Panasonic Dvd Home Theater Sound System Sc Ptx7 Operating Instructions

							RQT8926
101
Page
(Continued on the next page) During play, a “humming” 
sound can be heard.≥Are there power cords or fluorescent lights near any connected cords? Keep this 
unit as far away as possible from other electrical devices.—
I can’t connect to the 
network.≥Has the LAN cable come unplugged? Check that the LAN cable is properly 
connected.
≥Have you plugged in a modular cable for use with a telephone into the LAN 
terminal on this unit? Connect with a straight LAN cable.
≥Is the power for the modem or broadband router turned on? Turn the power on for 
each device.
≥Have you set the unit to use only the internal CD database? Set “CD database 
Setting” to “Yes” in “Network” menu. 
≥Is there a mistake in the network settings? Follow any instructions you may have 
received from your ISP (Internet Service Provider) and make changes to the 
settings accordingly.
≥Are the broadband router settings correct? Read the operating instructions for the 
broadband router.
≥Is the broadband router and/or modem correctly connected? Check the operating 
instructions for each device and connect accordingly.20
20
—
94
—
—
—
While using my PC, I cannot 
connect to the network.≥Does your Internet Service Provider (ISP) or service contract prevent multiple 
terminals connecting at the same time? Check the content and regulations of your 
contract.—
You have forgotten your 
ratings password.
Reset all the settings in “Setup 
for Video”  to Factory Preset.≥Switch the selector to “DVD/CD”, and when the unit is stopped, simultaneously 
press [∫] on the main unit and [S10] on the remote control until “Initialized” is 
displayed. All settings in “Setup for Video” will return to the default values.—
The SUB MENU button 
doesn’t work.≥Is the unit performing the recording? Perform operations after recording finishes.—
General IssuesEZ Sync
EZ Sync “HDAVI Control” 
does not work.≥Check the connection of the HDMI cable.
≥Is “EZ Sync” set to “On” in the  “HDMI” menu?
≥Check the EZ Sync settings on the connected device.
≥If the HDMI device connection was changed, there has been a power failure, or the 
plug was removed and then reinserted to the power outlet, EZ Sync may stop 
working. In any of these cases, perform the steps listed below.
1 Turn on the power to all devices connected with an HDMI cable, and then turn the 
TV (VIERA) off and on again.
2 Turn the EZ Sync settings on the TV(VIERA) to “Off” and then “On” again. (For 
more information, refer to the VIERA operating instructions.)
3 Switch the VIERA input to the HDMI connection with this unit, and after this unit’s 
screen is displayed, check the EZ Sync operations.17
 93
—
—
Playback IssuesOperation
Recorded tracks are not 
displayed, and cannot be 
found. ≥If it is difficult to find the playlist that a track was added to, search by the name of 
the track. All tracks in the Music Collection will be displayed by track name.  47
Tracks have not been added 
to “Music Shuffle”.≥Are you playing the track immediately after recording it? Adding the track to Music 
Shuffle takes place when the unit is in standby mode.
≥Does this abnormality only occur with specific tracks? Depending on the track, it 
may not be added to any genre.—
49
The display does not change 
even after inserting a disc.
Play does not begin even 
after pressing [1](PLAY).≥Does the inserted disc conform to disc standards and specifications? Replace it 
with a disc that conforms to disc standards.
≥Condensation has formed: Wait 1 to 2 hours for it to evaporate.24
—
Reference
Reference
PTX79P.book  Page 101  Monday, April 9, 2007  9:24 AM 
						

							RQT8926
102
Troubleshooting guide
Playback IssuesOperationPage
Play doesn’t start.≥This unit may not play WMA that contains still picture data.
≥If a disc contains CD-DA and other formats, proper playback may not be possible. —
—
It takes time before play 
starts.≥Play may take time to begin when an MP3 track has still picture data. Even after the 
track starts, the correct play time will not be displayed; however, this is normal. —
Specific locations will not 
play correctly.≥Is the disc dirty or scratched? Wipe off the disc with a soft cloth, etc. and try again.26
WMA/MP3 discs are not read 
correctly.≥If you have created a multi-session disc, did you close the session? Use WMA/MP3 
discs that have closed sessions.
