Panasonic Electronic Board Ub 780bp Operating Instructions

•After calibration has completed, the  icon
is displayed in the notification area, and the
Desktop Drawing Tool is automatically
displayed.
[Desktop Drawing Tool]
• You will be able to use elite Panaboard
software.
Note
•The Desktop Drawing Tool shown above is
an example from version 3.1 of the elite
Panaboard software.
• For detailed information about using the
elite Panaboard software, refer to the
included electronic manual or the help
menu. For instructions on viewing the
electronic documentation...

Viewing the Electronic
Documentation
Follow the procedure below to view the electronic
documentation  "Operating Instructions (For Software) ".
1. Turn on your computer and start Windows.
2. Open "Operating Instructions (For Software)"
from the Start menu.
([Start]  ® [All Programs]  ® [Panasonic]  ® [elite
Panaboard]  ® [Operating Instructions for
Software])
• The electronic documentation will be displayed.
• For Windows 2000, [Programs] is displayed
instead of [All Programs].
Note
•To...

Daily CareWhen cleaning the elite Panaboard or inside the elite Panaboard, make sure to disconnect the USB cable.Cleaning the elite Panaboard
Gently wipe the elite Panaboard with a soft, moist cloth.
Notice•The elite Panaboard is designed exclusively for
projector images.
• For spots that are difficult to remove, use
commercially available white-board cleaner or
neutral household cleaner diluted with water.
• Do not use thinner, benzene, or abrasive
chemicals to clean.
(Doing so can result in...

Replacing the Penpoint of the
Electronic Pen
As the penpoint of the electronic pen becomes worn, a
hole will appear in the penpoint. Continuing to use the
electronic pen in this condition can cause damage to
the screen or unsatisfactory operation, so replace the
penpoint with a new one as soon as possible.24Operating Instructions (For Basic Operations)Appendix  

TroubleshootingWhen experiencing problems, please refer to the table below for possible solutions. If the problem persists,
contact your dealer.SymptomPossible cause and solutionSee
pageThe LEDs do not light
when the USB cable is
connected to a computer.Check that the USB cable is properly connected.
→ If the problem persists, disconnect the USB cable from the
computer, and connect it again.
–Red LED is blinking.
Disconnect the USB cable from the computer, and connect it
again.
→ If the problem persists,...

SymptomPossible cause and solutionSee
page
Extra lines are displayed
on the computer screen.
Apart from writing directly on the elite Panaboard with the
electronic pen, you pushed the penpoint with your finger while
holding it close to the elite Panaboard.
→ Avoid pushing the penpoint with your finger.
–
The message "The pen
battery is low. Replace the
battery soon."  is displayed
on the computer screen.
The electronic pen’s battery is weak.
→ Replace the electronic pen’s battery.14
23Marks...

SpecificationsModel NumberUB-T780BPGeneralPowerSupplied by the USB bus (AC power connection is not
required).Power Consumption5 V / 500 mA (USB BUS Power)External Dimensions: Height
´  Width  ´ Depth1,340 mm  ´ 1,752 mm  ´ 89 mm
(4 ft. 4  3
/4  in.  ´ 5 ft. 9 in.  ´ 3  1
/2  in.)Weight25 k g (55.11 lbs)Operating EnvironmentTemperature: 15 °C to 35 °C (59 °F to 95 °F)
Humidity: 30 % to 80 %Storage EnvironmentTemperature: -20 °C to 40 °C (-4 °F to 104 °F)
Humidity: 15 % to 80 %InterfaceUSB 2.0Input...

Supplies & AccessoriesOptional DeviceElectronic PenUE-608025StandKX-B061
•To purchase separately sold items, contact your dealer.
28Operating Instructions (For Basic Operations)Appendix 

Installation Manual (for qualified service personnel)•Request assembly of the Electronic Board, stand and wall mounting from your dealer.
• Before constructing or installing the elite Panaboard, please read  "Installation Manual (for qualified service
personnel)" carefully.
Especially, please read "For Your Safety" carefully and install the elite Panaboard safely.
Panasonic System Networks Co., Ltd. cannot be held responsible for accidents or damage to property
resulting from incorrect...

Have the unit installed, removed and
disposed of only by qualified service
personnel.After installing or moving the electronic
board, lock the casters and set the
fall-prevention extension legs.If the unit is hung on a wall, confirm the
wall must be capable of supporting at
least the following weight.
1,324 N (135 k gf)Do not attach the electronic board to
mortared walls. Accidental electric
leakage from the wall mounting plate
bolts to metal laths or wire laths can
cause heat, smoke or a fire.Confirm...