Panasonic Digital Video Camcorder PV-GS300 Operating Instructions

							Record mode
31LSQT0974
Recording still pictures onto a card 
(Photoshot) 
≥Set to Card Recording Mode.
≥The lens cover opens automatically.
1Press the [PHOTO SHOT] button halfway in 
order to adjust focusing. (For auto focusing 
only) 
≥If you set [O.I.S.] to [ON], then the image 
stabilizer function will be more effective. 
([ (MEGA Optical image stabilizer)] will 
be indicated.)
≥The iris/gain value is fixed and this 
Camcorder focuses on the subject 
automatically.
1 Shutter chance mark
± (The white lamp flashes.):
Focusing
¥ (The green lamp lights up.):
When in focus
No mark: When focusing is unsuccessful
≥The shutter chance mark is indicated as follows 
when the [PHOTO SHOT] button is not pressed 
halfway. Please use it as a guide for recording.
¥ (The green lamp lights up.):
When in focus and a good picture 
can be recorded
± (The white lamp lights up.):
Almost in focus
2Focus area
2Press the [PHOTO SHOT] button fully.
ª
To record still pictures clearly≥When zooming in on the subject with a 
magnification of 4k or higher, it is difficult to reduce the slight shaking from holding the 
Camcorder by hand. We recommend 
decreasing the zoom magnification and 
approaching the subject when recording.
≥When recording still pictures, hold the 
Camcorder firmly with your hands and keep 
your arms stationary at your side so as not to 
shake the Camcorder.
≥You can record stable pictures without shaking 
by using a tripod and the remote control.
≥For the number of still pictures to be recorded 
on a card, refer to -78-.
≥The moving picture and sound cannot be 
recorded.
≥While data are recorded on a card, do not 
operate the mode dial.
≥When the access lamp is lit, do not insert or 
remove a card.
≥Another product may degrade or not play back 
data recorded on this Camcorder.
≥If set [PICT.QUALITY] >> [ ], mosaic-pattern 
noise may appear on a playback image 
depending on the picture content.
≥When the [PICTURE SIZE] is set to other than 
[ ] or [ ], the mega pixel recording mode 
is set.
ª
On-screen display in the card 
recording mode
1) Still picture size
2) Card indication (-66-)
3) Number of recordable still pictures
(When no pictures can be recorded, the red 
light will flash.) 
4) Quality of still pictures
PC
MEGA
PHOTO SHOT
1
2
0.20.3M
ø÷÷ø÷÷
1)
3)
4)
2.42)
LSQT0974_ENG.book  31 ページ  ２００５年１１月７日　月曜日　午前１１時５８分 
						

							Record mode
32LSQT0974
ªSelect the size of still pictures to be 
recorded on a card
1
Set [BASIC] >> [PICTURE SIZE] >> select 
the desired picture size. 
ASPECT [16:9]:
: 2048k1152
: 640k360
ASPECT [4:3]:
: 2048k1512
: 1600k1200
: 1280k960
: 640k480
ª
Select the picture quality for 
photoshot images
1
Set [BASIC] >> [PICT.QUALITY] >> select 
the desired picture quality.
[ ]: High picture quality
[ ]: Normal picture quality
≥You can also change the picture quality on 
[ADVANCED] >> [PICT.QUALITY] in the tape 
recording mode.
ª
Recording with a shutter operation 
effect
You can add a shutter operation simulating 
sound.
1Set [ADVANCED] >> [SHTR EFFECT] >> 
[ON].
ª
About the shutter chance mark≥The shutter chance mark does not appear in 
manual focus mode.
≥When the subject is not easily focused, focus on 
the subject manually.
≥You can record still pictures on the card even if 
the shutter chance mark does not appear, but 
pictures may be recorded without being 
focused.
≥The shutter chance mark does not appear or 
has difficulty displaying in the following cases.
≥When the zoom magnification is high.
≥When the Camcorder is shaken.
≥When the subject is moving.
≥When the subject stands in front of a light 
source.
≥When close subjects and far subjects are 
included in the same scene.
≥When the scene is dark.
≥When there is a bright part in the scene.
≥When the scene is filled with only horizontal 
lines.
≥When the scene lacks contrast.ª
Concerning the focusing area≥When there is a contrasting object ahead or 
behind the subject in the focus area, the subject 
may not be focused. If so, move the contrasting 
object out of the focus area.
≥Even when it is still difficult to focus, adjust the 
focus manually.
Zoom in/out function
You can zoom in up to 10k optically.
