Panasonic Dmc Fx33 Operating Instructions Manual

							Advanced (Playback)
71VQT1J82
lower. When you rotate the zoom lever 
towards [ ] [T], the magnification 
becomes higher.
 When you change the magnification, 
the zoom position indication A appears 
for about 1 second so that you can 
check the position of the enlarged 
section.
2Press 3/4/2/1 to move the 
position.
 When you move the position to be 
displayed, the zoom position indication 
appears for about 1 second.
∫To stop using the playback zoom
Rotate the zoom lever towards [ ] [W] or 
press [MENU/SET].
∫To delete a picture during the 
playback zoom
1Press [ ].
2Press 3 to select [YES].
3Press [MENU/SET].
 You can also delete the recording 
information etc. on the screen during 
playback zoom by pressing [DISPLAY].
 The more a picture is enlarged, the more 
its quality deteriorates.
 If you want to save the enlarged picture, 
use the trimming function. (P87)
 The playback zoom may not operate if 
pictures have been recorded with other 
equipment.
Playing Back Motion 
Pictures/Pictures with 
Audio
∫Motion pictures
Press 2/1 to select a picture 
with a motion picture icon [ ]/
[]/[]/[]/[ ]/
[ ] and then press 4 to play 
back.
AThe motion picture recording time
BMotion picture icon
 After playback starts, the elapsed 
playback time is displayed on the bottom 
right of the screen.
For example, 8 minutes and 30 seconds is 
displayed as [8m30s].
 The cursor displayed during 
playback is the same as 3/4/
2/1.
Stopping motion picture playback
Press 4.
Fast forwarding/Fast rewinding
Press and hold 2/1 during motion picture 
playback.
 The camera returns to normal motion 
picture playback when 2/1 is released.
To pause
Press 3 during motion picture playback.
 Press 3 again to cancel pause.
2: Fast rewind
1: Fast forward
B
A
DMC-FX33_ENG.book  71 ページ  ２００７年７月９日　月曜日　午後１２時５８分 
						

							Advanced (Playback)
72VQT1J82
Frame-by-frame forwarding/rewinding
Press 2/1 while pausing.
∫Pictures with audio
Press 2/1 to select a picture 
with the audio icon [ ] and then 
press 4 to play back.
 Refer to [AUDIO REC.] (P61) and 
[AUDIO DUB.] (P86) for information about 
how to create still pictures with audio.
 Sound can be heard through the speaker. 
Refer to [VOLUME] (P19) for information 
about how to adjust the volume in the 
[SETUP] menu.

The file format that can be played back with 
this camera is QuickTime Motion JPEG.
 Please note that the bundled software 
includes QuickTime to play back motion 
picture files created with the camera on 
the PC. (P91)
 Some QuickTime Motion JPEG files 
recorded by a PC or other equipment may 
not play back on the camera.
 If you play back motion pictures that have 
been recorded with other equipment, the 
picture quality may deteriorate or the 
pictures may not play back.
 When using a high capacity card, it is 
possible that fast rewinding may be slower 
than usual.

You cannot use the following functions with 
motion pictures and pictures with audio.
– Playback zoom
(While playing back or pausing motion 
pictures and while playing audio)
– [TITLE EDIT]/[ROTATE DISP.]/
[ROTATE]/[AUDIO DUB.] (Motion 
pictures only)
– [TEXT STAMP]/[RESIZE]/[TRIMMING]/
[ASPECT CONV.]
Creating still pictures 
from a motion picture
You can create a single still picture (with 1 
screen or 9 screens) from a recorded 
motion picture. This is effective in moving 
scenes when you want to look carefully at 
the movement of a sportsperson etc.
1Press 2/1 to select a picture 
with a motion picture icon [ ]/
[]/[]/[]/[ ]/
[ ] and then press 4 to play 
back.
2Press 3 to pause motion picture 
playback.
 Press 3 again to return to motion 
picture playback.
 Press 2/1 while paused to move 
forward frame-by-frame.
 If you press the shutter button, you can 
save the displayed still pictures as one 
single picture. (Perform step
3)
DMC-FX33_ENG.book  72 ページ  ２００７年７月９日　月曜日　午後１２時５８分 
						

