Panasonic Dmc Fx01 Operating Instructions Manual

							Menu Settings
71VQT0V86
 If none of the pictures have [ ] 
displayed, you cannot select [ ] even 
if [FAVORITE] is set to [ON].
2Press 3 to select [START] and 
then press [MENU/SET].
(Screen when [ALL] is selected)
 The cursor displayed during a slide 
show A or while a slide show is paused 
B or during [MANUAL] slide show C is 
the same as 3/4/2/1.
Press 3 to pause the slide show. Press 
3 again to cancel pause.
Press 2/1 while paused to display the 
previous or next picture.
3Press 4 to finish.
∫Setting the audio and duration
Select [DURATION] or [AUDIO] on the 
screen shown in step 2 and set.
 You can only select [MANUAL] when 
[ ] has been selected in step 1.
Press 2/1 to display the previous or 
next picture when [MANUAL] is 
selected. If you set [AUDIO] to [ON] and then play 
back a picture with audio, the next picture 
will be displayed after the audio has 
finished.
 You cannot play back motion pictures and 
use power save in a slide show. (However, 
the setting for power save mode is fixed to 
[10MIN.] while pausing a slide show or 
playing back a manual slide show.)
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P70)
You can do the following if a mark has been 
added to pictures and they have been set 
as favorites.
 Delete all the pictures not set as favorites. 
([ALL DELETE EXCEPT ]) (P31)
 Play back the pictures set as favorites only 
as a slide show. (P70)
1Press 4 to select [ON] and then 
press [MENU/SET].
 You cannot set pictures as favorites if 
[FAVORITE] is set to [OFF]. Also the 
favorites icon [ ] will not appear when 
[FAVORITE] is set to [OFF] even if it 
was previously set to [ON].
 You cannot select [CANCEL] if none of 
the pictures have [ ] displayed.
2Press [MENU/SET] to close the 
menu.
[DURATION] Can be set to [1SEC.], 
[2SEC.], [3SEC.], 
[5SEC.] or [MANUAL] 
(manual playback).
[AUDIO] If set to [ON], the audio 
of the pictures with audio 
is played back.
SLIDE SHOW
SETSELECTMENUCANCEL
START
AUDIO1 SEC.OFFDURATION
/SETMENU[FAVORITE]
Setting your favorite pictures
/SETMENU
PLAY1/3
ON OFF
SETMENUDPOF PRINT
ROTATE DISP.ROTATE
SLIDE SHOW
ON OFFCANCEL
FAVORITE
SELECT/SETMENU
VQT0V86ENG.book  71 ページ  ２００６年１月３０日　月曜日　午前９時４６分 
						

							Menu Settings
72VQT0V86
3Press  21 to select the picture 
then press 3.
 Repeat the above procedure.
If  3 is pressed while the [ ] favorites 
icon  A is displayed, [ ] is cleared, and 
the favorites setting is canceled.
 You can set up to 999 pictures as  favorites.
∫ Deleting all favorites
1 Select [CANCEL] on the screen shown in 
step 1 and then press [MENU/SET].
2 Press  3 to select [YES] and then press 
[MENU/SET].
3 Press [MENU/SET] to close the menu.
 When printing pictures at a photo printing 
store, [ALL DELETE EXCEPT ] (P31) is 
useful so only the pictures you want to be 
printed remain on the card.
 Use [LUMIX Simple Viewer] on the  CD-ROM (supplied), to set, confirm or 
delete favorites. (For information about 
this, refer to the separate operating 
instructions for PC connection.)
 You may not be able to set pictures taken 
with other equipment as favorites. Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P70)
This mode allows you to automatically 
display pictures vertically if they were 
recorded holding the camera vertically or 
rotate pictures manually in 90° steps.
∫
Rotate display
(The picture is automatically rotated 
and displayed.)
1Press  4 to select [ON] and then 
press [MENU/SET].
 The pictures are displayed without 
being rotated when you select [OFF].
 Refer to P30 for information about how  to play back pictures.
2 Press [MENU/SET] to close the 
menu.
∫ Rotate
(The picture is rotated manually.)
1Press  21 to select the picture 
and then press 4.
 The [ROTATE] function is disabled 
when [ROTATE DISP.] is set to [OFF].
 Motion pictures and protected pictures  cannot be rotated.
1/3
10:00  DEC. 1.2006
[ROTATE DISP.]/[ROTATE]
To display the picture rotated
/SETMENU
PLAY1/3
ON
OFF
SETMENU
OFF
ON
DPOF PRINT
FAVORITEROTATE DISP.ROTATE
SLIDE SHOW
SELECT/SETMENU
ROTATE
SELECT
SET
1/3
EXITMENU
VQT0V86ENG.book  72 ページ  ２００６年１月３０日　月曜日　午前９時４６分 
						

