Panasonic Dmr E100 Operating Instructions Manual

							31
RQT6986
Dubbing
To add or remove from the dubbing list
While the Dubbing List (➜ step 5-1) is displayed
1Press [3, 4] to select the dubbing list and press [1].
2Press [3, 4] to select an item and press [ENTER].
≥If you select “Add”, carry out steps 5-3 and 5-4. Addition will
take place above the program selected in step 1.
≥If you select “Erase” or “Erase All”, a confirmation screen will be
displayed. Press [2, 1] to select “Yes” or “No” and press
[ENTER] (Return to Dubbing List).
[Note]
≥Dubbing list’s content will be erased in the following cases.
–If the power is turned off or the original disc is ejected. (Nothing is
erased if the power is turned off when dubbing from the HDD).
–Erasing an original program or play list.
–When the SD VIDEO (MPEG4) program is erased on the original
drive or when recording or dubbing SD VIDEO (MPEG4) pro-
grams on the original drive.
≥When dubbing using the “MPEG2 to 4” mode, the displayed
“Remain” value is calculated using video segments that contain
the most information. You may be able to dub even if “Amount” has
exceeded “Remain” when video images do not change rapidly.
≥Regarding the time until dubbing ends (High Speed mode)
–You can high speed dub Dolby Digital audio programs. LPCM
audio programs take about the same amount of dubbing time.
–The current progress indicator is corrected each time the pro-
gram being dubbed changes.
–When there are programs mixed with LPCM audio and Dolby
Digital audio, the dubbing time display may fluctuate significantly.
–When dubbing SD VIDEO (MPEG4) programs, the time display
may fluctuate.
≥It is not possible to activate timer recording during dubbing.
≥Title information etc. is dubbed as is. However, when using
“MPEG2 to 4” mode, protect settings are not dubbed. Markers are
only dubbed if you use “High Speed” dubbing mode. 
≥Select the audio format for recording SAP broadcast from “Select
MTS” in the setup menu (➜ page 53, Audio) when:
 –Dubbing to a DVD-R.
–Dubbing sound in LPCM.
–Dubbing programs in “MPEG2 to 4” mode.
≥
Use [:], [9] to switch between folders when there are other
folders on the mobile hard disc which are not displayable on screen.
[HDD] > [RAM] [DVD-R]
You can dub programs and play lists being played from the HDD to a
DVD-RAM, DVD-R.
[HDD] [RAM]
 > [SD]
You can dub SD VIDEO (MPEG4) programs being played from the
HDD or DVD-RAM to a card.
1During play or while paused
Press [DUBBING].
The confirmation screen appears.
2Press [2, 1] to select “Yes” and
press [ENTER]. 
To stop dubbing
Press and hold [RETURN] for 3 seconds.
≥If stopped partway, dubbing will be up to that point. However, in
high speed mode, only programs that have completed dubbing at
the point stopped are dubbed. (Remaining disc space will be
reduced once you have recorded/dubbed to DVD-R.)
[Note]
≥This function works even while the program list or play list screen
is being displayed.
≥It is not possible to activate timer recording during dubbing.
≥Programs with recording limitations (including play lists made from
those programs) cannot be dubbed.
The recording mode is set as follows:
≥High speed mode: 
–When dubbing to a DVD-RAM.
–When the programs recorded with “Rec in DVD-R high speed
mode” (➜page 52) set to “On” and play lists created from that
programs are being dubbed to a DVD-R.
–When dubbing a SD VIDEO (MPEG4) program to a card.
≥Original dubbing mode: 
–When the programs recorded with “Rec in DVD-R high speed
mode” set to “Off ” is being dubbed to a DVD-R.
≥FR (Flexible Recording) (➜page 15): 
–Based on the above conditions, the mode automatically changes
to FR when there is not enough room left on the disc.
–When dubbing play lists created from the programs recorded with
“Rec in DVD-R high speed mode” set to “Off ” to a DVD-R.
§1Refer to the approximate recording times. (➜below) §2You cannot select this mode if “MPEG4 Rec mode” (➜page 52) is
set to “Off ”.
§3You cannot select the high speed mode when dubbing programs or
play lists from the HDD to a DVD-R that do not display the 
“”.
≥You will not be able to obtain better picture quality of the original
picture even if you select a higher quality picture mode than the
original. (Only prevents picture degradation.)
(h: hours, m: minutes)
∫Approximate SD card capacity and dubbing
capacity for SD VIDEO (MPEG4) programs
≥Using a Panasonic SD Memory Card.
≥
You cannot dub a program utilizing the maximum capacity of the card
due to the additional recording of copyright information etc.