							Advanced (Playback)
73VQT1J82
∫Saving a single still picture with 
9 screens from the motion picture
 Rotate the zoom lever towards [ ] 
[W] to display the 9 screens playback 
screen.
 Rotate the zoom lever further towards 
[ ] (W) to switch to [ ]/[ ]/[ ] 
(A).
When a motion picture with [ ], 
[ ] or [ ] was selected
The recorded motion picture is created 
using 30 still picture frames per second.
When a motion picture with [ ], 
[ ]or [ ] was selected 
The recorded motion picture is created 
using 10 still picture frames per second.  You can move forward frame-by-frame 
by pressing 3/4/2/1.
3/4: Move forward/backward 3 frames 
at a time.
2/1: Move forward/backward 1 frame 
at a time.
3Press the shutter button. The message [SAVE THESE NINE 
PICTURES AS ONE SINGLE 
PICTURE ?] appears. Also, the 
message [SAVE AS A SINGLE 
PICTURE ?] appears if you saved the 
picture in step
2.
4Press 3 to select [YES] and then 
press [MENU/SET].
 The nine pictures are saved as one 
single picture.
∫To stop using the 9 screens playback 
screen
After the 9 screens playback screen is 
displayed, rotate the zoom lever several 
times towards [ ] (T) or press [MENU/
SET]. The screen returns to the paused 
motion picture playback screen.
∫Picture size
 [QUALITY] is fixed to [ ].
 You may not be able to save still pictures 
from a motion picture taken on other 
equipment. []All the frames of the recorded 
motion picture are displayed as 
still pictures (1/30th second 
intervals)
[]1 frame is skipped/every second 
frame is displayed as a still picture 
(1/15th second intervals)
[]2 frames are skipped/every third 
frame is displayed as a still picture 
(1/10th second intervals)
[]5 frames are skipped/every sixth 
frame is displayed as a still picture 
(1/5th second intervals)
[]All the frames of the recorded 
motion picture are displayed as 
still pictures (1/10th second 
intervals)
[]1 frame is skipped/every second 
frame is displayed as a still picture 
(1/5th second intervals)
A
Item1picture9pictures
[30fpsVGA]
0.3M 2M
[10fpsVGA]0.3M 2M
[30fpsQVGA]0.3M 1M
[10fpsQVGA]0.3M 1M
[30fps16:9]2M 2M
[10fps16:9]2M 2M
/SETMENU
DMC-FX33_ENG.book  73 ページ  ２００７年７月９日　月曜日　午後１２時５８分 
						

							Advanced (Playback)
74VQT1J82
Using the [PLAY] mode 
menu
You can use various functions in playback 
mode to rotate pictures, set protection for 
them etc.
1Press [MENU/SET].
2Press 3/4 to select the menu 
item and then press 1.
 Press 4 at A to switch to the next 
menu screen.
 You can switch menu screens from any 
menu item by rotating the zoom lever.
After performing steps 
1 and 2, refer 
to the description of the menu item 
in the operating instructions and 
then set it.Items that can be set
 With [TEXT STAMP], [RESIZE], 
[TRIMMING] or [ASPECT CONV.], a new 
edited picture is created. A new picture 
cannot be created if there is no free space 
on the built-in memory or the card so we 
recommend checking that there is free 
space and then editing the picture.
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P74)
This is recommended when playing back 
pictures on a TV screen. You can skip 
unwanted pictures if [FAVORITE] (P79) has 
been set.  Also, you can play back a 
recorded category slide show (P77).
A
Menu 
screenItem
1/3: [SLIDE SHOW] (P74)
: [CATEGORY] (P76)
: [ROTATE DISP.] (P78)
: [ROTATE] (P78)
: [FAVORITE] (P79)
2/3: [TITLE EDIT] (P79)
: [TEXT STAMP] (P81)
: [DPOF PRINT] (P83)
: [PROTECT] (P85)
: [AUDIO DUB.] (P86)
3/3: [RESIZE] (P86)
: [TRIMMING] (P87)
:
[ASPECT CONV.] (P88)
: [COPY] (P89)
: [FORMAT] (P90)
[SLIDE SHOW]
Playing back pictures in order for a 
fixed duration
/SETMENU
DMC-FX33_ENG.book  74 ページ  ２００７年７月９日　月曜日　午後１２時５８分 
						