≥Set to Tape/Card Recording Mode.
1Wide-angle recording (zoom out):
Push the [W/T] lever towards [W].
Close-up recording (zoom in):
Push the [W/T] lever towards [T].
≥When zooming in and taking a picture while 
holding the Camcorder by hand, we recommend 
using the image stabilizer function.
≥When you are zooming on a faraway subject, a 
sharper focus is achieved if the recording 
subject is 1 meter (3 feet) or further from the 
Camcorder.
≥When the zoom speed is high, the subject may 
not be focused easily.
≥When the zoom magnification is 1k, the 
Camcorder can focus on a subject approx. 
3.5 cm (1.4 inches) away from the lens.
2.40.2
3.1M2M1M0.3M
VOL
1t t WT
5t t WT
1010t t WT
LSQT0974_ENG.book  32 ページ  ２００５年１１月７日　月曜日　午前１１時５８分 
						

							Record mode
33LSQT0974
ªDigital zoom functionIf the zoom magnification exceeds 10 times, then 
the digital zoom function will be activated. The 
digital zoom function allows you to select a 
magnification from 25k to 700k.
≥Set to Tape Recording Mode.
1Set [ADVANCED] >> [D.ZOOM] >> [25k] or 
[700k].
[OFF]: Optical zoom only (Up to 10k)
[25k]: Digital zoom (Up to 25k)
[700k]: Digital zoom (Up to 700k)
≥The larger the digital zoom magnification, the 
more the image quality is degraded.
≥When the Card Recording mode is used, the 
digital zoom function cannot be used.
ª
About the variable speed zoom 
function
≥When pushing the [W/T] lever as far as it will go, 
you can zoom from 1k to 10k in 2.5 seconds 
(maximum).
≥The zoom speed varies according to the amount 
of movement of the [W/T] lever.
≥The variable speed zoom function cannot be 
used with the remote control.
ª
To use the zoom microphone functionInterlocked with the zooming operation, the 
microphone will clearly capture sounds far away 
with the tele-shot or those in the vicinity with the 
wide-angle shot.
≥Set to Tape Recording Mode.
1Set [ADVANCED] >> [ZOOM MIC] >> [ON].
Recording yourself
You can record yourself while viewing the LCD 
monitor. You can record persons in front of the 
Camcorder while presenting them the image. The 
image is horizontally flipped as if you see a mirror 
image. (The image to be recorded is the same as 
that recording.) 
≥Extend the viewfinder to see the picture 
while recording.
1Rotate the LCD monitor towards the lens side.
≥When the Wide function is set, a vertically oriented 
display appears on the viewfinder screen, this is 
normal and not indicative of any trouble.
≥When the LCD monitor is rotated towards the 
lens side, the icon will not be displayed even if 
you push the center of the joystick.
Backlight compensation function
This protects a backlit subject from being darkened.≥Set to Tape/Card Recording Mode.1Press the joystick to display the icon. Move 
the joystick down until icon 1 appears.
2Move the joystick up to select the backlight 
compensation icon [ ].
≥The [BACKLIGHT COMPENSATION ON] 
indication appears on the screen of the 
Camcorder.
≥The image on the screen will become 
brighter.
ª
To return to normal recordingSelect the [ ] icon again.
≥The [BACKLIGHT COMPENSATION OFF] 
indication appears on the screen of the 
Camcorder.
≥If you turn off the power or operate the mode 
dial, the backlight compensation is canceled.
5050t t WT
ZOOM
1ª
LSQT0974_ENG.book  33 ページ  ２００５年１１月７日　月曜日　午前１１時５８分 
						

							Record mode
34LSQT0974
MagicPix functions
This function allows you to record color subjects 
in dark locations to stand out against the 
background.
Attach the Camcorder to a tripod, and you can 
record images free from vibration.
≥Only manual focusing can be used.
≥Recorded scene is seen as if frames were 
missed.
MagicPix function
You can record dark locations brightly in color.
0 Lux MagicPix function
You can record completely dark locations with the 
light of the LCD monitor.
≥Set to Tape Recording Mode.
1Press the joystick to display the icon. Move 
the joystick down until icon 1 appears.
2Move the joystick up to select the MagicPix 
icon [ ].
≥The [MAGICPIX ON] indication appears on 
the screen of the Camcorder.
≥Each upward press switches the modes.
OFF # MagicPix function # 0 Lux MagicPix 
function # OFF
3(In the case of 0 lux MagicPix function) 
Extend the viewfinder and rotate the LCD 
monitor towards the lens side.
