Panasonic Dmc Fs7 Operating Instructions Manual

							91VQT2C70
Others
• Electromagnetic wave radiation generated by microprocessors may adversely affect the camera, disturbing the pictures and sound.
• If the camera is adversely affected by electromagnetic equipment and stops functioning  properly, turn the camera off and remove the battery or disconnect AC adaptor (DMW-AC5PP; 
optional). Then reinsert the battery or reconnect AC adaptor and turn the camera on.
Do not use the camera near radio transmitters or high-voltage lines.• If you record near radio transmitters or high-voltage lines, the recorded pictures and sound may be adversely affected.
Always use the supplied cords and cables. If you use optional accessories, use the 
cords and the cables supplied with them.
Do not extend the cords or the cables.
Do not spray the camera with insecticides or volatile chemicals.
• If the camera is sprayed with such chemicals, the body of the camera may be damaged and the surface finish may peel off.
• Do not keep rubber or plastic products in contact with the camera for a long period of time.
Before cleaning the camera, remove the battery or the DC coupler (DMW-DCC4; 
optional), or disconnect the power plug from the outlet. Then wipe the camera with 
a dry soft cloth.
• When the camera is soiled badly, it can be cleaned by wiping the dirt off with a wrung wet cloth,  and then with a dry cloth.
• Do not use solvents such as benzine, thinner, alcohol, kitchen detergents, etc., to clean the  camera, since it may deteriorate the external case or the coating may peel off.
• When using a chemical cloth, be sure to follow the accompanying instructions.
• If the LCD monitor is dirty, blow away dust and foreign matter with a commercial blower brush. 
If it is very dirty, gently rub with a soft cloth or an eyeglass cloth.
• Do not press the LCD monitor with excessive force. Uneven colors may appear on the LCD  monitor and it may malfunction.
• Do not press on the LCD monitor with hard pointed tips, such as ball point pens.
• Do not scratch or press the LCD monitor too hard.
• If the camera is cold when you turn it on, the  picture on the LCD monitor will be slightly darker 
than usual at first. However, the picture will return to normal brightness when the internal 
temperature of the camera increases.
• Do not press the lens with excessive force.
• Do not leave the camera with the lens facing the sun as rays of light from the sun may cause it  to malfunction. Also, be careful when placing the camera outside or near a window.
Cleaning
About the LCD monitor
Extremely high precision technology is em ployed to produce the LCD monitor screen. 
However there may be some dark or bright  spots (red, blue or green) on the screen. 
This is not a malfunction. The LCD monitor screen has more than 99.99% effective 
pixels with a mere 0.01% of the pixels inactive or always lit. The spots will not be 
recorded on pictures on the built-in memory or a card.
About the Lens
DMC-FS7&8&6P-VQT2C70_eng.book  91 ページ  ２００９年２月１７日　火曜日　午前１１時４９分 
						

							VQT2C7092
Others
The battery is a rechargeable lithium ion battery. Its ability to generate power comes 
from the chemical reaction that takes place inside it. This reaction is susceptible to 
the surrounding temperature and humidity. If the temperature is too high or too low, 
the operating time of the battery will become shorter.
Always remove the battery after use.
• Store the removed battery in the battery case (supplied).
If you drop the battery accidentally, check to see if the body 
of the battery and the terminals are damaged.
• Inserting a damaged battery in the camera will damage the camera.
Bring charged spare batteries when going out.• Be aware that the operating time of the battery becomes shorter in low temperature conditions such as at a ski resort.
• When you travel, do not forget to bring the battery charger (supplied) so that you can charge 
the battery in the country that you are traveling in.
Dispose of unusable battery.• The battery has a limited life.
• Do not throw the battery into fire because it may cause an explosion.
• The unusable battery should be discarded in accordance with battery recycling laws. Call the RBRC hotline at 1-800-822-8837 for information.