							Advanced (Playback)
75VQT1J82
1Press 3/4 to select [ALL], [ ] or 
[ ] and then press [MENU/SET].
 [ ] appears only when [FAVORITE] is 
set to [ON]. If none of the pictures have 
[ ] displayed, you cannot select [ ] 
even if [FAVORITE] is set to [ON].
 You cannot select [ ] if a category 
slide show is not recorded.
2Press 3 to select [START] and 
then press [MENU/SET].
(Screen when [ALL] is selected)
 The cursor displayed during a slide 
show A or while a slide show is paused 
B or during [MANUAL] slide show C is 
the same as 3/4/2/1.
3 to pause the slide show. Press 
3 again to cancel pause.
2/1 while paused to display the 
previous or next picture.
3Press 4 to finish.
∫Setting the audio, duration and effect
Select [DURATION], [EFFECT] or [AUDIO] 
on the screen shown in step
2 and set.
 If you set [AUDIO] to [ON] and then play 
back a picture with audio, the next picture 
will be displayed after the audio has 
finished.
 You cannot play back motion pictures and 
use power save in a slide show. (However, 
the setting for power save mode is fixed to 
[10MIN.] while pausing a slide show or 
playing back a manual slide show.) [ALL]Displays all pictures.
[]Displays only those pictures 
that have been set as 
favorites (P79).
[]Displays only if a category 
slideshow is recorded in 
[CATEGORY] (P76).
/SETMENU
/SETMENU
[DURATION]Can be set to [1SEC.], 
[2SEC.], [3SEC.], 
[5SEC.] or [MANUAL] 
(manual playback).
 You can only select 
[MANUAL] when [ ] or 
[ ] has been 
selected in step
1.
2/1 to display 
the previous or next 
picture when [MANUAL] 
is selected.
[EFFECT]A slide show effect can 
be selected.
[OFF]:No effect
:
New pictures slide 
across the screen.
:Current pictures 
fade out and new 
pictures fade in.
:New pictures 
gradually fill the screen 
from the center.
:An effect is selected 
at random.
 If you set [DURATION] 
to [MANUAL] the 
settings in [EFFECT] 
are disabled.
[AUDIO]If set to [ON], the audio 
of the pictures with audio 
is played back.
DMC-FX33_ENG.book  75 ページ  ２００７年７月９日　月曜日　午後１２時５８分 
						

							Advanced (Playback)
76VQT1J82
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P74)
This mode allows you to search the 
recording information in scene modes etc. 
([PORTRAIT], [SCENERY], 
[NIGHT SCENERY] etc.) and sort the 
pictures into different categories. You can 
then play back the pictures in each 
category normally or as a slide show.
Press 1 to search the categories.
 If a picture is found in a category, the 
category icon turns blue.
 It may take time to search the picture 
files if there are a lot on the card or the 
built-in memory.
 If you press [ ] while searching, the 
searching will stop halfway.
 Pictures are sorted into the categories 
shown below.¢The travel dates of images in the 
clipboard folder are not categorized.
1Press 3/4/2/1 to select the 
category to play back and then 
press [MENU/SET] to set.
2Press 2/1 to select the picture.
 Rotate the zoom lever towards [ ] 
(W) to display 9 screens and rotate the 
zoom lever towards [ ] (T) to enlarge 
the picture up to 16a.
 You can record pictures as favorites by 
pressing 3 if [FAVORITE] is set to 
[ON].
 Pictures cannot be deleted during 
category playback even if you press 
[].
[CATEGORY]
Searching by recording information
[CATEGORY]Recording information 
e.g. scene modes
(Portrait etc.)
[PORTRAIT], 
[i-PORTRAIT], 
[SOFT SKIN], 
[SELF PORTRAIT], 
[NIGHT PORTRAIT], 
[i-NIGHT PORTRAIT],  
[BABY1]/[BABY2]
(Scenery 
etc.)[SCENERY], 
[i-NIGHT SCENERY], 
[SUNSET], 
[AERIAL PHOTO] 
(Night 
scenery etc.)[NIGHT PORTRAIT], 
[i-NIGHT PORTRAIT],  
[NIGHT SCENERY], 
[i-NIGHT SCENERY], 
[STARRY SKY]
/SETMENU(Event)[SPORTS], [PARTY], 
[CANDLE LIGHT], 
[FIREWORKS], 
[BEACH], [SNOW], 
[AERIAL PHOTO]
[BABY1]/[BABY2]
[PET]
[FOOD]
[UNDERWATER]
[TRAVEL DATE]¢
[MOTION PICTURE]
/SETMENU
DMC-FX33_ENG.book  76 ページ  ２００７年７月９日　月曜日　午後１２時５８分 
						

