Panasonic Dmp Bd60 Operating Instructions

							RQT9378
41
On the unit’s displayPage
F99≥The unit fails to operate properly. Press [POWER  Í/I] on the main unit to switch 
the unit to standby for 3 seconds. Now press [POWER  Í/I] on the main unit 
again to turn the unit on. —
HDMI ONLY
≥Some BD-Video discs can only be output with HDMI. —
NET≥Displays while VIERA CAST is starting up. —
No PLAY≥There is a viewing restriction on a BD-Video or DVD-Video. 32
No READ≥The media is dirty or badly scratched. The unit cannot play. —
PLEASE WAIT≥The unit is carrying out internal process. This is not a malfunction. You cannot 
operate the unit while “PLEASE WAIT” is displayed.
≥When connected to TV(VIERA) with HDAVI Control 4, and power supply is turned 
off by the “Auto power stand-by” function on the TV side. —
—
REMOVE
≥The USB device is drawing too much power. Remove the USB device. 19
SET 
(“    ” stands for a number.) ≥The remote control and main unit are using different codes. Change the code on 
the remote control.
Press and hold [OK] and the indicated number button at the 
same time for more than 5 seconds. 36
UNFORMAT
≥You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL 
or DVD-RW (DVD-Video format). —
UNSUPPORT
≥You have inserted a media the unit cannot play.
≥You tried to operate with a non-compatible USB device. 6, 7
7
U59 ≥The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until 
the message disappears.
Select a position with good ventilation when installing the unit. Do not block the 
cooling fan on the rear of the unit. —
U72
U73
≥The HDMI connection acts unusually.
–The connected equipment is not HDMI compatible.
–Please use HDMI cables that have the HDMI logo (as shown on the cover).
–The HDMI cable is damaged. —
H
  or F ≥There is something unusual. (The service number displayed after H and F 
depends on the unit’s condition.)
≥Check the unit using the troubleshooting guide. If the service number does not 
disappear, do the following.
1 Disconnect the plug from the AC outlet, wait a few seconds, then reconnect it.
2 Press [POWER  Í/I] to turn the power on. (The unit may be fixed.)
If the service number does not disappear despite doing the above, request 
service from the dealer. Inform the dealer of the service number when requesting 
service. —
42–44
START ≥The system is being restarted during the firmware update. Please do not turn off 
power. 16
UPD
/ ≥The firmware is being updated. 16
FINISH≥The firmware update is complete. 16
Reference
RQT9378~Body_mst.fm  41 ページ  ２００８年１２月２５日　木曜日　午後３時２４分 
						

							RQT9378
42
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart 
do not solve the problem, refer to “Custome r Services Directory (United States and Puerto Rico)” on page 46 if you reside in th e U.S.A.and Puerto 
Rico, or refer to “Product information” on page 48 if you reside in Canada.
The following do not indicate a problem with this unit:≥ Regular disc rotating sounds.
≥ Image disturbance during search.
To reset this unit Page
Power
Operation
To restore the unit if it 
freezes due to one of the 
safety devices being 
activated≥Press and hold [POWER  Í/I] on the main unit for 3 seconds. (The settings remain 
unchanged.)—
To return all settings to the 
factory preset
≥Select “Yes” in “Restore Default Settings” in the Setup menu.
This returns all values in the Setup menu and the on-screen menu, except for “Remote 
Control Code”, “On-screen Language”, “IP Address/DNS Settings”, “Proxy Server 
Settings”, “DVD-Video Ratings”, “BD-Video Ratings” and “Network Service“ to the 
default settings.36
To return to the factory 
preset
(No setting)≥Reset the unit as follows: 1Press [POWER  Í/I] on the unit to turn off the unit.
2 Press and hold [ ;], [POWER Í/I] and [
						

							RQT9378
43
TV screen and videoPage
Sound
The images from this unit 
do not appear on the 
television.
Picture is distorted.
Jittering occurs.≥Make sure that the television is connected to either the VIDEO OUT terminal,  COMPONENT VIDEO OUT terminals or HDMI AV OUT terminal on this unit.
≥Make sure that the television’s input setting (e.g., VIDEO 1) is correct.
≥An incorrect resolution is selected in “Component Video Resolution”, when the 
television is connected to COMPONENT VIDEO OUT terminals. While stopped, 
press and hold [∫ ] and [1] (PLAY) on the main unit at the same time for more 
than 5 seconds to cancel this setting. Set the item again.
≥If “24p Output” is set to “On” when the unit is connected to a TV through any terminal other 
than HDMI, images may not display properly. In this case, set “24p Output” to “Off”.