Do not allow battery terminals to come into contact with metal objects (such as 
necklaces, hairpins etc.).
• This can cause short circuiting or heat generation and you may be badly burned if you touch a battery.
• If you use the battery charger near a radio, the radio reception may be disturbed. 
• Keep the charger 1 m (3.28 feet) or more away from radios.
• The charger may generate whirring sounds when it is being used. This is not a malfunction.
• After use, be sure to disconnect the power suppl y device from the electrical outlet. (A very 
small amount of current is consumed if it is left connected.)
• Keep the terminals of the charger and battery clean.
Do not leave the card where the temperature is high, where electromagnetic waves 
or static electricity are easily generated or exposed to direct sunlight. 
Do not bend or drop the card. 
• The card may be damaged or the recorded content may be damaged or deleted.
• Put the card in the card case or the storage bag after use and when storing or carrying the  card.
• Do not allow dirt, dust or water to get into the terminals on the back of the card and do not touch  the terminals with your fingers.
Notice for when transferring to another party, or disposing of the memory card• “Format” or “delete” using the camera or a PC will only modify the file management information, and it will not erase the data in the memory card completely.
It is recommended to physically destroy the memory card or use the commercially available 
computer data deletion software to completely erase the data in the memory card before 
transferring to another party or disposing.
Management of data in the memory card is the responsibility of the user.
Battery
Charger
Card
DMC-FS7&8&6P-VQT2C70_eng.book  92 ページ  ２００９年２月１７日　火曜日　午前１１時４９分 
						

							93VQT2C70
Others
Personal information is included in the recorded image when the name or birthday is set in 
[BABY1]/[BABY2] in Scene mode.
Disclaimer
• Information including personal information may be altered or vanish due to erroneous 
operation, effect of static electricity, accident, malfunction, repair, or other handlings.
Please note in advance that Panasonic is not liable in any way for any direct or indirect damage 
from the alteration or vanishing of information or personal information.
When requesting a repair, transferring to another party or disposing• Reset the settings to protect the personal information. (P24)
• If there are pictures stored in the built-in memory, copy them into the memory card (P80) before  formatting the built-in memory (P25) as needed.
• Remove the memory card from the camera when requesting a repair.
• Built-in memory and settings may return to factory default when camera is repaired.
• Please contact the dealer where you purchased the camera or your nearest Service Centre if  above operations are not possible due to malfunction.
When transferring to another party, or disposing of the memory card, please refer to 
“Notice for when transferring to another party, or disposing of the memory card” on  
P92.
• Store the battery in a cool and dry place with a relatively stable temperature: [Recommended 
temperature: 15 oC to 25 oC (59 oF to 77 oF), Recommended humidity: 40% to 60%]
• Always remove the battery and the card from the camera.
• If the battery is left inserted in the camera, it will discharge even if the camera is turned off. If  the battery continues to be left in the camera , it will discharge excessively and may become 
unusable even if charged.
• When storing the battery for a long period of time, we recommend charging it once a year. 
Remove the battery from the camera and store it again after it has completely discharged.
• We recommend storing the camera with a desiccant (silica gel) when you keep it in a closet or  a cabinet.
• Recorded data may be damaged or lost if the camera breaks down due to inappropriate  handling. Panasonic will not be liable for any damage suffered due to loss of recorded data.
• When you use a tripod, make sure the tripod is stable when this unit is attached to it.
• You may not be able to remove the card or the battery when using a tripod.
• Make sure that the screw on the tripod is not at an angle when attaching or detaching the  camera. You may damage the screw on the camera if you use excessive force when turning it. 
Also, the camera body and the rating label may be damaged or scratched if the camera is 
attached too tightly to the tripod.
• Read the operating instructions for the tripod carefully.
• Some tripods cannot be attached when the DC coupler (DMW-DCC4; optional) and AC adaptor  (DMW-AC5PP; optional) are connected.
