Panasonic Dmr Hs2 Operating Instructions Manual

							Editing
41
RQT6570
The program is erased.
[Note]≥ The disc’s available recording time may not increase after 
erasing short programs.
≥ Computer data cannot be erased.
≥ The available recording time on DVD-R does not increase when 
you erase programs.
Press [2] to set (or 
cancel) protection 
and press [ENTER].
≥ Use search and slow-motion to find the start and end points. 
≥ Play pauses if the end of the program is reached during this procedure.
≥ You may not be able to specify points within 3 seconds of each other.
≥ You cannot specify an end point before a start point, or a start point after an end 
point. 
≥ You cannot specify points on still pictures in the program.
≥ The disc’s available recording time may not increase after erasing short segments.
Repeat to enter other sections.
Press [3, 4] to 
select “Exit”  and 
press [ENTER]. 
Press [2] to 
select “Erase” 
and press 
[ENTER]. 
Press [ENTER] at the 
point you want to 
divide the program.
To change the division point 
➜ below
Press [3, 4] to select “Next” and press [ENTER], then press [2] to 
select “Erase” and press [ENTER].
Press [2] to select 
“Divide” and press 
[ENTER].
0:19    Remaining Recording Time
Shorten Segment
Corresponding PLAY LIST will also be erased.
Erase Cancel
RETURN
ENTERSELECT
Divide Program
Divide Cancel
RETURN
ENTERSELECT
The program is divided.
[Note]≥ Cancel Disc Protection (➜ page 38) or Cartridge Protection (➜ page 8) if 
they are currently set. [RAM]
≥ The full title is shown in the Properties screen, but if you enter a long title, 
only part of it is shown in the program list.
≥ If you enter a long title, only part of it is shown in the menu screen after 
finalization. [DVD-R]
Once you divide the program,  
it will not be restored to the original.
Press [2] to 
select “Erase”  and 
press [ENTER].
Press [ENTER] at 
the start point of 
the section you 
want to erase.Press [ENTER] at 
the end point of the 
section you want to 
erase.
Press [3, 4] to 
select “Exit” 
and press 
[ENTER].
To confirm the division pointPress [3, 4] to select “Preview” and press [ENTER].
(Play will begin from a point 10 seconds prior to and 
after the division point.)
To change the division pointPress [3, 4] to select “Divide” and press [ENTER] 
at the point you want to change.
[Note]≥ The divided programs retain the title of the original program. They also retain 
the CPRM property (➜ page 8) of the original.
≥ A minute portion of the recording directly preceding the division point may be lost.
≥ It is not possible to carry out Divide Program in the following cases:
– when the program is extremely short.
– when the total number of programs is more than 250 (HDD) or 99 (DVD-RAM).
DIRECT NAVIGATOR
3
3
ENTER0   ~   9No TOTAL 3SELECTRETURN
DVDNo DATECH TIME EDITTITLE
  9 : 00 PMAuto action026/20 WED61
1
1
1
1
11 : 00 PMUSJ036/20 WED13 01
6/20 WED410 : 00 AMDinosaurThe lock symbol 
appears when the 
program is write-
protected.
Shorten
     Segment
0 : 00 . 01Start– : – – . – –End3
StartEndNextExit
0 : 00 . 01
PLAY03
RETURN ENTERSELECT
N
S
DVD
0 : 00 . 01StartEnd3
StartEndNextExit
0 : 10 . 15
RETURN ENTERSELECT
0 : 10 . 15
03
3
Shorten
     Segment
N
S
DVD 
						

