Home
>
Panasonic
>
Camcorder
>
Panasonic Digital Video Camera Recorder AG-DVX100P Operating Instructions
Panasonic Digital Video Camera Recorder AG-DVX100P Operating Instructions
Have a look at the manual Panasonic Digital Video Camera Recorder AG-DVX100P Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
61 Troubleshooting (Q&A) Power supply-related problems Q1: No power. A1: Has the battery or AC adapter been connected correctly? Check the connections. (See page 22) Q2: The power goes off on its own. A2: The power will automatically go off if shooting is temporarily stopped for more than 5 minutes in order to prevent the battery from running down and keep the tape from wearing. Check the setting selected for the TAPE PROTECT item on the setting menu OTHER FUNCTIONS screen. (See page 46) Q3: The power is turned on but it goes off immediately. A3-1: Has the battery run down? If the remaining battery charge display flashes or the display has appeared, it means that the battery has run down. Recharge the battery or insert an adequately charged battery. (See page 21) A3-2: Has condensation formed? When the camera recorder has been carried into a warm room from a cold place, condensation may form inside. If this happens, the power is automatically turned off, and ejecting the cassette is the only operation which can be performed. Wait until the condensation has dried up. (See page 60) Battery-related problems Q1: The battery runs down quickly. A1-1:Has the battery been adequately charged? Charge it until the CHARGE lamp of the AC adapter has gone off. (See page 21) A1-2: Is the camera recorder being used in cold place? The battery is easily affected by the ambient temperature. Its operating time is reduced in cold locations. A1-3:Has the battery reached the end of its service life? The service life of the battery differs depending on how it is used. If it works only for a short time even after it has adequately charged, it means that the battery has reached the end of its service life. Q2: The battery cannot be charged. A2: Is the DC cable connected to the AC adapter? The battery cannot be charged if this cable is connected. Problems during normal video recording Q1: Recording is not possible even though the cassette tape has been inserted properly. A1-1:Has the accidental erasure prevention knob on the cassette tape been set to “SAVE?” If it has, recording cannot be performed. (See page 23) A1-2:Has the cassette tape reached the end? Replace it with a new one. A1-3: Is the POWER switch at the ON position? A1-4: Is the VCR lamp lighted? Shooting is not possible in the VCR mode. A1-5: Is the cassette holder open? If the cassette holder is open, it is not possible to perform any VCR operations. A1-6: Has condensation formed? If condensation has formed, ejecting the cassette tape is the only operation which can be performed. Wait until the condensation dries up. (See page 60) A1-7: If AUTO OFF/T REEL LOCK appears on the display, the tape may have snapped. Check the tape.
62 Troubleshooting (Q&A) Problems during various kinds of video recording Q1: No automatic focusing A1-1:Has the manual focus mode been set? The focus is adjusted automatically in the auto focus mode. (See page 12) A1-2: Is a scene which is hard to bring into focus in the auto focus mode being shot? Some scenes are hard to bring into focus using auto focus. In cases like this, use the manual focus mode instead for focusing. Scenes hard to bring into focus OShooting both distant and close-up subjects OShooting subjects through dirty window panes OShooting subjects in dark locations OShooting while objects that glitter or dazzle are around the subject OShooting fast-moving subjects OShooting subjects with minimal contrast Editing-related problems Q1: No audio dubbing. A1-1:Has the accidental erasure prevention knob on the cassette tape been set to “SAVE?” If it has, recording cannot be performed. (See page 23) A1-2:Has an attempt been made to edit parts shot in the LP mode? Audio dubbing cannot be performed as the track width on the tape is narrower than the head width in the LP mode. Display-related problems Q1: Something is wrong with the time code display. A1: When the reverse slow playback mode is set, the count shown on the time code display becomes inconsistent; however, this is normal and not indicative of malfunctioning. Q2: The remaining tape display does not match the actual amount of tape remaining. A2-1:The remaining tape is not displayed accurately with continuous shooting sessions lasting less than 30 seconds. A2-2: A display which is two to three minutes less than the actual tape remaining time sometimes appears. Playback-related problems (video) Q1: No playback, even when the play button is pressed. A1: Has the CAMERA/VCR button been pressed and has the VCR lamp lighted? If the VCR lamp is not lighted, playback- related operations cannot be performed. (See page 11) Q2: Mosaic-type noise is generated during cue and review. A2: This is a phenomenon inherent to digital video. It is not indicative of malfunctioning. Q3: No playback images are seen even though the camera recorder is connected with the TV set correctly. A3: Is the TV set’s input selector at “video input?” Read through the operating instructions of the TV set, and select the video input connector to which the camera recorder has been connected. Q4: The playback images are not displayed clearly. A4: Are the camera recorder’s heads dirty? If they are dirty, the playback images will not be displayed clearly.
