Panasonic Ew 3037 Operating Instructions

							20
Setting (checking) the measurement notification time 
19
M/R
Calling up readings from memory
Readings can be recalled after being saved without
having to switch the unit on.
1. Press the Memory/Recall button.
•The average readings of all recorded measurements
are displayed.
•The  mark will be displayed (Fig. 11-a).
•When, for example, readings from 90 measurements
have been saved the average of the readings from 90
measurements will be displayed.
2. Press the Memory/Recall button to display readings
starting with from the most recent measurement.
•Each time the Memory/Recall button is pressed
readings are displayed in order of the most recent
measurement (Fig. 11-c, 11-d).
•No readings will be displayed when there are none in
the memory.
3.Press the On/Off and Start button to switch off the
unit.
If you forget to switch off the unit it will do so
automatically after approx. 30 seconds.
Deleting all data stored in memory
(1) Recall stored data using the Memory/Recall button.
(2)Press the Memory/Recall button again and hold it (for approx. 3
seconds) until all readings are deleted.
NOTE: Readings from individual measurements cannot be deleted.
(3)When data has been deleted the  mark and  will be
displayed on the screen.
Fig. 11-a
Fig. 11-c Fig. 11-b
Fig. 11-dTo let you take measurements at the same time every
day, 3 times per day can be set as notification times. 
1. Press the Set button on the top surface of the blood
pressure monitor (Fig. 12-a). 
•Notification Time 1 will blink (Fig. 12-b).
*If date and time have not been set, the display will
change to the date/time setting display.
2. Press the Set button again.
•The  and  will blink (Fig. 12-c).
3. Press the Adjust button to display  . 
•The  and  will blink (Fig. 12-d). 
•Notification sound will sound. 
•Notification sound will not sound. 
•When  is displayed and the Set button is 
pressed, the time becomes  and the 
and will light.
4.(1)Press the Set button. The hour value will blink
(Fig. 12-e). 
(2)Press the Adjust button repeatedly to set the
desired hour.Fig. 12-a
Fig. 12-c Fig. 12-b
Fig. 12-d
Fig. 12-e (After approx.
one second.)
&864@&OH
 
 

 
Ö”´
 
						

							22 21
5. (1) Oprima el botón Puesta. El valor de los minutos
destellará (Fig. 12-f).
(2)Oprima el botón Ajustar repetidamente para
establecer los minutos deseados.
•Para ajustar sólo la Hora de Notificación 1,
oprima el botón Arrancar/Parar para comletar el
ajuste.
•Para ajustar las Horas de Notificación 2 y 3, siga
los pasos 6 y 7 de más abajo.
6Oprima el botón Puesta. La Hora de Notificación 2
destellará (Fig. 12-g). Repita los pasos 2 a 5 para
establecer la hora de notificación deseada.
7Cuando se ha completado el ajuste de la Hora de
Notificación 2, oprima el botón Puesta. La Hora de
Notificación 3 destellará. Repita los pasos 2 a 5 para
establecer la hora de notificación deseada.
8Cuando el ajuste de la Hora de Notificación 3 ha sido
completado, oprima el botón Puesta. Las horas
ajustadas para las Horas de Notificación 1 a 3 serán
mostradas automáticamente a intervalos de 2
segundos (Fig. 12-h).
9Para completar el ajuste, oprima el botón
Arrancar/Parar.To change the notification time setting: 
1. Press the Set button on the top surface of the blood pressure monitor.
(Notification Time 1 will blink.) 
•To change the setting for Notification Time 2 or 3, press the Change
button to display Notification Time 2 or 3. 
2. Press the Set button twice. The hour value will blink. 
3. Press the Adjust button repeatedly to set the desired hour. 
4. (1) Press the Set button. The minute value will blink 
(2) Press the Adjust button repeatedly to set the desired minute. 
5. Press the Start/Stop button to complete the setting. 
To cancel the measurement notification sound: 
1. Press the Set button on the top surface of the blood pressure monitor.
(Notification Time 1 will blink.) 
•To change the setting for Notification Time 2 or 3, press the Adjust button
to display Notification Time 2 or 3. 
2. Press the Set button once. The  and  will blink. 
3. Press the Adjust button.  will be displayed. 
4. Press the Start/Stop button to complete the setting. 
•When the set time is reached, the measurement notification sound will
sound to notify you that its time to take a measurement. 
•If the set time is reached in the middle of taking a measurement, the
measurement notification sound will not sound. 
•When the measurement notification sound sounds, it can be stopped by
pressing the Start/Stop button. If the button is not pressed, the sound
stops after 1 minute. 
•If the blood pressure monitor is put into a bag, desk, etc., it may not be
possible to hear the measurement notification sound. 
Advice: 
If a record table is made of the measurement values taken around the same 
time, you can easily see your own daily blood pressure changes. Fig. 12-f
Fig. 12-g
Fig. 12-h
Fig. 12-i
&864@&OH
 
