Panasonic Dvd Home Theater Sound System Sc Pt770 Operating Instructions

							11
RQTX0221
Getting Started
Quick Start Guide
Conserving power
The main unit and the wireless system consume a small amount of 
power when they are turned off (\U.S.A.[ and\Canada] main unit: approx. 
0.1 W, wireless system: approx. 0.2 W, \Others] main unit: approx. 0.2 W, 
wireless system: approx. 0.3 W). To save power when they are not to be 
used for a long time, unplug them from the household AC outlet.
You will need to reset some memory items after plugging in the main 
unit.[Note]
The included AC power supply cords are for use with the main unit and 
wireless system only. Do not use them with other equipment. Also, do 
not use cords for other equipment with the main unit or wireless system.
Turn on the wireless system after all connections are complete.
≥Use alkaline or manganese batteries.
≥Do not heat or expose to flame.
≥Do not leave the battery(ies) in an automobile exposed to direct 
sunlight for a long period of time with doors and windows closed.
Do not:≥mix old and new batteries.
≥use different types of batteries at the same time.
≥take apart or short circuit.
≥attempt to recharge alkaline or manganese batteries.
≥use batteries if the covering has been peeled off.
Mishandling of batteries can cause electrolyte leakage which can 
severely damage the remote control.
Remove the batteries if the remote control is not going to be used for a 
long period of time. Store in a cool, dark place.
Aim at the remote control signal sensor (B39), avoiding obstacles, at a 
maximum range of 7 m (23 ft) directly in front of the unit.
step 4AC power supply cord connections
AC INAC IN11 0 127V220 240V
VOLT ADJ
To  
household 
AC outletMain unit Wireless system
AC power supply cord
(included)
Before connecting the AC power 
supply cord
Set the voltage.
Use a flat-head screwdriver to move the 
voltage selector to the appropriate position 
for the area in which this system is used.
Ferrite core≥If the AC plug does not fit 
your household AC outlet
Use the AC plug adaptor 
(included).
If it still does not fit, contact an electrical 
parts distributor for assistance.
AC power 
supply cord
(included)To  
household 
AC outlet [For\areas\except\U.S.A.[and\Canada]
step 5Preparing the wireless system
WIRELESS LINKPOWER
WIRELESS LINK indicator
Red:The wireless system is on and the wireless link is deactivated.
Green:The wireless system is on and the wireless link is activated.
(“ [W1] ” is also displayed on the main unit’s display.)
Press [POWER CI, BÍ] on the wireless system.
Unit on/off button [POWER CI, BÍ]
Use this button to turn the wireless system on and off.
CI:  The wireless system is on.
BÍ: The wireless system is off.
Wireless system
step 6Preparing the remote control
Batteries
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only 
with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
R6/LR6, AA
Insert so the poles ( and ) match those in the remote control.
Press in and lift up.
Replace the cover.
Use
RQTX0221-P_770_en.book  Page 11  Monday, January 12, 2009  5:56 PM 
						

							12
RQTX0221
Quick Start Guide
Getting Started
The Smart setup screen assists you in making necessary 
settings.
≥Language
Select the language used on menu screen.≥TV aspectSelect the aspect to suit your TV.≥Speaker checkListen to speaker output to confirm speaker connections.≥Auto speaker setupAdjust the speaker output level automatically. (Bbelow)≥Speaker outputMake surround sound setting for speaker output.≥TV audioSelect the audio input connection from your TV.
For AUX connection (B9): Select “AUX”.
For OPTICAL IN connection (B9): Select “DIGITAL IN”.
This will be the TV audio setting for VIERA Link “HDAVI Control”. (B24)
[Note]
≥If this unit is connected to a “HDAVI Control 3 or later” compatible TV 
via HDMI cable, the menu language and TV aspect information will be 
retrieved via VIERA Link.
≥If this unit is connected to a “HDAVI Control 2” compatible TV via 
HDMI cable, the menu language information will be retrieved via 
VIERA Link.