							Editing
42
RQT6570
Editing play lists
Properties
No.
Scenes 0:05.51Date
Total 1
00410/23/2001           
RETURN
ENTER
Dinosaur
Erase this PLAY LIST?
EraseErase PLAY LIST
Cancel
RETURN
ENTERSELECT
Copy this PLAY LIST?
CopyCopy PLAY LIST
Cancel
RETURN
ENTERSELECT
PLAY LIST
Edit Scenes
0   ~   9Select Page
001 / 001
  1 10/23 0:03 004 Dinosaur
 Prev. Next
AddMoveRe-editErase
RETURN ENTERSELECT---------
---
002003
004--- 001 00:00.19
ENTER
_Enter Title
1 1
2
3
4
5
6
7
8
9
0
1002345
ABC a
DE F d
GH I
NOg
JKL j
M
m
67890
bcij
ef /l%
hifl$¢
&
klON@
n]_o[
SPACE
SETERASE
SELECT
0100PQRS p
TUV t
WX Y Z wqrs ( )
uv { }-
xyz
`^| 
! ?\
.
,

:
; ––
RETURN
π;
PLAY LIST
------NoDATE TOTALSCENEEDIT TITLE
USJ006 02 10/26 0:073
3
1
1
1
1
1
1
002003
004
001
--- ----/----:--
0   ~   9No
RETURN ENTERSELECT03 10/21 0040:06
Dinosaur
Auto action01 10/23 0040:03
CH
VOLUME
123
789
0
10 0
4
56
SLOW/SEARCH
DIRECT NAVIGATOR
TOP
MENUMENU
RETURNFUNCTIONSPROG/CHECKDISPLAYTIME SLIPADD/DLT
ENTER
PLAY LIST
CANCEL
HDDDVD
3, 4, 2, 1
ENTER
RETURN
PLAY LIST Numbered
buttons
HDD, DVD
DVD
DVD
Play Scenes
Operation
While stopped
Press [PLAY LIST].
Press [3, 4] to select the 
list.
≥ To create a new list, select  
“` `” and press [ENTER]  
(➜ page 44). 
Press [1] so the 
submenu appears.
To clear the play list or scene list 
screen
Press [RETURN].
To stop set up processPress [RETURN].
≥ You can also use [3, 4, 2, 1] to 
select “Cancel” or “No” and press 
[ENTER].
For your reference
You can only access “Play Scenes” and 
“Properties” if Disc Protection (➜ page 
38) or Cartridge Protection (➜ page 8) 
is activated. Deactivate the protection to 
access other items. [RAM]You can enter up to 64 characters.
The full title is shown in the 
Properties screen, but if you enter a 
long title, only part of it is shown in 
the play list screen.
Play list information (e.g., time and 
date) is shown.
Edit Scenes
Press [2, 1] to select the 
item (Add, Move, Re-edit 
or Erase) and press 
[ENTER].
Press [3, 4] to select the 
item and press [ENTER].
≥ Press [
3, 
4, 
2, 
1] to select “Next” and press [ENTER] to show 
scene 10 and later.
≥ You can also select a page of scenes  by entering a 3-digit number 
with the numbered buttons. 
e.g.: “5”:  [0] ➜ [0] ➜ [5]
   “15”: [0] ➜ [1] ➜ [5]
≥ HDD or one disc can have a maximum of 99 play list and 999 scenes. 
These limits may be reduced under some conditions.
PL Copy
PL Erase
Enter Title
PropertiesPress [2] to select 
“Erase” and press 
[ENTER].
The play list is erased.
Press [2] to select 
“Copy” and press 
[ENTER].
The copied play list appears at the 
bottom of the list.
➜ page 27, Playing play list scenes
Entering text ➜ page 45 e.g., DVD-RAM
Preparation
Press [HDD] or [DVD] to select the drive.[HDD] 
[RAM]
[HDD] 
[RAM]
[HDD] [RAM]
[HDD] [RAM]
[HDD] [RAM]
[HDD] [RAM]Once a play list has been erased, 
it is irretrievable. Check carefully 
before proceeding. 
						