							Menu Settings
73VQT0V86
2Press 34 to select the direction 
to rotate the picture and then 
press [MENU/SET].
3Press [MENU/SET] twice to close 
the menu.
∫Example
When rotating clockwise ( )
Original
picture
 When [ROTATE DISP.] is set to [ON], 
pictures recorded holding the camera 
vertically are played back vertically (rotated).
 If you take pictures when aiming the 
camera up or down, it may not be possible 
to display the pictures vertically. (P23)
 The picture may be slightly blurred when 
the camera is connected to the TV with 
the AV cable (supplied) and played back 
vertically.
 When you play back pictures on a PC, they 
cannot be displayed in the rotated direction 
unless the OS or software is compatible with 
Exif. Exif is a file format for still pictures 
which allows recording information etc. to be 
added. It was established by JEITA [Japan Electronics and Information Technology 
Industries Association].
 Rotated pictures are displayed rotated 
when they are played back in review 
playback and playback zoom however are 
displayed without being rotated when they 
are played back in multi playback.
 It may not be possible to rotate pictures 
that have been recorded with other 
equipment.
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P70)
DPOF (Digital Print Order Format) is a 
system that allows the user to select which 
pictures to print, how many copies of each 
picture to print and whether or not to print 
the recording date on the pictures when 
using a DPOF compatible photo printer or 
photo printing store. For details, ask at your 
photo printing store.
For more information visit:
http://panasonic.jp/dc/dpof_110/
white_e.htm
Press 34 to select [SINGLE], 
[MULTI] or [CANCEL] and then 
press [MENU/SET].
 You cannot select [CANCEL] if there 
are no prints that have been set in the 
DPOF print settings. The picture rotates clockwise in 
steps of 90°.
The picture rotates 
counter-clockwise in steps of 90°.
ROTATE
SELECTSETMENUCANCEL/SETMENU
[DPOF PRINT]
Setting the picture to print and the 
number of prints
/SETMENU
PLAY1/3
ON OFFFAVORITEROTATE DISP.ROTATE
SLIDE SHOW
SINGLE
MULTI
CANCELDPOF PRINT/SETMENUSETMENUSELECT
VQT0V86ENG.book  73 ページ  ２００６年１月３０日　月曜日　午前９時４６分 
						

							Menu Settings
74VQT0V86
∫Single setting
1Press  21 to select the picture 
to print and then press  34 to 
set the number of prints.
 The number of prints icon [ ] 
appears.
 The number of prints can be set from 
0 to 999. The DPOF print setting is 
canceled when the number of prints is 
set to “0”.
2 Press [MENU/SET] twice to close 
the menu.
∫ Multi setting
1Press  21 to select the picture 
to print then press  34 to set 
the number of prints.
 The number of prints icon [ ] 
appears.
 Repeat the above procedure. (You  cannot set all the pictures at one time.)
 The number of prints can be set from 
0 to 999. The DPOF print setting is 
canceled when the number of prints is 
set to “0”.
2 Press [MENU/SET] twice to close 
the menu.
∫ To cancel all settings
1Press  3 to select [YES] and then 
press [MENU/SET].
2 Press [MENU/SET] to close the 
menu.
∫ To print the date
After setting the number of prints, set/
cancel printing with the recording date by 
pressing [DISPLAY].
 The date print icon [ ] appears.
 When you go to a photo printing store for 
digital printing, be sure to order the 
printing of the date additionally if required.
 Depending on the photo printing store or 
the printer, the date may not be printed 
even if you set to print the date. For further 
information, ask at your photo printing 
store or refer to the operating instructions 
for the printer.
DATEDISPLAY
1DPOF SET THIS
COUNT1SELECT
1/14
EXITMENU
DATEDISPLAYCOUNT1
7918
1112
DPOF SET MULTI
10
SELECTEXITMENU
CANCEL ALL DPOF
CANCEL ALL DPOF
PRINT SETTINGS?
SELECTSET
NOYES
MENU/SETMENU
DATEDISPLAY
DPOF SET THIS1
COUNT1
1/14
SELECTEXITMENU
DATE
DATE
VQT0V86ENG.book  74 ページ  ２００６年１月３０日　月曜日　午前９時４６分 
						