63 Troubleshooting (Q&A) Other types of problems Q1: The cassette tape cannot be ejected. A1: Is power being supplied? Has the AC adapter been plugged in or the battery inserted properly? When the power is supplied, the cassette can be ejected without setting the POWER switch to ON. Q2: Ejecting the cassette tape is the only operation which can be performed. A2-1: Has any condensation formed? If condensation forms, ejecting the cassette tape is the only operation which can be performed. Wait until the condensation dries up. (See page 60) A2-2:When the cassette holder is closed immediately after opening (by sliding the EJECT switch), operations other than eject may not be possible. If this does happen, slide the EJECT switch to open the cassette holder once again, then close the holder after ensuring that the cassette mechanism has completed the eject operation. Q3: The remote control unit does not work. A3-1:Has the battery in the remote control unit run down? If the remote control unit fails to operate even when it is operated near the remote control sensor of the camera recorder, it means that the button battery has run down. Replace it with a new one. (See page 20) A3-2: Do the remote control settings match properly? If the [REMOTE] settings of the remote control unit and camera recorder do not match, the remote control unit will not work even when it is operated. (See page 20) Q4: A rattling sound is heard when the camera recorder is tilted toward the front or back. A4: When the VCR mode is established or the power switch is at OFF, a rattling sound may be heard from the camera unit due to its structure. This is not indicative of malfunctioning. Playback-related problems (audio) Q1: No playback sound is heard from the camera recorder’s speaker. A1: Has the camera recorder’s volume level been set too low? In the VCR mode, press the AUDIO MON/VAR button “+” to increase the volume. (See page 15) Q2: More than one recorded stream of sound is heard. A2: Has MIX been selected as the setting for the 12-bit AUDIO item on the setting menu PLAYBACK FUNCTIONS screen? (See page 42) If audio dubbing editing is performed on a tape recorded with 12-bit selected as the setting for the AUDIO REC item on the setting menu RECORDING SETUP screen, the sound heard during the recording and the sound recorded later will be heard together. It is also possible to listen to each stream of sound separately. (See page 43) Q3: When audio dubbing is performed, the original sound is erased. A3: When audio dubbing is performed for a part which was shot with 16-bit selected as the setting for the AUDIO REC item on the setting menu RECORDING SETUP screen, the original sound will be erased. Use the 12-bit setting during shooting. (See page 43)
64 Maintenance Viewfinder maintenance When dust has collected inside the viewfinder, take off the eye cup holder, and remove the dust. OThe inside of the eye cup holder has a special coating: for this reason, it must not be wiped under any circumstances. When dust has collected, use an air blower or similar device to blow off the dust. OPoint the viewfinder slightly upward, then remove the eye cup holder by turning it counterclockwise. OTo attach the eye cup holder, turn it clockwise with the index mark on the eye cup holder face up. Do not use benzine or paint thinners to clean the camera recorder. OUse of benzine or paint thinners may cause the camera recorder body to become deformed or the surface coating to peel off. OWhen cleaning or otherwise maintaining the camera recorder, either remove its battery or disconnect its AC cable from the power outlet. OUse a soft, clean cloth to wipe the camera recorder. To remove stubborn stains, dilute some kitchen detergent, dip a cloth into the solution and use it to wipe off the dirt, and then remove any remaining moisture with a dry cloth. Index mark Eye cup holder