≥The first value indicates video with non-rapid movement, the sec-
ond value indicates rapid movement.
∫When dubbing programs using high speed mode
to a high speed recording compatible DVD-R
≥When dubbing a Dolby Digital audio recording to 1k–4k high
speed recording compatible disc.
One Touch Dubbing
Dubbing direction and recording mode
Dubbing 
direction
Recording mode
High 
Speed§1XP– 
EP, 
FRHigh 
Speed
(MPEG4)High 
Speed
(MPEG2)MPEG2 
to 4§1§2
HDD ➜ RAM±± ±kk
➜ DV D - R±§3±kkk
➜ SDkk±k±
RAM ➜ HDD±
k±kk
➜ SDkk±k±
SD
CARD➜ HDD
kk±±k
➜ RAMkk±±k
Approximate recording times
Capacity
Recording mode
SF
(Super fine)F 
(Fine)N 
(Normal)E 
(Economy)
8 MB1 m
1 m2 m
2 m4 m
3 m9 m
8 m
16 MB2 m
2 m5 m
4 m9 m
6 m20 m
19 m
32 MB5 m
4 m10 m
9 m18 m
13 m43 m
41 m
64 MB10 m
8 m21 m
19 m38 m
28 m1 h 28 m
1 h 24 m
128 MB21 m
16 m43 m
40 m1 h 18 m
57 m2 h 58 m
2 h 50 m
256 MB42 m
32 m 1 h 26 m
1 h 19 m2 h 36m
1h 53 m5 h 56 m
5 h 40 m
512 MB1 h 24 m
1 h 5 m2 h 55 m
2 h 40 m5 h 16 m
3 h 49 m11 h 57m
11 h 26 m
1 GB2 h 43 m
2 h 6 m5 h 37 m
5 h 9 m10 h 7 m
7 h 21 m23 h 0 m
21 h 59 m
2 GB5 h 26 m
4 h 12 m11 h 14 m
10 h 19 m20 h 15 m
14 h 42 m46 h 1m
43 h 59 m
Recording mode and recording timeRequired timeSpeed
1 hour of recorded video using XP mode
15 minutes4k
2 hours of recorded video using SP mode 8k
4 hours of recorded video using LP mode 16k
6 hours of recorded video using EP mode 24k 
						

							32
RQT6986
Editing
Creating play lists
[HDD] [RAM]
Specify start and end points to create scenes, then specify the order
in which they are to be played. These scenes are not recorded sep-
arately so this doesn’t use much capacity.
You can create a maximum of 99 play lists and 999 scenes on a
DVD-RAM and HDD.
Preparation
≥Release protection (cartridge ➜page 10, disc➜page 44) before
proceeding.
≥Press [HDD] or [DVD] to select the drive.
1While stopped
Press [PLAY LIST].
2Press [3, 4] to select “Create PLAY
LIST” and press [ENTER].
3Press [ENTER] at the start point.
≥You can use basic functions like fast forwarding/rewinding
and slow-motion play (➜page 20).
≥You can use the skip function to jump to another program
(➜page 20).
4Press [ENTER] at the end point.
To specify another scene
Select “Next” and press [ENTER], then repeat steps 3 and 4.
5Press [3, 4] to select “Exit” and
press [ENTER].
The play list screen appears.
To clear the play list screen
Press [PLAY LIST].
To stop partway through
Press [RETURN].
[Note]
≥You cannot specify an end point before a start point.
≥
You may not be able to specify points within 3 seconds of each other.
≥Play pauses if the end of the last program on the disc is reached
during this procedure.
≥Depending on the state of recording, the actual number of play
lists that can be recorded may be less than that specified in this
manual.
≥You can high speed dub play lists created from recorded programs
to a DVD-R by switching “Rec in DVD-R high speed mode” to “On”
excluding the following cases.
–Play lists created from programs using a variety of recording
modes.
–Play lists created from multiple programs using “FR” recording
mode.
–Play lists mixed with a variety of audio types (Dolby Digital and
LPCM, etc.)
DV DTV
INPUT SELECTVCR Plus+OPEN/CLOSETV/VIDEO
CH
VOLUME
SKIP
DIRECT NAVIGATORPLAY LIST
TOP MENU
ENTER
MENU
FUNCTIONSRETURN
STOPPA U S EPLAY/x1.3
SLOW/SEARCH
CANCEL
123
DV D T V
4
56
789
0
100
FRAMECM SKIP TIME SLIP
ERASE
RECPROG/CHECKADD/DLT
DUBBINGREC MODESTATUSMARKER
AUDIOSETUPDISPLAYPOSITION
MEMORY
POWER
3, 4, 2, 1 
ENTER∫
RETURN
ERASE PLAY LIST
HDD DVDHDD, DVD
Numbered
buttons
PLAY LIST
------
Auto action USJ
01 10/23 006
006 0:03
02 10/26 0:07
03 10/21 0040:06
Dinosaur3
3
1
1
1
1
1
1
Create PLAY LIST
0   ~   9No.