≥When “24p Output” is set to “On”, HDMI authentication takes place where 24p 
images switch to other images, and a black screen is displayed.
≥When “24p Output” is set to “On”, jittering may occur while playing DVD-Video  other than 24p images. In this case, turn “24p Output” to “Off”.
≥[DivX] : Images may not be output due to how files were created.
≥An incorrect resolution is selected in “HDMI Resolution”, when the television is 
connected to HDMI AV OUT terminals. While stopped, press and hold [ ∫] and 
[ 1
](PLAY) on the main unit at the same time for more than 5 seconds to cancel 
this setting. Set the item again. However, Dolby Digital Plus, Dolby TrueHD, and 
DTS-HD audio are not output in bitstream. To output the bitstream, select “Restore Default 
Settings” to restore the factory presets and make proper settings.
≥Picture may not be seen when more than 4 devices are connected with HDMI  cables. Reduce the number of connected devices.
11
—
34
34
34
34
—
36
—
The screen changes 
automatically.
≥When the “Screen Saver Function” in the Setup menu is set to “On”, the display may return 
to the screen saver mode automatically if there is no operation for 10 minutes or more.33
Video is not output .≥An image is not output from the COMPONENT VIDEO OUT terminal or the 
VIDEO OUT terminal when the “High Clarity Sound” is enabled. Set the “High 
Clarity Sound” in the on-screen menu to “Off” to use the COMPONENT VIDEO 
OUT terminal or the VIDEO OUT terminal.31
Video is not output in high 
definition. ≥High definition video cannot be output through the VIDEO OUT terminals.
≥Confirm that the “HDMI Video Mode”, “HDMI Resolution”, and “Component Video 
Resolution” in the Setup menu are set properly.  —
34
The 4:3 aspect ratio picture 
expands left and right.
Screen size is wrong.≥Use the television to change the aspect. Refer to your television’s operating instructions.≥When using a component video cable, set “Progressive” to “Video”. If the situation 
is not restored after that, set “TV Aspect” to “4:3 Pan & Scan”.
≥When using an HDMI cable, change “TV Aspect” type to “16:9”.—
31, 34
34
There is a lot of after-image 
when playing video. ≥Turn “3D NR” or “Integrated NR” off if it is on.
31
When playing DVD-Video using 
progressive output, one part of 
the picture momentarily 
appears to be doubled up.≥When you use the HDMI AV OUT terminal for video output, follow the steps below for setting.1 Connect this unit to the TV with any cable except the HDMI cable.
2 When you connect with the Component Video cable, set “HDMI Video Mode” to 
“Off” and “Component Video Resolution” to “480i” in the Setup menu.34
Still pictures (JPEG) do not 
play back normally. ≥The images that were edited on the PC, such as Progressive JPEG, etc., may not 
play back. 38
No sound.
Low volume.
Distorted sound.
Cannot hear the desired 
audio type.≥Check the connections and the “Digital Audio Output” settings. Check the input 
mode on the amplifier/receiver if you have connected one.
≥Press [AUDIO] to select the audio. 
≥[BD80] : When the unit is connected to an amplifier/receiver with the AUDIO OUT 
terminal, set “Analog Audio Output” and match multi channel speaker settings. If 
these are not set properly, the audio is not output correctly.
≥
[BD80]: When connected to an amplifier/receiver or any other devices using both 
AUDIO OUT terminal and HDMI AV OUT terminal, the audio from AUDIO OUT 
terminal may not be output with the desired audio depending on the specifications 
of the connected devices, etc. Set “HDMI Audio Output” to “Off”, when you output 
multi-channel surround sound from AUDIO OUT terminal.
≥The sound effects (Re-master, V. Surround, etc.) will not work when the bitstream signal is 
output from the HDMI AV OUT terminal or the DIGITAL AUDIO OUT terminal.
≥[DivX] : Audio may not be output depending on how files were created.
≥Audio may not be heard when more than 4 devices are connected with HDMI  cables. Reduce the number of connected devices.
≥To output audio from a device connected with an HDMI cable, set “HDMI Audio  Output” to “On” in the Setup menu.
11–13, 33
21
34, 37
34
—
—
—
34
Cannot switch audio. ≥There are discs for which audio cannot be changed because of how the disc was 
created.
≥When connecting an amplifier/receiver using a coaxial cable ([BD80]), optical digital audio 
cable or an HDMI cable, you cannot switch the audio if “Dolby D/Dolby D +/Dolby TrueHD” 
or “DTS/DTS-HD” is set to “Bitstream”. Set “Dolby D/Dolby D +/Dolby TrueHD” or “DTS/
DTS-HD” to “PCM” or connect using AUDIO OUT terminal.