≥When the LCD monitor is reversed, the 
screen is lit in white.
≥Extend the viewfinder and view the images 
while recording.
≥The light of the LCD monitor reaches approx. 
1.2 m (3.9 feet) or less.ª
To cancel the MagicPix functionSelect the MagicPix icon until the MagicPix 
indication disappear.
≥The [0 LUX MAGICPIX OFF] indication appears 
on the screen of the Camcorder.
≥If the 0 lux MagicPix function is selected without 
reversing the LCD monitor, the [REVERSE THE 
LCD MONITOR] indication appears.
≥If set in a bright place, the screen may become 
whitish for a while.
≥The MagicPix function makes the signal 
charging time of CCD up to approximately 30k 
longer than usual, so that dark scenes invisible 
to the naked eye can be recorded brightly. For 
this reason, bright dots that are usually invisible 
may be seen, but this is not a malfunction.
≥The MagicPix function is canceled when you 
turn off the power or operate the mode dial.
Soft skin mode
This allows the skin color to be recorded in a 
softer tone. This is more effective if you record the 
bust image of a person.
≥Set to Tape/Card Recording Mode.
1Press the joystick to display the icon. Move 
the joystick down until icon 1 appears.
2Move the joystick left to select the soft skin 
icon [ ].
≥The [SOFT SKIN MODE ON] indication 
appears on the screen of the Camcorder.
ª
To cancel the soft skin modeSelect the [ ] icon again.
≥The [SOFT SKIN MODE OFF] indication 
appears on the screen of the Camcorder.
≥If the background or anything else in the scene 
has colors similar to the skin color, they will also 
be smoothed.
≥If the brightness is insufficient, the effect may 
not be clear.
1
1
LSQT0974_ENG.book  34 ページ  ２００５年１１月７日　月曜日　午前１１時５８分 
						

							Record mode
35LSQT0974
Tele macro function
By focusing only on the subject and blurring the 
background, the image can be impressive. This 
Camcorder can focus on the subject at a distance 
of approx. 50 cm (20 inches).
≥Set to Tape/Card Recording Mode.
1Press the joystick to display the icon. Move 
the joystick down until icon 1 appears.
2Move the joystick right to select the 
tele-macro icon [ ].
≥The [TELE MACRO ON] indication appears 
on the screen of the Camcorder.
≥If the magnification is 10k or less, then it is 
automatically set to 10k.
ª
To cancel the tele macro functionSelect the [ ] icon again.
≥The [TELE MACRO OFF] indication appears on 
the screen of the Camcorder.
≥If a sharper focus cannot be achieved, adjust 
the focus manually. 
≥In the following cases, the tele macro function is 
canceled.
≥The zoom magnification becomes lower than 
10k.
≥The power is off or the mode dial is operated.
Fade in/fade out function
Fade in
The image and audio gradually appear.
Fade out
The image and audio gradually disappear.
≥Set to Tape Recording Mode.
1Press the joystick to display the icon. Move 
the joystick down until icon 1 appears.
2Move the joystick left to select the fade icon 
[].
≥The [FADE ON] indication appears on the 
screen of the Camcorder.
3Press the recording start/stop button.Start recording. (fade in) 
When you start recording, the image/audio 
disappeared completely and the image/audio 
gradually appears.
Pause recording. (fade out) 
The image/audio gradually disappears. After the 
image/audio completely disappears, recording 
stops.
ª
To cancel fadingSelect the [ ] icon again.
≥The [FADE OFF] indication appears on the 
screen of the Camcorder.
ª
To select the color for fade in/fade outThe color which appears in fading pictures can be 
selected.
1Set [ADVANCED] >> [FADE COLOR] >> 
[WHITE] or [BLACK].
≥While the fade in/fade out function is selected, it 
takes several seconds to display the image 
when you start recording images. Besides, it 
also takes several seconds to pause recording.
1
1B
LSQT0974_ENG.book  35 ページ  ２００５年１１月７日　月曜日　午前１１時５８分 
						

							Record mode
36LSQT0974
Wind noise reduction function
This reduces the wind noise coming into the 
microphone when recording.
≥Set to Tape Recording Mode.
1Set [BASIC] >> [WIND CUT] >> [ON].
ª
To cancel the wind noise reduction 
function
Set [BASIC] >> [WIND CUT] >> [OFF].
≥The default setting is [ON].
≥Reduces the wind noise depending on the wind 
strength. (If this function is activated in strong 
winds, the stereo effect may be reduced. When 
the wind weakens, the stereo effect will be 
restored.) 
