Panasonic Dmr E20 Operating Instructions Manual
Here you can view all the pages of manual Panasonic Dmr E20 Operating Instructions Manual. The Panasonic manuals for DVD Recorder are available online for free. You can easily download all the documents as PDF.
Page 11
11 RQT6035 Getting started Playing discs Playing discs (➡ page 22) Using the direct navigator (➡ page 56) Recording and Playing at the same time Chasing play (➡ page 28) Simultaneous rec and play (➡ page 28) Reviewing the recorded images while recording (Time Slip) (➡ page 29) Using DVD-R DVD-R (➡ page 7) Recording television programs (➡ page 26) Playing discs (➡ page 22) Using the direct navigator (➡ page 56) Recording from a video cassette recorder Recording from a video cassette recorder (➡...
Page 12
RQT6035 12 Getting started A B R6, AA 1 2 30 30 TV DV D The remote control ABatteries Insert so the poles ( and ) match those in the remote control. Do not use rechargeable type batteries. Do not:mix old and new batteries. use different types at the same time. heat or expose to flame. take apart or short circuit. attempt to recharge alkaline or manganese batteries. use batteries if the covering has been peeled off. Mishandling of batteries can cause electrolyte leakage which can damage items...
Page 13
13 RQT6035 Getting started A 2 TV CH TV/AV PROG / CHECK TOP WINDOWFRAME SKIP STOP VCR Plus + REC TIME SLIP CM SKIP V. S . S . ACTION AUDIOADD/DLT REC MODECANCELINPUT SELECT LAST MARKER MARKER WRITE CHDVD 123 456 789 0 PAUSE PLAY SLOW/SEARCH S TAT U S RETURNENTER VOLPOWER POWER OPEN/CLOSETCERIDROTAGIVANTOPMENUMENU DISPLAYTSILYALP 100 POWER CH TV/AVVOLPOWERTV 123 456 789 0 100 123 456 789 0 2 2 TV, , ,CH TV, TV/AVTV, , ,VOL TV DV DDVD, TV The remote control Television operation You can...
Page 14
RQT6035 14 Getting started VIDEO PBPRYVIDEO OPTICAL R LAUDIO (L1) (L3)AC INT OUT1 OUT2 IN1 IN3 (PCM/BITSTREAM) DIGITAL AUDIO OUT R LAUDIO R LAUDIO R LAUDIO S-VIDEO S-VIDEO VIDEO S-VIDEO VIDEOS-VIDEO RF-IN VHF/UHF RF-OUT COMPONENT VIDEO OUT AUDIO INVIDEO IN VHF/UHF RF IN Antenna and television connections Audio/Video cable (included) Yellow (VIDEO) White (L) Red (R)Preparation Refer to the television’s operating instructions. Turn the television off and disconnect its AC power supply...
Page 15
15 RQT6035 Getting started VIDEO PBPRYVIDEO OPTICAL R LAUDIO (L1) (L3)AC INT OUT1 OUT2 IN1 IN3 (PCM/BITSTREAM) DIGITAL AUDIO OUT R LAUDIO R LAUDIO R LAUDIO S-VIDEO S-VIDEO VIDEO S-VIDEO VIDEOS-VIDEO RF-IN VHF/UHF RF-OUT COMPONENT VIDEO OUT S VIDEO INCOMPONENT VIDEO YPRPB Connecting to a TV with S-video or component video input terminals S-video cable (not included)Video cable (not included) S VIDEO OUT terminalThe S-video terminal achieves a more vivid picture than the VIDEO OUT...
Page 16
![Page 16
RQT6035
16
Getting started
Plug-in Auto Tuning
After you purchase the unit, plug it into your household AC outlet,
and turn it on for the first time, the unit automatically tunes in all the
channels it can receive and sets the clock.
Preparation
Confirm that the antenna is connected correctly.
Turn on the television and select the appropriate video input to suit
the connections to this unit.
1Press [, POWER] to turn the unit on.
