounds
MID
Adjusts normal sounds
TREBLE
Adjusts pitch sounds
BALANCE
Adjusts left and right volumes
SURROUND
Select On or Off
Notes:
•  Press the SURROUND button to directly turn the surround effect ON and OFF. (see page 14)
•  BASS, MID, TREBLE and SURROUND settings are memorized separately for each AUDIO MENU.
1
Press to display the SOUND menu.
Press...

27
Digital Zoom
This displays an enlargement of the designated part of the displayed image.
Select the area of the image to be enlarged.
Press on the enlargement location to select.
Return to normal display (quit Digital Zoom).
Press to exit from the Digital Zoom.
Notes:
•  When power goes OFF (including “Off Timer” operation), Digital Zoom terminates.
•  The Digital Zoom function cannot be selected while in the following operation state:
  “Multi-viewer” (Picture in Picture, Picture out Picture, Picture...

28
PRESENT TIME SETUP / SET UP TIMER
PRESENT TIME SETUP
The timer can switch the Plasma Display ON or OFF.
Before attempting Timer Set, confi rm the PRESENT TIME OF DAY and adjust if necessary. 
Then set POWER ON TIME / POWER OFF TIME.
Press to display the SET UP menu.
Press to select SET UP TIMER or 
PRESENT TIME SETUP.
Press to display the SET UP TIMER screen or 
PRESENT TIME SETUP screen.
Display the PRESENT TIME SETUP screen.
To set up PRESENT TIME OF DAY, follow the procedure described below.
Press...

29
SET UP TIMER
Press to select 
POWER ON TIME / POWER OFF TIME.
Press to set up POWER ON TIME / POWER OFF 
TIME.
   button: Forward
   button: Back
Notes:
• Pressing “  ” or “  ” button once changes POWER ON TIME / POWER OFF TIME 
1minute.
• Pressing “  ” or “  ” button continuously changes POWER ON TIME / POWER OFF 
TIME by 15 minutes.
 
Press to select POWER ON FUNCTION 
/ POWER OFF FUNCTION. 
Press to select ON.
Press twice to exit from SET UP.
Note: 
Timer function will not work unless “PRESENT TIME...

30
Do not display a still picture, especially in NORMAL mode, for any length of time.
If the display must remain on, a SCREENSAVER should be used.
NEGATIVE / SCROLL selection
2
3 1
4
Press to display the SET UP menu.
Press to select the SCREENSAVER.
Press to select the SCREENSAVER screen.
Press to select the FUNCTION.
Press to select the desired function.
WHITE BAR SCROLL   NEGATIVE 
WHITE BAR SCROLL  : A white bar will scroll from left to right.
NEGATIVE    : A negative image will be displayed on the...