≥Is there one session with very little data on it? Create sessions with approximately 
5 MB (approximately two three-minute tracks) or larger.—
—
Menu doesn’t appear.
 [VCD] with playback control≥Press [∫] twice and then press [1](PLAY).—
The program and random 
play functions do not work.≥These functions do not work with some DVD-Videos.—
Play restarts from the 
beginning of the track when 
soundtrack is changed.≥This is normal on DVD-Audio.—
Subtitle position is wrong. ≥Adjust the position. (“Subtitle Position” in Display Menu) 60
No subtitles.≥Display the subtitles. 57
The subtitles overlap closed 
captions recorded on discs.≥Clear the subtitles. 57
In A-B Repeat, point B is 
automatically set.≥The end of an item becomes point B when it is reached.59
Repeat play is automatically 
canceled.≥Repeat play may be canceled when you perform “Advanced Disc Review”.—
Playback IssuesSound
No sound.≥There may be a pause in sound when you change the play speed.
≥Audio may not be heard when more than 4 devices are connected with HDMI 
cables. Reduce the number of connected devices.—
—
Sound distorted.≥Noise may occur when playing WMA files.
≥The DVD-Audio disc may have restrictions on the method of audio output. With 
some multi-channel DVD-Audio discs, unless the number of connected speakers is 
the same as the disc’s channel specification, audio will not be output properly. 
Refer to the DVD-Audio disc’s jacket for more information.
≥With HDMI AV OUT connections, audio may not be output from other terminals in 
the way that was set.—
—
—
The track sounds different 
now than it did before.≥Did you make the recording to the HDD while the recording mode was set to AAC? 
Tracks are recorded to the HDD in LPCM and then converted to AAC. Playing a 
track directly after recording it will cause the audio to sound different from the 
converted  AAC track.32
The audio sounds broken up 
between tracks.≥Was the track recorded in AAC (LP)? In rare cases, the audio may sound broken 
up between tracks recorded in AAC (LP).—
Effects do not work.≥Are you trying to use various audio qualities and effects for sound fields at the 
same time? Depending on how the audio quality and sound fields are grouped 
together, you may not be able to obtain enough of an effect.
≥None of the audio effects work when the unit is outputting bitstream signals from 
the DIGITAL OPTICAL OUT terminal. 
≥Some audio effects do not work or have less effect with some discs.—
18
—
The on-screen menu shows 
“2” as a soundtrack option,  
but the audio does not 
change. ≥This is normal on DVD-Audio. Even if a second soundtrack isn’t recorded, two 
numbers will be shown.—
PTX79P.book  Page 102  Monday, April 9, 2007  9:24 AM 
						

							RQT8926
103
Playback IssuesPicturePage
Picture distorted.≥Ensure that the unit is not connected through a video cassette recorder. 
≥Have you selected an item in “Video Output Mode”
 that is incompatible with the 
connected equipment? Depending on the current connection status, perform 
corresponding steps.
–When connecting to a television that is incompatible with progressive output using 
the COMPONENT VIDEO OUT terminal:
Press and hold [CANCEL] until the picture displays correctly. The settings will 
return to “480i”.
–When connecting to a television with an HDMI cable:
Press and hold [CANCEL] until the picture displays correctly. The settings will 
return to “480p”.18
60
Picture size doesn’t fit the 
screen.≥Change “TV Aspect” in “Video” menu. 
≥Use the television to change the aspect. If your television does not have that 
function, change “4:3 Aspect” in Display Menu. 
≥Change the Zoom setting. 92
60
56
The television may display 
incorrectly or colors appear 
faded.≥PAL discs cannot be played. (You can play DVD-Audio; however, still pictures may 
be displayed enlarged.)
≥Connect to a progressive output compatible television to enjoy progressive video.
≥Picture may not be seen when more than 4 devices are connected with HDMI 
cables. Reduce the number of connected devices.—
—
—
Menu not displayed 
correctly.≥Restore the zoom ratio to a1.00. 