—
12
, 13, 33
Reference
RQT9378~Body_mst.fm  43 ページ  ２００８年１２月２４日　水曜日　午後６時２８分 
						

							44
RQT9378
Troubleshooting guide
CardPage
USB
Network
Other difficulties with playback
The capacity of the SD card 
decreased.≥When a BD-Video that supports BD-Live is used, and an SD card is in the slot,  data may be written to the SD card. 22
Music on an SD card cannot 
be played. ≥Data that can be played from an SD card are AVCHD, MPEG2 and JPEG data. 
7
The contents of the card 
cannot be read.≥The card is not compatible or the contents on the card may be damaged.
≥Turn off and then turn on the unit again.7
—
The contents of the USB 
device cannot be read.≥Remove the USB device from the USB port and then insert again. If this does not  solve the problem, turn off and turn on the unit again.
≥Check that the USB device is inserted correctly.
≥The format of the USB device or of its contents is not compatible with the unit.  (The contents on the USB device may be damaged.)
≥The USB device contains a folder structure and/or file extensions that are not  compatible with this unit.
≥Turn off and then turn on the unit again.
≥USB devices connected using a USB extension cable or a USB hub may not be  recognized by this unit.
≥Some USB devices cannot be used with this unit.
≥If inserted during playback the USB device may not be recognized by this unit.—
19 7
39 —
— 7
—
USB device cannot be 
operated.
≥Turn the power of this unit off once, and turn it back on. 7
I can’t connect to the 
network.≥Are you subscribed to high speed internet connection? Check that the LAN cable  is properly connected.
≥Have you plugged a telephone cord into the LAN terminal on this unit? Connect  with a straight LAN cable.
≥Confirm the power for the modem or broadband router is turned on.
≥Confirm the network settings. Follow any instructions you may have received from  your ISP (Internet Service Provider) and make changes to the settings.
≥Are the broadband router settings correct? Read the operating instructions for the 
broadband router.
≥Is the broadband router and/or modem connected correctly ? Check the operating  instructions for each device and connect accordingly.
≥Check the “Network” and “BD-Live Internet Access” settings.16
16
—
—
—
—
32, 35
VIERA CAST does not 
operate or connect. ≥Is the network connection correct?
≥Image of the video contents may be disturbed or may not display depending on 
how busy the environment or the connected line is. 16
—
Audio and video 
momentarily pause.≥This occurs between playlist chapters or scenes ([AVCHD]).≥When playing a title recorded on both layers, the unit automatically switches between 
layers and plays the title in the same way as a normal program. However, video and audio 
may momentarily cut out when the unit is switching layers.—
—
Picture-in-picture is not 
played with BD-Video.
≥Confirm whether the disc supports picture-in-picture. —
BD-Live is not played with 
BD-Video. ≥Confirm whether the disc supports BD-Live. 
≥The inserted SD card does not have sufficient available capacity.
≥The SD card is write-protected.
≥Sub contents copied to an SD card are provided by the disc producer as a part of  the BD-Video content. Even if you record images and audio onto an SD card, it 
cannot be played as a BD-Live.22
227
22
Alternative soundtrack and 
subtitles cannot be 
selected. ≥The languages are not recorded on the media.
≥You may not be able to use the on-screen menu to change the soundtrack and 
subtitles on some discs. Use the disc’s menus to make changes. —
19
No subtitles.≥Subtitles are not recorded on the media.
≥Turn the subtitles on. Set “Subtitle” on the on-screen menu to “On”.
≥When progressive output is on, closed captions cannot be displayed.—
30 —
The subtitles overlap closed 
captions recorded on discs. ≥Turn off the subtitles or turn off the closed caption setting on the TV.
30
The resume play function 
does not work.≥Memorized positions are canceled when 
–pressing [ ∫] several times.
–opening the disc tray.
≥The resume play function may not work depending on the media.
≥[BD-V]: On BD-Video discs including BD-J, the resume play function does not work.