≥Settings in the Smart setup can also be changed in the player settings 
[e.g. language, TV aspect, speaker level and TV audio (B28)].
∫Adjusting the speaker output level automatically: 
Auto speaker setup
The speaker level settings can be optimized to accommodate your 
room’s listening conditions so that you can enjoy the ideal surround 
sound experience.
≥Place the Auto speaker setup microphone at actual seating position. 
(At ear level when seated.)
≥The test signal is output from each speaker.
[Note]
Auto speaker setup can be activated through Smart setup only.
step 7SMART SETUP
Preparation
Turn on your TV and select the appropriate 
video input mode (e.g. VIDEO 1, AV 1, HDMI, 
etc.) to suit the connections to this unit.
≥To change your TV’s video input mode, refer 
to its operating instructions.
≥This remote control can perform some basic 
TV operations (B38).
1Turn on the unit.
≥When the Smart setup screen appears 
automatically, skip step 2 and 3.
2Select “DVD/CD”.
3Show the Smart setup.e.g.
4Select “Yes”.
5Follow the messages and 
make the settings.
(Bright, Smart setup settings)
6Finish Smart setup.
OK
DVD
OK
DVD
SMART SETUP
DVD
SMART SETUP
(Main unit only)
SET
RETURN
Smart setupWould you like to start smart
setup?
Ye s
No
OK
OK
OK
Smart setup settings
Keep as quiet as possible during the Auto speaker setup. Loud 
voices, air-conditioning noise, or excessive wind may lead to incorrect 
settings. The speakers output loud test signals during setup.
SETUP MIC
RQTX0221-P_770_en.book  Page 12  Monday, January 12, 2009  5:56 PM 
						

							13
RQTX0221
Getting Started Playing Discs Other Operations Reference
Setting up the radio
Up to 30 stations can be set in each band, FM and AM.
≥“SET OK” is displayed when the stations are set, and the radio tunes to 
the last preset station.
≥“ERROR” is displayed when automatic presetting is unsuccessful. 
Preset the channels manually (B14).≥The FM/AM setting is also shown on the TV display.
When “FM” is selected
Press and hold the button again to cancel the mode.
≥The mode is also canceled when you change the frequency.
When “AM” is selected
Press [FUNCTIONS] on the remote control.Each time you press the button: BP 2 ,# BP 1
(Continued on next page)
Presetting stations automatically
1Select “FM” or “AM”.≥Main unit:
Press [SELECTOR].
2Each time you press the button:
LOWEST (factory preset):
To begin auto preset with the lowest 
frequency.
CURRENT:
To begin auto preset with the current 
frequency.
§
§
 To change the frequency, refer to “Manual 
tuning” (Bright).
3
(press and hold)Release the button when 
“FM AUTO” or “AM AUTO” is displayed.
≥Main unit:
Press and hold [MEMORY].
The tuner starts to preset all the stations it 
can receive into the channels in ascending 
order.
PLAY
MODE
123
456
78
0
9
10
SEARCHSEARCH
EXT-INRADIO
FUNCTIONS
MENU
OK
SKIPSKIP
,SEARCH
Numbered
buttons
FUNCTIONS
RADIO
OK PLAY MODE
MENU
,
VOLUME
SELECTORTUNE
MEMORY-TUNE MODE/—FM MODE
EXT-INRADIO
MENU
PLAY
LIST
OK
Confirming the preset channels
1Select “FM” or “AM”.≥Main unit:
Press [SELECTOR].
2Select the channel.
≥To select a 2-digit number
e.g. 12: [S10] B [1] B [2]
Alternatively, press [X,W].
≥Main unit:
Press [-TUNE MODE] to select “PRESET” 
on the display, and then press 
[XTUNEW] to select the channel.
When a stereo FM broadcast is being 
received, “ST” lights in the display.
If noise is excessive
Press and hold [PLAY MODE] 
(main unit: [—FM MODE]) to 
display “MONO”.
