Panasonic Dmp Ub900 Owners Manual

							Reference
31TQBA2018
¾BD-Video Secondary Audio
Select whether or not to mix the primary and 
secondary audio (including the button click 
sound).
If “Off” is selected, the unit outputs the primary 
audio only.
	≥ To enjoy BD-Video that supports Dolby Atmos® or 
DTS:XTMConnect this unit to an AV amplifier or similar device that 
supports it with an HDMI cable, and select the following 
settings:
– Dolby D/Dolby D +/Dolby TrueHD: “Bitstream”
– DTS/DTS-HD: “Bitstream”
– BD-Video Secondary Audio: “Off”
Dolby Atmos is a trademark of Dolby Laboratories.
∫ OPTICAL / COAXIAL Down Sampling
Select whether or not to convert the sampling 
frequency of the audio to be output from the 
OPTICAL/COAXIAL terminal.
If you choose to convert the sampling frequency, 
you can limit the maximum output to 48 kHz or 
96 kHz.
≥ Set a frequency supported by the connected 
device.
≥ When playing back BD-Video, signals are 
converted to 48 kHz despite the settings in the 
following cases:
– when the signals have a sampling frequency 
of 192 kHz
– when the disc has copy protection
– when “BD-Video Secondary Audio” is set to 
“On”
∫ Downmix
Select the downmix system of multi-channel to 
2-channel sound.
≥ Select “Surround encoded”, when the 
connected equipment supports the virtual 
surround function.
≥ The downmix effect is not available when 
“Digital Audio Output” is set to “Bitstream”.
≥ The audio will be output in “Stereo” in the 
following cases:
– AVCHD playback
– Playback of secondary audio (including the 
button click sound).
∫ HDMI Output Settings of Music Playback
Minimise the audio noise during music playback 
by automatically switching the video output to 
1080i.
∫ Settings for High Clarity Sound
Set a terminal that will stop processing audio 
signals or whether or not to turn on/off the unit’s 
display when “High Clarity Sound” ( >28) is set to 
“On (Video  Off)” or “On  (Video On)”.
≥ Set an option for video playback and audio 
playback.
∫ Audio Delay
Synchronization between picture and sound is 
corrected by adjusting the delay time of the audio 
output.
∫ Analog Multi Channel
Multi-channel surround sound is output from the 
AUDIO OUT terminals.
≥ If “On” is selected, audio will not be output from 
the HDMI OUT terminal.
– Speaker presence and size 
()
– Delay time ( )
– Channel balance ( )
To finish the speaker setting
Select “Complete”.
∫ 3D BD-Video Playback
Select the playback method of 3D compatible 
video software.
∫ 3D AVCHD Output
Select the output method of 3D AVCHD videos.
∫ 3D Playback Precautions
Set to display or hide the 3D viewing warning 
screen when playing back the 3D compatible 
video software.
3D
DMP-UB900_P-TQBA2018.book  31 ページ  ２０１６年６月８日　水曜日　午後４時４９分 
						

							32TQBA2018
∫Audio Language
Choose the language for audio.
≥ If “Original” is selected, the original language of 
each disc will be selected.
≥ When the selected language is not recorded on 
the disc, or depending on how the navigation is 
created on the disc, it may playback in a 
different language than the selected language.
≥ Enter a code ( >42) when you select “Other 
¢¢¢¢ ”.
∫Subtitle Language
Choose the language for the subtitle.
≥ When “Auto” is selected, a subtitle for the 
language selected in the “Audio Language” is 
displayed only when the language other than 
the language selected in the “Audio Language” 
is played back.
≥ When the selected language is not recorded on 
the disc, or depending on how the navigation is 
created on the disc, it may playback in a 
different language than the selected language.
≥ Enter a code ( >42) when you select “Other 
¢¢¢¢ ”.
∫Menu Language
Choose the language for the disc menus.
≥ Enter a code ( >42) when you select “Other 
¢¢¢¢ ”.
