Panasonic Dmp Bbt01 Owners Manual

							Connections & Settings
11VQT3W08
1Remove the screw at the bottom of the supplied pedestal using a screwdriver (+), and separate the 
top section and the bottom section of the pedestal. Top section of the pedestal is not used.
2 Align the rear end of the main unit against the rear end of the pedestal, and lower the main unit. 　
Press and secure the main unit into the pedestal.
To reattach the pedestal
Fit the projecting part ( A) into the groove ( B). Secure the two sections with the screw.
	≥ Do not install in a way other than described above. Also, do not move the unit during playback. It may cause 
malfunction of the unit or damage the disc.
≥ Do not hold the pedestal to lift up or carry the unit.
STEP 2 : Connecting to a TV
≥Before making any connections, we recommend that y ou temporarily disconnect all the units from AC 
power.
≥ Use the High Speed HDMI cables. Non-HDM I-compliant cables cannot be utilized.
The HDMI-compliant cable is supplied with this unit.
It is recommended that you use Panasonic’s HDMI cable. When outputting 1080p signal, please use 
HDMI cables 5.0 meters (16.4 ft.) or less.
Recommended part number (High Speed HDMI Cable):
RP-CDHS15 (1.5 m/4.9 ft.), RP-CDHS30 (3.0 m/ 9.8 ft.), RP-CDHS50 (5.0 m/16.4 ft.), etc.
Vertical installation with pedestal




Remote control 
signal sensorTo reattach (
>below)
HDMI IN
HDMI cable (supplied)
Connections & Settings
DMP-BBT01_VQT3W08 _eng.book  11 ページ  ２０１２年４月６日　金曜日　午後３時０分 
						

							12VQT3W08
STEP 3 : Connecting to an amplifier/receiver
Perform either one of the following connections in accordance with your amplifier/receiver input 
terminal.
≥Set “Digital Audio Output” ( >29).
≥ When connecting to a non-3D compatible amplifier/receiver, connect this unit to a TV via HDMI AV 
OUT, then connect the TV and the amplifier/receiver. Please note, however, that the audio can only 
be up to 5.1ch.
≥ When using the TV or amplifier/receiver that does not have the indication of “(ARC)” 
(non-ARC-compatible) on the HDMI terminal, in order to  enjoy TV’s sound by amplifier/receiver it is 
also required to connect the amplifier/receiver and TV using an optical digital cable.
≥ Set “HDMI Audio Output” to “Off” ( >29).
≥ Set “Digital Audio Output” ( >29).
HDMI AV OUT
DIGITAL AUDIO OUT (OPTICAL)
HDMI IN
(ARC)HDMI OUT (ARC)HDMI IN
Amplifier/receiver
HDMI cable (supplied)
HDMI cable
OPTICAL IN
Amplifier/receiver
Optical digital cable
DMP-BBT01_VQT3W08 _eng.book  12 ページ  ２０１２年４月６日　金曜日　午後３時０分 
						

							Connections & Settings
13VQT3W08
STEP 4 : Connecting to the network
The following services can be used when this unit is connected to broadband.
≥ Firmware can be updated  (> 16)
≥ You can enjoy BD-Live ( >21)
≥ You can enjoy VIERA Connect ( >22)
≥ You can access other devices (Home Network) ( >23)
≥ This unit supports Wi-Fi Direct
TM and can make a wireless connection to wireless devices without 
router. You can use this function when enjoying Home  Network feature, etc. Internet access is not 
available while connected via Wi-Fi Direct
TM. ( > 23, 31)
For details about connection method, refer to the instructions supplied with the connected equipment.
This unit can be connected to  a wireless router wirelessly.
≥ For up-to-date compatibility information on your wireless router, refer to
http://panasonic.jp/support/global/cs/
(This site is in English only.)
For additional information about this unit refer to 
http://www.panasonic.com/consumer/support (For U.S.A.)
≥ The unit is not compatible with public wireless LAN se rvices provided in airports, stations, cafes, etc.
≥ See page 39 for the precautions for wireless LAN connection.
≥ Use category 5 or above straight LAN cables  (STP) when connecting to peripheral devices.
≥ Inserting any cable other than a LAN cable in the LAN terminal can damage the unit.
STEP 5 : Connecting to an AC power source
≥This unit consumes a small amount of AC power ( >40) even when turned off. In the interest of 
power conservation, if you are not planning to us e the unit for an extended period of time, please 
disconnect the AC power supply cord from the household AC outlet.
≥ Do not use any other AC adaptors except the supplied one.
Wireless LAN connection
LAN cable connection
Wireless router, etc.
Internet
LAN Cable
Internet
Broadband router, etc.
AC power supply cord (supplied)
To a household AC outlet
AC adaptor (supplied)
Connections & Settings
DMP-BBT01_VQT3W08 _eng.book  13 ページ  ２０１２年４月６日　金曜日　午後３時０分 
						