2Press [ENTER].Plug-in Auto Tuning starts and the unit puts the stations...](http://img.usermanuals.tech/thumb/58/66396/w300_dmr-e20_en_om_d-15.png "Page 16
RQT6035
16
Getting started
Plug-in Auto Tuning
After you purchase the unit, plug it into your household AC outlet,
and turn it on for the first time, the unit automatically tunes in all the
channels it can receive and sets the clock.
Preparation
Confirm that the antenna is connected correctly.
Turn on the television and select the appropriate video input to suit
the connections to this unit.
1Press [, POWER] to turn the unit on.
2Press [ENTER].Plug-in Auto Tuning starts and the unit puts the stations...")
RQT6035 16 Getting started Plug-in Auto Tuning After you purchase the unit, plug it into your household AC outlet, and turn it on for the first time, the unit automatically tunes in all the channels it can receive and sets the clock. Preparation Confirm that the antenna is connected correctly. Turn on the television and select the appropriate video input to suit the connections to this unit. 1Press [, POWER] to turn the unit on. 2Press [ENTER].Plug-in Auto Tuning starts and the unit puts the stations...
Page 17
![Page 17
17
RQT6035
Getting started
Plug-in Auto Tuning
Note
Plug-in Auto Tuning does not work if you turn the unit on by press-
ing [ , OPEN/CLOSE] or [
, PLAY].
After the unit sets the clock automatically, it then adjusts the clock
everyday.
If the unit sets the time incorrectly, use “Time Zone Adjust” to cor-
rect it (➡ page 89).
You can give the stations captions (➡ page 92).
If you connect the unit through a cable TV box or DSS receiver
(➡ page 76), tune to your local PBS station before starting auto...](http://img.usermanuals.tech/thumb/58/66396/w300_dmr-e20_en_om_d-16.png "Page 17
17
RQT6035
Getting started
Plug-in Auto Tuning
Note
Plug-in Auto Tuning does not work if you turn the unit on by press-
ing [ , OPEN/CLOSE] or [
, PLAY].
After the unit sets the clock automatically, it then adjusts the clock
everyday.
If the unit sets the time incorrectly, use “Time Zone Adjust” to cor-
rect it (➡ page 89).
You can give the stations captions (➡ page 92).
If you connect the unit through a cable TV box or DSS receiver
(➡ page 76), tune to your local PBS station before starting auto...")
17 RQT6035 Getting started Plug-in Auto Tuning Note Plug-in Auto Tuning does not work if you turn the unit on by press- ing [ , OPEN/CLOSE] or [ , PLAY]. After the unit sets the clock automatically, it then adjusts the clock everyday. If the unit sets the time incorrectly, use “Time Zone Adjust” to cor- rect it (➡ page 89). You can give the stations captions (➡ page 92). If you connect the unit through a cable TV box or DSS receiver (➡ page 76), tune to your local PBS station before starting auto...
Page 18
![Page 18
RQT6035
18
Getting started
Channel settings
Using the remote control to
add and delete channels
Remote control only
Use this function if:
Channels were not set correctly using automatic tuning.
A channel that should have been set wasn’t.
A channel’s reception is poor and you want to delete it.
Preparation
Switch [DVD, TV] to “DVD”.
1Press the numbered buttons to select
a channel.
Example:“5”: [0] ➡ [5]
Example:“15”: [1] ➡ [5]
Example:“115”: [100] ➡ [1] ➡ [5]
You can also use [, , CH] when you...](http://img.usermanuals.tech/thumb/58/66396/w300_dmr-e20_en_om_d-17.png "Page 18
RQT6035
18
Getting started
Channel settings
Using the remote control to
add and delete channels
Remote control only
Use this function if:
Channels were not set correctly using automatic tuning.
A channel that should have been set wasn’t.
A channel’s reception is poor and you want to delete it.
Preparation
Switch [DVD, TV] to “DVD”.