∫Subtitle Text
Select a desired item according to the language 
used for MKV subtitles text.
≥ This item is displayed only after playing back a 
file.
∫ On-screen Language
Choose the language for menus and on-screen 
messages.
∫ Closed Caption
Closed captioning services are dependent on 
contents, and the unit can display closed captions 
of both digital and analog types.
Press [OK] to show the following settings:
¾ Closed Caption Display
Set whether or not to display closed captions.
¾ Closed Caption Type
Select the closed caption type that matches the 
one of the content to be played back.
¾ Analog CC
Select the channel of analog closed captions.
¾ Digital CC
Select the channel of digital closed captions.
¾ Manual setting
Set the display style of closed captions.
¾ CC Reset
Restore the default “Closed Caption” settings.
∫ Easy Network Setting ( >17)
∫ Network Settings
Perform network-related settings individually.
Press [OK] to show the following settings:
¾ LAN Connection Mode
Select the LAN connection method.
≥ When not using wireless LAN (when turning it 
off), select “Wired”.
¾Wireless Settings
This allows the wireless router and connection 
settings to be set up. Current connection 
settings and connection state can be checked.
The wireless router connection wizard will be 
displayed.
Select a connection method to wireless access 
point.
Search for wireless network
WPS (PUSH button method)
WPS (PIN code method)
Manual setting
Language
Network
DMP-UB900_P-TQBA2018.book  32 ページ  ２０１６年６月８日　水曜日　午後４時４９分 
						

							Reference
33TQBA2018
¾IP Address/DNS Settings
This is for checking the state of the network 
connection and setting the IP address and 
DNS-related.
Press [OK] to show the respective setting.
¾ Proxy Server Settings
This is for checking the state of connection with 
the Proxy server and performing settings.
Press [OK] to show the respective setting.
¾ Network Service Settings ( >22)
Press [OK] to show the following settings:
Second Screen Browsing
When this function is set to “On”, you can 
enjoy the content you are viewing on a 
network service application of smartphone, 
etc. with the home network on the big screen 
of your TV.
Audio Auto Gain Control
Volume that is different depending on the 
contents is adjusted automatically to the 
standard volume while using the Network 
Service.
≥ Depending on contents, this function effect 
will not work.
≥ Select “Off” when the audio is distorted.
Time Zone
Set the unit’s time to match your location.
≥Some Network Service contents require the 
time zone to be set. Set time zone if 
necessary.
DST
Select “On” when using Daylight Saving time.
Notice
Displays the terms of service for the cloud 
services.
¾Network Drive Connection
This unit can access a hard disk shared folder 
on a network and play back videos, still 
pictures, and music.
¾ Remote Device Settings ( >24)
Press [OK] to show the following settings:
Remote Device Operation
Enable to operate the unit by DMC.
Setting Unit Name
Set the name of this unit to be displayed on 
the connected equipment.
Registration Type
Remote Device List
Registering/deregistering of the displayed 
equipment can be performed when “Manual” 
in “Registration Type” is selected.
¾ BD-Live Internet Access ( >21)
You can restrict Internet access when BD-Live 
functions are used.
≥ If “Allow ( Limited )” is selected, Internet 
access is permitted only for BD-Live contents 
which have content owner certificates.
The following items use the same password.
Don’t forget your password.
∫ DVD-Video Ratings
Set a ratings level to limit DVD-Video play.
∫ BD-Video Ratings
Set an age limit of BD-Video (including Ultra HD 
Blu-ray) play.
∫ Network Service Lock
You can restrict the usage of Network Service.
Auto
Allow connections to all 
the equipment accessing 
this unit.
Manual
Set the permission for 
individual equipment 
connections accessing this 
unit.
Ratings
DMP-UB900_P-TQBA2018.book  33 ページ  ２０１６年６月８日　水曜日　午後４時４９分 
						

							34TQBA2018
∫Easy Setting
You can execute basic settings.