							Advanced (Playback)
77VQT1J82
3Press [MENU/SET] twice to close 
the menu.
∫Playing back a slide show
1Press 3/4/2/1 to select the 
category to play back and then 
press [DISPLAY]. 
2Press 3 to select [START] and 
then press [MENU/SET].
3 during a slide show to pause 
it. Press 3 again to cancel pause.
2/1 while paused to display the 
previous or next picture.
 Refer to P75 for information about 
setting [DURATION], [EFFECT] and 
[AUDIO].
3Press 4 to finish the slide show.
4Press [MENU/SET] twice to close 
the menu.
∫Recording a slide show
If you record a category slide show, you 
can play it back by selecting [ ] in 
[SLIDE SHOW] on page 74.
1Press 4 to select [SLIDESHOW 
SETUP] 
and then press [MENU/
SET].
2Press 3 to select [YES] and then 
press [MENU/SET].
 You can only record one category slide 
show on one card. If a category slide 
show has already been recorded, the 
message [A CATEGORY SLIDESHOW 
ALREADY EXISTS. OVERWRITE?] 
appears.
 If there are 1000 or more pictures, you 
can make a slide show with up to 999 
pictures.
3Press 2 to return to the category 
playback screen.
 Press [ ] and then press [MENU/SET] 
to close the menu.
 You cannot play back motion pictures as a 
slide show. 
 Still pictures created from a motion picture 
(P72) cannot be played back from the 
motion pictures category   in category 
playback.
/SETMENU
/SETMENU
/SETMENU
DMC-FX33_ENG.book  77 ページ  ２００７年７月９日　月曜日　午後１２時５８分 
						

							Advanced (Playback)
78VQT1J82
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P74)
This mode allows you to automatically 
display pictures vertically if they were 
recorded holding the camera vertically or 
rotate pictures manually in 90° steps.
∫Rotate display
(The picture is automatically rotated and 
displayed.)
1Press 4 to select [ON] and then 
press [MENU/SET].
 The pictures are displayed without 
being rotated when you select [OFF].
 Refer to P28 for information about how 
to play back pictures.
2Press [MENU/SET] to close the 
menu.
∫Rotate
(The picture is rotated manually.)
1Press 2/1 to select the picture 
and then press 4.
 The [ROTATE] function is disabled 
when [ROTATE DISP.] is set to [OFF].
 Motion pictures and protected pictures 
cannot be rotated.
2Press 3/4 to select the direction 
to rotate the picture and then 
press [MENU/SET].
3Press [MENU/SET] twice to close 
the menu.
 If you take pictures when aiming the 
camera up or down, it may not be possible 
to display the pictures vertically.
 The picture may be slightly blurred when 
the camera is connected to the TV with 
the AV cable (supplied) and played back 
ver tically.
 When you play back pictures on a PC, 
they cannot be displayed in the rotated 
direction unless the OS or software is 
compatible with Exif. Exif is a file format 
for still pictures which allows recording 
information etc. to be added. It was 
established by “JEITA (Japan Electronics 
and Information Technology Industries 
Association)”.
 Rotated pictures are displayed rotated 
when they are played back in review 
playback and playback zoom however are 
displayed without being rotated when they 
are played back in multi playback.
 It may not be possible to rotate pictures 
that have been recorded with other 
equipment.
[ROTATE DISP.]/[ROTATE]
To display the picture rotated
/SETMENU
/SETMENU
The picture rotates clockwise in 
steps of 90°.
The picture rotates 
counter-clockwise in steps of 90°.
/SETMENU
DMC-FX33_ENG.book  78 ページ  ２００７年７月９日　月曜日　午後１２時５８分 
						