							14VQT3W08
STEP 6 : Settings
After connecting your new player for the first time 
and pressing [Í], a screen for the basic settings 
will appear.
Preparation
Turn on the television and select the 
appropriate video input on the television.
1Press [ Í].
Please wait until the Status LED lights blue.
Setup screen appears.
2Follow the on-screen instructions and 
apply the settings.
	≥ You can perform this setup anytime by selecting “Easy 
Setting” in the Setup menu. ( >32)
≥ If this unit is connected to a Panasonic TV (VIERA) 
supporting HDAVI Control 2 or later via an HDMI cable, 
then setting information on the TV such as “On-screen 
Language” is acquired by this unit.
After completing “Easy Setting”, you can perform 
“Easy Network Setting”.
Select “Wired”.
Follow the on-screen instructions to apply your 
connection settings.
Preparation
≥Obtain your network name ( >15, SSID).
≥ If your wireless connection is encrypted, 
please be sure that you know your 
encryption key (password).
1Select “Wireless”.
2Select “Search for wireless network” or 
“WPS (PUSH button method)” , then 
follow the on-screen instructions and 
apply the settings.
∫ “WPS (PUSH button method)”
If you are using a wireless router that supports 
WPS (Wi-Fi Protected SetupTM), you can easily 
perform the settings.
Easy Setting
Easy Network Setting
Wired connection
Wireless connection
RETURN
Easy Network Setting
Wired
Wireless
Select a connection mode. 
 Current setting  :  Wired
 
OK
Wireless Settings
Select a connection method.
Please refer to the operating instructions of your wireless 
access point about connection methods.
Search for wireless network
WPS (PUSH button method)
DMP-BBT01_VQT3W08 _eng.book  14 ページ  ２０１２年４月６日　金曜日　午後３時０分 
						

							Connections & Settings
15VQT3W08
∫“Search for wireless network”
The available wireless networks will be displayed.
1 Select your network name.
≥If your network name is not displayed, 
search again by pressing the [R] button on 
the remote control. Stealth SSID will not be 
displayed; in this case, enter manually.
When your wireless network is encrypted
2 Tap to select “Encryption Key”.
3 Enter your encryption key (password). To enter your network name (SSID) manually
If your network name (SSID) is not displayed in 
step 
1, follow these steps.
1 To display the network name (SSID) input 
screen :
Press [HOME]  > select “Setup”  > select 
“Player Settings”  > select “Network” >  select 
“Network Settings”  > select “Wireless 
Settings”  > select “Connection Setting”  > 
select “Manual setting” 
2 Tap to select “SSID” and enter your SSID.
≥If your wireless network is encrypted, go to step 2.
	≥ Refer to the operating instructions of the hub or router.
≥ WPS (Wi-Fi Protected Setup) is a standard that facilitates 
settings relating to the connection and security of wireless 
LAN devices. To see whether your wireless router supports 
WPS, check the wireless router operating instructions.
≥ You can perform this setup anytime by selecting “Easy 
Network Setting” in the Setup menu. ( >31)
≥ You can redo these settings individually using “Network 
Settings”. ( >31)
≥ Do not use this unit to connect to any wireless network for 
which you do not have usage rights.
During automatic searches in a wireless network 
environment, wireless networks (SSID*) for which you 
do not have usage rights may be displayed; however, 
using these networks may be regarded as illegal access.
≥ After performing network settings on this unit, the settings 
(encryption level, etc.) of the wireless router might change. 
When you have trouble getting online on your PC, perform 
the network settings on your PC in accordance with the 
settings of the wireless router.
≥ Please be aware that connecting to a network without 
encryption may result in the content of the communication 
being illegitimately viewed by a third party, or the leaking of 
data such as personal or secret information.
* SSID:
An SSID (Service Set IDentification) is a name used by 
wireless LAN to identify a particular network. 
Transmission is possible if the SSID matches for both 
devices.
OKRETURNSearch againOPTION
Wireless Settings
Reception
Select a wireless network for connection.
Network name (SSID)XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
RG BY
Wireless SettingsEnter the encryption key (password) of the wireless network.
Encryption Key
Set
M
369#“
2580‘
147*;
gnu@,
fmt.-
elsz_
dkry~
cjqx:
bipw/
ahovSpaceSymbols
Encryption Key (Password) 
Shift Delete
Finish
Alphanumeric Other Characters
RETURNOK
aInput Mode
Wireless SettingsEnter your network name (SSID) to connect.
SSID
Set
DMP-BBT01_VQT3W08 _eng.book  15 ページ  ２０１２年４月６日　金曜日　午後３時０分 
						

