Panasonic Dmp B15 Operating Instructions

							Getting started
RQT9334
(E NG)
11
Preparing the Power 
Supply
The unit is in the standby condition (the [Í] indicator lights) 
when the AC power supply cord is connected. The primary 
circuit is always “live” as long as the AC adaptor is connected 
to an electrical outlet.
≥When connecting the AC adaptor, use the unit after setting it 
vertically. Placing the unit with the stand closed 
(e.g.:D10, 3 in “Installation of the unit”) may cause damage 
to or malfunction with the AC adaptor.
To conserve power
This unit consumes 0.5 W (Approximately 5 W when Quick 
Start is set to “On”) of power even when turned off. When the 
unit is not going to be used for a long time, disconnect the AC 
power supply cord from the household AC outlet.
This unit can be used in places without an AC outlet, such as 
outdoors, by attaching the included battery pack.
≥The battery is not charged at the time of purchase. Charge 
before initial use.
≥The battery is designed only for use with this unit. It cannot be 
used with other equipment.
∫Attaching the battery pack
Turn the unit off before attaching or detaching the battery pack.
≥Attach the battery after closing with the LCD screen facing 
inwards and the stand open.
∫Detaching the battery pack
When not using for long periods of time
≥Detach the battery pack (Dabove). 
(Even when the unit is turned off, there is a small amount of 
voltage running through the unit, and this may result in a 
malfunction.)
≥Recharge the battery for re-use.
∫Recharging the battery pack
Attach the battery pack and connect the AC 
adaptor (>left).
≥The [CHARGE] indicator lights while charging the battery, and 
the [CHARGE] indicator turns off when battery charging is 
finished.
∫Approximate recharging and play times (Hours)
*1 When the unit is off [at 20oC (68oF)]
*2 At room temperature using headphones [at 20
oC (68oF)]
≥
The times indicated on the above may differ depending on use.≥To change the LCD brightness (>13, “Adjusting the pictures 
on the LCD screen”).
∫Checking the remaining battery charge
When the unit is on (>12, “Turning on/off the unit”) and 
powered by the battery pack
Press [SUB MENU] to check on the LCD 
(displays for a few seconds).
Using the unit connected to the 
AC adaptor
Using the battery pack
AC adaptor
(included)To a household 
AC outlet AC power supply cord
(included) 1
23
RELEASE
DETACH ATTACH
RELEASE
DETACH ATTACH
Bottom side of this unit
Battery pack
(included)
Clicks into place.
Check to make sure it is securely fastened.2Slide in to the right.1Bring in from the 
left, aligning the 
grooves.
Recharging*1
Play*2
LCD brightness level
j50+5
72.52.252
RELEASE
D E TA C H AT TA C H
Bottom side of this unit
2Slide.
1Press and hold.
[CHARGE] indicator 
(Yellow light)
(screen)
(flashing)
Recharge 
Appears automatically when there is only 
a few minutes of charge remaining.
DMPB15P-RQT9334_eng.book  11 ページ  ２００９年３月２８日　土曜日　午後２時３９分 
						