RETURN ENTER
SELECT
NoDATE TOTALSCENEEDIT TITLE---
---------DVD
HDD:The location of 
the whole program’s 
start point
DVD-RAM:The loca-
tion of the whole 
disc’s start point
PLAY LIST
Creation
0 : 00 . 05StartEnd3
Start1
EndNextExit Scene No.
0 : 00 . 05
RETURN ENTER
SELECT
PLAY LIST No.4
PLAY01
-- : -- . --
DVD
PLAY LIST
Creation
0 : 00 . 05StartEnd
Start1
EndNextExit Scene No.
0 : 01 . 20
RETURN ENTER
SELECT
0 : 01 . 20
33
PLAY LIST No.4 
01
DVD
HDD:The location of 
the whole program’s 
end point
DVD-RAM:The
location of the whole
disc’s end point 
						

							33
RQT6986
Editing
1While stopped
Press [PLAY LIST].
2Press [3, 4] to select the play list
and press [ENTER].
≥To select with the numbered buttons:
e.g., “5”: [0] ➜ [5]
“15”: [1] ➜ [5]
All the scenes in the play list are played.
To stop play list play
Press [∫]. (The play list appears.)
1While stopped
Press [PLAY LIST].
2Press [3, 4] to select the play list
that contains the scene you want to
play and press [1].
3Press [3, 4] to select “Play Scenes”
and press [ENTER].
4Press [3, 4, 2, 1] to select the
scene and press [ENTER].
The scene you select is played.
To show scene 10 and later
Press [3, 4, 2, 1] to select “Next” and press [ENTER].
≥To select a page of scenes with the numbered buttons:
e.g., “5”: [0] ➜ [0] ➜ [5]
“15”: [0] ➜ [1] ➜ [5]
To stop scene play
Press [∫]. (The scene list appears.)
To clear the scene list
Press [RETURN].
1Press [ERASE].
A confirmation screen will be displayed.
2Press [2, 1] to select “Erase” or
“Yes” and press [ENTER].
[Note]
Even if you erase play lists or scenes the original program is not
erased.
Playing play lists
Playing play list scenes
PLAY LIST
------
USJ006 02 10/26 0:073
3
1
1
1
1
1
1
002003
004
001
--- -- --/-- --:--
NoDATE TOTALSCENEEDIT TITLE
Auto action03 10/21 0040:060   ~   9No.
RETURN ENTER
SELECT
DVD
01 10/23 0040:03Dinosaur
PLAY LIST
------
USJ006 02 10/26 0:073
3
1
1
1
1
1
1
002003
004
001
--- -- --/-- --:--
NoDATE TOTALSCENEEDIT TITLE
Auto action03 10/21 0040:06
DVD
01 10/23 0040:03DinosaurEdit Scenes
PL Copy
PL Erase
Enter Title
Properties
Play Scenes
RETURN ENTER
SELECT
PLAY LIST
Play Scenes
001 / 001
1 10/23 0:03 004 Dinosaur
Prev.
Next
001   00:00.19002003
004
------
------
---
0   ~   9Select Page
RETURN ENTER
SELECT
DVD
Page no./Total page no.
To erase a play list or a play list scene 
during playback 
						

							34
RQT6986
Editing
Editing play lists
[HDD] [RAM]
The play list is erased.
Properties
No.
Scenes 0:03.53Date
Total 1
00410/23/2002 FRI
RETURN
ENTER
Dinosaur
Erase this PLAY LIST?
Erase
Erase PLAY LIST
Cancel
RETURN
ENTERSELECT
Copy this PLAY LIST?
Copy
Copy PLAY LIST
Cancel
RETURN
ENTERSELECT
ENTER
_Enter Title
1 1
2
3
4
5
6
7
8
9
0
1002345
ABC a
DE F d
GH I
NOg
JKL j
M
m
67890
bcij
ef /l%
hifl$¢
&
klON@
n]_o[
SPACE
SETERASE
SELECT
0100PQRS p
TUV t
WX Y Z wqrs ( )
uv { }-
xyz
`^| 
! ?\
.
,

:
; ––
RETURN
π;
PLAY LIST
------NoDATE TOTALSCENEEDIT TITLE
USJ006 02 10/26 0:073
3
1
1
1
1
1
1
002003
004
001
-------/----:--
0   ~   9No.
