Panasonic Dmc Fh22 Operating Instructions Manual

							Advanced (Playback)
- 111 -
„„To print the date ([DATE] setting)
•
 When y ou go to a photo printing store for digital printing, be sure to order the printing of 
the date additionally if required.
•
 
Depending on the photo pr
 inting store or the printer, the date may not be printed even if 
you set to print the date. For further information, ask at your photo printing store or refer 
to the operating instructions for the printer.
•
 
The date cannot be pr
 inted on pictures stamped with text.
 Note
•
 
The n
 umber of prints can be set from 0 to 999.
•
 
With a pr
 inter supporting PictBridge, the date print settings of the printer may take 
precedence so check if this is the case.
•
 
It ma
 y not be possible to use the print settings with other equipment. In this case, cancel 
all the settings, and reset the settings.
•
 
If the file is not based on the DCF standard, the pr
 int setting cannot be set. 
						

							Advanced (Playback)
- 112 -
[PROTECT]
You can set protection for pictures you do not want to be deleted by mistake.
1 Select [PROTECT] on the [PLAYBACK] Mode menu (P22).
2 Touch [SINGLE] or [MULTI].
[SINGLE]
[MULTI]3 Select the picture(s) to be pr otected.
[SINGLE] setting
Touch [w]/[q] to select the picture, and touch [SET].
•
 
Setting is canceled b
 y selecting protected picture and 
touching [CANCEL].
[MULTI] setting
Touch the image to select the picture.
•
 
Repeat touching to select other pictures
 .
•
 
Setting is canceled b
 y touching the same picture again.
4 Touch [EXIT].• Touch [EXIT] to close the menu.
„„ Canceling all the [PROTECT] settings
1
 
T

ouch [CANCEL] in step 
2.
2
 T
ouch [YES].
 Note
•
 
The protect setting ma
 y not be effective on other equipment.
•
 
Ev
 en if you protect pictures in the built-in memory or a card, they will be deleted if the 
built-in memory or the card is formatted.
•
 
Ev
 en if you do not protect pictures on a card, they cannot be deleted when the card’s 
Write-Protect switch is set to [LOCK]. 
						

							Advanced (Playback)
- 113 -
[COPY] Copying pictures from the built-in memory to a card
You can copy the data of the pictures you have taken from the built-in memory to a card 
or from a card to the built-in memory.
1 Select [COPY] on the [PLAYBACK] Mode menu. (P22)
2 Touch the copy destination to select.
N: All the picture data in the b uilt-in memory are 
copied onto the card at one time. " step 4.
M:
 One picture at a time is copied from the card to 
the b

uilt-in memory. " step 3.
3 Touch [w]/[q] to select the picture, and touch [SET].
4 Touch [YES].• If you touch [CANCEL] while copying pictures from the built-in memory to the card, the copying will stop halfway.
•
 
Do not tur
 n the camera off at any point during the copying 
process.
5 Touch [CANCEL] to return to the menu screen.• Touch [EXIT] to close the menu.
•  If y ou copy from the built-in memory to a card, all the pictures are copied and then 
the screen automatically returns to the playback screen.
 Note
•
 
If y
 ou copy picture data from the built-in memory to a card which does not have 
sufficient free space, the picture data will only be copied halfway. We recommend using 
a card which has more free space than the built-in memory (about 40 MB).
•
 
If a picture e
 xists with the same name (folder number/file number) as the picture to be 
copied in the copy destination when [N] is selected, a new folder is created and the 
picture is copied. If a picture exists with the same name (folder number/file number) as 
the picture to be copied in the copy destination when [M] is selected, that picture is 
not copied. (P135)
•
 
It ma
 y take time to copy the picture data.
•
 
Only pictures recorded with a P
 anasonic digital camera (LUMIX) will be copied.  
(Even if the pictures were recorded with a Panasonic digital camera, you may not be 
able to copy them if they were edited with a PC.)
•
 
Pr
 int settings or Protect settings on the original picture data will not be copied. Set the 
settings again after copying is finished. 
						

							Connecting to other equipment
- 114 -
You can acquire recorded pictures to a PC by connecting the camera and the PC.
• If the pictures are recorded on a card y ou can also use it by means of inserting directly 
to an SD Memory Card slot of your PC. For details, refer to the operating instructions of 
the PC.
•
 
If y
 our computer does not support SDXC Memory Cards, a message will be displayed 
requesting you to format the card. (Do not format the card. This will erase recorded 
pictures.)  
If the card is not recognized, refer to the following support website. 
http://panasonic.net/avc/sdcard/information/SDXC.html
•
 
Y
 ou can easily print out or e-mail the pictures you have imported. Use of the 
“PHOTOfunSTUDIO” bundled software on the CD-ROM (supplied) is a convenient way 
of doing this.
•
 