							Editing
43
RQT6570
PLAY LIST
Add Scenes
0 : 00 . 05StartEnd3
Start5
EndNextExit Scene No.0 : 00 . 05
RETURN ENTERSELECT
--:--.--
PLAY01
PLAY LIST No.1 Dinosaur
Erase Scenes
Ye s N o
RETURN
ENTERSELECT
Erase this scene?
DVD
Repeat to erase other scenes.Press [3, 4] to 
select “Exit” 
and press 
[ENTER].
The new scene is 
inserted before the 
highlighted scene.
Press [3, 4] to select “Next” and press [ENTER]. (Repeat to add other scenes.)
Repeat to move other scenes.
Press [3, 4] to select “Prev.” or “Next” and press [ENTER]. (Repeat to re-edit other scenes.)Press [3, 4, 2, 1] to select the position 
to which you want to move the scene and 
press [ENTER].
The scene is moved and inserted before the 
highlighted scene.
Press [2] to 
select “Yes” 
and press 
[ENTER].
≥ The selected scene is 
erased from the play list.
≥ The play list itself is 
erased if you erase all the 
scenes in it.
∫ Add (maximum 999 scenes)
∫ Erase ∫ Re-edit ∫ Move
Press [3, 4] 
to select “Exit” 
and press 
[ENTER].
The re-edited 
scene replaces 
the old one. The scene is moved.
PLAY LISTRe-edit Scenes
0 : 00 . 05StartEnd
Start
1
EndNextExit Scene No.0 : 35 . 20
RETURN ENTERSELECT
0 : 35 . 20
33
01PLAYPrev.
Press [3, 4, 2, 1] 
to select the place 
where you want to 
add the scene and 
press [ENTER].Press [ENTER] 
at the start point 
of the scene.Press [ENTER] 
at the end point 
of the scene.
Press [3, 4, 2, 1] 
to select the scene 
and press [ENTER].
Press [3, 4, 2, 1] 
to select the scene 
and press [ENTER].Press [ENTER] 
at the start point 
of the scene.Press [ENTER] 
at the end point 
of the scene.
Press  
[3, 4, 2, 1] to 
select the scene 
and press 
[ENTER].
Once a scene has 
been erased, it is 
irretrievable. Check 
carefully before 
proceeding.
[Note]
001
≥ Use search and slow-motion to find the start and end 
points.
≥ You cannot specify an end point before a start point, or a 
start point after an end point.
≥ You may not be able to specify points within 3 seconds of 
each other.
≥ Play pauses if the end of the last program is reached 
during this procedure.≥ You cannot edit still picture images.
≥ Depending on the state of recording, the actual number of 
play lists or scenes that can be recorded may be 
less than that specified in this manual.
≥ The picture illustration on the right may be 
shown in the HDD play list scene display. This 
picture illustration indicates pictures that are 
permitted to be recorded only once.
DVDPLAY LIST No.1 Dinosaur 
						

							Editing
44
RQT6570
Creating play lists
[HDD] [RAM]
Specify start and end points to create scenes, then specify the order
in which they are to be played. These scenes are not recorded sep-
arately so this doesn’t use much capacity.
You can create a maximum of 99 play lists and 999 scenes on a
DVD-RAM and HDD.
1While stopped
Press [PLAY LIST].
2Press [3, 4] to select “– – – –/– –” and
press [ENTER].
3Press [ENTER] at the start point.
4Press [ENTER] at the end point.
To specify another scene
Select “Next” and press [ENTER], then repeat steps 3 and 4.
5Press [3, 4] to select “Exit” and
press [ENTER].
The play list screen appears.
To clear the play list screen
Press [RETURN].
To stop partway through
Press [RETURN].
For your reference
≥You cannot create or edit play lists if the disc is protected. [RAM]
≥You cannot specify an end point before a start point, or a start
point after an end point.
≥You may not be able to specify points within 3 seconds of each
other.
≥Use search and slow-motion to find the start and end points. 
≥Play pauses if the end of the last program on the disc is reached
during this procedure.
≥Depending on the state of recording, the actual number of play
lists that can be recorded may be less than that specified in this
manual.
≥Pressing [:], [9] in step 3 and 4 allows you to select pro-
grams in the same drive.
DV D
VCR Plus+ TV/VIDEOREC MODEREC
CH
VOLUME
TVTVDV D
123
789
0
10 0
4
56
SLOW/SEARCH
DIRECT NAVIGATOR
TOP
MENUMENU
RETURNFUNCTIONSPROG/CHECKDISPLAYTIME SLIPADD/DLT
ENTER
PLAY LIST
CANCEL
POWER
ÍÍ
HDDDVD
3, 4, 2, 1
ENTER
RETURN
PLAY LIST
PLAY LIST
------
Auto action
USJ01 10/23 006
006 0:03
02 10/26 0:07
03 10/21 0040:06Dinosaur
3
3
1
1
1
1
1
1
--- -- --/-- --:--
0   - -   9No.
RETURN ENTER
SELECT
NoDATE TOTALSCENEEDIT TITLE---
---------
HDD
PLAY LIST
0 : 00 . 05StartEnd3
Start1
EndNextExit Scene No.
0 : 00 . 05
RETURN ENTER
SELECT
--:--.--
PLAY LIST No.4
PLAY001Creation
HDD
HDD:The location of the 
whole program’s start point
DVD-RAM:The location of 
the whole disc’s start point
0 : 00 . 05StartEnd
Start1
EndNextExit Scene No.
0 : 35 . 20
RETURN ENTER
SELECT
0 : 35 . 20
33
PLAY LIST No.4 
001PLAY LISTCreation
HDD
HDD:The location of the 
whole program’s end point
DVD-RAM:The location of
the whole disc’s end point 
						