RETURN ENTERSELECT03 10/21 0040:06
Dinosaur01 10/23 0040:03
Auto action
DVD
PLAY LIST
Edit Scenes
0   ~   9Select Page
001 / 001
  1 10/23 0:03 004 Dinosaur
  Prev. Next
AddMoveRe-editErase
RETURN ENTERSELECT---------
---
002003
004--- 001 00:00.19
DVD
INPUT SELECTVCR Plus+OPEN/CLOSETV/VIDEO
CH
VOLUME
SKIP
DIRECT NAVIGATORPLAY LIST
TOP MENU
ENTER
MENU
FUNCTIONSRETURN
STOPPA U S EPLAY/x1.3
SLOW/SEARCH
CANCEL
123
4
56
789
0
100
HDD DVDThe copied play list appears at 
the bottom of the list.
RETURN
3, 4, 2, 1ENTER Numbered 
buttons
PLAY
LISTHDD,
DVD
e.g., 
DVD-RAM
Once a play list has been erased, 
it is irretrievable. Check carefully 
before proceeding.
Play Scenes
Operation
While stopped
Press [PLAY LIST].
To clear the play list or scene 
list screen
Press [PLAY LIST].
To stop set up processPress [RETURN].
For your reference
You can only perform operations for 
“Play Scenes” and “Properties” if the 
disc is write-protected. Release 
protection 
(cartridge ➜ page 10, disc ➜ page 44) to access other items.Play list information (e.g., time and 
date) is shown.
Edit Scenes
Press [2, 1] to select 
the item (Add, Move, Re-
edit or Erase) and press 
[ENTER].
PL Copy
PL Erase
Enter Title
PropertiesPress [2, 1] to select 
“Erase
” and press 
[ENTER]. Press [2, 1] to select 
“Copy
” and press 
[ENTER].
➜ page 33, Playing play list scenes
Entering text ➜ page 46
Press [3, 4] to select 
the item and press 
[ENTER].Press [1] so the 
submenu appears.
To show scene 10 and later≥ Press [3, 4, 2, 1] to select “Next” and press [ENTER].
≥ You can also select a page of scenes  by entering a 3-digit   
   number with the numbered buttons.
   e.g.,       “5”:    [0] ➜ [0] ➜ [5]
                 “15”:  [0] ➜ [1] ➜ [5] Preparation
Press [HDD] or [DVD] to select the drive.
Press [3, 4] to select 
the play list.
≥ To create a new list, select
“Create PLAY LIST” and 
press [ENTER] (➜ page 32). 
						

							35
RQT6986
Editing
Repeat to erase other scenes.
∫ Erase ∫ Re-edit ∫ Move
Erase Scenes
Ye s N o Erase this scene?
RETURN
ENTERSELECT
001
PLAY LISTRe-edit Scenes
0 : 00 . 05StartEnd
Start
1
EndNextExit Scene No.0 : 02 . 08
RETURN ENTERSELECT
0 : 02 . 08
33
PLAY LIST No.3
01PLAYPrev.
DVD
PLAY LIST
Add Scenes
0 : 00 . 05StartEnd3
Start5
EndNextExit Scene No.0 : 00 . 05
RETURN ENTERSELECT
--:--.--
PLAY01
PLAY LIST No.3 DinosaurDVDPress [3, 4] to 
select “Exit
” 
and press 
[ENTER].
The new scene is 
inserted before the 
highlighted scene.
Press [3, 4] to select “Next
” and press [ENTER].
(Repeat to add other scenes.)
Repeat to move other scenes.
Press [3, 4, 2, 1] to select the place 
where you want to move the scene to 
and press [ENTER].
The scene is moved and inserted before the 
highlighted scene.
[Note]The play list itself is erased if 
you erase all the scenes in it.
∫ Add
Press [3, 4, 2, 1] 
to select the place
where you want to 
add the scene and 
press [ENTER].Press [ENTER] 
at the start point 
of the scene.Press [ENTER] 
at the end point 
of the scene.
Press [3, 4, 2, 1] 
to select the scene 
and press [ENTER].
Press [3, 4, 2, 1] 
to select the scene 
and press [ENTER].Press [ENTER] at 
the start point of 
the scene.
[Note]≥ You can use basic functions like fast forwarding/rewinding and slow-motion play (➜ page 20).
≥ You can use the skip function to jump to another program (➜ page 20).≥ You cannot specify an end point before a start point. 
≥ You may not be able to specify points within 3 seconds of each other.