							RQT9334(ENG )
12
Turning on/off the unit
Press [POWER Í] (approx. 0.5 sec.).
The unit is turned off when [POWER Í] is pressed again.
≥ If the screen is rotated when the unit is turned on, the display 
on the screen will disappear and the unit will be automatically 
turned off. ( >10)
≥ The unit cannot be turned on in situations other than the 
following or when the screen is rotated. ( >10)
≥ When the “Auto Power Off” is set to “On” (initially set to “On”), 
the unit will be turned off automatically after 15 minutes 
(5 minutes when the battery pack is used) when it is in 
stopped status ( >36).
≥ The startup will take time. The operation related to startup of 
the unit after turning on this unit can be quickened by setting 
the initial setup “Quick Start” ( >36) to “On” (initially set to 
“Off”). (The power consumption will increase)
≥ You may hear operational sounds when the unit is turned on, 
but this is due to the initialization of the pickup unit, and it is 
not a malfunction.
After installation of the unit and pressing [POWER Í], a screen 
for the basic settings will appear.
Follow the on-screen instructions and make 
the settings with [ 3,4 ] and [OK].
“On-screen Language” is set. ( >34)
≥You can perform this setup anytime by selecting “Easy 
Setting” in the Setup menu. ( >36)
≥ You can also change this setting individually. ( >34)
The unit is turned off automatically after set time has passed.
Switch by pressing the [OFF TIMER].
It will switch every time it is pressed.
Showing FUNCTIONS 
menu
Some functions of this unit can be operated from the 
FUNCTIONS menu.
1Press [FUNCTIONS].
≥ Functions displayed depend on the media and operating 
conditions.
≥ The FUNCTIONS menu cannot be displayed on the unit 
when selecting “AUX” with [AV SELECT].
When connecting to a TV (VIERA) with an HDMI cable, 
the unit’s FUNCTIONS menu can be displayed on the 
TV screen.
(> 27, “Using the FUNCTIONS menu to operate this 
unit”)
2Press [ 3,4 ] to select the item and press 
[OK].
Easy Setting
Turn the unit off automatically
Off Timer 0
 30
e.g., 30 min.
Off1:00
0:30 2:00 3:00 6:0012:00
≥Playback ( >14, 30)
Show the Home screen of the VIERA CAST when selecting 
“NETWORK” with [AV SELECT].
≥ Top Menu  ( >14)
≥ Menu ( >14, 18, 22)
≥ Viewing Picture ( >18)
≥ Other Functions
j “Playlists”:
You can play playlists created on DVD-VR.
Press [ 3,4,2 ,1] to select the playlist and press [OK].
j “Setup” ( >32)
j “Card Management” ( >17)
≥ Disc ( >14) Switches to the disc drive.
≥ SD card  ( >14) Switches to the SD drive.
≥ Network ( >30) Show the Home screen of the 
VIERA CAST.
≥ AUX ( >25)
OKRETURN
Playback
DISC
Other FunctionsSD card
Network
AUX
Blu-ray Disc Player
e.g.,
RQT9334~Body1_eng.fm  12 ページ  ２００９年３月２８日　土曜日　午後６時３２分 
						

							Getting started
RQT9334
(E NG)
13
Adjusting the pictures on 
the LCD screen
1
Press [LCD].
≥It is also possible to display with the following procedures.
2Select the item with [3,4].
3Change the setting with [3,4,2,1].
≥Underlined items are the factory presets.
∫When selecting other settings than “AUX” with 
[AV SELECT]
Picture:Adjusting image quality
Monitor:Displaying images
∫When selecting “AUX” with [AV SELECT] (>25)
PICTURE:Adjusting image quality
MONITOR:Displaying images
≥If you are not using the LCD on this unit, select “Off (OFF)” to 
conserve power. (The [Í] indicator flashes.)
≥If the settings in “PICTURE” are changed when “AUX” is 
selected, the settings in “Picture” will also change.
The settings will change in the same way even when 
something other than “AUX” is selected.
To exit the screen
Press [LCD] or [RETURN].
To display images when the “Monitor (MONITOR)” is 
set to “Off (OFF)”
Press [LCD] or [SUB MENU]
Loading the disc or SD 
card
1
Open the screen and press [OPEN].
2Set the disc holding the unit with your hand 
and close the lid.
3Close the screen.
≥Some discs may start playing when it is loaded with the unit 
turned on.
≥About discs with a cartridge
jBD-RE with a cartridge: It cannot be used with this unit. (It 
cannot be used even if the disc is taken out from the 
cartridge.)
jDVD-RAM, 8 cm disc: Remove the disc from the cartridge 
and set the disc in the tray
jPlace the disc back into the cartridge for storage to prevent 
dirt and scratches after use.
≥Do not touch the lens as it may 
make it dirty.
1Open the cover at the side of the unit.
2Insert the SD card into the SD card slot.
≥Press on the center of the card until it clicks into place.
3Close the cover.
To remove the card
In step 2 above, press the center of the card until it “clicks”, and 
pull the card out straight. 1Press [SUB MENU].
2Select “Other Functions” with 
						