∫ Display Settings
Press [OK] to show the following settings:
¾ Screen Saver Function
This is to prevent image retention on the 
screen.
≥ When this is set to “On”:
If a list of playback content is displayed and 
there is no operation for 5 minutes or more, 
the screen switches to HOME menu 
automatically.
≥ While playing and pausing, etc., this function 
is not available.
¾Status Messages
Choose whether to show status messages 
automatically.
¾ VIERA Link
Set to use “VIERA Link” function when 
connected via HDMI cable to a device that 
supports “VIERA Link”.
≥ Select “Off” when you do not want to use 
“VIERA Link”.
∫ Front Panel Display
Changes the brightness of the unit’s display.
This setting is also able to switch by pressing 
[DIM].
≥ If “Auto” is selected, the display is set to bright 
and only dimmed during playback.
≥ This setting does not work when “Front Panel 
Display” in “Settings for High Clarity Sound” is 
set to “Off”. ( >31)
(Except for when “High Clarity Sound” is set to 
“Off”)
∫ Quick Start
Speed of start-up from standby mode is 
increased.
≥ When set to “On”, the internal control unit will be 
powered. The idle power consumption will 
increase so compared to when set to “Off”.
∫ Remote Control Code
Change the remote control code if other 
Panasonic products react to this remote control.
∫ Firmware Update ( >18)
Press [OK] to show the following settings:
¾ Automatic Update Check
When this equipment remains connected to the 
Internet, it will check for the latest firmware 
version when it is turned on and you can update 
it if necessary.
¾ Update Now
You can update the firmware manually if a 
firmware update is available.
∫ System Information
Press [OK] to show the following settings:
¾ License
Information about the software used by this unit 
is displayed.
¾ Firmware Version Information
Display firmware version of this unit and 
wireless LAN module.
∫ Restore Default Settings
This returns all values in the Setup menu and the 
Option menu to the default settings, except for 
some settings of network, ratings, remote control 
code, on-screen language, etc.
System
DMP-UB900_P-TQBA2018.book  34 ページ  ２０１６年６月８日　水曜日　午後４時４９分 
						

							Reference
35TQBA2018
Troubleshooting guide
Before requesting service, please perform the 
following checks.
The following do not indicate a problem with 
this unit:
– Regular disc rotating sounds.
– Image disturbance during search.
– Image disturbance when replacing 3D discs.
∫Unit does not respond to remote 
control or unit’s buttons.
Touch and hold [ Í/I] on the main unit for 
3 seconds.
– If still unable to turn the unit off, disconnect the  AC power supply cord, wait 1 minute, then 
reconnect the AC power supply cord.
∫ The buttons of the unit do not 
work.
Touch the buttons with your finger. They may not 
work if operated with your fingernails or hands 
wearing gloves.
∫The buttons of the unit are 
sensitive.
The buttons of the unit respond to light touch. Do 
not place objects on or around them.
∫Cannot eject disc.
1 While the unit is off
Press and hold [OK], the yellow button and 
the blue button on the remote control at the 
same time for more than 5 seconds.*
– “00 RET” is displayed on the unit’s display.
2 Press [ 1] (right) repeatedly on the remote 
control until “06 FTO” is displayed on the 
unit’s display.
3 Press [OK].
* Perform this operation when the light on the remote control 
button is turned off. ( >8, [LIGHT])
To return to the factory default.
¾ Select “Yes” in “Restore Default Settings” in 
the Setup menu. ( >34)
To return all settings to the factory preset.
¾ Reset the unit as follows:
1 While the unit is off
Press and hold [OK], the yellow button and 
the blue button on the remote control at the 
same time for more than 5 seconds.*
– “00 RET” is displayed on the unit’s display.
2 Press [ 1] (right) repeatedly on the remote 
control until “08 FIN” is displayed on the unit’s 
display.