≥Set “Subtitle Position” in Display Menu to “0”. 
≥Set “4:3 Aspect” in Display Menu to “Normal”. 56
60
60
Auto zoom function does not 
work well.≥Turn off TV’s zoom function.
≥Use the other preset aspect ratios or manual adjustment. 
≥Zoom function may not work well, especially in dark scenes and may not work 
depending on the type of disc.—
56
—
Playback IssuesHDMI and progressive
Video is not output from 
HDMI AV OUT.≥Please use HDMI cables that have the HDMI logo (as shown on the cover).
≥Change the HDMI video output settings by using the procedure below.
–Connect the television using VIDEO OUT terminal, then set “Video Mode” to “On” 
in the “HDMI” menu. —
93
While “HDMI Status” 
displayed, any items are not 
underlined.≥If you select an item without an “¢” in the “Video Output Mode” in Picture Menu, it 
will not be underlined.60
Picture distorted.≥Please use HDMI cables that have the HDMI logo (as shown on the cover).
≥Have you selected an item in “Video Output Mode”
 that is incompatible with the 
connected equipment? Depending on the current connection status, perform 
corresponding steps.
–When connecting to a television that is incompatible with progressive output using 
the COMPONENT VIDEO OUT terminal:
Press and hold [CANCEL] until the picture displays correctly. The settings will 
return to “480i”.
–When connecting to a television with an HDMI cable:
Press and hold [CANCEL] until the picture displays correctly. The settings will 
return to “480p”.—
60
There is ghosting when 
HDMI or progressive output 
is on.≥This problem is caused by the editing method or material used on DVD-Video, but 
should be corrected if you use interlaced output.
– When using the COMPONENT VIDEO OUT terminal, set “Video Output Mode” in 
Picture Menu to “480i”. (Alternatively, press and hold [CANCEL] to switch to 
“480i”.)
– When using the HDMI AV OUT terminal, set “Video Output Mode” in Picture 
Menu to “480i” output marked with an “¢”. Else, disable the HDMI AV OUT 
connection and use other video connections. Make the settings in the following 
order:
1 Set “Video Mode” in the “HDMI” menu to “Off ”.
2 Set “Video Output Mode” in Picture Menu to “480i”. (Alternatively, press and 
hold [CANCEL] to switch to “480i”.)60
93
60
Pictures not in progressive 
output.≥If the unit is connected to the television through VIDEO OUT, output will be 
interlace.—
Closed captions not 
displayed.≥When progressive output or HDMI output is on, closed captions will not be 
displayed.—
Reference
Reference
PTX79P.book  Page 103  Monday, April 9, 2007  9:24 AM 
						

							RQT8926
104
Troubleshooting guide
Recording IssuesPage
Cannot record.≥Is the selector set to “TV Audio” (when “TV Audio Input” is set to “DIGITAL IN”) or 
“XM”? You cannot record tracks from these sources to the HDD.
≥Is the CD set to random or repeat play mode? Turn random/repeat play off.—
 57, 
58
Cannot perform high-speed 
recording.≥Did you try to record WMA/MP3 tracks from a recordable disc? WMA/MP3 tracks 
cannot be recorded in high-speed recording mode.—
Tried to record tracks to the 
HDD, but they were not 
recorded.≥If the track you are trying to record  is an SCMS recording, it will be skipped.35
During recording, the audio 
is jumpy or there is noise in 
the recording.  ≥Does the readable surface of the disc have any scratches or fingerprints? Replace 
the disc if there are scratches, and wipe the disc off with a soft cloth if there are 
fingerprints. 
≥Depending on how the disc was recorded, you cannot record tracks correctly from 
some recordable discs. 26
—
Radio
Noise is heard.
Sound is distorted.
“ST” is flashing or doesn’t 
light during FM broadcasts.≥This is being caused by weak signal reception.
When listening to FM radio, try the following operations.
– Adjust the position of the FM antenna. 
– Use an FM outdoor antenna.
– Change “Audio Mode” to “Mono”.