							16VQT3W08
If you have more than one Panasonic player/
recorder and the remote control operates both 
products at once, you will need to change the 
remote control code to prevent this occurrence. 
(>33, “Remote Control Code”) Occasionally, Panasonic may release updated 
firmware for this unit that may add or improve the 
way a feature operates. These updates are 
available free of charge.
This unit is capable of checking the firmware 
automatically when connected to the Internet via 
a broadband connection.
When a new firmware version is available, the 
following message is displayed.
To update the firmware
Press [HOME] 
> select “Setup” >  select 
“Player Settings” >  select “System” > select 
“Firmware Update”  > select “Update Now”
ACCESS LED will light up while downloading the 
firmware. The unit cannot be operated until the 
ACCESS LED is turned off.
DO NOT DISCONNECT the unit from the AC 
power or perform any operation while the update 
takes place.
After the firmware is installed, the unit will restart 
and the following screen will be displayed.
	≥ If downloading on this unit fails or this unit is not 
connected to the Internet, then you can download the 
latest firmware from the following website and burn it 
to a CD-R to update the firmware.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
To show the firmware version on this unit. 
(> 33, “Firmware Version Information”)
≥ Downloading will require several minutes. It may take 
longer or may not work properly depending on the 
connection environment.
≥ If you do not want to check for the latest firmware version, 
set “Automatic Update Check” to “Off”. ( >33)
Reprogramming the 
remote controlFirmware updates
New firmware is available.
Please update firmware in Setup.
The firmware was updated.Current Version: x.xx
RETURNOK
DMP-BBT01_VQT3W08 _eng.book  16 ページ  ２０１２年４月６日　金曜日　午後３時０分 
						

							Connections & Settings
Playback
17VQT3W08
PlaybackInserting or removing 
media
Inserting disc in the disc slot
≥The disc will be pulled in when inserted partially.
≥ The power will be turned on automatically when 
the disc is inserted while in the standby mode.
To eject the disc
Touch 
[19)
≥ When multiple contents are 
recorded, select the types of 
contents or the title.
SD Card
USB
Network 
Service
Displays the Home screen of 
VIERA Connect. (>
22)
Home 
Network
DLNA Client  (>23)
Media Renderer ( >23)
Player 
Settings
(> 28)
SD Card 
Management
(> 21)
Wallpaper
Changes the background of 
HOME menu.
Videos Music
Photos Setup
Network
HOMEBlu-ray Disc Player
Personalize 
1st user
DMP-BBT01_VQT3W08 _eng.book  17 ページ  ２０１２年４月６日　金曜日　午後３時０分 
						

							18VQT3W08
Multi User Mode
Multi User Mode is a function that enables 
switching of multiple settings easily.
Up to 4 people can use the unit with their own 
settings.
The following settings can be personalized.
≥The user icon
≥ The wallpaper of Home menu
≥ The audio and picture settings ( >25, 28)
A The user name and icon currently selected
B Personalize a new user and switch the 
users with colored buttons.
1Press [HOME].
2Press a colored button that indicates new 
user personalization.
3Select an item and change the settings 
according to the indications.
The following items can be set.
4Select “Confirm”.
To change the personalized user information
Select “Edit User Information” from Setup menu. 
(> 33)
There are three ways to switch the user as follows.
∫ Using colored buttons
Press the colored buttons in the Home menu to 
switch to the user corresponding to the button.
∫Using facial recognition
(Only when connected to Communication 
Camera  >22)
This is a function for fun using the Communication 
camera and enables user switching by facial 
recognition. Perform “Create from Photos” ( >left) 
to personalize your facial photo before using this 
function.
1Press [OPTION] in the Home menu and 
select “Facial Recognition”.
2Turn the face to Communication Camera.
The camera captures your face and determines 
the closest face from the personalized user 
photos, and then displays the results.
≥ Accuracy of the recognition may be 
reduced depending on the captured image.
3Follow the indications on the screen.
≥To redo the facial recognition, press 
[RETURN]. 
∫ Using registered smartphones
When the unit is turned on using the 
registered smartphone, the user who 
registered the smartphone will automatically 
be selected.
≥
Perform the “Remote Device Settings”. (>31)
	≥To use smartphones as a remote control, installation of 
dedicated software is required. For more details, refer to 
the following website.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
Personalizing a new user
Input 
Nickname Personalize a user name.
Select IconPersonalize a user icon. 
Select from Illustrations
The image can be selected from 
prepared illustrations.
Create from Photos
If the Communication camera is 
connected, you can shoot and 
personalize your photo.
≥
You can also select a photo in 
recording media as an icon. 
(> 25, “Icon Personalization”)
Select 
Wallpaper Personalize a background of the 
Home menu.
≥
Other than prepared wallpapers, 
you can also select a photo in 
recording media as a wallpaper. 
(> 25, “Wallpaper”)
Videos Music
Photos Setup
Network
HOMEBlu-ray Disc Player
USER1Personalize 
2nd user
USER1A
B
Personalize 
Smartphone
Smartphone used as a remote 
control can be registered with 
respect to each user.
≥
Multiple users cannot be 
registered for one smartphone.
Switching the user
DMP-BBT01_VQT3W08 _eng.book  18 ページ  ２０１２年４月６日　金曜日　午後３時０分 
						