3 Press and hold [OK] for more than 5 seconds.
* Perform this operation when the light on the remote control 
button is turned off. ( >8, [LIGHT])
This unit is turned off when the input for the 
TV is switched.
¾ This is a normal phenomenon when using 
VIERA Link. For details please read the 
owner’s manuals for the TV.
The remote control doesn’t work properly.
¾Change the batteries in the remote control. 
(> 5)
¾ The remote control and this unit are using 
different codes.
If “SET CODE ” is displayed on the unit’s 
display when a button is pressed on the 
remote control, change the code on the 
remote control.
Press and hold [OK] and the displayed 
number (“ ”) for more than 5 seconds.
This unit is turned off automatically.
¾ To save on electricity, this unit is turned off 
automatically depending on the media if there 
is no button operation for about 20 minutes 
when not playing back (such as when paused 
or displaying the menu, displaying still 
pictures, etc.).
Do you have the latest firmware installed?
Panasonic is constantly  improving the unit’s 
firmware to ensure that our customers are 
enjoying the latest technology. ( >18)
4
Make the following checks and visit our 
website for more information.
http://shop.panasonic.com/support
Enter the model number.
4
Or visit our website to find a service center.
You can find a service  center near you easily 
on our website.
Other support information :
“Limited Warranty” (>45).
General operation
DMP-UB900_P-TQBA2018.book  35 ページ  ２０１６年６月８日　水曜日　午後４時４９分 
						

							36TQBA2018
You have forgotten your ratings password.
You want to cancel the ratings level.
¾The ratings level returns to the factory 
defaults.
1 While the unit is on
Press and hold [OK], the yellow button and 
the blue button on the remote control at the 
same time for more than 5 seconds.*
– “00 RET” is displayed on the unit’s display.
2 Press [ 1] (right) repeatedly on the remote 
control until “03 VL” is displayed on the unit’s 
display.
3 Press [OK].
* Perform this operation when the light on the remote control 
button is turned off. ( >8, [LIGHT])
The TV screen turns black.
¾ In the following cases, HDMI authentication 
takes place and a black screen is displayed:
– When “24p Conversion” is set to “On”.
– When “24p Output” is set to “Auto”.
– When the display is switched between 2D 
and 3D images.
– When you quit the 4K playback by 
displaying another screen, including the 
HOME menu.
– When “HDMI Output Settings of Music 
Playback” is set to “Sound Quality Priority”.
This unit does not recognize the USB 
connection correctly.
¾ Disconnect and re-connect the USB cable. If 
it still does not recognize the connection, turn 
this unit off and on again.
¾ USB devices may not be recognized by this 
unit when connected using the following :
– a USB hub
– a USB extension cable
¾ If you connect USB HDD to this unit, use the 
USB cable that is supplied with the HDD.
¾ If the USB HDD is not recognized, the power 
to the USB HDD may not be supplied. Supply 
power from an external source.
Images from this unit do not appear on the TV 
screen, or they are distorted.
¾An incorrect resolution is selected in 
“Resolution”. Reset the setting as follows:
1 While the unit is on
Press and hold [OK], the yellow button and 
the blue button on the remote control at the 
same time for more than 5 seconds.*
– “00 RET” is displayed on the unit’s display.
2 Press [ 1] (right) repeatedly on the remote 
control until “04 PRG” is displayed on the 
unit’s display.
3 Press and hold [OK] for more than 5 seconds.
Set the item again. ( >29)
– When Dolby Digital Plus, Dolby TrueHD, 
and DTS-HD
® audio are not output properly, 
select “Yes” in “Restore Default Settings” 
( > 34) and make proper settings.
¾ The connected devices  are changed. Reset 
the setting as follows:
1 While the unit is on
Press and hold [OK], the yellow button and 
the blue button on the remote control at the 
same time for more than 5 seconds.*
– “00 RET” is displayed on the unit’s display.
2 Press [ 1] (right) repeatedly on the remote 
control until “13 L4K” is displayed on the unit’s 
display.