≥ Play pauses if the end of the last program is reached during this procedure.
≥ You cannot edit still picture images.
≥ Depending on the state of recording, the actual number of play lists or scenes that can be recorded may be less than that specified 
in this manual.
≥ The picture illustration on the right may be shown in the HDD play list scene display.  
This picture illustration indicates pictures that are permitted to be recorded only once  
(➜ page 62, CPRM).
(maximum of 999 scenes)
Press [3, 4] to select “Prev.
” or “Next” and press 
[ENTER]. (Repeat to re-edit other scenes.)
Press [3, 4] to 
select “Exit
” 
and press 
[ENTER].
The re-edited 
scene replaces the 
old one.
Press [ENTER] 
at the end point 
of the scene.
Press [3, 4, 
2, 1] to select
the scene and
press [ENTER].
Once a scene has been 
erased, it is irretrievable. 
Check carefully before 
proceeding.Press [2, 1] to 
select “Yes
” and 
press [ENTER].
The selected scene is 
erased from the play 
list. 
						

							36
RQT6986
Editing
Editing programs
Protection
Ye sNo
Set up Program Protection.
RETURN
ENTERSELECT
Shorten
     Segment
– : – – . – –Start– : – – . – –End
StartEndNextExit
0 : 00 . 01
PLAY03
RETURN ENTERSELECT
N
S
Divide
     Program
– : – – . – –Divide
PreviewDivide
Exit
0 : 00 . 01
PLAY03
RETURN ENTERSELECT
N
S
Properties
No.
Date
CH1
6/20/ 2001 TUE
4On 1:02 PM
ENTER
Dinosaur
Time 0:01(SP)
RETURN
DIRECT NAVIGATOR
No DATECH TIME EDITTITLE
  9 : 00 PMAuto action026/20 WED63
3
1
1
1
1
1
11 : 00 PMUSJ036/20 WED13
ENTERRETURN0   ~   9No TOTAL 3SELECT
016/20 WED410 : 00 AMDinosaur
Erase Program
0 : 58 SP
Erase CancelCorresponding PLAY LIST will also be erased.Remaining Recording Time
RETURN
ENTERSELECT
ENTER
_Enter Title
Title on TOP MENU
(DVD-R)1 1
2
3
4
5
6
7
8
9
0
1002345
ABC a
DE F d
GH I
NOg
JKL j
M
m
67890
bcij
ef /l%
hifl$¢
&
klON@
n]_o[
SPACE
SETERASE
SELECT0100PQRS p
TUV t
WX Y Z wqrs ( )
uv { }-
xyz
`^| 
! ?\
.
,

:
; ––
RETURN
π;
DVD
DVD
DVD
INPUT SELECTVCR Plus+OPEN/CLOSETV/VIDEO
CH
VOLUME
SKIP
DIRECT NAVIGATORPLAY LIST
TOP MENU
ENTER
MENU
FUNCTIONSRETURN
STOPPA U S EPLAY/x1.3
SLOW/SEARCH
CANCEL
123
4
56
789
0
100
HDD DVD
Change
thumbnails
0 : 00 . 01Change3
Change thmubnails
Change
Exit
0 : 00 . 01
;03
RETURN ENTERSELECT
N
S
DVDChange thumbnails
Operation
Press 
[DIRECT NAVIGATOR].
Press [3, 4] to select 
the program.
≥ To select with the numbered  
buttons:
e.g., “5”:  [0] ➜ [5]
        ([HDD]  [0] ➜ [0] ➜ [5])
Press [1] so the 
submenu appears.
Press [3, 4] to select 
the item and press 
[ENTER].
To clear the program listPress [DIRECT NAVIGATOR].
To stop set up processPress [RETURN].
For your reference
You can only perform operations for 
“Properties” if the disc is write-
protected. Release protection
 (cartridge ➜ page 10, disc ➜ page 44) to access 
other items.
e.g., 
DVD-RAM
Preparation
Press [HDD] or [DVD] to select the drive.
RETURN
3, 4, 2, 1ENTER Numbered 
buttons
DIRECT
NAVIGATOR
HDD,
DVD
1
e.g., DVD-RAM
The program, and play lists 
created from it, are erased 
irretrievably when you use this 
procedure. Check carefully before 
proceeding.
Erase Program
Enter Title
Properties
[HDD] [RAM]
If set, this will protect the program 
from accidental erasure.
Shorten Segment
[HDD] [RAM] [DVD-R]
[HDD] [RAM] [DVD-R]
Program information (e.g., time and 
date) is shown.
Protection
The program segment, and play 
list scenes created from it, are 
erased irretrievably when you use 
this procedure. Check carefully 
before proceeding.