—
—
—
RQT9378~Body_mst.fm  44 ページ  ２００８年１２月２５日　木曜日　午後６時１分 
						

							RQT9378
45
Specifications
Signal system: 
NTSC
Operating temperature range: i5 oC to i 35 oC ( i41  oF to  i95  oF)
Operating humidity range: 10 % to 80 % RH (no condensation)
Playable disc: BD-Video
BD-ROM:Version 2
BD-RE: Version 3 (Single Layer, Dual Layer), JPEG*
6
BD-R: Version 2 (Single Layer, Dual Layer)
DVD-RAM:DVD Video Recording format, AVCHD format*8, 
JPEG*4
DVD-R/DVD-R DL: DVD-Video format*1, DVD-Video Recording 
format*1, AVCHD format*1, 8, DivX*7, JPEG*4, 
MP3
DVD-RW:DVD-Video format*
1, DVD-Video Recording 
format*1, AVCHD format*1, 8
+R/+RW/+R DL: Video*1, AVCHD format*1, 8
DVD-VIDEO:DVD-Video format
CD-Audio:CD-DA
CD-R/CD-RW:CD-DA, JPEG*
5, MP3, DivX*7
SD card:
SD Memory Card*2 formatted FAT12, FAT16, FAT32*3:
JPEG*4, AVCHD format*8, MPEG-2
USB device: USB Standard:USB 2.0 High Speed  MP3, JPEG*
4, DivX*7
Format: FAT12, FAT16, FAT32
Video output: Output level: 1.0 Vp-p (75 ≠)
Output connector: Pin jack (1 system)
Component video output:  (1080i/720p/480p/480i)
Y output level: 1.0 Vp-p (75 ≠)
P
B output level: 0.7 Vp-p (75 ≠)
PR output level: 0.7 Vp-p (75 ≠)
Output connector:  Pin jack (Y: green, P
B: blue, PR: red)
(1 system)
Audio output: Output level: 2 Vrms (1 kHz, 0 dB)
Output connector: Pin jack
Number of connectors :
[BD80]: 7.1 channel discrete output:  1 system
(2 channel + 5.1 channel discrete output)
 
[BD60]  [BD601] [BD605]: 2 channel: 1 system
Audio performance: Frequency response:
≥DVD (linear audio): 4 Hz to 22 kHz (48 kHz sampling) 4 Hz to 44 kHz (96 kHz sampling)
≥CD-Audio: 4 Hz to 20 kHz
S/N ratio: 115 dB
Dynamic range: 100 dB
Total harmonic distortion: 0.003 %Digital audio output:
Optical digital output: Optical terminal
Coaxial digital output 
[BD80]: Pin  jack
HDMI AV output  Output format: 480p (525p)/1080i (1125i)/720p (750p)/1080p 
(1125p)
Output Connector: Type A (19 pin)
HDMI
TM (Deep Color, x.v.ColorTM, High Bit rate Audio)
≥This unit supports “HDAVI Control 4” function.
SD card slot:  Connector: 1 system
USB slot: Connector: 1 system
Ethernet:  10BASE-T/100BASE-TX: 1 system
Optical pick-up: System with 2 lenses
Wave length: 790 nm (CDs)/650 nm (DVDs)/405 nm (BDs)
LASER Specification
Class  I LASER Product:
Wave length: 790 nm (CDs)/650 nm (DVDs)/405 nm (BDs)
Laser power: No hazardous radiation is emitted with the safety 
protection
Power supply:  AC 120 V, 60 Hz
Power consumption:
 
[BD80] :
Approx. 23 W
[BD60] [BD601]  [BD605]:Approx. 22 W
Power consumption
 in standby mode:less than 0.5 WPower consumption in quick start standby mode:[BD80]: 6 W[BD60]  [BD601]  [BD605]: 5 W
Dimensions (Wk Dk H)[BD80] : Excluding the projecting parts:
430 mmk242 mm k55 mm
(Approx. 16 15/16 zk9 9/16 zk2 3/16 z)
Including the projecting parts: 430 mmk249 mm k55 mm
(Approx. 16 15/16 zk9 13/16 zk2 3/16 z)
[BD60] [BD601]  [BD605] : Excluding the projecting parts:
430 mmk242 mm k49 mm
(Approx. 16 15/16 zk9 9/16zk 1 15/16z)
Including the projecting parts: 430 mmk249 mm k49 mm
(Approx. 16 15/16 zk9 13/16 zk1 15/16 z)
Mass (Weight): Approx. 2.6 kg (5.7 lbs)
Specifications are subjec t to change without notice. 
*1 Finalizing is necessary.
*2 Includes SDHC card Includes miniSD Cards (need a miniSD Adaptor)
Includes microSD Cards (need a microSD Adaptor)
*3 Does not support long file name.
*4 The total combined maximum number of recognizable picture  contents and folders: 3000 picture contents and 300 folders.
*5 The total combined maximum number of recognizable picture 
contents and folders: 999 picture contents and 99 folders.
*6 The total combined maximum number of recognizable picture 
contents and folders: 9999 picture contents and 300 folders.