About the personal information
When not using the camera for a long period of time
About the picture data
About tripods
DMC-FS7&8&6P-VQT2C70_eng.book  93 ページ  ２００９年２月１７日　火曜日　午前１１時４９分 
						

							VQT2C7094
Others
Message Display
Confirmation messages or error messages will be displayed on the screen in some cases.
The major messages are described below as examples.
[THIS MEMORY CARD IS LOCKED]
>The Write-Protect switch on the SD Memory Card and the SDHC Memory Card are 
moved to [LOCK]. Move the switch back to unlock it. (P17)
[NO VALID PICTURE TO PLAY]
>Record a picture or insert a card with a recorded picture and then play it.
[THIS PICTURE IS PROTECTED]
>Delete the picture after canceling the protect setting. (P79)
[THIS PICTURE CANNOT BE DELETED]/[SOME PICTURES CANNOT BE DELETED]
• Pictures not based on the DCF standard cannot be deleted.
> If you want to delete some pictures, format the card after saving necessary data on a PC 
etc. (P25)
[NO ADDITIONAL SELECTIONS CAN BE MADE]
• The number of pictures, which can be set at one time when [MULTI] has been selected for 
[DELETE MULTI] (P37), [FAVORITE] (P77), [TITLE EDIT] (P72), [TEXT STAMP] (P73) or 
[RESIZE] (P74) has been exceeded.> Reduce the number of pictures set, and then repeat the operation.
• More than 999 favorites have been set.
[CANNOT BE SET ON THIS PICTURE]
• [TITLE EDIT], [TEXT STAMP] or [PRINT SET] cannot be set for pictures not based on the  DCF standard.
[NOT ENOUGH SPACE ON BUILT-IN MEMORY]/[NOT ENOUGH MEMORY ON THE 
CARD]
• There is no space left on the built-in memory or the card.
– When you copy pictures from the built-in memory to the card (batch copy), the pictures are  copied until the capacity of the card becomes full.
[SOME PICTURES CANNOT BE COPIED]/[C OPY COULD NOT BE COMPLETED] 
• The following pictures cannot be copied.
– When a picture with the same name as the picture to be copied exists in the copy  destination. (Only when copying from a card to the built-in memory.)
– Files not based on the DCF standard.
• Moreover, pictures recorded or edit ed by other equipment may not be copied.
[BUILT-IN MEMORY ERROR
FORMAT BUILT-IN MEMORY?]
• This message will be displayed when you formatted the built-in memory on a PC.
> Format the built-in memory on the camera again. (P25) The data on the built-in memory 
will be deleted.
DMC-FS7&8&6P-VQT2C70_eng.book  94 ページ  ２００９年２月１７日　火曜日　午前１１時４９分 
						

							95VQT2C70
Others
[MEMORY CARD ERROR
FORMAT THIS CARD?]
• This card has a format which is not recognized by the camera.> Format the card again with the camera after saving necessary data on a PC etc. (P25)
[PLEASE TURN CAMERA OFF AND THEN ON AGAIN]/[SYSTEM ERROR]
• This message appears when the camera is not operating properly.
> Turn the camera off and on. If the message persists, contact the dealer or your nearest 
Service Center.
[MEMORY CARD PARAMETER ERROR]
>Use a card compatible with this unit. (P17)
• You can only use an SDHC Memory Card if  using cards with 4 GB or more capacity.
[MEMORY CARD ERROR
PLEASE CHECK THE CARD]
• An error has occurred accessing the card.
> Insert the card again.
> Insert a different card.
[READ ERROR/WRITE ERROR
PLEASE CHECK THE CARD]
• It has failed to read or write data. 
> Remove the card after turning the power [OFF]. Insert the card again, turn the power on, 
and try to read or write the data again. 
• The card may be broken.
> Insert a different card.