							RQT9334
(ENG )
14
Playback
Basic play (Playing video 
contents)
Instructions for operations are generally described using the 
remote control in these operating instructions.
PreparationInsert a disc or SD card (>13 ).
Press [AV SELECT] to select “DISC” or “SD”.
Play starts.
≥If play does not start, press [1](PLAY).
≥If a media with data in different file formats is inserted, the file 
selection menu is displayed. Press [3,4] to select the 
desired file format and press [OK].
≥If the menu is displayed, press [3,4,2,1] to select the 
item and press [OK].
≥If the screen prompting you to use the color buttons appears, 
continue to operate with the color buttons on the remote 
control.
≥DISCS CONTINUE TO ROTATE WHILE MENUS ARE 
DISPLAYED. Press [∫] when you finish to preserve the 
unit’s motor.
≥The producers of the disc can control how discs are played. 
So you may not always be able to control play as described in 
these operating instructions. Read the disc’s instructions 
carefully.
≥When playing a set of two or more BD-Video discs, the menu 
screen may continue to display even if the disc has been 
ejected.
≥The start of playback may take time depending on the disc or 
SD card.
≥The sound of rotation may be audible during disc playback, 
but this is not a malfunction.
Press [jVOL] or [iVOL].
≥When using headphones, turn down the volume before 
connection.
[BD-V] [AVCHD] ]DVD-VR] [DVD-V] [DivX]
Press [TOP MENU/DIRECT NAVIGATOR].
≥Total title number may not be displayed properly on +R/+RW.
[BD-V]
The Pop-up menu is a special feature available with some BD-
Video discs. This menu may vary with discs. For the operating 
method, refer to the instructions for the disc.
1Press [POP-UP MENU].
2Press [3,4,2,1] to select the item and press [OK].
≥Pop-up menu also appears by pressing [SUB MENU] and 
selecting “Pop-up Menu”.
≥Press [POP-UP MENU] to exit the screen.[AVCHD] [MPEG2]
It is possible to playback the HD (High Definition) video 
recorded on the Panasonic High definition Video Camera on 
the DVD-RAM/R/RW/R DL/+R/+RW/+R DL or SD card, and SD 
(Standard Definition) Video recorded on the Panasonic SD 
Video Camera on the SD card.
PreparationInsert a disc or SD card (>13).
1Press [AV SELECT] to select “DISC” or 
“SD”.
≥“Video (AVCHD)” or “Video (MPEG-2)” screen is 
displayed.
≥If a media containing data in different file formats is 
inserted, the file selection menu may be displayed.
Press [3,4] to select “Play Video (AVCHD)” or “Play 
Video (MPEG-2)” and press [OK].
2Press [3,4,2,1] to select the title and 
press [OK].
≥Total title number may not be displayed properly on +R/
+RW.
To return to the menu screen
Press [DIRECT NAVIGATOR].
To exit the menu screen
Press [RETURN].
(If the media contains data in different file formats)
1Press [FUNCTIONS].
2Press [3,4] to select “Menu” and press [OK].
3Press [3,4] to select “Play Video (AVCHD)” or “Play Video 
(MPEG-2)” and press [OK].
≥It may pause for a few seconds on the break of images when 
editing such as partial deletion is performed.
≥High definition video (transfer rate of 18
 Mbps or faster) 
cannot be played back correctly if it was recorded on a DVD 
compatible to double speed or slower.
To adjust the volume
To s ho w  m e nu s
To show Pop-up menu
DIRECT NAVIGATOR Title ViewVideoPicture
01
02
03
04
05
06
07
08
09
109/  5
9/  5
9/  5
9/  6
9/  6
9/  6
9/  7
9/  7
9/  7
9/  7Wed
Wed
Wed
Thu
Thu
Thu
Fri
Fri
Fri
FriIN 2
IN 2
VHS
VHS
 
 
 
IN 2
IN 210:00AM
11:30AM
11:59PM
10:00AM
11:30AM
11:59PM
10:00AM
10:30AM
11:30AM
11:59PMRec. Length
No.Date Day
Channel
StartTitle NameDVD-RAM(VR)
RGSUB
MENUPlayPrevious NextRETURNVideoPicturePage  01/02
0:15 (SP)
e.g., DVD-RAM
Playing HD Video or SD Video 
To switch from other menus to AVCHD or 
MPEG2 menu
SD Card
Play Video (AVCHD)
Select an action or press [RETURN].
Play Pictures (JPEG)
Play Video (MPEG-2)
OK
RETURN SUB
MENU
e.g., 
DIRECT NAVIGATORVideo (MPEG-2)Video
001
002
003
004
005
006
007
008
009
0109/  5
9/  5
9/  5
9/  6
9/  6
9/  6
9/  7
9/  7
9/  7
9/  7Wed
Wed
Wed
Thu
Thu
Thu
Fri
Fri
Fri
Fri 
 