3 Press and hold [OK] for more than 5 seconds.
– “4K60p Output” will be set to “Off”. Make 
the correct setting again. ( >29)
* Perform this operation when the light on the remote control 
button is turned off. ( >8, [LIGHT])
¾ When “3D BD-Video Playback” in the Setup 
menu is set to “Auto”, images may not be 
output depending on the connection method. 
After removing the disc from this unit, select 
“Set before play” in the Setup menu, and 
select “2D Playback” in the setup screen 
displayed when playing 3D discs. ( >31)
¾ When outputting in 4K, images may be 
distorted depending on the HDMI cable. Use 
an HDMI cable that supports 18 Gbps.
Picture
DMP-UB900_P-TQBA2018.book  36 ページ  ２０１６年６月８日　水曜日　午後４時４９分 
						

							Reference
37TQBA2018
Video is not output.
¾Video is not output when the “High Clarity 
Sound” is set to “On (Video Off)”. ( >28)
¾ Video from the HDMI AUDIO OUT terminal is 
not output when the “HDMI(AUDIO) Output 
Mode” is set to “Audio Only”. ( >29)
Video is not output in 4K or high-definition.
¾ Confirm that “Resolution” in the Setup menu 
is set properly. ( >29)
¾ Confirm the HDMI cable, related connections 
and the compatibility of TV video input.
To output images in 4K, connect the HDMI 
cable to a 4K compatible terminal of the 
connected device. ( >10)
¾ Set “HDMI(AUDIO) Output Mode” to “Audio 
Only”. ( >29)
¾ To enjoy image in 4K/60p, set “4K60p Output” 
to “4K/60p(4:4:4)” or “4K/60p(4:2:0)”. ( >29)
¾ If “4K60p Output” is set to “4K/60p(4:4:4)”, 
check to see if the connected HDMI cable 
supports 18 Gbps. ( >10, 29)
¾ If 4K images are not output from the 
connected 4K-compatible TV, set “4K60p 
Output” to “4K/60p(4:4:4)” or “4K/60p(4:2:0)”. 
(>29)
3D video is not output.
¾ Connect to a 3D compatible device (e.g., TV 
and amplifier/receiver).
¾ When a non-3D compatible amplifier/receiver 
is connected between this unit and a TV, 3D 
video is not output. ( >13)
¾ If there is a non-3D compatible amplifier/
receiver connected to the HDMI AUDIO OUT 
terminal, set the “HDMI(AUDIO) Output 
Mode” to “Audio Only”. ( >29)
¾ Confirm the settings on this unit and the TV 
for 3D. ( >21)
3D video is not output correctly as 2D.
¾ Select “Set before play” in the Setup menu, 
and select “2D Playback” in the setup screen 
displayed when playing 3D discs. ( >31, “3D 
BD-Video Playback”)
¾ Discs that have recorded titles with Side by 
side (2 screen structure) and that can be 
enjoyed in 3D are played back in accordance 
with the settings of the TV.
No subtitles.
¾When progressive output is on, closed 
captions/subtitles cannot be displayed.
The subtitles overlap closed captions 
recorded on discs.
¾Turn off the subtitles or the closed captions.  
( > 26, 27, 32)
Closed captions are not displayed.
¾ Confirm that the source content supports CC.
¾ Confirm the “Closed Caption Display” is set to 
“On”.  (> 27, 32)
¾ Change the “Closed Caption Type” setting. 
(> 27, 32)
¾ Confirm the “Analog CC” or “Digital CC” is set 
properly  (> 27, 32).
A black band is displayed around the edge of 
the screen.
The aspect ratio of the screen is abnormal.
¾ Adjust the aspect setting on the TV.
There is a lot of image lag when playing video.
¾Set “0” all items in the “Noise Reduction”. 
(> 27)
¾ Set “Audio Delay”. ( >31)
Cannot hear the desired audio.