When listening to AM radio, try the following operations.
– Adjust the position of the AM antenna.
– Use an AM outdoor antenna.
– Try switching “BP” (Beat Proof Function).—
63
62
—
63
62
A beat sound is heard.≥Turn the television off or separate it from the unit.—
A low hum is heard during 
AM broadcasts.≥Separate the antenna from other cables and cords.—
You can receive only 
promotional XM channels≥Your 
XM Satellite service has not been activated, or your subscription has expired.
To activate your XM Satellite service, or to renew your subscription:– For U.S. residents, visit XM on the Web at www.xmradio.com or call XM’s Listener 
Care at 1-800-XMRADIO (1-800-967-2346). 
– For Canada residents, visit 
XM on the Web at www.xmradio.ca or call XM’s Listener 
Care at 1-877-GET-XMSR (1-877-438-9677).You should have your Radio ID ready.64
Gracenote database
The title information 
obtained from the Gracenote 
database or WMA/MP3 titles 
display incorrectly. The title 
does not display all 
characters.≥The title may contain characters that are not supported by this unit. Letters of the 
alphabet can be displayed. Letters with accent mark (such as “é”, etc.) will be 
displayed blank or not displayed correctly.
≥Does the track have a long name? This unit can display titles up to 59 characters in 
length (artist names only, up to 39 characters).—
69
Newly released CD title 
information cannot be 
obtained.≥Is the unit connected to a network? Newly released CD title information may not 
have been added to the internal Gracenote database. Connect to a network to 
search for the newest titles.20
PTX79P.book  Page 104  Monday, April 9, 2007  9:24 AM 
						

							RQT8926
105
MEMO
Reference
Reference
PTX79P.book  Page 105  Monday, April 9, 2007  9:24 AM 
						

							RQT8926
106
Specifications 
RMS TTL Power Output300W
Front Ch 50 W per channel (8≠), 1 kHz, 10 % THD
Center Ch 50 W per channel (8≠), 1 kHz, 10 % THD
Subwoofer Ch 100 W (4≠), 100 Hz, 10 % THD
FTC TTL Power Output240W
Front Ch
40 W per channel (8 ≠), 120 Hz–20 kHz, 1 % THD
Center Ch
40 W per channel (8 ≠), 120 Hz–20 kHz, 1 % THD
Subwoofer Ch 80 W (4 ≠), 45 Hz–120 Hz, 1% THD
Frequency range87.9–107.9 MHz (200 kHz step)
87.5–108.0 MHz (100 kHz step)
Antenna terminals75≠ (unbalanced)
AM Frequency range520 – 1710 kHz (10 kHz step)
Internal HDD capacity80 GB
Recording formatAAC/Linear PCM
MP3/WMA (LAN–PC)
Bit rate (AAC)128 kbps (XP) /96 kbps (SP) /64 kbps (LP)
Channel2 channels (stereo)
Recording time
AAC  Approx. 2460 hours (LP mode)
Linear PCM Approx. 104 hoursPlayable discs [8 cm (3z) or 12 cm (5z)]
(1) DVD (DVD-Video, DVD-Audio)
(2) DVD-RAM (DVD-VR, MP3
§2, 5, JPEG§4, 5)
(3) DVD-R (DVD-VR, DVD-Video, MP3§2, 5, JPEG§4, 5)
(4) DVD-R DL (DVD-VR§6, DVD-Video)
(5) DVD-RW (DVD-VR, DVD-Video, MP3§2, 5, JPEG§4, 5)
(6)iR/iRW (Video)
(7)iR DL (Video)
(8) CD, CD-R/RW [CD-DA, Video CD, SVCD
§1, MP3§2, 5, 
WMA§3, 5, JPEG§4, 5, HighMAT Level 2 (Audio and 
Image)]
§1 Conforming to IEC62107§2 MPEG-1 Layer 3, MPEG-2 Layer 3§3Windows Media Audio Ver.9.0 L3
Not compatible with Multiple Bit Rate (MBR)
§4Exif Ver 2.1 JPEG Baseline files
Picture resolution: between 160k120 and 6144k4096 
pixels (Sub sampling is 4:2:2 or 4:2:0). Extremely long 
and slender pictures may not be displayed.