							Editing
45
RQT6570
Entering text
[HDD] [RAM] [DVD-R] [CARD]
This page shows how to enter text for:
≥Disc titles (➜page 38)
≥Program titles for timer recording (➜pages 34 and 35)
≥Program titles (➜page 40)
≥Play list titles (➜page 42)
≥Folder titles of still pictures (➜page 25)
If you give a title to a program when setting timer recording, it will
become easier to find the program when using Direct Navigator.
1After the titling screen appears
Press [3, 4, 2, 1] to select the 
character and press [ENTER].
Repeat step 1 to enter other characters.
2Press [∫].
The title is entered and the screen disappears.
≥You can also finish entering the title by selecting “SET” and
pressing [ENTER].
Using the numbered buttons to enter characters
e.g., entering the letter “R”
1Press [7] to move to the
7th row.
2Press [7] twice to high-
light “R”.
3Press [ENTER].
≥You can enter a space by
pressing [100] and then
[ENTER].
To erase a character
1Press [3, 4, 2, 1] to select the character you want to
erase in the title field.
2Press [;].
You can also erase characters by selecting “ERASE” and press-
ing [ENTER].
[Note]
If Disc Protection (➜page 38) or Cartridge Protection (➜page 8) is
activated, you cannot enter the title. Deactivate the protection before
entering the title. [RAM]
DV D
VCR Plus+ TV/VIDEOREC MODEREC
CH
VOLUME
TVTVDV D
123
789
0
10 0
4
56
SLOW/SEARCH
DIRECT NAVIGATOR
TOP
MENUMENU
RETURNFUNCTIONSPROG/CHECKDISPLAYTIME SLIPADD/DLT
ENTER
PLAY LIST
CANCEL
POWER
ÍÍ
HDDDVD
3, 4, 2, 1
ENTER
∫;
Numbered
buttons
ENTER
_Enter Title
1 1
2
3
4
5
6
7
8
9
0
1002345
ABC a
DE F d
GH I
NOg
JKL j
M
m
67890
bcij
ef /l%
hifl$¢
&
klON@
n]_o[
SPACE
SETERASE
SELECT
0100PQRS p
TUV t
WX Y Z wqrs ( )
uv { }-
xyz
`^| 
! ?\
.
,

:
; ––
RETURN
π;
Title field: shows the text you have entered
5
6
7
8NO
JKL
M
PQRS
TUV
7
77 
						