Read the separ
 ate operating instructions for the supplied software for more information 
about the software in the CD-ROM (supplied) and how to install it.
Preparations:
Turn on the camera and the PC.
Remove the card before using the pictures in the built-in memory.
AV OUT
DIGITAL 
A	
USB connection cable (supplied)
•  Chec k the directions of the connectors, and plug them straight in or unplug them 
straight out. (Otherwise the connectors may be bent out of shape which will cause a 
malfunction.)
B	 Align the marks, and insert.
•
 
Use a batter
 y with sufficient battery power or the AC adaptor (optional) and DC coupler 
(optional). If the remaining battery power becomes low while the camera and the PC are 
communicating, the alarm beeps. 
Refer to “Disconnecting the USB connection cable safely”  (P115) before disconnecting the 
USB connection cable. Otherwise, data may be destroyed.
Connecting to a PC 
						

							Connecting to other equipment
- 115 -
1 Connect the camera to a PC via the USB connection cable A 
(supplied).
• Do not use an y other USB connection cables except the supplied one.  
Use of cables other than the supplied USB connection cable may cause a 
malfunction.
USB MODE
PLEASE SELECT
THE USB MODE
PictBrid\fe(PTP)
PC2 Touch [PC].• If [USB MODE]  (P30) is set to [PC] in the [SETUP] menu in 
advance, the camera will be automatically connected to the 
PC without displaying the [USB MODE] selection screen. 
Since there is no need to set this each time you connect to 
the PC, it is convenient.
•
 
When the camer
 a has been connected to the PC with 
[USB MODE] set to [PictBridge(PTP)], a message may appear on the PC’s 
screen. Select [Cancel] to close the screen, and disconnect the camera from the 
PC. Then set [USB MODE] to [PC] again.
3 Double-click on [Removable Disk] in [My Computer].• When using a Macintosh, the dr ive is displayed on the desktop. (“LUMIX”, 
“NO_NAME” or “Untitled” is displayed.)
4 Double-click [DCIM] folder.
5 Using a dra g-and-drop operation, move the pictures you want to 
acquire or the folder storing those pictures to any different folder on 
the PC.
„„ Disconnecting the USB connection cable safely
•
 Proceed with the hardw are removal using “Safely Remove Hardware” on the task tray 
of the PC. If the icon is not displayed, check that [ACCESS] is not displayed on the LCD 
monitor of the digital camera before removing the hardware.
 Note
•
 
This unit cannot stand upr
 ight when the AC adaptor is connected. When operating it on 
a flat surface, we recommend placing it on a soft cloth.
•
 
T

urn the camera off before connecting or disconnecting the AC adaptor (optional).
•
 
Bef
 ore inserting or removing a card, turn the camera off and disconnect the USB 
connection cable. Otherwise, data may be destroyed. 
						

							Connecting to other equipment
- 116 -
„„Viewing the contents of the built-in memory or card using the PC (folder 
composition)
1	Folder number
2	 File number
3	 JPG:
 Pictures MO

V:
 Motion pictures
MISC:

   
DPOF pr
 int  
Favorite
D C I M
M I S C 100_PANA
101_PANA
999_PANA
P1000001.JPG
P1000002.JPG
P1000999.JPG
100_PANA
1
2 3• Built-in 
memor y
•
 
Card
A ne

w folder is created when pictures are taken in the following situations.
•
 
When a card containing a f
 older with the same folder number has been inserted (Such 
as when pictures were taken using another maker of camera)
•
 
When there is a picture with file n
 umber 999 inside the folder
„„ Connection in the PTP Mode (Windows
® XP, Windows Vista®, Windows® 7 and 
Mac OS X only)
Set [USB MODE] to [PictBridge(PTP)].
Data can now be read only from the card into the PC.
•
 
When there are 1000 or more pictures on a card, the pictures ma

y not be imported in 
the PTP Mode. 
						

							Connecting to other equipment
- 117 -
If you connect the camera to a printer supporting PictBridge, you can select the pictures 
to be printed and instruct that printing be started on the camera’s LCD Monitor.
• 
If the pictures are recorded on a card y
 ou can also use it by means of inserting directly 
to an SD Memory Card slot of your printer. For details, refer to the operating instructions 
of the printer.
Preparations:
Turn on the camera and the printer.
Remove the card before printing the pictures in the built-in memory.
Perform the print quality and other settings at the printer before printing the pictures.
AV OUT
DIGITAL
A	 USB connection cable (supplied)
•  Chec k the directions of the connectors, and plug them straight in or unplug them straight 
out. (Otherwise the connectors may be bent out of shape which may cause malfunction.)
B	 Align the marks, and insert.
•
 