§5The total combined maximum number of recognizable 
audio and picture contents and groups: 4000 audio and 
picture contents and 400 groups.
§6Discs recorded on DVD recorders or DVD video cameras 
using Version 1.2 of the Video Recording Format  (a 
unified video recording standard).
Pick up
Wave length (DVD/CD) 662 nm/785 nm
Laser power (DVD/CD)
[For[U.S.A.[ CLASS II/CLASS I[For[Canada[ CLASS 1/CLASS 1M
Video systemNTSC
Video output
Output level 1 Vp-p (75≠)
Output connector Pin jack (1 system)
Component video output (480p/480i)
Y output level 1 Vp-p (75≠)
P
B output level 0.7 Vp-p (75≠)
PR output level 0.7 Vp-p (75≠)
Output connector
Pin jack (Y: green, P
B: blue, PR: red) (1 system)
HDMI AV outputHDMI 19 pin type A connector 
This unit supports “HDAVI Control 2” function.
AMPLIFIER SECTION
FM TUNER SECTION
AM TUNER SECTION
HDD SECTION
DISC SECTION
VIDEO SECTION
PTX79P.book  Page 106  Monday, April 9, 2007  9:24 AM 
						

							RQT8926
107
[Front\&\center\channel\SB-FCX7]
∫Front speaker section
Ty p eMechanical 2 way, 1 speaker system (Bass reflex)
Full range6.5 cm (2
1/2z) Cone type
Impedance/Input power (IEC)8≠/50 W§7 (Max)
Output sound pressure82 dB/W (1.0 m)
Frequency range85 Hz – 25 kHz (j16 dB)
100 Hz – 22 kHz (j10 dB)
∫Center speaker section
Ty p e1 way, 1 speaker system (Closed)
Full range6.5 cm (2
1/2z) Cone type
Impedance/Input power (IEC)8≠/50 W§7 (Max)
Output sound pressure83 dB/W (1.0 m)
Frequency range105 Hz – 25 kHz (j16 dB)
160 Hz – 22 kHz (j10 dB)
Dimensions (WtHtD)106 mmk228 mmk131 mm
(4
3/16zk9zk53/16z)
MassApprox. 1.4 kg (3.1 lbs)
[Subwoofer\SB-HWX7]
Ty p e1 way, 1 speaker system (Bass reflex)
Wo of e r17 cm (6
3/4z) Cone type
Impedance/Input power (IEC)4≠/100 W§7 (Max)
Output sound pressure80 dB/W (1.0 m)
Frequency range32 Hz – 190 Hz (j16 dB)
39 Hz – 160 Hz (j10 dB)
Dimensions (WtHtD)137 mmk403 mmk437 mm
(5
13/32zk157/8zk177/32z)
MassApprox. 5.3 kg (11.7 lbs)
Optical digital outputOptical terminal (up to 96 kHz)
Optical digital inputOptical terminal (up to 48 kHz)Power supplyAC 120 V, 60 Hz
Power consumption90 W
Dimensions (WtHtD)360 mmk105.5 mmk334 mm
(1
43/16zk43/16zk135/32z)
Mass Approx. 4.7 kg(10.5 Ibs)
(Dimensions and Mass do not include the speakers.)
Operating temperature range
r5oC to r40oC (r41oF to r104oF)
Operating humidity range
10 % to 80 % RH (no condensation)
§7Rating with the low-cut filter equipped amplifier
[Note]
1. Specifications are subject to change without notice.
2. Total harmonic distortion is measured by a digital spectrum 
analyzer.
SPEAKER SECTION
DIGITAL AUDIO OUTPUT
DIGITAL AUDIO INPUT
GENERAL
Power consumption in standby mode
Power-Save Mode (Shipping condition)Approx. 0.5 W
Reference
Reference
PTX79P.book  Page 107  Monday, April 9, 2007  9:24 AM 
						

							RQT8926
108
Glossary
AAC (Advanced Audio Coding)
An audio compression method that compresses audio to 
approximately 1/12 of its size with CD-level quality. 