							Editing
46
RQT6570
Editing still pictures (JPEG)
JPEG
JPEG1/2INPUTPC card        100_PANA
Album
Slide Show
Copy
All copy of PC card
RETURNENTERSELECT
SLOW/SEARCH
DIRECT NAVIGATOR
TOP
MENUMENU
RETURNFUNCTIONSPROG/CHECKDISPLAYTIME SLIPADD/DLT
ENTER
PLAY LIST
HDDDVD
3, 4, 2, 1
ENTER
RETURN
FUNCTIONS
ENTERRETURN
SELECT
INPUTJPEG
COPY
1 / 1Prev. Next--------
--------
----
000100020003
0004
FolderCopyPC card           100_PANA
0   –   9 Select Page
RETURN
PC card  Copy fromJPEG
ALL COPY
Copy all JPEG from PC card.
Copy to\JPEG\DCIM001HDD
All copyCancel
ALL COPY OF PC CARD
ENTERRETURN
JPEG
INPUT
0   –   9  No
DVDHDD
PC card
\DCIM\@_PANAPC card          100_PANA
100_PANADCIM
           0043       0045
101_DVDD
001
002
003
Picture 
File
3
3
[CARD] [HDD] [RAM]
You can select the folder for 
editing. 
INPUT
Displaying still pictures (Album Display) ➜ page 25
Album
Copy Operation
e.g., PC card: First pageSlide Show
[CARD] [HDD] [RAM]
You can copy the whole folder or 
selected still pictures to PC card, 
HDD or DVD-RAM.
(maximum of 300 folders, 3000 
files)
To display still pictures one by one with constant interval (Slide 
Show) ➜ page 25
[Note]≥ When there is no folder in the copying drive, a new folder will be created.
≥ When there is a folder in the copying drive, copying will continue from the last of the 
existing still pictures.
≥ When copying a folder, any files in the folder besides the still pictures are also copied.
≥ Folders lower than the folder to be copied will not be copied.
≥ If the space on the copying drive runs out or the number of files/folders to be copied 
exceeds the maximum, copying will stop partway through.
≥ If no title has been entered for the folder at the copying drive, the title from the copying 
source will be entered. It is recommended that the title is entered at the copying source.
≥ After copying, it may take some time to download the copying source information.
≥ Print (DPOF) number setting (➜ page 48) is not transferred.
All copy of PC card
[CARD]
You can copy the whole contents of 
the PC card to HDD or DVD-RAM.
(maximum of 300 folders, 3000 
files)
[Note]≥ A new folder will be created in the copying drive.
≥ Any files in the folder besides the still pictures are also copied.
≥ Folders lower than the folder to be copied will not be copied.
≥ If the space on the copying drive runs out or the number of files/folders to be copied 
exceeds the maximum, copying will stop partway through.
≥ After copying, it may take some time to download the copying source information.
≥ Print (DPOF) number setting (➜ page 48) is not transferred.
To insert/remove the PC card(➜ page 25) 
When the card indicator in the unit display 
is flashing, the card is being read from or 
written to. Do not turn off the power or 
remove the card. Such action may result in 
malfunction or loss of the card’s contents.
To stop set up processPress [RETURN].
≥ You can also use [3, 4, 2, 1] to select 
“Cancel” or “No” and press [ENTER].
[Note]You can only access “INPUT”, “Album” and 
“Slide Show” if the PC card is set to Write 
Protect ([CARD] ➜ page 9) or if Disc 
Protection ([RAM] ➜ page 38) or Cartridge 
Protection is activated ([RAM] ➜ page 8). 
Deactivate the protection to access other 
items.While stopped
Press [FUNCTIONS].
Press [3, 4, 2, 1] to 
select “JPEG” and press 
[ENTER].
Press [3, 4] to select 
the item and press 
[ENTER].
To select a folder other than the 
one currently being displayed, 
first highlight “INPUT” and press 
[ENTER].
Erase, Protect, Print (DPOF) ➜ page 48
Settings 
➜ page 25, “To change the display timing”
 
➜ page 48, “PC card Format” 
						