Manual tuning
1Select “FM” or “AM”.≥Main unit:
Press [SELECTOR].
2Select the frequency.
≥Main unit:
Press [-TUNE MODE] to select “MANUAL” 
on the display, and then press 
[XTUNEW] to select the frequency.
≥To start automatic tuning, press and hold 
[6, 5] (main unit: [XTUNEW]) until 
the frequency starts scrolling. Tuning 
stops when a station is found.
EXT-INRADIO
123
456
78
0
9
10
ST
MONO
EXT-INRADIO
SEARCHSEARCH
RQTX0221-P_770_en.book  Page 13  Monday, January 12, 2009  5:56 PM 
						

							14
RQTX0221
Getting Started Playing Discs Other Operations Reference
Setting up the radio (continued)
Up to 30 stations can be set in each band, FM and AM.
A station previously stored is overwritten when another station is stored in 
the same channel preset.
FM frequency step
Main unit only
The step is factory-set to 0.2-MHz, but you can change it to receive 
broadcasts allocated in 0.1-MHz steps. You may need to change this 
setting if the tuner seems to skip over the correct frequency for stations in 
your area.
1Press [SELECTOR] to select “FM”.
2Press and hold [SELECTOR].
After a few seconds the display changes to show the current minimum 
frequency. Continue to hold the button down. The minimum frequency 
changes and the step is changed.
e.g. 87.9 (Factory preset) ,# 87.5
To return to the original step, repeat steps 1 and 2.
[Note]
After changing the setting, previously preset frequencies will be cleared. 
Preset them again.
123
456
78
0
9
10
OK
SKIPSKIP
Numbered
buttons
OK
,
VOLUME
SELECTORTUNE
MEMORY
Presetting stations manually
1While listening to the radio broadcast
Press [OK].
2While the frequency is flashing on the display
Press the numbered buttons to select a channel.
≥To select a 2-digit number
e.g. 12: [S10] B [1] B [2]
Alternatively, press [X,W], and then press [OK].
Main unit:
1While listening to the radio broadcast
Press [MEMORY] twice.
2While a channel number is flashing on the display
Press [XTUNEW], and then press [MEMORY].
RQTX0221-P_770_en.book  Page 14  Monday, January 12, 2009  5:56 PM 
						

							15
RQTX0221
Getting Started Playing Discs Other Operations Reference
Selecting the playback source
You can select desired source or access playback/menus by using the 
START menu.
When “Input select” is selectedYou can select a desired source from the menu.
≥DVD/CD (B12), FM (B13), AM (B13), AUX§ (Bright), 
DIGITAL IN§ (Bright), iPod (B26)§“(TV)” will appear beside “AUX” or “DIGITAL IN”, indicating the TV 
audio setting for VIERA Link “HDAVI Control” (B24).
When a disc is loaded, you can also access playback or menus from the 
START menu.
e.g. [DVD-V]
When the on-screen control panel appears
e.g. [DVD-V] (when “Playback Disc” is selected from the START menu)
You can operate the playback with the indicated controls.Press [SELECTOR] on the main unit to select source from the main unit. 
(B39)
[Note]
Confirm the audio connection to the AUX or OPTICAL IN terminal on the 
main unit when you select the corresponding sources (B9). Reduce the 
volume on the TV to its minimum and then balance the TV volume with 
the volume setting on the main unit. Refer also to the operating 
instructions for your TV to balance the sound.
Select to suit the type of audio from the OPTICAL IN terminal on the main 
unit.
(When receiving true 5.1-channel surround sound, select “PCM OFF”.)
[Note]
≥Audio that is input through the OPTICAL IN terminal is not output from 
the HDMI terminal.
≥Underlined items in the above paragraph are factory settings.
Selecting the source from the START menu
1Show the START menu.This unit automatically turns on.
(The TV also turns on when using VIERA 
Link “HDAVI Control”. This works only when 
in “DVD/CD” or “IPOD” mode without any 
disc/device being loaded/connected.)
e.g.