[HDD] [RAM]
Divide Program
[HDD] [RAM]
Select a point at which to divide the 
program into two.
Entering text ➜ page 46
You must be sure you wish to 
divide a program because once a 
program has been divided,
it cannot be returned to its 
original form.
Change thumbnails
[DVD-R]Select a thumbnail image of a title that 
is displayed in the top menu after 
finalizing.
Normally, the first scene of the program 
(after 1 second) is displayed. [HDD] 
[RAM] [DVD-R]
e.g., DVD-RAM 
						

							37
RQT6986
Editing0:19  SP Remaining Recording Time
Shorten Segment
Corresponding PLAY LIST will also be erased.
Erase Cancel
RETURN
ENTERSELECT
Shorten
     Segment
0 : 00 . 01Start– : – – . – –End3
StartEndNextExit
0 : 00 . 01
PLAY03
RETURN ENTERSELECT
N
S
0 : 00 . 01StartEnd3
StartEndNextExit
0 : 10 . 15
RETURN ENTERSELECT
0 : 10 . 15
N
SShorten
     Segment03
3
Divide Program
Divide Cancel
RETURN
ENTERSELECT
Once you divide the program,  
it will not be restored to the original.
DIRECT NAVIGATOR
No DATECH TIME EDITTITLE014
02 6
03
133
3
1
1
1
1
1
ENTER0   ~   9No TOTAL 3SELECTRETURN
  9 : 00 PMAuto action6/20 WED
11 : 00 PMUSJ6/20 WED6/20 WED 10 : 00 AM
Dinosaur
DVD
DVDDVD
[Note]≥ The disc’s available recording time may not increase after 
   erasing short programs.
≥ Computer data cannot be erased.
≥ The available recording time on DVD-R does not increase when 
    you erase programs.
The lock symbol 
appears when the 
program is write-
protected.
Press [2, 1] to set 
protection and press 
[ENTER].
[Note]≥ You can use basic functions like fast forwarding/rewinding and slow-motion  
play (➜ page 20).
≥ You can use the skip function to jump to another program (➜ page 20). 
≥ Play pauses if the end of the program is reached during this procedure.
≥ You may not be able to specify points within 3 seconds of each other.
≥ You cannot specify an end point before a start point. 
≥ You cannot specify points on still pictures in the program.
≥ The disc’s available recording time may not increase after erasing short segments.
[Note]≥ You can use basic functions like fast forwarding/ 
rewinding and slow-motion play (➜ page 20).
≥ You can use the skip function to jump to another 
program 
(➜ page 20). 
≥ The beginning and ending scenes cannot be 
set. Repeat to enter other sections.
Press [3, 4] to 
select “Exit
” and 
press [ENTER]. 
Press [2, 1] 
to select 
“Erase
” and 
press [ENTER]. 
Press [3, 4] to select “Next” and press [ENTER], then press [2, 1] 
to select “Erase” and press [ENTER].
Press [2, 1] to 
select “Erase
” and 
press [ENTER].
The program is erased.
Press [ENTER]  
at the end point  
of the section  
you want to 
erase.
Press [3, 4]  
to select “Exit
” 
and press 
[ENTER].
[Note]≥ You can use basic functions like fast forwarding/rewinding and slow-motion 
play (➜ page 20).
≥ You can use the skip function to jump to another program (➜ page 20). 
≥ The divided programs retain the title and CPRM property (➜ page 62) of 
the original program.
≥ 
Video and audio just before and after the dividing point may momentarily cut 
out.
≥ It is not possible to carry out Divide Program in the following cases:
   –when the program is extremely short.
   –when the total number of programs is more than 250 (HDD) or 99
     (DVD-RAM). To confirm the division point
Press [3, 4] to select “Preview” and press 
[ENTER]. (Play will begin from a point 10 
seconds prior to and after the division point.)
To change the division point
Restart play and press [3, 4] to select 
“Divide”, then  press [ENTER] at the point you 
want to change.
To change the thumbnail
Press [3, 4] to select “Change” and repeat the operation above.
Press [ENTER]  
at the point you 
want to divide  
the program.
Press [3, 4]  
to select “Exit
” 
and press 
[ENTER]. Press [ENTER] 
at the desired 
point to be the 
thumbnail. Press 
[ENTER] at 
the start point 
of the section 
you want to 
erase.
Press [1] (PLAY).Press [2, 1] to 
select “Divide
” and 
press [ENTER].
The program is divided. 