[MOTION RECORDING WAS CANCELLED DUE TO THE LIMITATION OF THE 
WRITING SPEED OF THE CARD]
• When you set the recording quality to [ ] or [ ], we recommend using a high-speed 
card with “10MB/s” or greater displayed on the package.
• In the event that it stops even after using a “10MB/s” card or higher, the data writing speed has 
deteriorated so it is recommended to make a backup and then format (P25).
• Depending on the type of SD Memory Card or SDHC Memory Card, motion picture recording  may stop in the middle.
[A FOLDER CANNOT BE CREATED]
• A folder cannot be created because there are no remaining folder numbers that can be used. 
(P83)> Format the card after saving necessary data on a PC etc. (P25) If you execute 
[NO.RESET] in the [SETUP] menu after formatting, the folder number is reset to 100. 
(P24)
[PICTURE IS DISPLAYED FOR 4:3 TV]/[PICTURE IS DISPLAYED FOR 16:9 TV]
• The AV cable (P88) is connected to the camera.
> Press [MENU/SET] if you want to delete this message at once.
> Select [TV ASPECT] in the [SETUP] menu if you want to change the TV aspect. (P25)
• This message also appears when the USB connection cable is connected to the camera only.
In this case, connect the other end of the USB connection cable to a PC or a printer. (P81, 84)
[PRINTER BUSY]/[PLEASE CHECK THE PRINTER]
• The printer cannot print. > Check the printer.
DMC-FS7&8&6P-VQT2C70_eng.book  95 ページ  ２００９年２月１７日　火曜日　午前１１時４９分 
						

							VQT2C7096
Others
Troubleshooting
First, try out the following procedures (P96–102).
• The battery is not inserted correctly. (P14)
• The battery is exhausted.
• Is [AUTO LCD OFF] (P23) of the [ECONOMY] mode active?> Press the shutter button halfway to cancel these modes.
• The battery is exhausted.
• The battery is exhausted.
• If you leave the camera on , the battery will be exhausted.
> Turn the camera off frequently by using the [ECONOMY] mode etc. (P23)
• Is the temperature of the battery excessively high or low? If it is, it will take longer than usual to  charge the battery or charging may remain incomplete.
• Are the terminals of the charger or battery dirty? > Wipe off the dirt using a dry cloth.
[NO BATTERY POWER REMAINS]
• The remaining battery power is low.
> Charge the battery.
[THIS BATTERY CANNOT BE USED]
• The battery cannot be recognized by the camera.
> Use a genuine Panasonic battery. If this message is displayed even when a genuine 
Panasonic battery is used, contact the dealer or your nearest Service Center.
• The battery cannot be recognized as its terminal is dirty. > Remove any dirt etc. from the terminal.
If the problem is not resolved,  it may be improved by selecting [RESET] (P24) on the 
[SETUP] menu when taking pictures .
Battery and power source
The camera cannot be operated even when it is turned on.
The LCD monitor turns off while the camera is turned on.
The camera turns off immediately after it is turned on.
The [CHARGE] lamp flashes.
DMC-FS7&8&6P-VQT2C70_eng.book  96 ページ  ２００９年２月１７日　火曜日　午前１１時４９分 
						

							97VQT2C70
Others
• Is the [REC]/[PLAYBACK] selector switch at the [!] setting? (P27)
• Is there any memory remaining on the built-in memory or the card? > Delete the pictures which are not necessary to increase the available memory. (P36)
• The picture can become whitish if there is dirt e.g. fingerprints on the lens. > If the lens is dirty, turn on the camera, eject the lens barrel (P11) and gently wipe the lens 
surface with a soft dry cloth.
• Was this picture taken with the flash at the close range when the zoom is near [W] (1 k)?
> Zoom in a little, and then take the pictures. (P33)
> Check that the exposure is correctly compensated. (P44)
> Set Auto bracket (P45), [HI-SPEED BURST] (P52), [FLASH BURST] (P52) in Scene mode 
or [BURST] (P64) of the [REC] mode menu to [OFF].