2Select an item.≥To exit, press [START].
3Make the setting.
DVDiPod
START
SETUP
EXT-INRADIO
OK
RADIO, EXT-IN DVD
iPod
SETUPSTART
OK
START
DVD/CD Home theater
OK
RETURN
Input select
OK
OK
DVD/CD Home theater
OK
RETURN
Input select Playback Disc
TOP  MENU (DVD)
MENU (DVD)
Playback/menu access
Selecting the source by the remote control
DVD/CD (B12)
Each time you press the button:
FM (B13)
AM (B13)
AUX
§: For audio input through the AUX 
terminal.
D-IN
§: For audio input through the 
OPTICAL IN terminal. (Bbelow)
§“(TV)” will appear beside “AUX” or “D-IN”, 
indicating the TV audio setting for VIERA 
Link “HDAVI Control” (B24).
iPod (B26)
Making settings for digital audio input
1 While in “D-IN” mode
Press [SETUP] to select “MAIN/SAP”, “DRC” or “PCM FIX”.
2 While the selected mode is displayed
Press [3,4] to make the setting.
MAIN/SAP mode (Only works with Dolby Dual Mono):
MAIN, SAP
§, MAIN+SAP§ (stereo audio)§“SAP” = Secondary Audio Program
Dynamic Range Compression
DRC ON:Adjust for clarity even when the volume is low by 
compressing the range of the lowest sound level and the 
highest sound level. Convenient for late night viewing. 
(Only works with Dolby Digital)
DRC OFF
:The full dynamic range of the signal is reproduced.
PCM FIX mode
PCM ON:Select when receiving only PCM signals.
PCM OFF
:Select when receiving Dolby Digital and PCM signals.
DVD
EXT-INRADIO
iPod
RQTX0221-P_770_en.book  Page 15  Monday, January 12, 2009  5:56 PM 
						

							16
RQTX0221
Getting Started Playing Discs Other Operations Reference
≥The following sound effects may not be available or may have no effect 
with some sources, or when headphones are used (B39).
≥You may experience a reduction in sound quality when these sound 
effects are used with some sources. If this occurs, turn the sound effects 
off.
§“ÎPLII” lights in the main unit’s display when there is effect.You can enhance the surround effect for low volume 5.1-channel sound.
(Convenient for late night viewing.)
Enjoying sound from all speakers and various 
sound effects
Enjoying surround sound effects
SURROUND OUTPUT indicator on the main 
unit will light up when there is surround 
sound effect.
Each time you press the button:
STANDARD:
Sound is output as it was recorded/encoded.
Speaker output varies depending on the 
source.
MULTI–CH:
You can enjoy sound from the front 
speakers, as well as the surround speakers 
even when playing a 2-channel sound or 
non-surround sound.
MANUAL: (Bbelow)
While “MANUAL” is 
displayedSelect other surround modes.
Each time you press [2,1]:
PLII MOVIE §
Suitable for movie software, or softwares 
recorded in Dolby Surround.
PLII MUSIC
 §
Adds 5.1-channel effects to stereo 
sources.
S.SRND
You can enjoy sound from all speakers 
with stereo sources. (Surround output will 
be in mono.)
STEREO
Sound will only be output to the front 
speakers and the subwoofer from any 
source.
VOL
SOUNDSURROUND
-CH SELECTSETUPW.SRD
OKOK
+,    VOL
SETUP,
─ CH SELECTSURROUNDSOUND
W.SRD
SURROUND
Recommended modes to enjoy TV audio or stereo 
sources from all speakers:
≥PLII MOVIE
≥PLII MUSIC
≥S.SRND
Selecting sound mode
1Select a sound mode.
Each time you press the button:
EQ: Equalizer
SUBW LVL: Subwoofer Level
C.FOCUS: Center Focus
2While the selected 
mode is displayedMake settings.Refer to the following for setting details of 
each sound effect.
Equalizer
You can select sound quality settings.
Each time you press [2,1]:
HEAVY:Adds punch to rock.