Auto Ground-Directional Standby 
(AGS)
This function prevents unnecessary recording 
when you forget to pause recording and walk with 
the Camcorder tilted upside down while recording 
continues. 
≥If the Camcorder continues to be tilted upside 
down from the normal horizontal position while 
recording on a tape, it is automatically put into 
recording pause.
[AGS]: Auto Ground-Directional Standby
≥Set to Tape Recording Mode.
Set [SETUP] >> [AGS] >> [ON].
ª
To cancel Auto Ground-Directional 
Standby
Set [SETUP] >> [AGS] >> [OFF].
≥The AGS function may activate and cause the 
Camcorder to pause the recording if you are 
recording a subject right above or right below 
you. In these cases, set [AGS] >> [OFF] then 
continue the recording.≥Use the recording start/stop button to pause or 
stop the recording. The AGS function is only a 
backup function for when you forget to pause 
the recording. 
≥The time it takes the Camcorder to be put into 
recording pause after being titled upside down 
varies depending on the operating conditions.
Using the built-in flash
Use the built-in flash in order to record still 
pictures in dark places.
≥Set to Tape/Card Recording Mode.
1Set [ADVANCED] >> [FLASH] >> [ß] or [ßA].
≥If [ßA] is selected, then the flash will 
automatically flash as necessary.
2Press the [PHOTO SHOT] button.
≥The flash is activated and the picture will be 
recorded.
≥You cannot use the built-in flash unless the card 
is inserted in the Camcorder.
≥The Camcorder, even when its flash has been 
turned off, automatically determines if the flash 
is necessary by detecting the ambient 
brightness. (If it determines that the flash is 
necessary, the [ ] indication lights up in 
yellow.) 
≥When the [ß] ([ßi]/[ßj]) indication or the [ßA] 
([ßAi]/[ßAj]) indication is displayed, the flash 
can be lit. If the indication is flashing or not 
displayed, the flash cannot be lit. You can take a 
picture even if the indication is flashing.
≥The available range of the flash is approx. 
1 meter to 2.5 meters  (3 feet to 7.5 feet) in a 
dark place. Pictures will appear dark or reddish 
when they are recorded by using the flash at 
distances greater than 2.5 meters (7.5 feet ). 
≥When set [FLASH] >> [ßA] and the shutter 
speed, iris or gain is adjusted, the indication 
(either [ßA], [ßAi], or [ßAj]) may disappear 
and the flash may not be lit.
≥Using the flash fixes the shutter speed of 1/750 
s or faster to 1/500.
≥The picture may become out of focus in a dark 
place. If so, adjust the focus manually.
PHOTO SHOT
LSQT0974_ENG.book  36 ページ  ２００５年１１月７日　月曜日　午前１１時５８分 
						

							Record mode
37LSQT0974
≥The picture may appear dark if flash is lit in front 
of a white background.
≥Set the flash to [ ] where using a flash is 
prohibited.
≥Do not block the flash by hand or any other 
means.
ª
When the flash is not usedSet [ADVANCED] >> [FLASH] >> [ ].
ª
To adjust the brightness of the flash
1Set [ADVANCED] >> [FLASH LEVEL] >> 
select the desired brightness level.
[ßj]: If the brightness is too high ([ßj] or 
[ßAj] indication will appear.) 
[ßd0]: In normal recording (the [ß] or [ßA] 
indication will appear.) 
[ßi]: If the brightness is insufficient ([ßi] 
or [ßAi] indication will appear.) 
ª
Red eye reduction functionReduces the phenomena where human eyes 
become red from flashes.
1Set [ADVANCED] >> [RED EYE] >> [ON].
≥
The [ ] indication appears.≥The flash is activated 2 times. Do not move until 
the second flash is finished.
≥Use this when you take pictures of people in 
dark places.
≥Red eye phenomenon may appear depending 
on the recording conditions.
Self-timer recording
You can record still pictures on a card using the 
timer.
≥Set to Card Recording Mode.
1Press the joystick to display the icon. Move 
the joystick down until icon 1 appears.
2Move the joystick left to select the self-timer 
recording icon [ ].
≥The [SELF-TIMER ON] indication appears on 
the screen of the Camcorder.
3Press the [PHOTO SHOT] button.
≥After the recording lamp and the [ ] 
indication flashes for approx. 10 seconds, 
recording will start. After recording, the 
self-timer will be canceled.
≥If you press the [PHOTO SHOT] button 
halfway and then fully, the subject is focused 
when the button is pressed halfway.