						

							38
RQT6986
Editing
Editing still pictures
JPEG
JPEG1/2INPUTSD card        100_PANA
Album
Slide Show
Copy
All copy of the card
RETURNENTERSELECT
ENTERRETURN
SELECT
INPUTJPEG
COPY
1 / 1Prev. Next--------
--------
----
000100020003
0004
FolderCopySD card           100_PANA
0   –   9 Select Page
ENTERRETURN
JPEG
INPUT
0   –   9  No
PC cardDVDHDD
SD card
\DCIM\@_PANASD card          100_PANA
100_PANA
101_DVD
           0043       0045
001
002
Picture 
File
3
3
RETURN
JPEG
ALL COPY
Copy all JPEG from the card.
Copy from
SD cardSD card
Copy toDVD
All copyCancel
ALL COPY OF THE CARD
\JPEG\DCIM001
SKIP
DIRECT NAVIGATORPLAY LIST
TOP MENU
ENTER
MENU
FUNCTIONSRETURN
STOPPA U S EPLAY/x1.3
SLOW/SEARCH
[HDD] [RAM] [SD] [CARD]
You can select the folder for 
editing. 
INPUT
To display still pictures (Album Display) ➜ page 22
Album
Copy Operation
e.g., SD card: First page
Slide Show
[SD] [CARD] !# [HDD] [RAM]
(maximum of 300 folders, 3000 files)
To display still pictures one by one with constant interval (Slide 
Show) ➜ page 23
[Note]≥ When there is no folder in the copying drive, a new folder will be created.
≥ When there is a folder in the copying drive, copying will continue from the last of the 
existing still pictures.
≥ When copying a folder, any files in the folder besides the still pictures are also copied.
≥ Folders lower than the folder to be copied will not be copied.
≥ If the space on the copying drive runs out or the number of files/folders to be copied 
exceeds the maximum, copying will stop partway through.
≥ If no title has been entered for the folder at the copying drive, the title from the copying 
source will be entered. It is recommended that the title is entered at the copying source.
≥ After copying, it may take some time to download the copying source information.
≥ Print (DPOF) number setting (➜ page 40) is not transferred.
All copy of the card
[SD] [CARD] # [HDD] [RAM]
(maximum of 300 folders, 3000 files)
[Note]≥ A new folder will be created in the copying drive.
≥ All compatible files in the folder are copied even if they are not still pictures, but non-
compatible files and folders will not be copied (➜ page 11).  
≥ Folders lower than the folder to be copied will not be copied.
≥ If the space on the copying drive runs out or the number of files/folders to be copied 
exceeds the maximum, copying will stop partway through.
≥ After copying, it may take some time to download the copying source information.
≥ Print (DPOF) number setting (➜ page 40) is not transferred.
To insert/remove the SD/PC card(➜ page 22) 
When the “SD” or “CARD” indicator in the 
unit display is flashing, the card is being 
read from or written to. Do not turn off the 
power or remove the card. Such action may 
result in malfunction or loss of the card’s 
contents.
To stop set up processPress [RETURN].
≥ You can also use [3, 4, 2, 1] to select 
“Cancel” or “No” and press [ENTER].
[Note]You can only perform operations for 
“INPUT”, “Album” and “Slide Show” if the 
disc or card is write-protected. Release the 
protection (cartridge or card ➜ page 10, 
folder ➜ page 40, disc ➜ page 44) to 
access other items.While stopped
Press [FUNCTIONS].
Press [3, 4, 2, 1] to 
select “JPEG” and press 
[ENTER].
Press [3, 4] to select 
the item and press 
[ENTER].
To select a folder other than the 
one currently being displayed  
➜ “INPUT”, right
Erase, Protect, Print (DPOF) ➜ page 40
Settings ➜ page 23, “To change the display timing”
 ➜ page 40, “Format”
FUNCTIONS
RETURN 3, 4, 2, 1
ENTER :, 9 
						

							39
RQT6986
Editing
0001
[Note]≥ “Picture” and “File” refer to numbers inside the 
folder selected. Lower files are not included.
≥When there are folders not displayed, use [:], 
[9] to switch between them. (➜ page 23, Folder 
structure).
Press [2, 1] to 
select “SD card” or 
“PC card”.   Press [3, 4] to highlight 
“Copy to” and press [2, 1] 
to select “HDD” or “DVD”.   Press [3, 4, 2, 1] to select “All 
copy” and press [ENTER].
All still pictures are copied, and ALL COPY 
screen reappears. To select all the still pictures in the folder
Press [3, 4, 2, 1] to select “Folder” and press [ENTER]. 
(A check mark appears on the folder’s name; check marks 
inputted separately will be erased.)