							Playback
19VQT3W08
Playback
1Insert the media.
Playback starts depending on the media.
2Select the item to play.
Repeat this procedure if necessary.
	≥DISCS CONTINUE TO ROTATE WHILE MENUS ARE 
DISPLAYED. Select [ ∫] from the KEYS screen when you 
have finished playback to protect the unit’s motor, your 
television screen and so on.
≥ DivX 
[For_Canada] and MKV: Successive play is not 
possible.
≥ It is not possible to play back AVCHD and MPEG2 videos 
which have been dragged and dropped or copied and 
pasted to the media.
≥ To save on electricity, the power is turned off automatically 
if there is no button operation for about 30 minutes  when 
not playing back (such as when paused, displaying the 
menu, displaying still pictures, etc.). (Compatible with 
ENERGY STAR)
1Repeatedly press [KEYS] to display the 
playback control screen.
2Select a key.
See page 9 for the KEYS screen operation.
Following functions may not work depending on 
the media and contents. The stopped position is memorized.
Resume play function
Select [
1] (PLAY) to restart from this position.
≥ The position is cleared if the disc is ejected or 
you select [ ∫] several times to display the 
Home menu.
≥ On BD-Video discs including BD-J, the 
resume play function does not work.
Select [ ;] again or [ 1] (PLAY) to restart play.
Frame-by-frame
1 While paused, repeatedly press [KEYS] to 
display the cursor key screen.
2 Select [ 2] or [ 1].
≥ Select [ 1] (PLAY) to revert to normal playback 
speed.
≥ BD-Video and AVCHD: [ 1] only.
Search
While playing, select [ 6] or [5 ].
≥Music and MP3: The speed is fixed to a single step.
Slow-motion
While paused, select [ 6] or [5 ].
≥ BD-Video and AVCHD: [ 5] only.
The speed increases up to 5 steps.
≥ Select [ 1] (PLAY) to revert to normal playback 
speed.
Skip to the title, chapter or track.
It will play back after skipping backward 
approximately 10 seconds every time the key is 
selected.
You can change the audio channel number or 
soundtrack language, etc.
Operations during playback
Stop
Pause
 
Search/
Slow-motion
 Skip
Skip backward 
10 seconds
Changing audio
DMP-BBT01_VQT3W08 _eng.book  19 ページ  ２０１２年４月６日　金曜日　午後３時０分 
						

							20VQT3W08
Basic operation can be performed by swiping the 
edge of the touchpad with your finger, such as the 
following.
≥Perform the operation when the KEYS screen is 
not displayed.
1Repeatedly press [KEYS] to display the 
cursor key input screen.
2Select a key.
See page 9 for the KEYS screen operation.
The following functions may not work depending 
on the media and contents.
Select the item.
The status messages give you information about 
what is currently being played. Each time you 
select [STATUS], the display information may 
change or will disappear from the screen.
≥ Depending on media and contents, the display 
may change or may not appear.
e.g., BD-Video
A T: Title, C: Chapter, PL: Playlist
B Elapsed time in the title
C Current position
D To t a l  t i m e
e.g., JPEG
Quick playback control 
Stop
Play
Pause
Frame-by-frame
(during pause)
Forward: Swipe your 
finger from left to right.
Backward: Swipe your 
finger from right to left.
Search forward
Search backward
Skip forward
Skip backward
or
Displaying menus and 
playback infor mation
 
Show top menu/
pop-up menu
Show the status 
messages
PlayBD-VideoT1     C1     0:05.140:20.52
A
CD
B
                                    
Date           11/12/2007 
Size            500 x 375
Manufacturer
Equipment 1 / 26
DMP-BBT01_VQT3W08 _eng.book  20 ページ  ２０１２年４月６日　金曜日　午後３時０分