¾ Check the connections and the “Digital Audio 
Output” settings. ( >11, 30)
¾ When the unit is connected to an amplifier/
receiver with the 7.1ch AUDIO OUT 
terminals, set “Analog Multi Channel”. ( >31)
¾ To output audio from a device connected with 
an HDMI cable, set “Audio Output” to “On” in 
the Setup menu. ( >30)
¾ When connecting this unit to a TV via an 
HDMI VIDEO OUT and to an amplifier/
receiver via an HDMI AUDIO OUT, set 
“HDMI(VIDEO) Output Mode” to “Auto ( Video 
Only / Video+Audio )”. ( >11, 29)
Audio
DMP-UB900_P-TQBA2018.book  37 ページ  ２０１６年６月８日　水曜日　午後４時４９分 
						

							38TQBA2018
There is no sound coming out.
¾To output audio using DIGITAL AUDIO OUT 
terminal, set “OPTICAL / COAXIAL Down 
Sampling” properly. ( >31)
¾ Refer to “Connecting to an amplifier/receiver” 
(>11 - 15) to check the audio output settings 
suited to the connections of your device.
In the following cases, audio is not output 
from the terminals listed below:
≥ HDMI VIDEO OUT terminal
– When a device is connected to the HDMI 
AUDIO OUT terminal and “HDMI(VIDEO) 
Output Mode” is set to “Auto ( Video Only / 
Video+Audio )” ( >29)
– When “Audio Output” in “Advanced  Settings” is set to “Off” ( >30)
– While playback is being performed with 
“Audio Output” in “Settings for High Clarity 
Sound” set to “OPTICAL / COAXIAL Only” 
or “Analog Only” ( >31)
– When “Analog Multi Channel” is set to “On”  (> 31)
≥ HDMI AUDIO OUT terminal
– When “Audio Output” in “Advanced 
Settings” is set to “Off” ( >30)
– While playback is being performed with 
“Audio Output” in “Settings for High Clarity 
Sound” set to “OPTICAL / COAXIAL Only” 
or “Analog Only” ( >31)
– When “Analog Multi Channel” is set to “On”  (> 31)
≥ OPTICAL/COAXIAL terminal
– When a device is connected to the HDMI 
AUDIO OUT terminal and “Audio Output” in 
“Advanced Settings” is set to “On” ( >30)
– While playback is being performed with  “Audio Output” in “Settings for High Clarity 
Sound” set to “HDMI Only” or “Analog Only” 
(> 31)
≥ 2ch AUDIO OUT terminals
– When a device is connected to the HDMI 
AUDIO OUT terminal and “Audio Output” in 
“Advanced Settings” is set to “On” ( >30)
– While playback is being performed with 
“Audio Output” in “Settings for High Clarity 
Sound” set to “HDMI Only” or “OPTICAL / 
COAXIAL Only” ( >31) ≥
7.1ch AUDIO OUT terminals
– While playback is being performed with 
“Audio Output” in “Settings for High Clarity 
Sound” set to “OPTICAL / COAXIAL Only” 
(> 31)
– When “Analog Multi Channel” is set to “Off” 
(> 31)
Disc cannot be played.
¾ The disc is dirty. ( >5)
¾ The disc is not finalized. ( >7)
¾ Depending on the Ultra HD Blu-ray disc, it 
may not be possible to perform playback 
unless this unit is connected to the Internet.
Still pictures (JPEG) do not play back 
normally.
¾The images that were edited on the PC, such 
as Progressive JPEG, etc., may not be played 
back.
I can’t play back BD-Live.
¾The SD card is write-protected. ( >7)
¾ Confirm that this unit is connected to the 
broadband Internet. ( >16)
¾ Confirm the “BD-Live Internet Access” 
settings. ( >33)
¾ Confirm an SD card is inserted into the SD 
card slot. ( >9)
I can’t connect to the network.
¾ Confirm the network connection and settings. 