• The focus range varies depending on the Recording mode. > Set to the proper mode for the distance to the subject.
• The subject is beyond the focus range of the camera. (P31)
• There is camera shake (jitter) or the subject is moving slightly. (P32)
> The shutter speed becomes slower when pictures are taken in dark places so hold the 
camera firmly with both hands to take the pictures. (P28)
> When taking pictures at a slow shutter speed, use the self-timer. (P43)
• Is the number of recordable pictures 2 or less?
• Is the ISO sensitivity high or the shutter speed slow? (ISO sensitivity is set to [AUTO] when the camera is shipped. Therefore, when taking pictures 
indoors etc. noise will appear.)
> Decrease the ISO sensitivity. (P61)
> Set [COLOR MODE] to [NATURAL]. (P65)
> Take pictures in bright places.
• Has [HIGH SENS.] or [HI-SPEED BURST] in the Scene mode been set? If so, the resolution of  the recorded picture decreases slightly because of high sensitivity processing, but this is not a 
malfunction.
Recording
The picture cannot be recorded.
The recorded picture is whitish.
The area around where the pictures were taken becomes dark.
The recorded picture is too bright or dark.
2 or 3 pictures are taken at one time.
The subject is not focused properly.
The recorded picture is blurred. The Optical image stabilizer is not effective.
Taking pictures using Auto bracket is not possible.
The recorded picture looks rough. Noise appears on the picture.
DMC-FS7&8&6P-VQT2C70_eng.book  97 ページ  ２００９年２月１７日　火曜日　午前１１時４９分 
						

							VQT2C7098
Others
• If recording under fluorescent light, the brightness or the hue may change slightly when the shutter speed becomes fast. This occurs due to the characteristics of fluorescent light. It is not 
a malfunction.
• Depending on the type of the card, recording may stop in the middle. > When you set the recording quality to [ ] or [ ], we recommend using a high-speed 
card with “10MB/s” or greater displayed on the package.
> In the event that it stops even after using a “10MB/s” card or higher, the data writing speed 
has deteriorated so it is recommended to make a backup and then format (P25).
• Are you using a MultiMediaCard? This unit does not support MultiMediaCards.
• The LCD monitor turns off and the status indicator lights when [AUTO LCD OFF] (P23) is  selected for the [ECONOMY] mode. 
[This does not happen when using the AC  adaptor (DMW-AC5PP; optional).] 
If the remaining battery power is low, it may take longer for the flash to be charged, and the 
time during which the LCD monitor is turned off may become longer.
• This phenomenon appears when you press the shutter button halfway to set the aperture value  and does not affect the recorded pictures.
• This phenomenon also appears when the brightness changes when the camera is zoomed or 
when the camera is moved. This is because of operation of the automatic aperture of the 
camera, and it is not a malfunction.
• The LCD monitor may flicker for a few seconds after turning the camera on indoors under  fluorescent light. This is not a malfunction.
> Adjust the brightness of the screen. (P22)
• [POWER LCD] or [HIGH ANGLE] is activated. (P23)
The brightness or the hue of the recorded picture is different from the actual 
scene.
A reddish vertical line (smear) appears on the LCD monitor during 
picture-taking.
• This is a characteristic of CCDs, and it appears when the subject has a 
bright part. Some unevenness may occur in the surrounding areas, but 
this is not a malfunction.
It is recorded in motion pictures but is not recorded on still pictures.
• It is recommended that you take pictures while taking care not to expose  the screen to sunlight or any other source of strong light.
Motion picture recording stops in the middle.
LCD monitor
The LCD monitor turns off although the camera is turned on.
The LCD monitor becomes darker or brighter for a moment.
The LCD monitor flickers indoors.
The LCD monitor is too bright or dark.
DMC-FS7&8&6P-VQT2C70_eng.book  98 ページ  ２００９年２月１７日　火曜日　午前１１時４９分 
						

							99VQT2C70
Others
• This is not a malfunction.These pixels do not affect the recorded pictures.