1Press the numbered buttons to select
a channel.
Example:“5”: [0] ➡ [5]
Example:“15”: [1] ➡ [5]
Example:“115”: [100] ➡ [1] ➡ [5]
You can also use [, , CH] when you...")
RQT6035 18 Getting started Channel settings Using the remote control to add and delete channels Remote control only Use this function if: Channels were not set correctly using automatic tuning. A channel that should have been set wasn’t. A channel’s reception is poor and you want to delete it. Preparation Switch [DVD, TV] to “DVD”. 1Press the numbered buttons to select a channel. Example:“5”: [0] ➡ [5] Example:“15”: [1] ➡ [5] Example:“115”: [100] ➡ [1] ➡ [5] You can also use [, , CH] when you...
Page 19
![Page 19
19
RQT6035
Getting started
Channel settings
VCR Plus guide
channel settings
Set these guide channels so you can use VCR Plus codes for tim-
er recording. Before starting the settings, prepare a chart showing
the channels, the station’s name, and the guide channel.
For example:
1Press [ACTION].The ACTION screen appears.
2Use the joystick [
,
] to select the
Set Up tab.
3Use the joystick [, ] to select
“Channel Settings” and press
[ENTER].
(Continued on next page) Write down all the stations
you can...](http://img.usermanuals.tech/thumb/58/66396/w300_dmr-e20_en_om_d-18.png "Page 19
19
RQT6035
Getting started
Channel settings
VCR Plus guide
channel settings
Set these guide channels so you can use VCR Plus codes for tim-
er recording. Before starting the settings, prepare a chart showing
the channels, the station’s name, and the guide channel.
For example:
1Press [ACTION].The ACTION screen appears.
2Use the joystick [
,
] to select the
Set Up tab.
3Use the joystick [, ] to select
“Channel Settings” and press
[ENTER].
(Continued on next page) Write down all the stations
you can...")
19 RQT6035 Getting started Channel settings VCR Plus guide channel settings Set these guide channels so you can use VCR Plus codes for tim- er recording. Before starting the settings, prepare a chart showing the channels, the station’s name, and the guide channel. For example: 1Press [ACTION].The ACTION screen appears. 2Use the joystick [ , ] to select the Set Up tab. 3Use the joystick [, ] to select “Channel Settings” and press [ENTER]. (Continued on next page) Write down all the stations you can...
Page 20
![Page 20
RQT6035
20
Getting started
Channel settings
4Use the joystick [, ] to select “VCR
Plus CH Setting” and press
[ENTER].
For example, when the current antenna system is CATV.
5Use the joystick [, ] to select
the guide channel you want to set
and use the joystick [].
The screen scrolls a page at a time if you hold the joy-
stick up or down.
Use the joystick [, ] to select
the channel corresponding to the
guide channel and use the joystick
[].
Repeat steps and as necessary.
6Press [ENTER].The...](http://img.usermanuals.tech/thumb/58/66396/w300_dmr-e20_en_om_d-19.png "Page 20
RQT6035
20
Getting started
Channel settings
4Use the joystick [, ] to select “VCR
Plus CH Setting” and press
[ENTER].
For example, when the current antenna system is CATV.
5Use the joystick [, ] to select
the guide channel you want to set
and use the joystick [].
The screen scrolls a page at a time if you hold the joy-
stick up or down.
Use the joystick [, ] to select
the channel corresponding to the
guide channel and use the joystick
[].
Repeat steps and as necessary.
6Press [ENTER].The...")
RQT6035 20 Getting started Channel settings 4Use the joystick [, ] to select “VCR Plus CH Setting” and press [ENTER]. For example, when the current antenna system is CATV. 5Use the joystick [, ] to select the guide channel you want to set and use the joystick []. The screen scrolls a page at a time if you hold the joy- stick up or down. Use the joystick [, ] to select the channel corresponding to the guide channel and use the joystick []. Repeat steps and as necessary. 6Press [ENTER].The...