≥When you press the [PHOTO SHOT] button 
fully, the subject is focused just before 
recording.
ª
To stop the timer midway throughPress the [MENU] button.
≥The self-timer standby mode is canceled when 
you turn off the power or operate the mode dial.
≥If the RapidFire Consecutive Photoshot 
recording is set, the maximum recordable 
pictures (max. 10 pictures) are recorded.
A
1
PHOTO SHOT
LSQT0974_ENG.book  37 ページ  ２００５年１１月７日　月曜日　午前１１時５８分 
						

							Record mode
38LSQT0974
Wide/4:3 function
This allows you to record images compatible with 
wide-screen TVs.
Wide Function
Images are recorded with a 16:9 aspect ratio.
4:3 Function
Images are recorded with a 4:3 aspect ratio.
≥Set to Tape/Card Recording Mode.
1Wide Function
Set [BASIC] >> [ASPECT] >> [16:9].
4:3 Function
Set [BASIC] >> [ASPECT] >> [4:3].
ª
To Cancel the Wide/4:3 FunctionWide Function
Set [BASIC] >> [ASPECT] >> [4:3].
4:3 Function
Set [BASIC] >> [ASPECT] >> [16:9].
≥The default setting is [16:9].
≥In the wide-screen mode, the menu screens, 
operation icons and other screen displays 
appear horizontally oriented.
≥When images are played back on a TV screen, 
the date/time indication may be erased in some 
cases.
≥Depending on the TV, the picture quality may 
deteriorate.
≥If still pictures recorded with a 4:3 aspect ratio 
are played back when [TV ASPECT] is set to 
[16:9], part of the operation icons and other 
displays will appear on the black bands on the 
left and right of the picture. 
≥Concerning the TV to be connected and TV 
used for playback
≥When playing back images taken by this unit 
on a TV screen, change the setting 
established by Tape/Card playback mode 
[SETUP] >> [TV ASPECT] to match the 
aspect ratio (4:3 or 16:9) of the TV monitor to 
be connected. (
-45-)≥Depending on the settings of the TV 
connected, the images may not be displayed 
properly. For more information, please read 
the operating instructions for the TV.
Optical image stabilizer function
On this model, [O.I.S.] is used as the indication 
for Optical Image Stabilizer.
Reduces the jitter caused by hand movement 
when recording.
≥Set to Tape/Card Recording Mode.
1Set [ADVANCED] >> [O.I.S.] >> [ON].
ª
To cancel the image stabilizer functionSet [ADVANCED] >> [O.I.S.] >> [OFF].
≥When recording still pictures in the Card 
Recording mode, pressing the [PHOTO SHOT] 
button halfway increases the effect of the image 
stabilizer function. (MEGA Optical Image 
Stabilizer) 
≥When a tripod is used, we recommend that you 
turn the image stabilizer off.
≥In the following cases, the image stabilizer 
function may not work effectively.
≥When the digital zoom is used
≥When the Camcorder is shaken greatly
≥When you record a moving subject while 
tracking it
O.I.S.
LSQT0974_ENG.book  38 ページ  ２００５年１１月７日　月曜日　午前１１時５８分 
						

							Record mode
39LSQT0974
RapidFire Consecutive Photoshot
Records still pictures continuously at a certain 
interval.
≥Set to Card Recording Mode.
1Set [BASIC] >> [PICTURE SIZE] >> [ ] or 
[] .
2Set [ADVANCED] >> [BURST MODE] >> 
[ON].
3Press and hold the [PHOTO SHOT] button.
ª
To stop RapidFire Consecutive 
Photoshot midway through
Release the [PHOTO SHOT] button.
≥You can press the [PHOTO SHOT] button 
halfway and then start RapidFire Consecutive 
Photoshot. (Focusing is fixed. If the image 
stabilizer function is turned on, then MEGA 
Optical Image Stabilizer will be activated.) 
≥The Camcorder records up to 10 still pictures at 
intervals of 0.5 seconds. (If the shutter speed is 
manually set to 1/30, then the still pictures can 
be recorded at intervals of 0.7 seconds.)
≥One more still picture may be recorded after you 
release the [PHOTO SHOT] button.
≥This is not mega pixel still-picture recording.
≥The flash is not used.
≥If the self-timer is set, the Camcorder records up 
to 10 still pictures continuously.
≥Intervals between recording pictures may 
become longer depending on the card. We 
recommend using a Panasonic SD Memory 
Card.
