Panasonic Digital Video Cassette Recorder Ajd850a Operating Instructions

Ð 41 Ð
Audio split editing
The video edit points and audio edit points can be entered separately, and they can be offset
from each other and edited.
Audio edit points can be entered, deleted and revised only when the inse\
rt editing mode has
been selected. After the edit points have been entered, follow the same operating proce\
dure
as that for insert editing.
nEntering the edit points
Video IN point: Press the SET button while holding down the IN button.
Video OUT point: Press the SET button while...

Ð 42 Ð
Audio split editing
nDisplaying the audio split edit points
The edit points are displayed on the front panel as shown below. (The figure shows an audio
IN point.)
Operations
Video IN point:Press the IN button.
Video OUT point:Press the OUT button.
Audio IN point:Press the A IN button.
Audio OUT point:Press the A OUT button.
AIN 00:00:04:07
IN, OUT, AIN (audio IN point), AOUT (audio OUT point)

If the editing mode is switched to assemble editing after audio edit points have been entered,
these...

Ð 43 Ð
MIC
AMPANALOGUE
AUDIO
IN*
* Connect to the channel whose 
sound is to be recorded.VIDEO
OUT
AJ-D850ATV monitor Microphone
1Select INT_VO as the setup menu No. 322 (AUD MEM MODE) setting.
2Select the same setting for the channel (CH1 or CH2) on which the sound is to be
recorded and for the setup menu No. 323 (AUD MEM CH) channel.
3Insert the cassette tape for which the voice-over editing is to be performed.
4Press the insert button for the channel (CH1 or CH2) on which the sound is to be
recorded...

Ð 44 Ð
Voice-over facility (internal)
Operating procedure 2
1Select INT_VO as the setup menu No. 322 (AUD MEM MODE) setting.
2Select the same setting for the channel (CH1 or CH2) on which the soun\
d is to be 
recorded and for the setup menu No. 323 (AUD MEM CH) channel.
3Insert the cassette tape for which the voice-over editing is to be perfo\
rmed.
4Press the insert button for the channel (CH1 or CH2) on which the soun\
d is to be 
recorded and ensure that its lamp lights.
5Enter the IN and OUT points...

Ð 45 Ð
MIC
AMP
ANALOGUE
AUDIO IN*
VIDEO
OUT
RECORDERAJ-D850A
AG-A850 REMOTE
IN/OUT
CONTROLLER
Ref.
Microphone
TV monitor* Connect to the channel (CH1 or CH2) 
on which the sound is to be recorded.
1Select INT_VO as the setup menu No. 322 (AUD MEM MODE) setting.
2Select the same setting for the channel (CH1 or CH2) on which the sound is to be
recorded and for the setup menu No. 323 (AUD MEM CH) channel.
3Insert the cassette tape for which the voice-over editing is to be performed into the
VTR.
4Set the...

Ð 46 Ð
CH1
Fig. 1
IN OUT
CH2
CH1
Fig. 2
IN OUT
CH2
Event 1
Event 2
Up to 20 sec.
Cross fading by operating the mixer
CH1 insert start
Audio cross channel editing (internal)
Example: To record cross-faded audio signals onto CH2
n Connections
1Select INT_X as the setup menu No. 322 (AUD MEM MODE) setting.
2Select CH2 as the setup menu No. 323 (AUD MEM CH) setting.
3Select the audio CH1 and CH2 in the insert editing.

Select the video as well if the video signals are also going to be edited.
Ref
REMOTE...

Ð 47 Ð
4Enter the edit points of the first event on the player Õs tape.
5Enter the edit points of the first event on the recorder Õs tape.
6Operate the mixer in such a way that the player Õs audio output signals are output from
the mixerÕs CH1 OUT and CH2 OUT connectors. (The same audio signals will be
delivered through CH1 and CH2 of the mixer.)
7Press the AUTO EDIT button. The first event is now recorded on the recorderÕs tape.
(See Fig. 1.)
The last 20 seconds (which is the capacity of the memory) of...

Ð 48 Ð
V blanking data recording/playback
nAdditional line recording/playback function
¥ Select the mode for recording signals in additional lines using setup menu item No. 800
(ADD LINE).
Off:No signals are recorded in additional lines.
YC422:The input signals are recorded in 1 line in the 422 mode.
YC411:The input signals are recorded in 1 line in the 411 mode.
Y1_B/W:The input signals are recorded in 1 line in their original form as the luminance
signal.
Y1_PBF:The input signals are separated into the...

Ð 49 Ð
Video output (encoder output) signal adjustments
After this system has been connected, the video output signal (ENCODER OUT) must be
adjusted if AB roll editing (editing using two source machines) using an editor, for instance, is
to be error-free and accurate. (This adjustment must be repeated when one of the
connecting cables has been replaced and whenever the connections are changed.)
The adjustment procedure using this unit is outlined below.
1Check the connections. (See page 22.)
2Set the...

Ð 50 Ð
Setup (default settings)
The unitÕs major settings are performed by making selections on menus.
The setting menus appear on the TV monitor when the TV monitor and VIDEO OUT 3
connector in the unitÕs connector area are hooked up.
Changing the settings
1Press the MENU button.
The setup menu appears on the TV monitor and setup menu No. appears on the
counter display. (If the setup has already been performed, the screen showing the
changes made last will appear.)
2Rotate the search dial and select the...