  10:00AM
11:30AM
11:59PM
10:00AM
11:30AM
11:59PM
10:00AM
10:30AM
11:30AM
11:59PMRec. Length
No.Date Day
StartTitle NameSD CARD
SUB
MENUPlayPrevious NextRETURNPage  01/02
0:15.47
e.g., 
DMPB15P-RQT9334_eng.book  14 ページ  ２００９年３月２８日　土曜日　午後２時３９分 
						

							Playback
RQT9334
(E NG)
15
]DVD-VR]
PreparationInsert a disc (>13).
1Press [AV SELECT] 
to select “DISC”.
≥“Title View” screen is 
displayed.
2Press [3,4] to 
select the title and 
press [SUB MENU].
3Press [3,4] to select “View Chapters” 
and press [OK].
4Press [2,1] to select the chapter and 
press [OK].
These functions may not work depending on the media.
Stop
The stopped position is memorized.
Resume play function
Press [1] (PLAY) to restart from this position.
≥The memorized position is cleared in the following instances:
j[∫] is pressed several times.
jThe disc or SD card is removed.
jThe unit is turned off due to such occurrences as power 
outage, the removal of the AC adaptor or waste of the 
battery pack’s remaining power when the unit is turned on.
≥[BD-V]: On BD-Video discs including BD-J (>48), the resume 
play function does not work.
≥[CD] [MP3] [DivX] [MPEG2]: The position is cleared if the unit is 
turned off.
Pause
≥Press [;] again or [1] (PLAY) to restart play. 
Search/Slow-motion
The speed increases up to 5 steps.
≥Press [1] (PLAY) to revert to normal playback speed.
≥For some discs, the speed may not change.
Search
While playing, press [6] or [5].
≥]DVD-VR] [DVD-V]:
Audio is heard during the first level of forward search.
≥[BD-V] [AVCHD] [DivX] [MPEG2]: Audio is not heard during all 
levels of search.
≥[CD] [MP3]: The speed is fixed to a single step.
Slow-motion
While paused, press [6] or [5].
≥[BD-V] [AVCHD]: Forward direction [5] only.
≥]DVD-VR]: If continued for approx. 5 minutes, slow-motion play 
pauses automatically.
Skip
Skip to the title, chapter or track you want to play.
≥Each press increases the number of skips.
≥[DivX]: Backward direction [:] only.
Chapter playback
DIRECT NAVIGATOR Title ViewVideoPicture
01
02
03
04
05
06
07
08
09
109/  5
9/  5
9/  5
9/  6
9/  6
9/  6
9/  7
9/  7
9/  7
9/  7Wed
Wed
Wed
Thu
Thu
Thu
Fri
Fri
Fri
FriIN 2
IN 2
VHS
VHS
 
 
 
IN 2
IN 210:00AM
11:30AM
11:59PM
10:00AM
11:30AM
11:59PM
10:00AM
10:30AM
11:30AM
11:59PMRec. Length
No.Date Day
Channel
StartTitle NameDVD-RAM(VR)
RGSUB
MENUPlayPrevious NextRETURNVideoPicturePage  01/02
0:15 (SP)
e.g.,
Properties
View Chapters
To picture
To display the title properties 
(recording date, etc.)
Playing still pictures (>18) To select the chapter
DIRECT NAVIGATORChapter ViewDVD-RAM(VR)Video
Picture
PlayRETURNPage  001/001
002 003
Play01
0:00.20---------
You are now in ‘‘Chapter View.’’
Please select the chapter you
would like to start playback.
Press [RETURN] for ‘‘Title View.’’
001
0:00.00
e.g.,
Other operations during play
DMPB15P-RQT9334_eng.book  15 ページ  ２００９年３月２８日　土曜日　午後２時３９分 
						

