Panasonic Ey6932 Operating Instructions Manual

Cordless Hammer Drill Driver
Operating Instructions
Model No: EY6932
IMPORTANT
This manual contains safety information. Read manual completely before first using 
this product and save this manual for future use. 

- 2 - 
. GENERAL SAFETY
 RULES 
FOR ALL BATTERY
OPERATED
TOOLS
WARNING!Read and understand all instructions. Failure to follow all instructions listed below,  may  result  in  electric  shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area
 1) Keep  your  work  area  clean  and well lit. Cluttered  benches  and  dark  areas invite accidents.
 2) Do  not  operate  power  tools  in e x p l o s i v e   a t m o s p h e r e s ,   s u c h  as in the presence of flammable liquids, gases,...

- 3 -  
 13) Do not force tool. Use the correct tool for your application.  The  correct  tool  will  do  the  job  bet-ter and safer at the rate for which it is designed.
 14) Do  not  use  tool  if  switch  does not turn it on or off. A  tool  that  cannot  be  controlled with  the  switch  is  dangerous  and must be repaired.
 15) Disconnect  battery  pack  from  tool or  place  the  switch  in  the  locked or  off  position  before  making  any adjustments, changing accessories, or storing the tool....

- 4 - 
  8) D u r i n g   c h a r g i n g ,   t h e   c h a r g e r  may  become  slightly  warm.  This is  normal.  Do  not  charge  the  bat-tery for a long period. 
Symbol meaning
VVolts
Direct Current
n0no load speed
…/minrevolutions orreciprocation per minutes
Forward Rotation
Reverse Rotation
Rotation with Hammering
Rotation only
WARNING;
Some  dust  created  by  power  sand-ing,  sawing,  grinding,  drilling,  and o t h e r   c o n s t r u c t i o n   a c t i v i t i e s   c o n-tains  chemicals...

- 5 -  
 7) An  extension  cord  should  not  be used unless absolutely necessary. Use  of  improper  extension  cord could  result  in  a  risk  of  fire  and electric  shock.  If  extension  cord must be used, make sure: a. that  pins  on  plug  of  extension cord  are  the  same  number,  size and  shape  as  those  of  plug  on charger.b. t h a t   e x t e n s i o n   c o r d   i s   p r o p-erly  wired  and  in  good  electrical condition.c. that  wire  size  is  large  enough for  ampere  rating...

- 6 - 
. FUNCTIONAL DESCRIPTION
Clutch handle
Keyless drill chuck
Variable speed control trigger
15.6V Battery pack (EY9231)
Speed selector switch
Vent holes
Forward/Reverse lever
Battery pack release button
Battery charger (EY0230)
. ASSEMBLY
Attaching or removing bit
Note: When  attaching  or  removing a  bit,  disconnect  battery  pack from  tool  or  place  the  switch  in the center position (switch lock).This  tool  is  equipped  with  a  keyless drill chuck.
 1. Attachment Insert  the  bit  and...

- 7 -  
Attaching or removing battery 
pack
 1. To connect the battery pack: Insert the battery pack. It snaps into place to indicate proper connection.
 2. To remove the battery pack: Press  the  two  buttons  on  the  sides of  the  battery  pack.    Slide  the  bat-
tery pack out of the tool body.
. OPERATION
Switch Operation
 1. T h e   s p e e d   i n c r e a s e s   w i t h   t h e  amount of depression of the trigger.  When  beginning  work,  depress  the trigger  slightly  to  start  the...

- 8 - 
Bit-locking function
 1. With  the  trigger  switch  not  engaged a n d   a   s c r e w d r i v e r   b i t   l o c k e d   i n  place,  the  tool  can  be  used  as  a manual screwdriver (up to 22.6 Nm, 230 kf-cm, 199 in-lbs).
   There  will  be  a  little  play  in  the chuck, but this is not a malfunction.
 2. This  feature  is  handy  for  tightening 
screws  that  require  more  torque than  the  maximum  torque  of  the driver  (position   on  the  clutch),  for confirming  the  tightness...

- 9 -  
Battery pack
To AC outlet
Battery charger
 3. During  charging,  the  charging  lamp will be lit.   When  charging  is  completed,  an internal  electronic  switch  will  au-tomatically  be  triggered  to  prevent overcharging. Charging will not start if the battery pack is warm (for example, immedi-ately after heavy-duty operation). The  orange  standby  lamp  will  be lit  until  the  battery  cools  down.  Charging  will  then  begin  automati-cally.
 4. When  charging  is  completed,  the...

- 10 - 
. MAINTENANCE
Use  only  a  dry,  soft  cloth  for  wiping the  unit.  Do  not  use  a  damp  cloth, thinner,  benzine,  or  other  volatile  sol-vents for cleaning.
BATTERY RECYCLING
ATTENTION:
A  nickel  metal  hydride  battery  that  is recyclable  powers  the  product  you have purchased. Please  call 1-800-8-BATTERY  for information  on  how  to  recycle  this battery.
. ACCESSORIES
Use only bits suitable for size of drill’s chuck.
RECOMMENDED SPEED SELECTION
CAUTION:  U S E   AT   L O W   S...