Panasonic Ey6950 Operating Instructions Manual

Cordless Hammer Drill Driver
Operating Instructions
Model No: EY6950
IMPORTANT
This manual contains safety information. Read manual completely before first using 
this product and save this manual for future use. 

- 2 - 
. GENERAL 
SAFETY RULES 
FOR ALL BAT-
TERY OPERATED 
TOOLS
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS.
 Failure to follow all instructions listed below,  may  result  in  electric  shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area
 1) Keep your work area clean and well lit. Cluttered  benches  and  dark  areas invite accidents.
 2) D o   n o t   o p e r a t e   p o w e r   t o o l s   i n  explosive  atmospheres,  such  as in  the  presence  of  flammable  liq-uids,...

- 3 -  
 14) Do  not  use  tool  if  switch  does  not turn it on or off. A  tool  that  cannot  be  controlled  with the  switch  is  dangerous  and  must  be repaired.
 15) Disconnect  battery  pack  from  tool  or place  the  switch  in  the  locked  or  off position  before  making  any  adjust-ments,  changing  accessories,  or  stor-ing the tool. S u c h   p r e v e n t i v e   s a f e t y   m e a s u r e s  reduce  the  risk  of  starting  the  tool accidentally.
 16) Store  idle  tools  out  of...

- 4 - 
  8) During  charging,  the  charger  may become  slightly  warm.  This  is  nor-mal. Do not charge the battery for a long period. 
Symbol meaning
VVolts
Direct Current
n0no load speed
…/minrevolutions orreciprocation per minutes
Forward Rotation
Reverse Rotation
Rotation with Hammering
Rotation only
WARNING;
Some  dust  created  by  power  sand-ing,  sawing,  grinding,  drilling,  and o t h e r   c o n s t r u c t i o n   a c t i v i t i e s   c o n-tains  chemicals  known  to  the  State of...

- 5 -  
RECOMMENDED MINIMUM AWG SIZE OFEXTENSION CORDS FORBATTERY CHARGERS
AC Input Rating.AmperesAWG Size of Cord
Equal to or greater thanBut less thanLength of Cord, Feet
2550100150
0218181816
 8) Do not operate charger with damaged cord  or  plugreplace  them  immedi-ately.
 9) Do  not  operate  charger  if  it  has  re-ceived a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. 
 10) Do not disassemble charger; take it to a  qualified  serviceman  when...

- 6 - 
.FUNCTIONAL DESCRIPTION
Clutch handle
Keyless drill chuck
Variable speed control trigger
18V Battery pack (EY9251)
Speed selector switch
Vent holes
Forward/Reverse 
lever
Battery pack release button
Battery charger (EY0110)Support handle
. ASSEMBLY
Attaching or removing bit
Note: When  attaching  or  removing a  bit,  disconnect  battery  pack from  tool  or  place  the  switch  in the center position (switch lock).This  tool  is  equipped  with  a  keyless drill chuck.
 1. Attachment 
Insert  the...

- 7 -  
Attaching  or  removing  battery 
pack
 1. To connect the battery pack: Insert  the  battery  pack.  It  snaps  into place to indicate proper connection.
 2. To remove the battery pack: Press  the  two  buttons  on  the  sides of  the  battery  pack.    Slide  the  battery pack out of the tool body.
 3. Support handleP l a c e   t h e   s u p p o r t   h a n d l e   a t   y o u r  favorite  position  and  tighten  the  han-dle securely. 
Loosen Tighten
Remove  the  handles  when  placing the...

- 8 - 
Bit-locking function
 1. With  the  trigger  switch  not  engaged and  a  screwdriver  bit  locked  in  place, the  tool  can  be  used  as  a  manual screwdriver  (up  to  22.6  Nm,  230  k
f-cm, 199 in-lbs).
   There  will  be  a  little  play  in  the  chuck, but this is not a malfunction.
 2. This  feature  is  handy  for  tightening screws  that  require  more  torque  than the maximum torque of the driver (po-sition   on  the  clutch),  for  confirming the  tightness  of  a  screw  or  to...

- 9 -  
e x t r e m e l y   s h o r t   a f t e r   r e c h a r g i n g ,  replace  the  battery  pack  with  a  new one.Note: Use  under  extremely  hot  or c o l d   c o n d i t i o n s   w i l l   r e d u c e  operating capacity per charge.
Charging
Note: When  you  charge  the  battery pack  for  the  first  time,  or  after prolonged  storage,  charge  it for about 24 hours to bring the batteries up to full capacity.
EY0110
 1. Plug the charger into the AC outlet.
Note:  S p a r k s   m a y   b e...

- 10 - 
. LAMP INDICATIONS
Red Flashing
Red Lit
Flashing quickly
Orange Lit
Orange Flashing
Charger is plugged into a wall outlet. Ready to charge.
Now charging
Charging is completed.
Battery pack is warm. Charging will beginwhen temperature of battery pack drops.
Charging is not possible. Clogged with dust or malfunction of the battery pack.
. MAINTENANCE
Use only a dry, soft cloth for wiping the unit. Do not use a damp cloth, thinner, ben-zine, or other volatile solvents for cleaning.
BATTERY...