							RQT9334
(ENG )
16
Basic play (Playing video contents) 
(continued)
Direct Play
During playback, you can access specific recordings or scenes 
through direct entry of the numbered buttons. 
Play starts from the selected title or chapter.
≥While stopped (the image on the right is 
displayed on the screen), the title is 
designated. While playing, the chapter is 
designated.
Frame-by-frame
While paused, press [2] (2;) or [1] (;1).
Each press shows the next frame.
≥Press and hold to change in forward or backward succession.
≥Press [1] (PLAY) to revert to normal playback speed.
≥[BD-V] [AVCHD] : Forward direction [1] (;1) only.
Screen Aspect
When black bars are shown at the top, bottom, left, and right 
sides of the screen, you can enlarge the image to fill the 
screen.
1Press [SUB MENU].
2Press [3,4] to select “Other Functions” and press [OK].
3Press [3,4] to select “Screen Aspect” and press [OK].
4Press [2,1] to select “Side cut” or “Zoom”.
Normal: Normal output
Side  cut: The black bars on the right and left sides of the 16:9 
image disappear and the image is enlarged. Please 
note that the right and left sides of the image are cut 
off when the black bar is not displayed.
Zoom: The black bars on the top and bottom sides of the 4:3 
image disappear and the image is enlarged. Please 
note that the top and bottom sides of the image are 
cut off when the black bar is not displayed.
≥Please note that the top, bottom and sides of the image will 
be cut off in images with no black bars.
≥
Screen aspect will return to “Normal” in the following instances:
jPlayback of images starts/ends
jThe unit is turned on/off
≥[BD-V] [DVD-V]: “Side cut” does not have any effect.
≥When “TV Aspect” (>34) is set to “4:3 Pan & Scan” or “4:3 
Letterbox”, the “Zoom” effect is disabled. 
Status messages
The status messages give you information about what is 
currently being played. Each time you press [STATUS], the 
information displayed will change.
≥It is also possible to display with the following procedures:
1Press [SUB MENU].
2Select “Status” with [3,4], and select [OK].
Changing audio during play
≥It is also possible to display with the following procedures:
1Press [SUB MENU].
2Select “Other Functions” with [3,4], and select [OK].
3Select “Audio” with [3,4], and select [OK].
[BD-V] [DVD-V] 
You can change the audio channel number each time you 
press [AUDIO] or [3,4]. This allows you to change the 
soundtrack language (>23, Soundtrack), etc.
]DVD-VR] [DivX] [MPEG2]
AudioLR>AudioL>Audio R
^---------------------------------}
You can change soundtracks each time you press [AUDIO] or 
[OK]. [BD-V] [AVCHD]
e.g., 5: [0] B [0] B [5]
15: [0] B [1] B [5][DVD-V]
e.g., 5: [0] B [5]
15: [1] B [5]
PlayBD-Video
 T1     C1     0:05.140:20.52
T:  T i t l e
C: Chapter
PL: PlaylistItems change 
depending on the 
disc played. No display
Current position Type of disc Play status
Elapsed time in the title e.g., [BD-V]
Depending on the kind of disc or the playback status, this 
display may not appear.To t a l  t i m e
Soundtrack 1 ENG Digital  3/2.1ch
English is selected. e.g., [DVD-V]
PlayDVD-RAM(VR)
AudioLR“AudioLR” 
is selectede.g., 
DMPB15P-RQT9334_eng.book  16 ページ  ２００９年３月２８日　土曜日　午後２時３９分 
						