							Editing
47
RQT6570
0001
[Note]≥ “Picture” and “Files” refer to numbers inside the 
folder selected. Lower files are not included.
≥ If there is more than one upper folder, pressing 
[:], [9] will switch between them [➜ page 9, 
“Folders that can be displayed/saved” (underlined 
section)].
Press [2, 1] to select 
“HDD” or “DVD”.Press [3, 4, 2, 1] to select “All 
copy” and press [ENTER].
All still pictures are copied, and ALL COPY 
screen reappears.
[Note]Still pictures are copied but non-compatible files and folders will not copied.  
(➜ page 9, “Folders that can be displayed/saved”). 
To select still pictures one by onePress [3, 4, 2, 1] to select a still picture and press 
[ENTER]. (A check mark appears on the still picture.)
To select all the still pictures in the folderPress [3, 4, 2, 1] to select “Folder” and press [ENTER]. 
(A check mark appears on the folder’s name; check marks 
inputted separately will be erased.)
To erase check marksPress [3, 4, 2, 1] to select the folder or still picture with the 
check mark and press [ENTER].
To select the copying driveWhile the confirmation screen is displayed
1. Press [3, 4] to select “Destination” and press [ENTER].
2. Press [2] and [3, 4] to select the drive.
3. Press [1] and [3, 4] to select the folder and press [ENTER].
≥ Some folders cannot be copied to [➜ page 9, “Folders that can be 
displayed/saved” (indicated by §)].
Press [3,4] to 
select still picture’s 
folder and press 
[ENTER]. Press [2] and 
[3,4] to select 
the drive and 
press [1].To enter the folder’s titlePress [1] to select “Folder Title” and press [ENTER].
(➜ Entering text, page 45)
≥ You can enter up to 36 characters.
≥ Folder titles entered using this unit will only be displayed using 
this unit. Folders entered using this unit are written to the 
TITLE.DVD file.
≥ If there is not enough space for the entry or if the limit for the 
number of files has  been exceeded (➜ Still pictures, page 9), 
the title cannot be entered.
Select the 
copying 
drive.  
(➜ below)
Press [3, 4, 2, 1] 
to select “Copy” 
and press [ENTER].
Copying still pictures 
begins.
Press [3, 4, 2, 1] 
to select “Copy” 
and press [ENTER].
A confirmation screen 
appears.
Press [3, 4, 2, 1] to select a 
folder or still picture and press 
[ENTER]. 
(See below)
A check mark appears on 
the still picture.
≥ Repeat this if you select more than one 
still picture. 
						

							Editing
48
RQT6570
Editing still pictures (JPEG)
JPEG
JPEG2/2PC card          100_PANA
Erase
Protect
Print (DPOF)
Settings
RETURNENTER
SELECT
ENTERRETURN
SELECT
INPUTJPEG
ERASE
1 / 1Prev. Next--------
--------
----
000100020003
0004
FolderErasePC card         100_PANA
0   –   9Select Page
ENTERRETURN
SELECT
INPUTJPEG
PROTECT
1 / 1Prev. Next--------
--------
----
000100020003
0004
FolderSet UpCancelPC card          100_PANA
0   –   9Select Page
ENTERRETURN
INPUTJPEG
DPOF
1 / 1Prev.
Next--------
--------
----
000100020003
0004
WholeSet UpPC card          100_PANA
0   –   9Select Page
SELECT
SLOW/SEARCH
DIRECT NAVIGATOR
TOP
MENUMENU
RETURNFUNCTIONSPROG/CHECKDISPLAYTIME SLIPADD/DLT
ENTER
PLAY LIST
HDDDVD
3, 4, 2, 1
ENTER
RETURN
FUNCTIONS
!?
!?
[CARD] [HDD] [RAM]
You can erase whole folders or 
selected still pictures.
Erase
[CARD] [HDD] [RAM]
You can set protection for whole 
folders or for individual still pictures.
Protect
Print (DPOF) Operation
e.g., PC card: Second page
To insert/remove the PC card
(➜ page 25) 
When the CARD indicator in the unit 
display is flashing, the card is being read 
from or written to. Do not turn off the power 
or remove the card. Such action may result 
in malfunction or loss of the card’s 
contents.
To stop set up processPress [RETURN].
≥ You can also use [3, 4, 2, 1] to select 
“Cancel” or “No” and press [ENTER].
[Note]You can only access “Slide Show” in 
“Settings” if the PC card is set to Write 
Protect ([CARD] ➜ page 9) or if Disc 
Protection ([RAM] ➜ page 38) or Cartridge 
Protection is activated ([RAM] ➜ page 8). 
Deactivate the protection to access other 
items.
Settings
[CARD]
You can select a whole folder or 
individual pictures for printing and 
specify the number of prints to be 
made (maximum 999 files).
[Note]≥ Settings cannot be made for folders and files not in accordance with DCF standards.
≥ Print settings (DPOF) made using this unit may not be viewable on other equipment.
≥ Settings cannot be made if there is no remaining space on the PC Card.
≥ All settings made on other equipment, except the number of prints, will be canceled.
Slide Show
PC card Format [Note]
≥ When you erase folders, files other than still pictures in the folder are also 
erased.
≥ Folders lower than the folder to be erased will not be erased.
≥ To erase files other than still pictures, select the folder containing the file and 
erase.
[CARD]
You can erase all still 
pictures in the PC card.
Press [3, 4, 2, 1] to 
select “JPEG” and press 
[ENTER].
Press [3, 4] to select 
the item and press 
[ENTER].
To select a folder other than the 
one currently being displayed, 
first highlight “INPUT” and press 
[ENTER] (➜ page 46). While stopped
Press [FUNCTIONS].
≥ “INPUT”, “Copy” and “All copy of PC card” ➜ page 46
≥ “Album” ➜ page 25, Displaying still pictures (Album Display)
≥ “Slide Show” ➜ page 25, To display still pictures one by one 
with constant interval (Slide Show)
[CARD] [HDD] [RAM]
To display still pictures one by one 
with constant interval (Slide Show) 
➜ page 25 
						