*7 [BD80] : The total combined maximum number of recognizable 
picture contents and folders: 200 file contents and 300 folders.
*8 AVCHD format V1.0
≥ Useable capacity will be less. (SD Card)
Reference
DMP-BD80_60_601_605PP-RQT9378_ENG.book  45 ページ  ２００９年２月１９日　木曜日　午後４時４８分 
						

							46
RQT9378
Limited Warranty (Only for U.S.A. and Puerto Rico)
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094
Panasonic Blu-ray Disc Player Limited Warranty
Limited Warranty Coverage (For U.S.A. and Puerto Rico Only)
If your product does not work  properly because of a defect in 
materials or workmanship, P anasonic Consumer Electronics 
Company (referred to as “the warrantor”) will, for the length of the 
period indicated on the chart below, which starts with the date of 
original purchase (“Limited Warranty period”), at its option either (a) 
repair your product with new or refurbished parts, or (b) replace it with 
a new or a refurbished product. The dec ision to repair or replace will 
be made by the warrantor.
During the “Labor” Limited Warranty period there will be no charge for 
labor. During the “Parts” warranty period, there will be no charge for 
parts. You must mail-in your product during the warranty period. If 
non-rechargeable batteries are included, they are not warranted. This 
Limited Warranty only applies to pr oducts purchased and serviced in 
the United States or Puerto Rico.  This Limited Warranty is extended 
only to the original purchaser and  only covers product purchased as 
new. A purchase receipt or other proof of original purchase date is 
required for Limited Warranty service.
Carry-In or Mail-In Service
For Carry-In or Mail-In Service in  the United States and Puerto Rico 
call 1-800-211-PANA (7262) or visit
Panasonic Web Site: http://www.panasonic.com
When shipping the unit carefully pack and send it prepaid, adequately 
insured and preferably in the original carton. Include a letter detailing 
the complaint and provide a day  time phone and/or email address 
where you can be reached.
IF REPAIR IS NEEDED DURING THE LIMITED WARRANTY 
PERIOD THE PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
Limited Warranty Limits And Exclusions
This Limited Warranty ONLY COVERS failures due to defects in 
materials or workmanship, and DOES NOT COVER normal wear and 
tear or cosmetic damage. The Limited Warranty ALSO DOES NOT 
COVER damages which occurred in sh ipment, or failures which are 
caused by products not supplied by the warrantor, or failures which 
result from accidents, misuse, abuse, neglect, mishandling, 
misapplication, alteration, faulty installation, set-up adjustments, 
misadjustment of consumer controls, improper maintenance, power 
line surge, lightning damage, modifica tion, or commercial use (such 
as hotel, office, restaurant, or other business), rental use of the 
product, or service by anyone other t han a Factory Service Center or 
other Authorized Servicer, or damage that is attributable to acts of 
God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED 
UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR 
IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL 
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR 
ARISING OUT OF ANY BREACH OF THIS WARRANTY.  (As 
examples, this excludes damages for lost time, cost of having 
someone remove or re-install an installed unit if applicable, travel to 
and from the servicer, loss of or damage to media or images, data or 
other recorded content. The items liste d are not exclusive, but are for 
illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE 
WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE 
PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or 
consequential damages, or limitations on how long an implied Limited 
Warranty lasts, so the exclusions may not apply to you.
This Limited Warranty gives you specific legal rights and you may 
also have other rights which vary from state to state. If a problem with 
this product develops during or after the Limited Warranty period, you 
may contact your dealer or Service Center. If the problem is not 
handled to your satisfaction, then write to the warrantor’s Consumer 
Affairs Department at the addresses listed for the warrantor.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS 
LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.
As of October 2008
Product or Part Name Parts Labor
Blu-ray Disc Player
One (1) Year One (1) Year
Customer Services Directory (United States and Puerto Rico)
Obtain Product Information and Operating Assistance; purchase Parts, Accessories, or obtain Literature by visiting our Web Site  at:http://www.panasonic.com/helpor, contact us via the web at:http://www.panasonic.com/contactinfoYou may also contact us directly at:
1-800-211-PANA (7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.
For hearing or speech impaired TTY users, TTY: 1-877-833-8855
Accessory Purchases (United States and Puerto Rico)
Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at:http://www.pstc.panasonic.comor, send your request by E-mail to:[email protected] may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday – Friday 9 am to 9 pm, EST.)