							Playback
RQT9334
(E NG)
17
Enjoying BD-Live or 
BONUSVIEW in BD-Video 
[BD-V]
What is BONUSVIEW?
BONUSVIEW allows you to enjoy functions such as picture-in-
picture or secondary audio etc., with BD-Video supporting BD-
ROM Profile 1 version 1.1/ Final Standard Profile.
What is BD-Live?
In addition to the BONUSVIEW function, BD-Video supporting 
BD-ROM Profile 2 that has a network extension function allows 
you to enjoy more functions such as subtitles, exclusive images 
and online games by connecting this unit to the Internet. In 
order to use the Internet feature, you must have this unit 
connected to a broadband network (>28).
≥These discs may not be on sale in certain regions.
≥The usable functions and the operating method may vary with 
each disc, please refer to the instructions on the disc and/or 
visit their website.
To turn on/off secondary video
Set “Video” in “Secondary Video” to “On” or 
“Off” (>23, Press [DISPLAY] > “Disc” > 
“Signal Type”)
The secondary video is played.
To turn on/off secondary audio
Set “Soundtrack” in “Secondary Video” to 
“On” or “Off” (>23, Press [DISPLAY] > 
“Disc” > “Signal Type”)
The secondary audio is played.
≥During search/slow-motion or frame-by-frame, only the 
primary video is displayed.
≥When “BD-Video Secondary Audio” in “Digital Audio Output” 
is set to “Off”, secondary audio will not be played even if you 
set “Soundtrack” in “Secondary Video” to “On”. Please check 
that “BD-Video Secondary Audio” is set to “On” (>33).
≥The playback method determined by the disc will take priority, 
so it may not play back in the manner specified with this unit.
≥When the secondary video is turned off, the secondary audio 
will not be played.Many BD-Live compatible discs require content to be 
downloaded onto an SD card (>49, Local storage) in 
order to access the available BD-Live features.
≥An SD card with 1 GB or more of free space (SD Speed Class 
Rating 2 or higher) needs to be inserted prior to inserting the 
BD-Live compatible disc.
Some BD-Live content available on the Blu-ray discs may 
require an Internet account to be created in order to access 
the BD-Live content. Follow the screen display or instruction 
manual of the disc for information on acquiring an account.
Preparation≥Connect to the network. (>28)
1Insert an SD card (>13).
≥If the SD card menu screen is displayed, 
press [RETURN] to clear the screen.
2Insert the disc (>13).
3Press [AV SELECT] to select “DISC”.
≥For operation method, refer to the instructions on the disc.
To use the above functions, it is recommended that you format the 
card on this unit. Format the card using the following procedures:
≥If the SD card you use is formatted, all data on the card will be 
erased. It cannot be recovered.
1Insert an SD card (>13).
2Press [AV SELECT] to 
select “SD”.
3Press [FUNCTIONS].
4Press [3,4] to select 
“Other Functions” and 
press [OK].
5Press [3,4] to select 
“Card Management” and press [OK].
6Press [3,4] to select “BD-Video Data Erase” or “Format 
SD Card” and press [OK].
7Press [2,1] to select “Yes” and press [OK].
8Press [2,1] to select “Start” and press [OK].
≥If you experience any problems, first, try formatting the SD 
card in this unit.
≥A message may be displayed when the SD card doesnt have 
enough storage capacity for BD-Live content.
Please make space available on the current SD card, or 
insert another SD card.
≥While using this feature, do not open the cover at the side of 
the unit or touch the SD card.
≥While using this feature, do not remove the SD card. Doing so 
will cause playback to stop. 
≥The unit must be connected to the Internet and set up (>28) 
to use the BD-Live functions. “BD-Live Internet Access” may 
need to be changed for certain discs (>32).
≥When discs supporting BD-Live are played back, the player 
or disc IDs may be sent to the content provider via the 
Internet. You can restrict Internet access (>32).
≥The playback may be paused depending on the 
communication environment. Some functions may be 
disabled to prevent skipping to sections that have not been 
downloaded, etc.
Playing secondary video (picture-
in-picture) and secondary audio
Primary videoSecondary video
Enjoying BD-Live discs with Internet
Formatting SD cards/Deleting data
Card Management  No. of Files    6 
Free space    300 MB 
SD card 
Format this SD Card. OK 
RETURN 
BD-Video Data Erase Format SD Card 
e.g., 
DMPB15P-RQT9334_eng.book  17 ページ  ２００９年３月２８日　土曜日　午後２時３９分 
						