Use a batter
 y with a sufficient battery power or the AC adaptor (optional) and DC 
coupler (optional). If the remaining battery power becomes low while the camera and the 
printer are connected, the status indicator blinks and the alarm beeps. If this happens 
during printing, stop printing at once. If not printing, disconnect the USB connection 
cable.
1 Connect the camera to a printer via the USB connection cab le A 
(supplied).
• When the camer a is connected to the printer, the cable disconnect prohibit icon 
[1] appears. Do not disconnect the USB cable while [1] is displayed.
USB MODE
PLEASE SELECT
THE USB MODE
PictBrid\fe(PTP)
PC2 Touch [PictBridge(PTP)].
Printing the Pictures
[PLAYBACK] Mode: 5 
						

							Connecting to other equipment
- 118 -
 Note
•
 
This unit cannot stand upr
 ight when the AC adaptor is connected. When operating it on 
a flat surface, we recommend placing it on a soft cloth.
•
 
Do not use an
 y other USB connection cables except the supplied one.  
Use of cables other than the supplied USB connection cable may cause malfunction.
•
 
T

urn the camera off before connecting or disconnecting the AC adaptor (optional).
•
 
Bef
 ore inserting or removing a card, turn the camera off, and disconnect the USB 
connection cable.
•
 
Y

ou cannot switch between the built-in memory and the card while the camera is 
connected to the printer. Disconnect the USB connection cable, insert (or remove) the 
card and then connect the USB connection cable to the printer again.
Selecting a single picture and printing it
PictBridge 100-0001 1/19 
14 M
MULTI PRINTPRINT
1 Touch [w]/[q] to select the picture, and touch  [PRINT].
PRINT START
PRINT WITH DATE
NUM.OF PRINTS
CANCEL
SIN\fLE SELECTOFF1
1/22 Touch [PRINT START].• Refer to “Print Settings” 
(P120) for the items which can be set 
before starting to print the pictures.
•
 
Press shutter b
 utton halfway to cancel printing halfway.
•
 
Disconnect the USB connection cab
 le after printing. 
						

							Connecting to other equipment
- 119 -
Selecting multiple pictures and printing them
1 Touch [MULTI PRINT].
SELECT ALLMULTI SELECT
PRINT SET (
DPOF )CANCEL
Pi\ftBri\bge1/22 Touch an item to select.
Item
Description of settings
[MULTI SELECT] Multiple pictures are printed at one time.
•
 
Touch the pictures and [
 2] appears on the pictures to be 
printed. (When the selected picture is touched again, the setting 
is canceled.)
•
 
After the pictures ha
 ve been selected, touch [SET].
[SELECT ALL] Prints all the stored pictures.
[PRINT SET (DPOF)]Prints the pictures set in [PRINT SET] only. (P110)
[FAVORITE]
Prints the pictures set as favorites only. (P109)
¼Only when [FAVORITE] is at [ON] and when there are pictures set as favorites. (P109)
PRINT START
PRINT WITH DATE
NUM.OF PRINTS
CANCEL
MULTI SELECTOFF\f
\f/23 Touch [PRINT START].• Refer to “Print Settings” 
(P120) for the items which can be set 
before starting to print the pictures.
•
 
Press shutter b
 utton halfway to cancel printing halfway.
•
 
Disconnect the USB connection cab
 le after printing. 
						

							Connecting to other equipment
- 120 -
Print Settings
PRINT STARTPRINT WITH DATE
NUM.OF PRINTS
1/\f
CANCEL
MULTI SELECT
OFF1OFFON
Select and set the items both on the screen in step 2 
of the “Selecting a single picture and printing it” and in 
step 
3 of the “Selecting multiple pictures and printing 
them” procedures.
•
 When y

ou want to print pictures in a paper size or 
a layout which is not supported by the camera, set 
[PAPER SIZE] or [PAGE LAYOUT] to [h] and then set the paper size or the layout on 
the printer. (For details, refer to the operating instructions of the printer.)
•
 When [PRINT SET (DPOF)] has been selected, the [PRINT 

WITH DATE] and 
[NUM. OF PRINTS] items are not displayed.
[PRINT WITH DATE]
Item Description of settings
[OFF] Date is not printed.
[ON] Date is printed.
•
 If the pr

inter does not support date printing, the date cannot be printed on the picture.
•
 Since the pr

inter’s settings may take precedence over the Print With Date setting, check 
the printer’s Print With Date setting as well.
•
 When pr

inting images with a Text Stamp, please remember to set Print With Date to 
[OFF] or the date will print on top.
 Note
When asking the photo shop to print the pictures
•
 By 

stamping the date using [TEXT STAMP]  (P103) or setting date printing in [PRINT SET] 
(P110) before going to a photo shop, the dates can be printed at the photo shop.
[NUM. OF PRINTS]
You can set the number of prints up to 999.