Panasonic Service and Technology Company
20421 84th Avenue South, Kent, WA 98032
(We Accept Visa, MasterCard, Discover Card, American Express, and Personal Checks)
For hearing or speech impaired TTY users, TTY : 1-866-605-1277
Product Repairs (United States and Puerto Rico)
Centralized Factory Service Center
MAIL TO:
Panasonic Service and Technology Company 410B Airport Road
Elgin, IL 60123-9333
Attention: BD/DVD Repair
Please carefully pack and ship, prepaid and insured, to the Elgin Centralized Factory Service Center. 
DMP-BD80_60PP-RQT9378_ENG.book  46 ページ  ２００８年１２月２２日　月曜日　午後８時２７分 
						

							RQT9378
47
Limited Warranty (Only for CANADA)
Panasonic Canada Inc.
PANASONIC PRODUCT—LIMITED WARRANTY
Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship and agrees to remedy any such defect for a 
period as stated below from the date of original purchase.
Technics Audio Product  One (1) year, parts and labour
Panasonic Portable/Clock Radio (without Tape, CD, MD) One (1) year, parts and labour
Panasonic Audio/SD Audio Product One (1) year, parts and labour
Panasonic BD/DVD Product  One (1) year, parts and labour
Panasonic Combination DVD Player/VCR One (1) year, parts and labour
Panasonic Combination DVD Recorder/VCR One (1) year, parts and labour
Accessories including rechargeable batteries  Ninety (90) days
LIMITATIONS AND EXCLUSIONS
This warranty does not apply to products purchased outside Canada or to any product which has been  improperly installed, subjected to usage for 
which the product was not designed, misused  or abused, damaged during shipping, or which has been altered or repaired in any way that affects 
the reliability or detracts from the performance, nor does it co ver any product which is used commercially. Dry cell batteries are also excluded from 
coverage under this warranty.
This warranty is extended to the original end  user purchaser only. A purchase receipt or other proof of date of original purchase is required before 
warranty service is performed.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES.
In certain instances, some jurisdictions do not allow the excl usion or limitation of incidental or consequential damages, or th e exclusion of implied 
warranties, so the above limitations  and exclusions may not be applicable. 
WARRANTY SERVICE
FOR PRODUCT OPERATION ASSISTANCE,  please contact:
Our Customer Care Centre: Telephone #:  (905) 624-5505 1-800 #:  1-800-561-5505
Fax #:  (905) 238-2360
Email link: “Customer support” on www.panasonic.ca
FOR PRODUCT REPAIRS, please locate your nearest Authoriz ed Servicentre at www.panasonic.ca :
Link : “Servicentres
TM locator” under “Customer support”
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and preferably in the original carton.  Include details of the defect claimed,  and proof of date of original purchase.
Reference
DMP-BD80_60PP-RQT9378_ENG.book  47 ページ  ２００８年１２月２２日　月曜日　午後８時２７分 
						

							RQT9378
48
Product Service
1. Damage requiring service—The unit should be serviced by 
qualified service personnel if:
(a) The AC power supply cord or AC adaptor has been damaged; 
or
(b )Objects or liquids have gotten into the unit; or
(c) The unit has been exposed to rain; or
(d) The unit does not operate normally or exhibits a marked 
change in performance; or
(e) The unit has been dropped or the cabinet damaged.
2. Servicing —Do not attempt to service the unit beyond that 
described in these operating instructions. Refer all other 
servicing to authoriz ed servicing personnel.
3. Replacement parts —When parts need replacing ensure the 
servicer uses parts specified by  the manufacturer or parts that 
have the same characteristics as the original parts. Unauthorized 
substitutes may result in fire, electric shock, or other hazards.
4. Safety check —After repairs or service, ask the servicer to 
perform safety checks to confirm  that the unit is in proper working 
condition.
Product information
For product information or assistance with product operation:
In the U.S.A. and Puerto Rico, refer to “Customer Services Directory 
(United States and Puerto Rico)” on page 46.
In Canada, contact the Panasonic Canada Inc. Customer Care 
Centre at 1-800-561-5505, or visit the website (www.panasonic.ca), 
or an authorized Servicentre closest to you.
User memo: The model number and serial num
ber of this product can be 
found on either the back or the bottom of the unit.
Please note them in the space provided below and keep for
future reference.
MODEL NUMBER     
SERIAL NUMBER     
DATE OF PURCHASE     
DEALER NAME    
DEALER ADDRESS    
TELEPHONE NUMBER   
Licenses
Java and all Java-based trademarks and logos are trademarks or 
registered trademarks of Sun Microsystems, Inc. in the United 
States and other countries.
Manufactured under license from Dolby Laboratories. Dolby and 
the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent #’s: 5,451,942; 
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 
7,392,195; 7,272,567; 7,333,929; 7,212,872 & other U.S. and 
worldwide patents issued & pending.