							Menu Settings
75VQT0V86
 DPOF is an abbreviation of [Digital Print 
Order Format]. This feature allows you to 
write print information to media and then 
use the information on a DPOF-compliant 
system.
 DPOF print setting is a convenient 
function when printing pictures with a 
printer that supports PictBridge (P82). 
The date printing setting on the printer 
may take priority over the date printing 
setting on the camera. Check the date 
printing setting on the printer also. (P82)
 It is necessary to delete all previous 
DPOF print information made on other 
equipment when setting DPOF print on 
the camera.
 If the file is not based on the DCF 
standard, the DPOF print setting cannot 
be set. DCF is an abbreviation of [Design 
rule for Camera File system], stipulated by 
JEITA [Japan Electronics and Information 
Technology Industries Association].
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P70)
You can set protection for pictures you do 
not want to be deleted by mistake.
Press 34 to select [SINGLE], 
[MULTI] or [CANCEL] and then 
press [MENU/SET].
∫Single setting
1Press 21 to select the picture 
and then press 4 to set/cancel.
2Press [MENU/SET] twice to close 
the menu.
∫Multi setting/To cancel all settings
Perform the same operation as in 
“[DPOF PRINT] Setting the picture to print 
and the number of prints”. (P73 to 75)
 If you press [MENU/SET] while canceling 
protection, the canceling will stop halfway.
 The protect setting may not be effective 
on other equipment.
 If you want to delete protected pictures, 
cancel their protection.
 Even if you protect pictures on a card, 
they will be deleted if the card is 
formatted. (P79)
 Even if you do not protect pictures on an 
SD Memory Card, they cannot be deleted 
when the card’s write protect switch A is 
set to [LOCK].
 The following functions cannot be used 
with protected pictures.
–[ROTATE]
–[AUDIO DUB.][PROTECT]
Preventing accidental erasure of 
pictures
/SETMENU
PLAY2/3
ON OFFRESIZETRIMMING
AUDIO DUB.SINGLE
MULTI
CANCELPROTECT
SETMENUSELECTASPECT CONV./SETMENU
SET The protect icon [ ] appears.
CANCEL The protect icon [ ] 
disappears.
SET/CANCEL
PROTECT THIS
SELECT
1/3100_
0001
EXITMENU
16
VQT0V86ENG.book  75 ページ  ２００６年１月３０日　月曜日　午前９時４６分 
						

							Menu Settings
76VQT0V86
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P70)
You can add the audio after taking a 
picture.
1Press  21 to select the picture 
and then press  4 to start audio 
recording.
 The message [OVERWRITE AUDIO 
DATA?] screen appears when audio has 
already been recorded. Press  3 to 
select [YES] and then press [MENU/
SET] to start audio recording. (The 
original audio is overwritten.)
 Audio dubbing cannot be used with the  following pictures.
– Motion pictures
– Protected pictures
 Audio dubbing may not work properly on 
pictures recorded by other equipment.
2 Press  4 to stop recording.
 The audio recording stops 
automatically if  4 is not pressed after 
about 10 seconds.
3 Press [MENU/SET] twice to close 
the menu.
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P70)
This function is useful if you want to reduce 
the file size of a picture to attach it to an 
e-mail or upload it to a website.
1Press  21 to select the picture 
and then press 4.
 The following pictures cannot be 
resized.
 When the aspect ratio setting is [ ].– Pictures recorded in [ ] (0.3M EZ)
 When the aspect ratio setting is 
[].
– Pictures recorded in [ ]  (2.5M EZ)
 When the aspect ratio setting is  [].
– Pictures recorded in [ ] (2M EZ)
– Motion pictures
– Pictures with audio
 It may not be possible to resize pictures 
recorded with other equipment.
2 Press  21 to select the size and 
then press 4.
 Sizes smaller than the recorded picture 
are displayed.
[AUDIO DUB.] 
Adding audio after taking pictures
/SETMENU
AUDIODUB.
STARTSELECT
1/3100 _
0001
EXITMENU
AUDIODUB.
STOP
1/3100 _
0001
[RESIZE]
Making the picture smaller
/SETMENU
RESIZE
EXITSET SELECT
1/3
MENU
RESIZE
EXITRESIZE SELECT
1/3
MENU
VQT0V86ENG.book  76 ページ  ２００６年１月３０日　月曜日　午前９時４６分 
						