							Advanced (Playback)
79VQT1J82
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P74)
You can do the following if a mark has been 
added to pictures and they have been set 
as favorites.
 Delete all the pictures not set as favorites. 
([ALL DELETE EXCEPT ])
 Play back the pictures set as favorites only 
as a slide show.
1Press 4 to select [ON] and then 
press [MENU/SET].
 You cannot set pictures as favorites if 
[FAVORITE] is set to [OFF]. Also the 
favorites icon [ ] will not appear when 
[FAVORITE] is set to [OFF] even if it 
was previously set to [ON].
 You cannot select [CANCEL] if none of 
the pictures have [ ] displayed.
2Press [MENU/SET] to close the 
menu.
3Press 2/1 to select the picture 
then press 3.
 Repeat the above procedure.
3 is pressed while the [ ] favorites 
icon A is displayed, [ ] is cleared, and 
the favorites setting is canceled.
 You can set up to 999 pictures as 
favor ites .
∫Deleting all favorites
1Select [CANCEL] on the screen shown 
in step 
1 and then press [MENU/SET].
2Press 3 to select [YES] and then press 
[MENU/SET].
3Press [MENU/SET] to close the menu.
 When printing pictures at a photo printing 
store, [ALL DELETE EXCEPT ] (P29) is 
useful so only the pictures you want to be 
printed remain on the card.
 Use [LUMIX Simple Viewer] or 
[PHOTOfunSTUDIO-viewer-] on the 
CD-ROM (supplied), to set, confirm or 
delete favorites. [For details, refer to the 
operating instructions (PDF file) of the 
software.]
 You may not be able to set pictures taken 
with other equipment as favorites.
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P74)
You can add text (comments) to pictures. 
After text has been registered, it can be 
included in prints using [TEXT STAMP]  
(P81). (Only alphabetic characters and 
symbols can be entered.)
Press 3/4 to select [SINGLE] or 
[MULTI] and then press [MENU/
SET].
[FAVORITE]
Setting your favorite pictures
/SETMENU
/SETMENU
A
[TITLE EDIT]
Adding text (comments) to pictures
/SETMENU
/SETMENU
DMC-FX33_ENG.book  79 ページ  ２００７年７月９日　月曜日　午後１２時５８分 
						

							Advanced (Playback)
80VQT1J82
∫Single setting
1Press 2/1 to select a picture and 
then press 4.
 The title edit icon [ ] is displayed for 
pictures that have already been 
recorded with text in [BABY1]/[BABY2] 
(P45) or [PET] (P46) name settings in 
scene mode or [TITLE EDIT].
2Press 3/4/2/1 to select text 
and then press [MENU/SET] to 
register.
 Refer to the P81 for an example of the 
text entry.
 Press [DISPLAY] to switch text 
between [A] (capitals), [a] (small case) 
and [&/1] (special characters and 
numbers).
 The cursor at the entry position can be 
moved to the left with [ ], and to the 
right with [ ].
 To enter a blank, move the cursor to 
[SPACE], and press [MENU/SET].
 To stop editing at any time during text 
entry, press [ ].
To delete an entered character, 
move the cursor to [DELETE], and 
press [MENU/SET].
 A maximum of 30 characters can be 
entered.
3Press 3/4/2/1 to move the 
cursor to [EXIT] and then press 
[MENU/SET] to end text input.
4Press [MENU/SET] twice to close 
the menu.
∫Multi setting
1Press 2/1 to select the picture 
and then press 4 to SET/
CANCEL.
 Repeat this step.
 Titles cannot be changed or deleted in 
[MULTI].
2Press [MENU/SET].
After performing step 2, perform 
step 2 onwards in “Single setting” 
(P80).
∫Delete the title (for [SINGLE] only)
1In step 2 when [SINGLE] (P80) is 
selected, delete all the texts, select 
[EXIT], and press [MENU/SET].
2Press [MENU/SET] twice to close the 
menu.
/SETMENU
[SET]The [TITLE EDIT] icon A 
appears.
[CANCEL]The [TITLE EDIT] icon A 
disappears.
A
DMC-FX33_ENG.book  80 ページ  ２００７年７月９日　月曜日　午後１２時５８分