65 Specifications indicates safety information. Supply voltage:DC 7.2/7.9 V Power consumption: 6.8 W (when viewfinder is used) 7.8 W (when LCD monitor is used) 9.2 W (max.) Ambient operating temperature 32°F to +104°F (0°C to +40°C) Ambient operating humidity 10% to 85% (no condensation) Weight 3.652 lb (1.66 kg) (excluding battery and accessories) Dimensions (WaHaD) 5 1/2a6 5/16a14 3/8inches (139a160a364 mm) Recording format Digital video SD format Tape format Mini DV Recorded video signals 525i (NTSC) In the progressive mode, the signals are converted into the 525i system and recorded. Shooting mode 60i (525i) Progressive mode (30P, 24P or 24P advance) Recorded audio signals PCM digital recording 16 bits: 48 kHz/2 channels 12 bits: 32 kHz/4 channels Recording tracks Digital video, audio signals: helical track Time code: helical track (sub-code area) Tape speed SP mode: 18.812 mm/sec. LP mode: 12.555 mm/sec. Recording time (when AY-DVM60 is used) SP mode: 60 minutes LP mode: 90 minutes Tape used 6.35 mm wide metal tape FF/REW time Approx. 85 sec. (when AY-DVM60 is used) [GENERAL]Pick-up device Interline transfer 1/3-inch CCD image senser (a3) Number of pixels Total number of pixels: 410,000, Number of effective pixels: 380,000 (pixel offset system) Lens Leica DICOMAR optical image stabilizer lens, motorized/manual mode switching, 10azoom F1.6 (f = 4.5 to 45 mm) (35 mm equivalent: 32.5 to 325 mm) Optical system Prism system ND filters 1/8, 1/64 Gain 0, +3, +6, +9, +12, +18 dB (60i mode only) Shutter speeds Preset 60i mode: 1/60 (OFF), 1/100, 1/120, 1/250, 1/500, 1/1000, 1/2000 sec. 30P mode: 1/30, 1/50 (OFF), 1/60, 1/120, 1/250, 1/500, 1/1000 sec. 24P, 24P (ADV) mode: 1/24, 1/50 (OFF), 1/60, 1/120, 1/250, 1/500, 1/1000 sec. Synchro scan 60i mode: 1/60.3 to 1/250.0 sec. 30P mode: 1/30.1 to 1/250.0 sec. 24P, 24P (ADV) mode: 1/24.1 to 1/250.0 sec. Minimum subject illuminance 3 lux (F1.6, 18 dB gain, 50 IRE video output) Lens hood Large-sized lens hood with wide angle of view Filter diameter 72 mm LCD monitor 3.5-inch LCD color monitor, 200,000 pixels Viewfinder 0.44-inch LCD color viewfinder, 180,000 pixels Internal microphone Stereo microphone Internal speaker 20 mm diameter
66 Specifications [VIDEO] Sampling frequency Y: 13.5 MHz, PB/PR: 3.375 MHz Quantizing 8 bits Video compression system DCT + variable length code Error correction Reed-Solomon product code [AUDIO] Sampling frequency 48 kHz/32 kHz Quantizing 16 bits/12 bits Frequency response 20 Hz to 20 kHz Wow & flutter Below measurable limits [CONNECTORS] VIDEO IN/OUT (input/output automatically switched) Pin jack, analog composite input/output, 1.0 V [p-p], 75 Ω S-VIDEO IN/OUT (input/output automatically switched) S-connector, Y/C separate signal input/output, Y: 1.0 V [p-p], C: 0.286 V [p-p], 75 Ω AUDIO IN/OUT (input/output automatically switched) Pin jacks a2 (CH1, CH2) Input: 316 mV, high impedance Output: 316 mV, 600 Ω DV 4-pin, digital input/output, IEEE 1394 standard complied with INPUT 1, INPUT 2 XLR (3 pins) a2 (CH1, CH2) LINE/MIC switching, high impedance LINE : 0 dBu MIC :–50 dBu/–60 dBu (menu selection) DC INPUT 7.9 V PHONES Stereo (3.5 mm diameter), 77 mV, 32 Ω CAM REMOTE Mini jack (2.5 mm diameter) [OPTIONAL ACCESSORIES] Wide conversion lens AG-LW7208G 16:9 conversion lens AG-LA7200G XLR microphone AG-MC100G Hard carrying case AG-HT100G Soft carrying case AG-SC100G Battery CGR-D08 (800 mAh) CGR-D16 (1600 mAh: product equivalent to battery supplied) CGP-D28 (2800 mAh) AC adapter kit AG-B15 (product equivalent to AC cable, DC cable and AC adapter supplied) Cleaning tape AY-DVMCL indicates safety information. Power Source: 110/120/220/240 V AC, 50/60 Hz Power Consumption: 18 W Weight 0.35 Ib (0.16 kg) Dimensions (WaHaD) 2 13/16a1 13/16a4 5/8inches (70a44.5a116 mm) [AC ADAPTER] Weight and dimensions shown are approximate. Specifications are subject to change without notice.
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000 EASTERN ZONE: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621 Southeast Region: 1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835 Central Region: 1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200 WESTERN ZONE: 3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500 Government Marketing Department: 52 West Gude Drive, Rockville, MD 20850 (301) 738-3840 Broadcast PARTS INFORMATION & ORDERING: 9:00 a.m. – 5:00 p.m. (EST) (800) 334-4881/24 Hr. Fax (800) 334-4880 Emergency after hour parts orders (800) 334-4881 TECHNICAL SUPPORT: Emergency 24 Hour Service (800) 222-0741 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010 Panasonic de Mexico S.A. de C.V. Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 2127 Panasonic Sales Company Division of Matsushita Electric of Puerto Rico Inc. San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puerto Rico 00630 (787) 750-4300 © 2002 Matsushita Electric Industrial Co., Ltd. All rights reserved.