							Editing
49
RQT6570
0001
0001
0001
[Note]The cards formatted on this unit may not be usable 
on other equipment. Once activated, material 
cannot be returned to its 
original form, including 
protected still pictures. 
Check carefully before 
proceeding.
Once activated, recorded 
contents (including protected 
still pictures and computer 
data) will be completely erased. 
Check carefully before 
proceeding.
Press [3, 4, 2, 1] to select a 
still picture and press [ENTER].
A check mark appears on  
the still picture.
≥ Repeat this if you erase more than one still 
picture.
Press [3, 4, 2, 1] 
to select 
“Erase” 
and press [ENTER].A confirmation screen 
appears.
Press [2] to select 
“
Erase” and press 
[ENTER].
Selected still pictures are 
erased, and the still 
picture select screen 
reappears.
To select all the still pictures in the folderPress [3, 4, 2, 1] to select “Folder” and press [ENTER].
(A check mark appears on the folder’s name; check marks 
inputted separately will be erased.)
To change print (DPOF) settings1. Press [3, 4, 2, 1] to select “Whole” or a still picture with the DPOF 
mark and press [ENTER].
2. Press [3, 4, 2, 1] to select “Set Up” and press [ENTER].
3. Press [2, 1] to change the print setting
≥ The print setting will be canceled if you set the number of print to “0”.
4. Press [3, 4, 2, 1] to select “Set” and press [ENTER].
To erase check marksPress [3, 4, 2, 1] to select the folder or still picture with the check 
mark and press [ENTER].
To select all the still pictures in the folderPress [3, 4, 2, 1] to select “Folder” and press [ENTER].
(A check mark appears on the folder’s name; check marks 
inputted separately will be erased.)To erase check marksPress [3, 4, 2, 1] to select the folder or still picture with the check 
mark and press [ENTER].
To select all the still pictures in the folderPress [3, 4, 2, 1] to select “Whole” and press [ENTER].
(A check mark appears on the folder’s name; check marks 
inputted separately will be erased.)
Press [3, 4, 2, 1] to select a still picture and 
press [ENTER].
A check mark appears on the still picture.
≥ Repeat this if you set protection of more than one still picture.
Press [3, 4, 2, 1] to 
select “Set Up” or 
“Cancel” and press 
[ENTER].Press [2] to select 
“Yes” and press 
[ENTER].
The lock symbol appears 
on the still picture when 
the still picture is 
protected.
Press [3, 4, 2, 1] to select a 
still picture and press [ENTER].
A check mark appears on the 
still picture.
≥ Repeat this if you print more than one still 
picture.
Press [3, 4, 2, 1] 
to select “Set Up” 
and press [ENTER].Press [2, 1] to 
set number of 
print (0 to 9).Press [3, 4, 2, 1] 
to select “Set” and 
press [ENTER].
The DPOF mark 
appears if you set 
one or more 
pictures to print.
Press [2] to 
select 
“Yes” 
and press 
[ENTER].Press [2] to 
select “Start”  and 
press [ENTER].Format begins. 
						