(> 16, 17, 32)
¾ There may be interference that prevents the 
unit from detecting your home network. Place 
the unit and the wireless router closer to each 
other. This unit may be able to detect your 
network name ( >18, “SSID”).
¾ Check the owner’s manuals for each device 
and connect accordingly.
Playback
Network
DMP-UB900_P-TQBA2018.book  38 ページ  ２０１６年６月８日　水曜日　午後４時４９分 
						

							Reference
39TQBA2018
When using wireless LAN connection, video 
from the DLNA Certified media server is not 
played back or video frames are dropped 
during playback.
¾
Higher transfer rate router such as 802.11ac or 
11n (2.4 GHz or 5 GHz) wireless router may 
solve the problem. If you use 802.11ac or 11n 
(2.4 GHz or 5 GHz) wireless router, it is 
necessary to set the encryption type to “AES”.
Simultaneous use with a microwave, cordless 
telephone etc. at 2.4 GHz may result in 
connection interruptions or other problems.
¾On the “Wireless Settings” screen ( >32), the 
continuous lighting of at least 4 “Reception” 
indicators is the target for a stable connection. 
If 3 or fewer indicators are lit or the 
connection is being interrupted, change the 
position or angle of your  wireless router and 
see if the connection state improves. If there 
is no improvement, connect to a wired 
network and perform the “Easy Network 
Setting” ( >17) again.
Cannot read. Please check the disc.
¾ You inserted an incompatible disc. (Video CD, 
etc.)
Cannot play.
¾You inserted an incompatible disc (Discs 
recorded in PAL video, etc.).
Cannot play this title.
¾You tried to play a non-compatible video.
No disc inserted.
¾The disc may be upside down.
$ This operation is not available.
¾ Some operations are unsupported by the unit. 
(For example, reverse slow motion, etc.)
IP address is not set.
¾The “IP Address” in “IP Address/DNS 
Settings” is “---. ---. ---. ---”. Set the “IP 
Address”, “Subnet Mask”, and “Default 
Gateway”. (Select the automatic address 
acquisition if necessary.)
The current wireless network security setting 
is weak. It is recommended to change to a 
stronger security setting.
¾Set a stronger network security level referring 
to the wireless router owner’s manuals.
F99
¾The unit fails to operate properly. Touch [ Í/I] 
on the main unit for 3 seconds to switch the 
unit to standby, then switch back on.
NET
¾ While connecting to a network.
NO PLAY
¾There is a viewing restriction on a BD-Video 
or DVD-Video. ( >33)
¾ A DVD-Video disc with an incompatible color 
encoding system or region code is inserted.
NO READ
¾The media is dirty or badly scratched. The 
unit cannot play.
REMOVE
¾The USB device is drawing too much power. 
Remove the USB device.
SET CODE 
(“    ” stands for a number.)
¾ The remote control and this unit are using 
different codes. Change the code on the 
remote control.
Press and hold 
[OK] and the 
indicated number 
button at the same time for more than 
5 seconds.
U59
¾Temperature of this unit is hot and the unit 
switches to standby for safety reasons.
Wait for about 30 minutes.
Install or place this unit with good ventilation.
START
¾A firmware update will start. Please do not 
turn off the unit.
UPDATE  /5
(“    ” stands for a number.)
¾ A firmware update is in progress.
Please do not turn off the unit.
FINISH
¾The firmware update is complete.
Messages on the screen
Messages on the unit’s 
display
DMP-UB900_P-TQBA2018.book  39 ページ  ２０１６年６月８日　水曜日　午後４時４９分 
						

							40TQBA2018
Specifications
≥Specifications are subject to change without notice.
General
Signal system NTSC
Operating temperature 
rangei5
oC to i35 oC
(i41 oF to i95oF)
Operating humidity 
range  10 % to 80 % RH 
(no condensation)
AUDIO OUT (Pin jack) Analog Audio output (L/R, 
7.1ch):
Standard : 0.5 Vrms,
Full scale : 2.0 Vrms at 1 kHz 
(