Panasonic Electronic Board Ub T880 Operating Instructions

							51
Operating Instructions
Installation Manual
1
10.Turn off the power switch and unplug the 
power cord from the AC outlet.
11 .Wipe the screen board surface.
•Gently wipe the screen board surface with a soft, 
moist cloth.
Notice
•Do not use thinner, benzene, or abrasive 
chemicals to clean. 
(Doing so can result in discoloration.)
•Do not wipe the screen board with a dry 
cloth. 
(Doing so can cause static electricity build-
up.)
UB-T880-PJQXC0337ZA_mst.book  51 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							Installation Manual
52 Operating Instructions
For Mounting on a Stand KX-B061 
(Sold Separately)
1.Attach the power cord.
•Connect the power cord to the elite Panaboard 
before installing on the stand.
2.Depending on the location of the outlet, install 
the power cord as illustrated in the following 
diagrams.
•When attaching the power cord downward.
•When attaching the power cord along the lower 
side of the elite Panaboard.
3.Hang the elite Panaboard on the stand with the 
screw heads.
4.Secure the elite Panaboard to the stand frame 
using the two-wing bolts (M5 × 12 mm [1/2in.] 
[2 count]) included with the stand.
Power Cord
UB-T880-PJQXC0337ZA_mst.book  52 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							53
Operating Instructions
Installation Manual
1
•When installing the elite Panaboard on the 
stand, you can adjust its height to 4 different 
levels. 
When changing the height, remove the left 
and right screws from the back of the elite 
Panaboard, and securely insert them at the 
desired height. Torque (greater than 1 N • m 
[10 k gf•cm (9 lbf•in.)]).
5.Confirm that the elite Panaboard can operate.
•See “Confirming the elite Panaboard Operation” 
(page 54).
6.Turn off the power switch and unplug the 
power cord from the AC outlet.
7.Wipe the screen board surface.
•Gently wipe the screen board surface with a soft, 
moist cloth.
Notice
•Do not use thinner, benzene, or abrasive 
chemicals to clean. 
(Doing so can result in discoloration.)
•Do not wipe the screen board with a dry 
cloth. 
(Doing so can cause static electricity build-
up.)
elite Panaboard 
Height  Screw Position
-100 mm (-3
7/8in.) Highest
Standard 2nd from top
+100 mm (+3
7/8in.) 2nd from bottom
+200 mm (+7
7/8in.) Lowest
UB-T880-PJQXC0337ZA_mst.book  53 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							Installation Manual
54Operating Instructions
Confirming the elite Panaboard Operation
After assembling the elite Panaboard, confirm that it operates properly by following the procedure below.
Confirming the Interactive Features
1.Following the procedure in “Installing the elite Panaboard software/book” (page 22), install the 
software and connect the included USB cable.
2.Confirm that the interactive features are operating correctly.
•If a projector is not available, confirm operation using only the elite Panaboard and computer.
•When the elite Panaboard software starts, the calibration screen is displayed on the computer screen.
•Perform tentative calibration by touching each of the following points on the elite Panaboard with your 
finger for about 2 seconds, one point after another. For precise adjustment, it is necessary to use a 
projector.
•Confirm operation by writing on the screen board with the electronic pen and checking that the writing is 
displayed on the computer’s screen. (Your writing with the electronic pen will not appear on the screen 
board itself.)Action
Checkpoints
Operation Measure
1 Turn on the power.  Power LED (green) lights. (Normal operation)
Power LED (green) does not 
light, or Error LED (red) is 
blinking. Check the power cord.
See step 1 of “Assembling the elite Panaboard”.
•For Wall Mounting 
→  page 49
•For Mounting on a Stand KX-B061 (Sold 
Separately)  →   page 52
1
34
2
Approx. 100 mm (37/8in.)
Approx. 100 mm (3
7/8in.)
UB-T880-PJQXC0337ZA_mst.book  54 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							Installation Manual
55Operating Instructions
1
Repackaging
To repackage the elite Panaboard, perform steps in the following “Assembling the elite Panaboard” in 
reverse.
•For Wall Mounting →  page 49
•For Mounting on a Stand KX-B061 (Sold Separately)  →  page 52
Package the unit as depicted in the diagram in “Preparing for Removing the elite Panaboard from Its 
Packaging” (page 48).
Notice
•When handling the electronic board, hold it by the frame and not the screen board. (Holding the screen 
board can result in damage.)
UB-T880-PJQXC0337ZA_mst.book  55 ページ  ２０１０年５月１１日　火曜日　午後１時９分 
						

							1731
(For EU only)
© Panasonic System Networks Co., Ltd. 2010 F0510E1060
Information for Users on Collection and Disposal of Old Equipment and used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and 
electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable 
collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any 
potential negative effects on human health and the environment which could otherwise arise from inappropriate 
waste handling.
For more information about collection and recycling of old products and batteries, please contact your local 
municipality, your waste disposal service or the point of sale where you purchased the items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further 
information.
Information on Disposal in other Countries outside the European Union
These symbols are only valid in the European Union. If you wish to discard these items, please contact your 
local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement 
set by the Directive for the chemical involved.
UB-T880-PJQXC0337YA_mst.book  56 ページ  ２０１０年５月３１日　月曜日　午後４時３０分