 

 
Ö”´
 
						

							24 23
Troubleshooting
Display
The “E” blinks on
the display 
Status before error
Pressurization to above
280 mmHgwas
performed.
(Re-pressurization was
performed several
times.)
Pressure decreased
suddenly and 
appeared in the display.
mark only blinks a
few times, or not at all.
Cuff does not inflate.
Check points
Check whether
measurements are
being taken correctly
and whether you are
assuming the correct
posture. Make sure
the unit is on the palm
side of the wrist. 
(See pages 12-13.)
Check whether the
pressure cuff is
attached to your wrist
correctly. Make sure
the unit is on the palm
side of the wrist.
(See page 12.)
Care and Maintenance
1. Use a dry, soft cloth to clean the device. If desired, use a cloth lightly
dampened with tap water and a mild detergent to clean the device. 
DO NOT use alcohol, benzine, thinner or other harsh chemicals to clean
the device or cuff.
2. When the unit will not be used for a long time (30 days or more), be sure
to remove the batteries. Otherwise, the batteries may leak and damage
the unit.
Storing the Monitor
1. Fold the pressure cuff as indicated.
(Fig. 13-a)
2.Put the blood pressure monitor in
the storage case. (Fig. 13-b)
•Be sure not to pinch the pressure
cuff or 2cm gauge when closing the
case.
1
2
0
8
0
If the 2cm gauge is attached, 
straighten it out.
Fig. 13-a
Fig. 13-b
NOTE:When the batteries are removed, the date, time, and measurement
record are erased. Set the date and time again the next time you
use the unit.
&864@&OH
 
 

 
Ö”´
 
						

							26 25
Specifications
Method of measurement:
Display:
Measuring range:
Measurement accuracy:
Power source:
Operating environment:
Storage environment:
Wrist circumference
measurement range:
Dimensions (H#W#D):
Weight:
Oscillometric System
Digital LCD
Blood pressure: 0 - 280 mmHg
Pulse rate: 30 - 160 pulse/min.
Pressure: ±3 mmHg
Pulse rate: ±5%
Two 1.5-volt alkaline (AAA/LR03) batteries
10°C to 40°C (50°F to 104°F)
30% to 85% RH
-20°C to 60°C (-4°F to 140°F)
10% to 95% RH
12.5 to 22.0 cm (5 to 8-3/4)
54.0#83. 0#26.0 mm 
(2-1/8#2-1/4#1-1/32)
90 g(3.2 oz.) not including batteries
If the unit still appears to provide unusual or erroneous readings,
consult your physician. If the unit does not appear to be functioning
properly, contact Panasonic at 1-800-338-0552
.
Specifications are subject to change without notice.
Symptom
The systolic pressure
value or diastolic
pressure value is high. 
The systolic pressure
value or diastolic
pressure value is low. 
The measured values
differ significantly.
The measured value
differs from that
measured by the doctor.
The measured value is
different for each
measurement.
Varying sounds and
pressurization speeds
occur during inflation of
the cuff. 
The measured value
obtained is different
from that measured at
the upper arm.
Possible cause
•The hand with the cuff was held too low and
not at heart level. (See page 12)
•The cuff was not attached properly. (See
page 12.)
•You moved your hand or body or you spoke
during measurement. (See page 12.)
•The hand with the cuff was held too high and
not at heart level. (See page 12.)
•You moved your hand or body or you spoke
during measurement. (See page 12.)
•Your posture was not the same for all
measurements, or measurements were
taken without sufficient time in between.
Always wait approximately 5 minutes before
taking another reading, and above all, relax.
•Blood pressure varies in response to
minute changes in your mental state, such
as your reaction to your doctor taking the
measurement. One way to check this is to
bring the unit to your doctor’s office and
directly compare the readings taken by
your physician.
•Relax for at least 5 minutes and then take
another measurement.
•Changes in operating sounds and
pressurization speeds are normal and occur
due to the fact that measurements are
being made as the cuff is being inflated.
•For persons with certain circulation problems,
there may be substantial differences in
blood pressure values measured at the
upper arm versus at the wrist.
&864@&OH
 
 

 
Ö”´