							RQT9334
(ENG )
18
Playing still pictures
[JPEG]
Playback of the BD-RE, DVD-RAM/R/R DL or CD-R/RW with 
still pictures recorded. This unit can also play still pictures 
recorded on the SD card.
(About structure of folders D39, “Structure of folders that can 
be played in this unit”)
PreparationInsert a disc or SD card (>13 ).
1Press [AV SELECT] to select “DISC” or “SD”.
∫BD-RE, DVD-RAM
“Album View” screen is displayed.
≥When the “Title View” screen is displayed, press the [G] 
button to switch to the “Album View” screen.
≥
If the DVD-RAM containing both JPEG and AVCHD format 
is inserted, the file selection menu may be displayed.
∫DVD-R/R DL, CD-R/RW, SD card
≥If the media containing data in different file formats is 
inserted, the file selection menu may be displayed.
Press [3,4] to select “Play Pictures (JPEG)” and press 
[OK].
“Picture View” screen is displayed.
B Go to step 3
2Press [3,4,2,1] to select the album 
and press [OK].
3Press [3,4,2,1] to select the still 
picture and press [OK].
≥Press [2,1] to display the previous or next still picture.
≥Press [:, 9] to show other pages.
≥Playback is not possible for pictures other than JPEGs.
≥Black bars may be displayed on the top, bottom or sides 
depending on the picture aspect ratio.
To return to the previous screen
Press [RETURN].
To exit the screen
Press [DIRECT NAVIGATOR].(If the media contains data in different file formats)
1Press [FUNCTIONS].
2Press [3,4] to select “Menu” and press [OK].
3Press [3,4] to select “Play Pictures (JPEG)” and press 
[OK].
You can display still pictures one by one at a constant interval.
∫BD-RE, DVD-RAM
1While the “Album View” screen is displayed
Press [3,4,2,1] to select the album 
and press [SUB MENU].
≥You can also start slideshow by pressing [1](PLAY) 
after selecting the album.
2Press [3,4] to select “Start Slideshow” 
and press [OK].
∫DVD-R/R DL, CD-R/RW, SD card
1While the “Picture View” screen is displayed
Press [SUB MENU].
2Press [3,4] to select “Start Slideshow” 
and press [OK].
To stop slideshowPress [∫].
In step 2 in Start Slideshow (Dabove)
1Press [3,4] to select “Slideshow 
Settings” and press [OK].
2To change the display interval
Press [3,4] to select “Display Interval” and press [2,1] 
to select the interval (“Long”, “Normal” or “Short”).
≥When a still picture with a large number of pixels is 
played, the display interval may become longer. Even if 
the setting is changed, the display interval may not 
become shorter.
To set display method
Press [3,4] to select “Transition Effect” and press 
[2,1] to select “Fade”, “Motion” and “Random”.
SD Card
Play Video (AVCHD)
Select an action or press [RETURN].
Play Pictures (JPEG)
Play Video (MPEG-2)
OK
RETURN SUB
MENU
e.g., 
Â
3(
 Total 8 106_DVD
 Total 1312/9/2006 
SUB
MENU
DIRECT NAVIGATORAlbum ViewDVD-RAM(VR)VideoPicture
OK Press [OK] to go to Picture View.Previous Next SlideshowRETURNVideoPicturePage  02/02
e.g.,
SUB
MENU
DIRECT NAVIGATORPicture ViewDVD-RAM(VR)
Play
RETURN
2006  9  12
Page  001/001
0001
0005
00090006 0007 0008 0002 0003 0004
VidéoImage
e.g.,
To switch from other menus to JPEG menu
Useful functions during still 
picture play
Start Slideshow
Slideshow settings
“Fade”: Pictures are changed by fading out and 
fading in.
“Motion”: Pictures are changed by fading out and 
fading in, while they are enlarged, reduced, 
or moved up or down.
“Random”: In addition to the “Motion”, pictures are 
changed by various methods.
DMPB15P-RQT9334_eng.book  18 ページ  ２００９年３月２８日　土曜日　午後２時３９分 
						

							Playback
RQT9334
(E NG)
19
To repeat slideshow
Press [3,4] to select “Repeat Play” and press [2,1] to 
select “On” or “Off”.
To listen to a Background Music (SD card only)
The music CD can be played back as Background Music 
during the slideshow.
Press [3,4] to select “Soundtrack” and press [2,1] to 
select “On” or “Off”.
≥You cannot search or skip the music.
≥When the slideshow stops, the playback of the music 
also stops.
3Press [3,4,2,1] to select “Set” and 
press [OK].
1While playing (except for slideshow)
Press [SUB MENU].
2Press [3,4] to select “Rotate Right” or 
“Rotate Left” and press [OK].
≥The rotation information will be stored until the unit is turned 
off or the media is removed.
This function is only available for small-sized still pictures.
1While playing (except for slideshow)
Press [SUB MENU].
2Press [3,4] to select “Zoom out” and 
press [OK].
≥To cancel “Zoom out”, press [3,4] to select “Zoom in” in 
step 2 and press [OK].
≥The zoom-out information will not be stored.
∫BD-RE, DVD-RAM
To switch to another higher folder
(Only if there is a multiple number of higher folders 
recognizable)
1While the “Album View” screen is displayed
Press [SUB MENU].
2Press [3,4] to select “Select Root folder” 
and press [OK].
3Press [2,1] to select the higher folder 
and press [OK].
∫DVD-R/R DL, CD-R/RW
1While the “Picture View” screen is displayed
Press [SUB MENU]. 
2Press [3,4] to select “Select Folder” and 
press [OK].
3Press [3,4] to select a folder and press 
[OK].
While playing
Press [STATUS] twice.
≥It is also possible to display with the following procedures:
1Press [SUB MENU].
2Select “Status” with [3,4], and select [OK].
To exit, press [STATUS].
Rotate
Zoom out
To select the still pictures in another folder
\JPEG\DCIM001
OK 
RETURN 
Select Root folder
Change the Album folder to be accessed.
Press [OK] to confirm
e.g.,
To show the picture properties
PicturesFolder selection
CD(JPEG)
    001 
        002 
        003 
        004 
        005 
        006 
        007 
        