To erase check marks
Press [3, 4, 2, 1] to select the still picture or “Folder” with 
the check mark and press [ENTER].To select the copying drive
While the confirmation screen is displayed
1. Press [3, 4] to select “Destination” and press [ENTER].
2. Press [2] and [3, 4] to select the drive.
3. Press [1] and [3, 4] to select the folder and press [ENTER].
≥ Some folders cannot be copied to [➜ page 23, Folder structure 
(indicated by §)].
Press [3,4] to 
select still picture’s 
folder and press 
[ENTER]. Press [2] and 
[3,4] to select 
the drive and 
press [1].To enter the folder’s titleAfter selecting the still picture’s folder, press [1] to select “Folder 
Title” and press [ENTER].
(➜page 46, Entering text)
≥ If there is not enough space for the entry or if the limit for the 
number of files has  been exceeded (➜page 11, Still pictures), 
the title cannot be entered.
Select the 
copying 
drive.  
(➜ below)
Press [3, 4, 2, 1] 
to select “Copy” 
and press [ENTER].
Copying of still pictures 
begins.
Press [3, 4, 2, 1] 
to select “Copy” 
and press [ENTER].
A confirmation screen 
appears.
Press [3, 4, 2, 1] to select 
a still picture and press 
[ENTER]. 
A check mark appears 
on the still picture.
≥ Repeat this if you select more than 
one still picture. 
						

							40
RQT6986
Editing
Editing still pictures
Operation
JPEG
ENTERRETURN
SELECT
INPUTJPEG
ERASE
1 / 1Prev. Next--------
--------
----
000100020003
0004
FolderEraseSD  card         100_PANA
0   –   9Select Page
ENTERRETURN
SELECT
INPUTJPEG
PROTECT
1 / 1Prev. Next--------
--------
----
000100020003
0004
FolderSet UpCancelSD card          100_PANA
0   –   9Select Page
ENTERRETURN
INPUTJPEG
DPOF
1 / 1Prev.
Next--------
--------
----
000100020003
0004
WholeSet UpSD card          100_PANA
0   –   9Select Page
SELECT
JPEG2/2SD card          100_PANA
Erase
Protect
Print (DPOF)
Settings
RETURNENTER
SELECT
SKIP
DIRECT NAVIGATORPLAY LIST
TOP MENU
ENTER
MENU
FUNCTIONSRETURN
STOPPA U S EPLAY/x1.3
SLOW/SEARCH
[SD] [CARD] [HDD] [RAM]
Erase
[SD] [CARD] [HDD] [RAM]
You can set protection for whole 
folders or for individual still pictures.
Protect
Print (DPOF)
e.g., SD card: Second page
To insert/remove the SD/PC card
(➜ page 22) 
When the “SD” or “CARD” indicator in the 
unit display is flashing, the card is being 
read from or written to. Do not turn off the 
power or remove the card. Such action 
may result in malfunction or loss of the 
card’s contents.
To stop set up processPress [RETURN].
≥ You can also use [3, 4, 2, 1] to select 
“Cancel” or “No” and press [ENTER].
[Note]You can only perform operations for “Slide 
Show” in “Settings”  if the disc or card is 
write-protected. Release the protection 
(cartridge or card ➜ page 10, folder ➜ 
right, disc ➜ page 44) to access other 
items.
Settings
[SD] [CARD] 
You can select a whole folder or 
individual pictures for printing and 
specify the number of prints to be 
made (maximum 999 files).
[Note]≥ Settings cannot be made for folders and files not in accordance with DCF standards.
≥ Print settings (DPOF) made using this unit may not be viewable on other equipment.
≥ Settings cannot be made if there is no remaining space on the card.
≥ All settings made on other equipment, except the number of prints, will be canceled.
Slide Show
Format [Note]
When you erase folders, files other than still pictures in the folder are also erased. 
Folders lower than the folder to be erased will not be erased.
[SD] [CARD] 
You can erase all still pictures in the 
card and format an unformatted 
card.
Press [3, 4, 2, 1] to 
select “JPEG” and press 
[ENTER].
Press [3, 4] to select 
the item and press 
[ENTER].
To select a folder other than the 
one currently being displayed
➜ page 38, “INPUT”  While stopped
Press [FUNCTIONS].
≥ “INPUT”, “Copy” and “All copy of the card” ➜ page 38
≥ “Album” ➜ page 22, To display still pictures (Album Display)
≥ “Slide Show” ➜ page 23, To display still pictures one by one with constant 
interval (Slide Show)
[HDD] [RAM] [SD] [CARD]
To change the display timing
➜ page 23 FUNCTIONS
RETURN 3, 4, 2, 1
ENTER