CLEAR:Clarifies higher sounds.
SOFT:For background music.
FLAT:Cancel (no effect is added).
Subwoofer level
You can adjust the amount of bass. The unit automatically 
selects the most suitable setting according to the type of 
playback source.
SUB W 1 ,# SUB W 2 ,# SUB W 3 ,# SUB W 4^-------------------------------------------------------------------J
≥The setting you make is retained and recalled every time you 
play the same type of source.
Center Focus
(Effective when playing audio containing center channel 
sound or when “ÎPLII” lights in the main unit display.)
You can make the sound of the center speaker seem like it is 
coming from within the TV.
C.FOCUS ON,------.C.FOCUS OFF
Whisper-mode Surround
≥“(( ))” lights when there is effect.
Each time you press the button:
WHISPER-MODE SRD ON

WHISPER-MODE SRD OFF
SOUND
W.SRD
RQTX0221-P_770_en.book  Page 16  Monday, January 12, 2009  5:56 PM 
						

							17
RQTX0221
Getting Started Playing Discs Other Operations Reference
Preparation
≥To display the picture, turn on the TV and select the appropriate video 
input mode.
≥Press [i,`VOL] to adjust the volume to normal listening level.
≥Select “TEST TONE” from “SPEAKER SETTINGS” in AUDIO menu 
(B29).
(Effective when playing 5.1-channel sound or when “ÎPLII” lights.)
Adjusting the speaker output level manually
1Enter test tone mode.
Test tone will be output to each channel in 
the following order.
LEFT, CENTER, RIGHT,
SURROUND RIGHT, SURROUND LEFT
2Adjust the speaker level for each 
speaker. (CENTER, SURROUND 
RIGHT, SURROUND LEFT)
`6dB to i6 dB (Factory preset: 0 dB)
≥To exit the screen, press [SETUP].
To adjust speaker level during play
1Press and hold [—CH SELECT] to select the speaker.
While the speaker channel is displayed, press [—CH SELECT].
L# C# R# RS# LS# SW
^----------------------------------------------}
≥You can adjust SW (Subwoofer) only if the disc includes a 
subwoofer channel and “ÎPLII” is not lit.
≥“S” appears on the main unit’s display when you have selected 
“S.SRND” (B16, Enjoying surround sound effects). In this case, 
you can adjust both surround speaker levels at the same time using 
[3,4].
S: `6dB to i6dB
2Press [3] (increase) or [4] (decrease) to adjust the speaker level 
for each speaker.
C, RS, LS, SW: `6dB to i6dB
(L, R: Only the balance is adjustable.)
To adjust the balance of the front speakers, while “L” or “R” is selected, 
press [2,1].
OKe.g.
SET
RETURN
AUDIO-SPEAKER SETTINGS-TEST TONESPEAKER
LEFT
CENTER
RIGHT
SURROUND RIGHT
SURROUND LEFTTRIM LEVEL
−  −
0dB
−  −
0dB
0dB
EXIT : SETUP
OK
RQTX0221-P_770_en.book  Page 17  Monday, January 12, 2009  5:56 PM 
						

							18
RQTX0221
Getting Started Playing Discs Other Operations Reference
Play in g D is cs
Basic play
Preparation
To display the picture, turn on your TV and change its video input mode (e.g. VIDEO 1, AV 1, HDMI, etc.) to suit the connections to this unit.
[Note]
≥DISC CONTINUES TO ROTATE WHILE MENUS ARE DISPLAYED.
To preserve the unit’s motor and your TV screen, press [∫] (Stop) when you are finished with the menus.
≥Total title number may not be displayed properly on iR/iRW. If you are experiencing problems, refer to troubleshooting (B32 to 33)
Using the main unit
Pull open
VOLUME
TUNESELECTOREXCHANGE123455 DISC SELECTOR
123455 DISC SELECTOR
4
, +  VOLUMEEXCHANGE
12SELECTOR
3
TUNE
(Stop)
POWER
MEMORY
5OPEN CLOSE
Load the disc.≥Load double-sided discs so the 
label for the side you want to play is 
facing up.