CPPM (Content Protection for Pre-recorded Media)
A copy protection system used for DVD-Audio files. This unit 
supports CPPM.
Decoder
A decoder restores the coded audio signals on DVDs to 
normal. This is called decoding.
DHCP (Dynamic Host Configuration Protocol)
Provides a mechanism for automatically assigning network 
information such as the IP address or Subnet mask sent by the 
router and so on to this unit.
DNS Server
A server which acts like a telephone directory and translates 
Internet domain names into IP addresses.
Dolby Digital
This is a method of coding digital signals developed by Dolby 
Laboratories. Apart from stereo (2-channel) audio, these 
signals can also be multi-channel audio. A large amount of 
audio information can be recorded on one disc using this 
method.
Down-mixing
This is a process of remixing the multi-channel audio (surround 
sound) on some discs into two channels. When you want to 
listen to the audio on a DVD with a 5.1 channel digital surround 
track through your television speakers, the down-mixed audio 
will be output.
Some DVD-Audio prevent down-mixing of all or part of their 
contents. When playing such discs, or such parts of the disc, 
unless the number of connected speakers is the same as the 
disc’s channel specification, audio will not be output properly.
DTS (Digital Theater Systems)
This surround system is used in many movie theaters around 
the world. There is good separation between the channels, so 
realistic sound effects are possible.
Dynamic range
Dynamic range is the difference between the lowest level of 
sound that can be heard above the noise of the equipment and 
the highest level of sound before distortion occurs.
Film and video
DVD-Videos are recorded using either film or video. This unit 
can determine which type has been used, then uses the most 
suitable method of progressive output.
Film: Recorded at 24 frames per second. (Recorded at 30 
frames per second as well). Generally appropriate for 
motion picture films.  
Video: Recorded at 30 frames/60 fields per second. Generally 
appropriate for TV drama programs or animation. Frame still and field still
Frames are the still pictures that go together to make a moving 
picture. There are about 30 frames shown each second.
One frame is made up of two fields. A regular television shows 
these fields one after the other to create frames.
A still is shown when you pause a moving picture. A frame still 
is made up of two alternating fields, so the picture may appear 
blurred, but overall quality is high.
A field still is not blurred, but it has only half the information of a 
frame still so picture quality is lower.
Gateway
IP address of the electronic device providing Internet access. 
Usually called a router IP address. (e.g., 192.168.0.1)
HDD (Hard disk drive)
This is a mass data storage device used in PC, etc. A disk with 
a surface that has been treated with magnetic fluid is spun and 
a magnetic head is brought in close proximity to facilitate the 
reading and writing of large amounts of data at high speed.
HDMI (High-Definition Multimedia Interface)
HDMI is a next-generation digital interface for consumer 
electronic products. Unlike conventional connections, it 
transmits uncompressed digital video and audio signals on a 
single cable. This unit supports high-definition video output 
(720p,1080i,1080p) from the HDMI AV OUT terminal. To enjoy 
high-definition video, a high-definition compatible television is 
required.
Hub
Used for connecting more than one device to the network.
IP address
A set of numbers which distinguish each PC on the network 
when, for example, connected to the Internet. When using a 
PC in a LAN (➜ below) to access a PC or device that is not 
included in the LAN, the IP address is called the local IP 
address. (e.g., 192.168.0.10)
JPEG (Joint Photographic Experts Group)
This is a system used for compressing/decoding color still 
pictures. If you select JPEG as the storage system on digital 
cameras, etc., the data will be compressed to 1/10–1/100 of its 
original size. The benefit of JPEG is less deterioration in 
picture quality considering the degree of compression.
LAN (Local Area Network)
A group of linked devices in a company, school or home. 
Indicates the boundaries of a particular network.
LPCM (Linear PCM)
These are uncompressed digital signals, similar to those found 
on CDs. 
MAC (Media Access Control) address
Address assigned to each device connected to the network to 
allow it to be recognized.