008        009 
        010 
      
    103 
        104 
        105
021216_0026   F  2/25
OK
RETURN
e.g.,
                                     
Photo     11/12/2009            Total        3/9
e.g., JPEG on DVD-RAM
Shooting date
DMPB15P-RQT9334_eng.book  19 ページ  ２００９年３月２８日　土曜日　午後２時３９分 
						

							RQT9334
(ENG )
20
Playing DivX® videos
 [DivX]
ABOUT DIVX VIDEO:DivX® is a digital video format created by DivX, Inc. This is an 
official DivX Certified device that plays DivX video.
You can play DVD-R/R DL and CD-R/RW discs which contain 
DivX video contents that have been recorded on a personal 
computer.
(About structure of folders D39, “Structure of folders that can 
be played in this unit”)
≥Because DivX format can use many different codecs, 
there is no guarantee that all DivX files will play. (>38, 
“About MP3/JPEG/DivX files”)
PreparationInsert a disc (>13).
1Press [AV SELECT] to select “DISC”.
≥If the media containing data in different file formats is 
inserted, the file selection menu may be displayed. 
Press [3,4] to select “Play Video (DivX)” and press 
[OK].
2Press [3,4] to select the title and press 
[OK].
Play starts on the selected title.
≥The picture sizes set for recording may prevent the unit from 
showing pictures in the proper aspect. You may be able to 
adjust the aspect through the TV.
≥Successive play is not possible.
≥You can use search and skip functions. (>15)
≥Press [:, 9] to show other pages.
(If the media contains data in different file formats)
1Press [FUNCTIONS].
2Press [3,4] to select “Menu” and press [OK].
3Press [3,4] to select “Play Video (DivX)” and press [OK].
1While the “DIRECT NAVIGATOR” is displayed
Press [SUB MENU].
2Press [3,4] to select “Select Folder” and 
press [OK].
3Press [3,4] to select a folder and press 
[OK].
≥You cannot select folders that contain no compatible files.
To return to the previous screenPress [RETURN].
ABOUT DIVX VIDEO-ON-DEMAND:This DivX® Certified device must be registered in order to play 
DivX Video-on-Demand (VOD) content. 
First generate the DivX VOD registration code for your device 
and submit it during the registration process. 
[Important: DivX VOD content is protected by a DivX DRM 
(Digital Rights Management) system that restricts playback to 
registered DivX Certified devices. If you try to play DivX VOD 
content not authorized for your device, the message 
“Authorization Error.” will be displayed and your content will not 
play.] Learn more at www.divx.com/vod.
Display the unit’s registration code.(>36, “DivX Registration” in “Others”)
≥After playing DivX VOD content for the first time, another 
registration code is then displayed in “DivX Registration”. Do 
not use this registration code to purchase DivX VOD content. 
If you use this code to purchase DivX VOD content, and then 
play the content on this unit, you will no longer be able to play 
any content that you purchased using the previous code.
≥If you purchase DivX VOD content using a registration code 
different from this unit’s code, you will not be able to play this 
content. (“Authorization Error.” is displayed.)
To switch from other menus to DivX menu
e.g., 
CD
Select an action or press [RETURN].OK
RETURN SUB
MENU
Play Pictures (JPEG)Play Video (DivX)
Play Music (MP3)
CD (DivX)
PlayRETURNSUB
MENU
DIRECT NAVIGATOR
NoName of Title
From SUB MENU you can select a folder.Page  01/01
001          ABC.divx
DivX
e.g., 
Playing a title in another folder
Regarding DivX VOD content
Selected folder No. /
Total folders
If the folder has no 
title, 
“– –” is displayed as 
folder number.CD (DivX)DIRECT NAVIGATORFolder selection
 Page  01/01
F   1/21
OKRETURN
Image001
Image002
Image003
Image004
Image005
Image006
Image007
Image008
Image009
Image010 12_02_2004
e.g., 
DivX Registration
DivX® Video  On  Demand
Your registration code is : XXXXXXXX
To learn more visit www.divx.com/vod
8 alphanumeric 
characters
DMPB15P-RQT9334_eng.book  20 ページ  ２００９年３月２８日　土曜日　午後２時３９分