							Menu Settings
77VQT0V86
 When the aspect ratio setting is [ ].– [ ]/[ ]/[ ]/[ ]
 When the aspect ratio setting is  [].
–[ ]
 When the aspect ratio setting is  [].
–[ ]
 The message [DELETE ORIGINAL  PICTURE?] appears.
3 Press 3 4 to select [YES] or 
[NO] and then press [MENU/SET].
 The picture is overwritten when you 
select [YES]. Resized pictures cannot 
be restored when they are overwritten.
 A resized picture is newly created when  you select [NO].
 If the original picture is protected, you  cannot overwrite it. Select [NO] and 
newly create a resized picture.
4 Press [MENU/SET] twice to close 
the menu.
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P70)
You can enlarge and then clip the important 
part of the recorded picture.
1Press  21 to select the picture 
and then press 4.
 The following pictures cannot be 
trimmed.
– Motion pictures
– Pictures with audio
 It may not be possible to trim pictures  recorded with other equipment.
2 Enlarge or decrease the parts to 
be trimmed with the zoom lever.
3Press  3/4/2/ 1 to move the 
position of the part to be trimmed.
4 Press shutter button.
 The message [DELETE ORIGINAL 
PICTURE?] appears.
RESIZE
DELETE ORIGINAL
PICTURE?
NOYES
SETMENUSELECTCANCEL/SETMENU
[TRIMMING]
Enlarging a picture and trimming it
/SETMENU
TRIMMING
EXITSELECTSET
1/3
MENU
ZOOMEXIT
TRIMMING
1/3
MENU
TW
TRIM:SHUTTER ZOOMEXIT
TRIMMING
1/3
MENU
VQT0V86ENG.book  77 ページ  ２００６年１月３０日　月曜日　午前９時４６分 
						

							Menu Settings
78VQT0V86
5Press  34 to select [YES] or 
[NO] and then press [MENU/SET].
 The picture is overwritten when you 
select [YES]. The trimmed pictures 
cannot be restored when they are 
overwritten.
 A trimmed picture is newly created 
when you select [NO].
 When the original picture is protected,  you cannot overwrite it. Select [NO] and 
newly create a trimmed picture.
6 Press [MENU/SET] twice to close 
the menu.
\
 Depending on the cut size, the picture size 
of the trimmed picture may become 
smaller than that of the original picture.
 The picture quality of the trimmed picture  will deteriorate.
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P70)
You can convert pictures taken with a 
[ ] aspect ratio to a [ ] or a [ ] 
aspect ratio.
1 Press  3/4 to select [ ] or 
[ ] and then press [MENU/
SET].
 Only pictures taken with a [ ] 
aspect ratio can be converted.
 You may not be able to convert pictures  taken on other equipment.
2 Press  2/1 to select a picture and 
then press 4.
 If you select and set a picture with an 
aspect ratio other than [ ], the 
message [CANNOT BE SET ON THIS 
PICTURE] is displayed on the screen.
3 Press  21 to determine the 
horizontal position and press the 
shutter button to set.
 Use  3/4 to set the frame position for 
pictures rotated vertically.
 The message [DELETE ORIGINAL  PICTURE?] appears.
[ASPECT CONV.]
Changing the aspect ratio of a 16:9 
picture
DELETE ORIGINAL
PICTURE?
TRIMMING
NO
SELECTSETMENUCANCEL
YES
/SETMENU
/SETMENU
PLAY2/3
RESIZETRIMMING
AUDIO DUB.PROTECT
SETMENUSELECT/SETMENUASPECT CONV.
SETSELECT
ASPECTCONV.100
_
00011/3
EXITMENU
EXITMENUSET : SHUTTER ADJUST.
VQT0V86ENG.book  78 ページ  ２００６年１月３０日　月曜日　午前９時４６分 
						