PTX79P.book  Page 108  Monday, April 9, 2007  9:24 AM 
						

							RQT8926
109
MP3 (MPEG Audio Layer 3)
An audio compression method that compresses audio to 
approximately 1/10 of its size without any considerable loss of 
audio quality.
Playback control (PBC)
If a Video CD has playback control, you can select scenes and 
information with menus.
Progressive/Interlace
NTSC, the video signal standard, has 480 interlaced (i) scan 
lines, whereas progressive scanning uses twice the number of 
scan lines. This is called 480p.
Using progressive output, you can enjoy the high-resolution 
video recorded on media such as DVD-Video.
Your television must be compatible to enjoy progressive video.
Router
Distinguishes the IP address assigned to each device, such as 
the PC, and relays the flow of data within the network.
Sampling frequency
Sampling is the process of converting the heights of sound 
wave (analog signal) samples taken at set periods into digits 
(digital encoding). Sampling frequency is the number of 
samples taken per second, so larger numbers mean more 
faithful reproduction of the original sound.
Subnet mask
Enables efficient network use. A set of numbers which identify 
which part of the IP address allocated to every device 
connected to the router is the network portion.TCP/IP (Transmission Control Protocol/Internet Protocol)
These are the standard protocols for sending and receiving 
data.
WMA (Windows Media
TM Audio)
WMA is a compression format developed by Microsoft 
Corporation. It achieves the same sound quality as MP3 with a 
file size that is smaller than that of MP3.
1080i (1125i)
In one high definition image, 1080 (1125) alternating scan lines 
pass every 1/60
th of a second to create an interlace image. 
Because 1080i (1125i) more than doubles current television 
broadcasts of 480i, the detail is much clearer and creates a 
more realistic and rich image.
1080p (1125p)
In one high definition image, 1080 (1125) scan lines pass at 
the same time every 1/60
th of a second to create a progressive 
image. Since progressive video does not alternate scan lines 
like interlace, there is a minimal amount of screen flicker. 
720p (750p)
In one high definition image, 720 (750) scan lines pass at the 
same time every 1/60
th of a second to create a progressive 
image. Since progressive video does not alternate scan lines 
like interlace, there is a minimal amount of screen flicker. 
1. Damage requiring service— The unit should be serviced by qualified service personnel if:
(a)The AC power supply cord or AC adaptor has been damaged; or
(b)Objects or liquids have gotten into the unit; or
(c)The unit has been exposed to rain; or
(d)The unit does not operate normally or exhibits a marked change in performance; or
(e)The unit has been dropped or the cabinet damaged.
2. Servicing— Do not attempt to service the unit beyond that described in these operating instructions. Refer all other servicing 
to authorized servicing personnel.
3. Replacement parts— When parts need replacing ensure the servicer uses parts specified by the manufacturer or parts that 
have the same characteristics as the original parts. Unauthorized substitutes may result in fire, electric shock, or other 
hazards.
4. Safety check— After repairs or service, ask the servicer to perform safety checks to confirm that the unit is in proper working 
condition.
The servicer will require all components to service your system. 
Therefore, should service ever be necessary, be sure to bring the entire system.
For product information or assistance with product operation:
In the U.S.A., refer to “Customer Services Directory” on page 110.
In Canada, contact the Panasonic Canada Inc. Customer Care Centre at 1-800-561-5505, or visit the website 
(www.panasonic.ca), or an authorized Servicentre closest to you.
Product Service
Product information
Reference
Reference
PTX79P.book  Page 109  Monday, April 9, 2007  9:24 AM 
						

							RQT8926
110
Limited Warranty (ONLY FOR U.S.A.)
Panasonic Consumer Electronics Company, 
Division of Panasonic Corporation of North America
One Panasonic Way Secaucus, New Jersey 07094
Panasonic Puerto Rico, Inc.Ave. 65 de Infantería, Km. 9.5 
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Panasonic Audio Products Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or 
workmanship, Panasonic Consumer Electronics Company or Panasonic Puerto 
Rico, Inc. (collectively referred to as “the warrantor”) will, for the length of the period 
indicated on the chart below, which starts with the date of original purchase 
(“warranty period”), at its option either (a) repair your product with new or 
refurbished parts, or (b) replace it with a new or a refurbished product. The decision 
to repair or replace will be made by the warrantor.