≥Press [EXCHANGE] to load discs 
one by one.
≥For DVD-RAM, remove the disc 
from its cartridge before use.
≥Do not:
– Load more than one disc per tray.
– Push or pull out the tray by hand.Label 
facing up
Start play.
≥Turn [`, i VOLUME] to 
adjust the volume.
Select “DVD/CD”. Turn on the unit.
Press to skip.
Press and hold to:
– search during play
– start slow-motion play during pause
≥Press [1] (Play) to start normal play.
Open all the disc trays.≥To select a desired tray (Bbelow, Selecting the desired tray).
≥Press [
						

							19
RQTX0221
Getting Started Playing Discs Other Operations Reference
Using the remote control
One touch 
play
(during standby 
mode)
(Remote control only)
The main unit automatically turns 
on and starts playing the disc in 
the tray.
StopThe position is memorized while 
“RESUME STOP” is on the 
screen.
≥Press [1PLAY] to resume.
≥Press [∫STOP] again to clear 
the position.
Pause≥Press [1PLAY] to restart play.
Skip
Search(during play)
≥Up to 5 steps.
≥Press [1PLAY] to start normal 
play.
Slow-motion(during pause)≥[VCD] Slow-motion: Forward 
direction only.
Frame-by-
frame
(during pause)
[DVD-VR] [DVD-V] [VCD]
≥[DVD-VR] [VCD] Forward direction 
only.
On-screen 
item select
RETURN
VOL
STOP
123
456
78
0
9
DISC
SEARCH
SKIPSLOWSKIP
PLAY
PA U S E
SEARCH
OK
DVD
 TOP MENU
10
PLAYLISTMENU
FL DISPLAY
DIRECT NAVIGATOR
1
25
SLOW, SEARCH,,SKIP
PAUSE
STOP
OK
RETURN
DISC
MENU, PLAY LIST
FL DISPLAY
TOP MENU,
DIRECT NAVIGATOR
Numbered
buttons+,    VOL
PLAY
STOP
PAUSE
SKIPSKIP—
SEARCH
SLOW
SEARCH
OK
OK
Select
Confirm
—
Selecting a 
discDisc information screen is 
displayed.
≥To exit the screen, press [DISC].
e.g. [DVD-V]
Enter 
number[DVD-VR] [DVD-V] [VCD] [CD]
e.g. To select 12:
[S10] B [1] B [2]
[VCD] with playback control
Press [∫STOP] to cancel the PBC 
function, and then press the 
numbered buttons.
Disc menu[DVD-V]
Shows a disc top menu.
[DVD-VR]
Press the button to show the 
programs (B21).
[DVD-V]
Shows a disc menu.
[DVD-VR]
Press the button to show a play list 
(B21).
[VCD] with playback control
Shows a disc menu.
Return to 
previous 
screen
Main unit 
display[DVD-VR] [DVD-V] [WMA] [MP3]
Tim e d is play
,-. Information display
(e.g. [DVD-VR] Program 
number)
[JPEG]
SLIDE
,-.Contents number
OK
Select
Confirm
or
123
45
DISC
DISC CHANGE
CD
DVD-VR
UNCHECKED
NO DISC DVD-VIDEO 12345
Empty tray Not yet read
123
456
78
0
9
10
 TOP MENU
DIRECT NAVIGATOR
PLAYLIST
MENU
RETURN
RETURN—
-SLEEP
FL DISPLAY
RQTX0221-P_770_en.book  Page 19  Monday, January 12, 2009  5:56 PM 
						

							20
RQTX0221
Getting Started Playing Discs Other Operations Reference
Other modes of play
This feature allows you to play all loaded CDs sequentially. Select an 
applicable disc before playing (B19, Selecting a disc).
≥If all loaded discs are DVDs, CD Mode does not work.
≥Video CD playback control is disabled.