DTS is a registered trademark and the DTS logos, Symbol, 
DTS-HD and DTS-HD Master Audio | Essential are trademarks of 
DTS, Inc.
© 1996-2008 DTS, Inc. All Rights Reserved.
This product incorporates copyright protection technology that is 
protected by U.S. patents and other intellectual property rights. 
Use of this copyright protection te chnology must be authorized by 
Macrovision, and is intended for home and other limited viewing 
uses only unless otherwise authori zed by Macrovision. Reverse 
engineering or disassembly is prohibited.
HDMI, the HDMI logo and High-Definition Multimedia Interface are 
trademarks or registered trademarks of HDMI Licensing LLC.
This product is licensed under the  AVC patent portfolio license and 
VC-1 patent portfolio license for the personal and non-commercial 
use of a consumer to (i) encode video in compliance with the AVC 
Standard and VC-1 Standard (“AVC/VC-1 Video”) and/or (ii) 
decode AVC/VC-1 Video that was encoded by a consumer 
engaged in a personal and non-commercial activity and/or was 
obtained from a video provider licensed to provide AVC/VC-1 
Video. No license is granted or shall be implied for any other use. 
Additional information may be obtained from MPEG LA, LLC. See 
http://www.mpegla.com
.
HDAVI Control™ is a trademark of Panasonic Corporation.
“x.v.Color
TM” is a trademark.
VIERA Link
TM is a trademark of Panasonic Corporation.
VIERA CAST
TM is a trademark of Panasonic Corporation.
EZ Sync™ is a trademark of Panasonic Corporation.
“AVCHD” and the “AVCHD” logo are trademarks of Panasonic 
Corporation and Sony Corporation.
SDHC Logo is a trademark.
Portions of this product are prot ected under copyright law and are 
provided under license by ARIS/SOLANA/4C.
Plays DivX
® video
DivX® is a registered trademark of DivX, 
Inc., and is used under license.
“Blu-ray Disc” is trademark.
“BD-LIVE” logo is trademark of Blu-ray Disc Association.
“BONUSVIEW” is trademark of Blu-ray Disc Association.
YouTube and Picasa are trademarks of Google,Inc.
DMP-BD80_60_601_605PP-RQT9378_ENG.book  48 ページ  ２００９年２月１９日　木曜日　午後４時４８分 
						

							RQT9378
49
Referencia rápida en español (Spanish Quick Reference)
Conexiones básicas
A Conexión a un televisor compatible con 
HDMIB Conexión a un televisor con un cable para 
audio/vídeo
Parte posterior de la unidad
≥ Esta conexión no permite la salida de vídeo de alta definición. 
Utilice la conexión  A o  C  para obtener vídeo de alta definición.
C Conexión a un televisor compatible con HDMI y a un amplificador/receptor compatible con HDMI
Conecte el cable de alimentación de CA por último
Ahorro de energía
Esta unidad consume una pequeña cantidad de energía aunque esté 
ajustada en el modo de espera (Accionamiento rápido : Desactivado, 
aprox. 0.5 W). Para ahorrar energía cuando no vaya a utilizar la 
unidad durante mucho tiempo, desenchúfela de la toma de corriente.
Reproducción básica
PreparaciónEncienda el televisor y seleccione la entrada de vídeo adecuada en el televisor.
1 Pulse [ Í BD POWER] para encender la unidad.Después de conectar su nuevo reprodutor y pulsar el botón de 
encendido, aparecerá la pantalla  de la configuración básica.
2Pulse [ 
						

							RQT9378
50
Glossary
AVCHD
AVCHD is a new format (standard) for high definition video cameras 
that can be used to record and play high-resolution HD images. 
BD-J
Some BD-Video discs contain Java applications, and these 
applications are called BD-J. You can enjoy various interactive 
features in addition to playing normal video.
BD-Live
This is a BD-Video (BD-ROM Profile 2) that supports the new 
functions such as Internet connection, etc. in addition to the 
BONUSVIEW function.
Bitstream
This is the digital form of multi-channel audio data (e.g., 5.1 channel) 
before it is decoded into its various channels.
BONUSVIEW (Final Standard Profile)
This is a BD-Video (BD-ROM Profile 1 version 1.1) that supports the 
new functions such as Picture-in-picture, Secondary Audio, etc.
Deep Color
Deep Color is a name for device that can reproduce greater color 
gradation (4096 steps) when connected to a TV that supports the 
Deep Color with HDMI cable. You can enjoy exceptionally rich, 
natural-looking colors, with smooth, detailed gradation and minimal 
color banding. [A lower color gradation (256 steps), without Deep 
Color, will be reproduced if connected  to a TV which does not support 
Deep Color. The unit will automatically set appropriate output to suit 
the connected TV.]