During the “Labor” warranty period there will be no charge for labor. During the 
“Parts” warranty period, there will be no charge for parts. You must carry-in or mail-
in your product during the warranty period. If non-rechargeable batteries are 
included, they are not warranted. This warranty only applies to products purchased 
and serviced in the United States or Puerto Rico. This warranty is extended only to 
the original purchaser of a new product which was not sold “as is”. A purchase 
receipt or other proof of the original purchase date is required for warranty service.Carry-In or Mail-In Service
For Carry-In or Mail-In Service in the United States call 1-800-211-PANA (1-800-
211-7262) or visit Panasonic web site: http://www.panasonic.com
For assistance in Puerto Rico call Panasonic Puerto Rico, Inc. (787)-750-4300 or 
fax (787)-768-2910. 
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, 
and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty 
ALSO DOES NOT COVER damages which occurred in shipment, or failures which 
are caused by products not supplied by the warrantor, or failures which result from 
accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty 
installation, set-up adjustments, misadjustment of consumer controls, improper 
maintenance, power line surge, lightning damage, modification, or commercial use 
(such as in a hotel, office, restaurant, or other business), rental use of the product, 
service by anyone other than a Factory Servicenter or other Authorized Servicer, or 
damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER 
“LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR 
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE 
OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. 
(As examples, this excludes damages for lost time, travel to and from the servicer, 
loss of media or images, data or other memory content. The items listed are not 
exclusive, but are for illustration only.) ALL EXPRESS AND IMPLIED 
WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE 
LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential 
damages, or limitations on how long an implied warranty lasts, so the exclusions 
may not apply to you. This warranty gives you specific legal rights and you may also 
have other rights which vary from state to state. If a problem with this product 
develops during or after the warranty period, you may contact your dealer or 
Servicenter. If the problem is not handled to your satisfaction, then write to the 
warrantor’s Consumer Affairs Department at the addresses listed for the warrantor.
PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED 
WARRANTY ARE YOUR RESPONSIBILITY.
F1206
Product or Part Name Parts Labor
Audio Products (except items listed 
below)One (1) year  One (1) year
USB Reader-Writer, Personal Computer 
Card Adapters (in exchange for defective 
item)One (1) yearNot 
Applicable
Accessories: Headphones, Cartridges, 
Microphones, AdaptersNinety (90) 
daysNinety (90) 
days
Rechargeable Batteries, DVD-R/-RAM 
Discs (in exchange for defective item)Ten (10) 
daysNot 
Applicable
SD Memory Cards, Rechargeable Battery 
Packs (in exchange for defective item)Ninety (90) 
daysNot 
Applicable
Customer Services Directory
Obtain Product Information and Operating Assistance; locate your nearest Dealer or Servicenter; purchase Parts 
and Accessories; or make Customer Service and Literature requests by visiting our Web Site at:
http://www.panasonic.com/consumersupport
or, contact us via the web at:
http://www.panasonic.com/contactinfo
You may also contact us directly at:
1-800-211-PANA (7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.
For hearing or speech impaired TTY users, TTY : 1-877-833-8855
Accessory Purchases
Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at:
http://www.pstc.panasonic.com
or, send your request by E-mail to:
[email protected]
You may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday – Friday 9 am to 8 pm, EST.)
Panasonic Service and Technology Company
20421 84th Avenue South, Kent, WA 98032
(We Accept Visa, MasterCard, Discover Card, American Express, and Personal Checks)
For hearing or speech impaired TTY users, TTY : 1-866-605-1277
Service in Puerto Rico
Panasonic Puerto Rico, Inc.
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phone (787)750-4300, Fax (787)768-2910
PTX79P.book  Page 110  Monday, April 9, 2007  9:24 AM