Panasonic Digital Hd Video Cassette Recorder Ajhd1500p Operating Instructions

– 41 –
Preview
1After the edit points have been entered, press the PREVIEW button.
Normal preview is now performed.

•If the edit IN point has not been entered, the position where the PREVIEW button was
pressed will be entered at the edit IN point.
•To stop the preview at any time, press the STOP button.
•If the PREVIEW button is pressed again while preview is in progress after the IN point,
preview will start again from the beginning.
•When the edit OUT point is reached, the unit automatically goes into...

– 42 –
Automatic editing (deck to deck)
Executing automatic editing
1Press the AUTO EDIT button.
Automatic editing is now performed.
•To stop the editing at any time, press the STOP button.
•When the edit OUT point is reached, the unit goes into the stop mode after postrolling.
Postroll
With assemble editing, editing continues for approx. 2 seconds even after the edit OUT point
has been passed, the tape is rewound to the OUT point, and the unit goes into the stop
mode.
With insert editing, the unit goes...

– 43 –
Review
1Upon completion of the editing, press the REVIEW button.
The review is started in the recorder.
•To stop the review at any time, press the STOP button.
•When the edit OUT point is reached, the unit goes into the stop mode after postrolling.
PULL FOR VARIABLE
ON
AUDIO CH SELECTSHIFT ADJTC  SETSTART TC/CTLRESET
TC INTTCTAPE
UB
STAND BY
EDIT PLAY
REW STOPSERVOREC
FFREC INHIBIT
PLAYEREXT EE
MODEREMOTEPUSH
REV FWDRECORDERLOCAL
CONTROL
CH 1
1ASMBL
PREVIEW
REVIEWAUTO EDITPREROLLTRIMA ININSETOUTA...

– 44 –
Audio split editing
The video edit points and audio edit points can be entered separately, and they can be offset
from each other and edited.
The audio edit points cannot be entered when the assemble editing mode has been
selected. After the edit points have been entered, follow the same operating procedure as
that for insert editing.

Entering the edit points
Video IN point: Press the SET button while holding down the IN button.
Video OUT point: Press the SET button while holding down the OUT...

– 45 –
Audio split editing

Displaying the audio split edit points
The edit points are displayed on the front panel as shown below. (The figure shows an audio
IN point.)
Operations
Video IN point: Press the IN button.
Video OUT point: Press the OUT button.
Audio IN point: Press the A-IN button.
Audio OUT point: Press the A-OUT button.

If the editing mode is switched to assemble editing after audio edit points have entered,
these points will be deleted.

Cueing up the tape to the edit points
Cue-up to...

– 46 –
Expansion mode execution using the MODE/SEL button
When the MODE/SEL button g is pressed, the MULTI CUE operation mode which is an expansion
mode can be established as shown in the diagram below.
 status
When the MODE/SEL button g is pressed in the normal mode, the following appears on the front top
display.
When SCROLL button 5 is pressed, it causes IC CARD # VAR MEMO ... change in order. Select a
desired mode and press ENTER button 6. status Normal mode
MODE/SEL button g
ENTER
Button 6
MULTI CUE...

– 47 –
MULTI CUE function
Selecting the MULTI CUE mode
The MULTI CUE mode can be selected from the  status established by
pressing the MODE/SEL button g.
When the EXIT button h is pressed, the MULTI CUE mode is released, and the normal mode is
restored.
Editing channels
In handling the cue points, the edit CH selection buttons (ASMBL, VIDEO, CH1/5, CH2/6, CH3/7, CH4/
8, CUE, TC) can be used for CUE¢1 through CUE¢8, respectively.
Registering the cue points
A total of 80 cue points can be registered on a...

– 48 –
M
#L
ST
EAC
RU
CE
H0 11
!2:3
E4
N:
T5
R6
Y:
20
30
MULTI CUE function
Description of displays
When MULTI CUE is selected using the MODE/SEL button g, the following appears on the front top
panel display 3.
1Mode display: This indicates that the unit is now operating in the MULTI CUE mode.
2Time display: This indicates the time of the search point or registration point.  (This display is blank
when no data is available.)
3Display mode selection mark: This shows whether the current LED and time data...

– 49 –
MULTI CUE function
Search point and registration point operations
Each time the SHIFT button 8 is pressed, the search point display mode and registration point display
mode are selected alternately.  Perform the search point operations in the search point display mode
and the registration point operations in the registration point display mode.
•When the power is turned on, the search and registration points established are the ones which were
in place when the power was last turned off.
•When the...

– 50 –
MULTI CUE function
Example of top panel display: One of the following two displays appears depending on the registration
conditions.
•The registration pointer position is changed directly on the same page by pressing the CUE¢1
through ¢8 (ASMBL through TC) buttons.
•When the display page has been changed using the scroll buttons, operation is as follows depending
on the setup menu item No.131 (PAGE MODE) setting.
When MANU has been set:Both the search and registration pointers move to CUE¢1 on the...