							Advanced operation
50
RQT6570
Using on-screen menus
1Press [DISPLAY].
e.g. DVD-RAM
2Press [3, 4] to select the menu and
press [1].
3Press [3, 4] to select the item and
press [1].
4Press [3, 4] to select the setting.
To return to the previous screen
Press [RETURN].
When you are finished
Press [DISPLAY].
For your reference
≥The screens depend on the disc contents.
≥Depending on the condition of the unit (playing, stopped, etc.) and
disc contents, there are some items that you cannot select or
change.Not available when playing CDs.
e.g., DVD-RAM
[A]Soundtrack/Subtitle language
[B]Audio attributes
LPCM/ÎDigital/DTS/MPEG: Signal type
k (kHz):Sampling frequency
b (bit):Number of bits
ch (channel):Number of channels
 
.1: Subwoofer signal (not displayed if there
is no subwoofer signal)
0: No surround
1: Mono surround
2: Stereo surround (left/right)
 
1: Center
2: Front leftiFront right
3: Front leftiFront rightiCenter
For your reference
≥When playing back recordings of SAP broadcasts, “1+1 ch” will be
displayed.
≥You can only select subtitles, soundtracks, and angles if they are
recorded on the disc.
≥Some discs allow changes to soundtracks, subtitles, and angles
only by using the disc’s menus.
≥If the subtitles overlap closed captions recorded on discs, turn the
subtitles off.
Common procedures
DV D
VCR Plus+ TV/VIDEOREC MODEREC
CH
VOLUME
TVTVDV D
123
789
0
10 0
4
56
SLOW/SEARCH
DIRECT NAVIGATOR
TOP
MENUMENU
RETURNFUNCTIONSPROG/CHECKDISPLAYTIME SLIPADD/DLT
ENTER
PLAY LIST
CANCEL
POWER
ÍÍ
HDDDVD
3, 4, 2, 1
ENTER
RETURN
DISPLAY
Disc
Video
Audio
PlaySound track
Subtitle1
Audio channel
OFF
L R
Î Digital   2/0 ch
Menu Item Setting
Disc menu
Item Content
Sound trackSoundtrack language [DVD-V] 
See [A] below.
Audio attribute [HDD] [RAM] [DVD-R] [DVD-V] 
See [B] below.
Karaoke vocals, on and off
(Karaoke [DVD-V] only)
Solo: ON()OFF
Duet: OFF()V1+V2()V1()V2
^=======J
SubtitleSubtitle language [DVD-V] 
See [A] below.
Subtitle on/off [HDD] [RAM] [DVD-R] [DVD-V] 
Angle Angle number [DVD-V]
Audio channel [HDD] [RAM] [VCD] (➜page 30)
PBCPlayback control on/off [VCD]
Indicates whether menu play (playback con-
trol) is on or off.
ENG: English
FRA: French
DEU: German
ITA: Italian
ESP: Spanish
NLD: DutchSVE: Swedish
NOR: Norwegian
DAN: Danish
POR: Portuguese
RUS: Russian
JPN: JapaneseCHI: Chinese
KOR: Korean
MAL: Malay
VIE: Vietnamese
THA: Thai
¢: Others
Disc
Video
Audio
PlaySound track
Subtitle1
Audio channel
OFF
L R Î Digital   2/0 ch
!?
e.g., 3/2 .1ch