≥When using the card formatted by other 
equipment or a card that was recorded and 
erased repeatedly, the intervals between 
recording pictures may become longer. If so, 
back up your important data on a PC, and 
format your card with this Camcorder.
Recording in various situations 
(Scene mode)
When you record images in different situations, 
this mode automatically sets optimum shutter 
speeds and apertures.
≥Set to Tape/Card Recording Mode.
1Set the [AUTO/MANUAL/FOCUS] switch to 
[MANUAL].
2Set [BASIC] >> [SCENE MODE] >> select the 
desired mode.
1) [5] Sports mode
≥To record sports scenes or scenes where 
there are quick motions
2) [ ] Portrait mode
≥To make people stand out against the 
background
3) [ ] Low light mode
≥To record dark scenes so they are brighter
4) [ ] Spotlight mode
≥To record subjects spotlit in a party or 
theater
5) [ ] Surf & snow mode
≥To record images at dazzling places such 
as ski slopes and beaches
ª
To cancel the scene mode functionSet [BASIC] >> [SCENE MODE] >> [OFF] or set 
the [AUTO/MANUAL/FOCUS] switch to [AUTO].
Sports mode
≥For slow-motion playback or playback pause 
of recorded pictures, this mode presents free 
of Camcorder shakes.
0.20.3M
PHOTO SHOT
AUTO
MANUAL
FOCUS
3)
1)
5)
2)
4)
LSQT0974_ENG.book  39 ページ  ２００５年１１月７日　月曜日　午前１１時５８分 
						

							Record mode
40LSQT0974
≥During normal playback, the image 
movement may not look smooth.
≥Avoid recording under fluorescent light, 
mercury light or sodium light because the 
color and brightness of the playback image 
may change.
≥If you record a subject illuminated with strong 
light or a highly reflective subject, vertical 
lines of light may appear.
≥If the brightness is insufficient, the sports 
mode does not function. The [5] indication 
flashes.
≥If this mode is used indoors, the screen may 
flicker.
Portrait mode
≥If this mode is used indoors, the screen may 
flicker. If so, change the scene mode setting 
to [OFF].
Low light mode
≥Extremely dark scenes may not be able to be 
recorded finely.
Spotlight mode
≥If the recording subject is extremely bright, 
the recorded image may become whitish and 
the periphery of the recorded image 
extremely dark.
Surf & snow mode
≥If the recording subject is extremely bright, 
the recorded image may become whitish.
Recording in natural colors 
(White balance) 
The automatic white balance function may not 
reproduce natural colors depending on the 
scenes or lighting conditions. If so, you can adjust 
the white balance manually.
≥Set to Tape/Card Recording Mode.
1Set the [AUTO/MANUAL/FOCUS] switch to 
[MANUAL].
2Move the joystick up to select the white 
balance icon [ ].
3Move the joystick left or right in order to 
select the white balance mode.
1) Auto white balance adjustment [ ]
2) Indoor mode (for recording under 
incandescent lamps) [ ]
3) Outdoor mode [ ]
4) Manual adjustment mode [ ]
ª
To restore to the automatic 
adjustment
Move the joystick left or right until the [ ] 
indication appears. Or, set the [AUTO/MANUAL/
FOCUS] switch to [AUTO].
≥When setting both the white balance and the 
iris/gain, set the white balance first.
≥Whenever recording conditions change, re-set 
the white balance for correct adjustment.
ª
To set the white balance manuallySelect [ ] in Step 3. Then, while viewing a white 
subject on the entire screen, move the joystick up 
to select the [ ] indication.
ª
About flashing of the [ ] indicationWhen the manual adjustment mode is 
selected
≥Flashing indicates that the white balance 
previously adjusted is stored. This setting is 
stored until the white balance is adjusted again.
When white balance cannot be set in the 
manual adjustment mode
≥White balance may not be adjusted properly in 
the manual adjustment mode in dark places. If 
so, use the auto white balance mode.
During setting in the manual adjustment mode
≥When the setting is completed, it will keep lit.
ª
About the white balance sensorThe white balance sensor detects the type of light 
source during recording.
≥Do not cover the white balance sensor during 
recording, or it may not function properly.
ª
About the black balance adjustmentThis is one of the 3CCD system functions that 
automatically adjusts the black when the white 
balance is set in the manual adjustment mode. 
AUTO
MANUAL
FOCUS
MNL
11
11AW B
3) 1)
2)
4)
AWB
AWB
LSQT0974_ENG.book  40 ページ  ２００５年１１月７日　月曜日　午前１１時５８分