• In dark places, noise may appear to maintain the brightness of the LCD monitor. This does not  affect the pictures you are recording.
• If the LCD monitor is pressed with a finger and pressure is applied, distortion (uneven colors)  will appear on the screen, but this is not a malfunction.
• Is the flash setting set to [ Œ]?
> Change the flash setting. (P39)
• Flash mode is not available when Auto bracket (P45) or [BURST] (P64) in [REC] mode menu  has been set.
• The flash is activated twice when red-eye reduction (P39) has been set.
• Has [FLASH BURST] (P52) in Scene mode been set?
• [ROTATE DISP.] (P76) is set to [ON].
• Is the [REC]/[PLAYBACK] selector switch set to [ (]? (P34)
• Is there a picture on the built-in memory or the card? > The pictures on the built-in memory appear when a card is not inserted. The picture data on 
the card appears when a card is inserted.
• Is this a picture whose file name has been changed in the PC? If it is, it cannot be played back  by this unit.
• Has [CATEGORY PLAY] or [FAVOR ITE PLAY] been set for playback?
> Change to [NORMAL PLAY]. (P34)
Black, red, blue and green dots appear on the LCD monitor.
Noise appears on the LCD monitor.
Distortion appears in the LCD monitor.
Flash
The flash is not activated.
Flash is activated several times.
Playback
The picture being played back is rotated and displayed in an unexpected 
direction.
The picture is not played back.
The recorded pictures are not displayed.
DMC-FS7&8&6P-VQT2C70_eng.book  99 ページ  ２００９年２月１７日　火曜日　午前１１時４９分 
						

							VQT2C70100
Others
• Is this a non-standard picture, a picture which has been edited using a PC or a picture which was taken by another maker of digital camera?
• Did you remove the battery immediately after picture-taking or did you take the picture using a 
battery with a low remaining charge?> Format the data to delete the pictures mentioned above. (P25)
(Other pictures will be deleted as well and it will not be possible to restore them. 
Therefore, check well before formatting.)
• Is the clock in the camera set properly? (P18)
• When pictures edited using a PC or pictures taken by other equipment are searched, they may 
be displayed on dates differing from the actual dates on which the pictures were taken.
• When the flash is set to red-eye reduction ([ ], [ ], [ ]) and if you take a picture of  subject with red color surrounded by a skin tone color, that red part may be corrected to black 
by the digital red-eye reduction function.
> It is recommended to take picture with Flash mode set to [
‡], [‰], or [Œ].
• Is it a picture that has been recorded with other equipment? In such cases, these pictures may  be displayed with a deteriorated picture quality.
• This unit automatically adjusts the aperture during motion picture recording. At such times, the  sound may break up. This is not a malfunction.
• Is the camera connected to the TV correctly? > Set the TV input to external input mode.
• Depending on the TV model, the pictures may be extra horizontally or vertically or they may be  displayed with their edges cut off.
The folder number and the file number are displayed as [—] and the screen turns 
black.
With a calendar search, pictures are displayed on dates differing from the actual 
dates on which the pictures were taken.
White round spots like soap bubbles appear on the recorded picture.
• If you take a picture with the flash in a dark place or indoors, white 
round spots may appear on the picture caused by the flash reflecting of 
particles of dust in the air. This is not a malfunction. 
A characteristic of this is that the number of round spots and their 
position differ in every picture.
Red part of the recorded image has changed color to black.
[THUMBNAIL IS DISPLAYED] appears on the screen.
The sound of the recorded motion pictures sometimes breaks up.
TV, PC and printer
The picture does not appear on the television.
The display areas on the TV screen and the camera’s LCD monitor are different.
DMC-FS7&8&6P-VQT2C70_eng.book  100 ページ  ２００９年２月１７日　火曜日　午前１１時４９分