							Menu Settings
79VQT0V86
4Press 3/ 4 to select [YES] or 
[NO] and then press [MENU/SET].
 The picture is overwritten when you 
select [YES]. If you convert the aspect 
ratio of a picture and then overwrite it, 
you cannot restore it.
 A picture with the converted aspect ratio  is newly created when you select [NO].
 When the original picture is protected, you cannot overwrite it. Select [NO] and 
newly create a picture with the 
converted aspect ratio.
5 Press [MENU/SET] twice to close 
the menu.
 After converting the aspect ratio, the 
picture size may become larger than that 
of the original picture.
 The following pictures cannot be 
converted.
– Pictures with audio
– Motion pictures
 Files that do not conform to the DCF  standard cannot be converted. DCF is an 
abbreviation of [Design rule for Camera 
File system], stipulated by JEITA [Japan 
Electronics and Information Technology 
Industries Association]. Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P70)
Usually, it is not necessary to format the 
card. Format it when the message 
[MEMORY CARD ERROR] appears.
Press 
3 to select [YES] and then 
press [MENU/SET].
 Formatting irretrievably deletes all the 
data including any protected pictures. 
Check the data carefully before 
formatting.
 If the card has been formatted on a PC or  other equipment, format it on the camera 
again.
 Use a battery with sufficient battery power  (P12) or the AC adaptor (DMW-AC5; 
optional) when formatting.
 Do not turn the camera off during  formatting.
 You cannot format an SD Memory Card 
when the card’s write protect switch is set 
to [LOCK].
 If the card cannot be formatted, consult 
your nearest servicenter.
DELETE ORIGINAL
PICTURE?
ASPECT CONV.
NOYES
/SETMENUSELECTSETMENUCANCEL
[FORMAT] 
Initializing the card
/SETMENU
FORMAT
DELETE ALL DATA
ON THE MEMORY CARD?
NOYES
SELECTSETMENU/SETMENU
For USA assistance, please call: 1-800-272-7033 
or send e-mail to : [email protected]
For Canadian assistance, please call:
1-800-561-5505 or visit us at www.panasonic.ca
VQT0V86ENG.book  79 ページ  ２００６年１月３０日　月曜日　午前９時４６分 
						

							Connecting to other equipment
80VQT0V86
Connecting to other equipment
Connecting to a PC
You can acquire recorded pictures to a PC 
by connecting the camera and the PC.
The software [LUMIX Simple Viewer] 
(for Windows
®) in the CD-ROM (supplied) 
allows you to easily acquire pictures 
recorded with the camera to a PC, print 
them and send them by e-mail.
If you use Windows
 98/98SE, install the 
USB driver and then connect it to the 
computer.
For information about installing [LUMIX 
Simple Viewer] etc., refer to the separate 
operating instructions for PC connection.
A: USB connection cable (supplied)
B: AC adaptor (DMW-AC5; optional)
 Use a battery with sufficient battery power 
or the AC adaptor (DMW-AC5; optional). Turn the camera off before inserting or 
removing the cable for the AC adaptor 
(DMW-AC5; optional).
1Turn on the camera and the PC.
2Connect the camera to a PC via 
the USB connection cable A 
(supplied).
 Connect the USB connection cable with 
the [ ] mark facing the [2] mark on 
the [DIGITAL] socket.
 Hold the USB connection cable at C 
and insert straight in or take straight 
out. (If you forcibly insert the USB 
connection cable at a slant or upside 
down you can deform the connection 
terminals and damage the camera or 
the connected equipment.)
D: This message appears during data 
transfer.
3Press 3 to select [PC] and then 
press [MENU/SET].
 If you set [USB MODE] in the [SETUP] 
menu to [PC] in advance, it is not 
necessary to set this every time you 
connect to a PC. (P20)
 If you set [USB MODE] to [PictBridge 
(PTP)] and then connect the camera to 
the PC, messages may appear on the 
screen of the PC.
DIGITAL
AV OUT
DC IN
ACCESS
USB MODE
SELECTSETMENUPictBridge(PTP)PC
PLEASE SELECT
THE USB MODE.
/SETMENU
VQT0V86ENG.book  80 ページ  ２００６年１月３０日　月曜日　午前９時４６分