DivX  [BD80]
DivX is a popular media technology created by DivX, Inc. DivX media 
files contain highly compressed video with high visual quality that 
maintains a relatively small file size.
DNS Server
A server which acts like a telephone directory and translates Internet 
domain names into IP addresses.
Dolby Digital
This is a method of coding digital signals developed by Dolby 
Laboratories. Apart from stereo (2-channel) audio, these signals can 
also be multi-channel audio.
Dolby Digital Plus
Multi-channel audio and higher audio quality is made possible using 
Dolby Digital Plus. BD-Video supports up to 7.1 channel output.
Dolby TrueHD
Dolby TrueHD is a very high quality audio format that reproduces the 
studio master audio. BD-Video supports up to 7.1 channel output.
Down-mixing
This is the process of remi xing the multi-channel audio found on 
some discs into fewer channels.
DTS (Digital Theater Systems)
This surround system is used in m any movie theaters. There is good 
separation between the channels, so realistic sound effects are 
possible.
DTS-HD
DTS-HD is a high-quality, sophisticated audio format used in movie 
theaters. Previous DTS Digital Surround-compatible equipment can 
play DTS-HD as DTS Digital Surround audio. BD-Video supports up 
to 7.1 channel output.
DTS-HD High Resolution Audio
This is a signal format achieved  by improving the previous DTS, 
DTS-ES and DTS96/24 formats. It is compatible with sampling 
frequency 96 kHz/48 kHz. BD-Video supports up to 7.1 channel 
output.
DTS-HD Master Audio
This is a lossless audio format and compatible with 96 kHz/7.1ch or 
less. In addition, faithful reproduction of the master audio is enabled 
using lossless audio encoding technology. BD-Video supports up to 
7.1 channel output. Dynamic range
Dynamic range is the difference between the lowest level of sound 
that can be heard above the noise of the equipment and the highest 
level of sound before distortion occurs.
Dynamic range compression means reducing the gap between the 
loudest and softest sounds. This 
means you can listen at low 
volumes but still hear dialog clearly.
Film and video
DVD-Video are recorded using either  film or video. This unit can 
determine which type has been used, then uses the most suitable 
method of progressive output.
Film: Recorded at 24 frames per second. (Recorded at 30  frames per second as well).  Generally appropriate for 
motion picture films.
Video: Recorded at 30 frames/60 fields per second. Generally  appropriate for TV drama programs or animation.
Frames and fields
Frames refer to the single images that constitute the video you see 
on your television. Each frame consists of two fields.
≥ A frame still shows two fields, so there may be some blurring, but 
picture quality is generally better.
≥ A field still shows less picture information so it may be rougher, but 
there is no blurring.
Gateway
IP address of the electronic device providing Internet access.
Usually called a router IP address. (e.g., 192.168.0.1)
HDMI (High-Definition Multimedia Interface)
HDMI is a digital interface for cons umer electronic products. Unlike 
conventional connections, it transmits uncompressed digital video 
and audio signals on a single cable.
Hub
Used for connecting more than one device to the network.
IP address
A set of numbers which distinguish each device on the network when, 
for example, connected to the Internet. When using a PC in a LAN to 
access a PC or device that is not included in the LAN, the IP address 
is called  t

he local IP address. (e.g., 192.168.0.10)
JPEG (Joint Photographic Experts Group)
This is a system used for compressing/decoding color still pictures. If 
you select JPEG as the storage system on digital cameras, etc., the 
data will be compressed to 1/10–1/100 of its original size. The benefit 
of JPEG is less deterioration in picture quality considering the degree 
of compression.
LAN (Local Area Network)
A group of linked devices in a company, school or home.
Indicates the boundaries of a particular network.
Local storage
This storage area is used as a destination for sub contents for playing 
BD-Live on BD-Video.
LPCM (Linear PCM)
These are a kind of PCM format.
These are uncompressed digital sig nals, similar to those found on 
CDs.
MPEG2 (Moving Picture Experts Group)
A standard for efficiently compressing and expanding color video.
MPEG2 is a compression standard used for DVD and satellite based 
digital broadcasting.
MP3 (MPEG Audio Layer 3)
An audio compression method that compresses audio to 
approximately one tenth of its size without any significant loss of 
audio quality. Frame
Field Field
u
r
RQT9378~Body_mst.fm  50 ページ  ２００８年１２月２５日　木曜日　午後３時２９分