≥You cannot turn CD Mode on or off during program or random mode.
≥If you want to play a DVD, press and hold [—CD MODE] again while 
stopped to cancel CD Mode. (CD Mode is also canceled when you 
switch the unit to standby, select another source, or when the disc tray 
is opened.)
This works only when the elapsed play time can be displayed. It also 
works with all JPEG content.
Items shown differ depending on the type of disc and playback mode.
To enjoy program or random play with:
– 1 disc : ensure CD Mode (Babove) is off
– all discs : ensure CD Mode is on
Preparation
≥[DVD-VR] Select “DATA” in “DVD-VR/DATA” (B29, OTHERS menu) to 
play WMA, MP3, JPEG contents.
≥[DVD-V] Some items cannot be played even if you have programmed 
them.
∫1-Disc program[DVD-V] [VCD] [CD] [WMA] [MP3] [JPEG] You can program all the items on a 
disc in the selected tray.
∫All-Disc program (when CD Mode is on)[VCD] [CD] You can program all the items on all the discs.
To select all the items
Press [3,4] to select “ALL” and press [OK].
To clear the selected program
1 Press [1] and then press [3,4] to select the program.
2 Press [CANCEL].
To clear the whole program
Press [1] several times to select “CLEAR ALL”, and then press [OK].
The whole program is also cleared when the disc tray is opened, the unit 
is turned off or another source is selected.
∫1-Disc random[VCD] [CD] You can playback all the items on a disc in the selected tray in 
random order.
[DVD-V] [WMA] [MP3] [JPEG] You can playback selected item(s) on a disc in 
the selected tray in random order.
∫All-Disc random (when CD Mode is on)[VCD] [CD] You can playback all the items on all the discs in random order.
Playing CDs sequentially (CD Mode)[VCD] [CD] [WMA] [MP3]
While stopped
(press and hold)
Repeat play
1During play
(press and hold)Show the repeat mode.
2While the repeat 
mode is displayedSelect an item to be repeated.
e.g. [DVD-V]
`TITLE ---. `CHAP. ---. `OFF
^----------------------------------------------------b
To cancel, select “OFF”.
Program and Random play[DVD-V] [VCD] [CD] [WMA] [MP3] [JPEG]
While stoppedSelect the play mode.Program and random playback screens appear 
sequentially.
Program ------------------------------------------) Random
^--- Exit program and random screens (}
PLAY
-CD MODE
PLAY
MODE-REPEAT
OK
RETURN
CANCEL
OK
RETURN
CANCEL
PLAY
─ CD MODE
PLAY MODE,
─ REPEAT
DISC
-CD MODEPLAY
W1W2CDP.MODE
PLAY
MODE
-REPEAT
PLAY
MODE
-REPEAT
PLAY
MODE
-REPEAT
Program play (up to 30 items)
1Select an item.e.g. [DVD-V]
≥Repeat this step to program other items.
≥To return to the previous menu, press 
[RETURN].
2Start play.
1Press [3,4], and then press [OK] to select the disc.
2Press [3,4], and then press [OK] to select the track.
3Repeat step 1 and 2 to program other items.
≥To return to the previous menu, press [RETURN].
4Press [1PLAY].
Random play
1(Only when the disc has groups or multiple 
titles.)
Select a group or title.e.g. [DVD-V]
≥“¢” represents selected. To deselect, press 
[OK] again.
2Start play.
Press [1PLAY].e.g. [CD]
OKDVD-V  PROGRAMSELECT TITLETITLE CHAPTER
TITLE  1
TITLE  2
TITLE  3
TITLE  41
2
3
4
5
6
7
8
9
10
START:PLAY
CLEAR ALL
PLAY
OK
DVD-V  RANDOM
SELECT  TITLE
TITLE  1
TITLE  2
TITLE  3
PRESS PLAY TO START
PLAY
ALL DISC RANDOM
PRESS PLAY TO START
RQTX0221-P_770_en.book  Page 20  Monday, January 12, 2009  5:56 PM