Panasonic Digital Camera Dmc Lx1 Owners Manual

							Playback (advanced)
101VQT0S19
2Enlarge or decrease the picture.
3Shift the picture and press the 
shutter button fully to set.
4Select [YES] or [NO] and set it.
• When you select [YES], the picture is 
overwritten.
When trimmed pictures are overwritten, 
they cannot be restored.
• When the original picture is protected, you 
cannot overwrite the trimmed picture.
When you select [NO], a trimmed picture 
is newly created.
• It may not be possible to trim pictures 
recorded with other equipment.
• The picture quality of the trimmed picture 
may be deteriorated.
• If you trim a picture, the number of pixels 
may be fewer in the trimmed picture than 
in the original.
100_
00011/19
TRIMMING
ZOOMEXITMENU
EXITTRIM:SHUTTER
100_
00011/19
TRIMMING
ZOOMMENU
SELECT SET CANCEL
TRIMMING
DELETE ORIGINAL
PICTURE?
MENU
MENU
NO
YES
2 times 
						

							Playback (advanced)
102VQT0S19
For menu operations, see page 90.  
Resize pictures taken in 16:9 aspect ratio 
for printing to 3:2 or 4:3.
1Select [ ] or [h] and set it.
2Select the picture.
3Move the frame to trim the 
picture.
4Select [YES] or [NO] and set it.
• When you select [YES], the picture is 
overwritten. 
When pictures with changed aspect ratio 
are overwritten, they cannot be restored.
• When the original picture is protected, you 
cannot overwrite the pictures with the 
changed aspect ratio. When you select 
[NO], a picture with the changed aspect 
ratio is newly created.
• You cannot change the aspect ratio of 
pictures taken as [TIFF] or [RAW], motion 
pictures, or still pictures with audio.
• You may end up with a higher-resolution 
picture after changing to a different aspect 
ratio. 
Changing the Aspect Ratio 
[ASPECT CONV.]i
EXITMENUSELECTPROTECT
TRIMMING
ASPECT CONV.
PLAY2
3
RESIZE AUDIO DUB.
3:24:3
SELECTSELECTEXITEXITSETSET
100_00011/19
TASPECT       CONV.
MENU
SET:SHUTTER ADJUST.EXITMENU
SELECT SET CANCEL
ASPECT CONV.
DELETE ORIGINAL
PICTURE?
MENU
MENU
NO
YES
2 times 
						

							Playback (advanced)
103VQT0S19
For menu operations, see page 90. 
Use this to speed up you SD card’s transfer 
speed if it becomes noticeably slower.
This normally happens after shooting and 
erasing repeatedly. Reduced transfer 
speed can especially effect the recording of 
motion pictures, where recording can be 
interrupted. Clean up the card beforehand 
for best results.
1Select [YES] to clean up.
• Cleanup increases the transfer speed of 
the available memory on the card and 
does not erase any of your images or 
other data.
• Cleanup can take some time to complete.
• Cleanup may have no noticeable effect on 
some kinds of card.
• Cleanup cannot be used on MultiMedia 
Cards.
• Do not turn the camera off during cleanup.
• When you cleanup the card, use a battery 
with sufficient battery power (P14) or AC 
adaptor (DMW-AC5; optional).
• Make sure the SD memory card’s write-
protect switch is not engaged.For menu operations, see page 90.
 
1Select [YES] to format.
• Usually, it is not necessary to format the 
card. Format the card when the message 
[MEMORY CARD ERROR] appears.
• Do not format the card on a computer. 
Always format on the camera.
• Once the card is formatted, all data 
including protected images are 
irretrievably erased. Please confirm that 
all data is transferred to your PC before 
proceeding with format function.
• During formatting, do not turn the camera 
off.
• When you format the card, use a battery 
with sufficient battery power (P14) or AC 
adaptor (DMW-AC5; optional).
• When the SD Memory Card Write-Protect 
switch is slid to [LOCK], you cannot 
format the card.
• If the card cannot be formatted, consult 
your nearest servicenter.
Clean up the Card [CLEAN UP]<
SELECT SET
YESNO
CLEAN UP
CLEAN UP THE CARD?
Initializing the Card [FORMAT]
For USA assistance, please call: 1-800-272-7033 or 
send e-mail to : [email protected]
For Canadian assistance, please call: 
1-800-561-5505 or visit us at www.panasonic.ca
0
SELECT SET
FORMAT
DELETE ALL DATA
ON THE MEMORY CARD?
YESNO 
						

							Playback (advanced)
104VQT0S19
Playing Back Pictures with a TV Screen
 
nPlaying back pictures with the 
supplied cable
• Turn the camera and the TV off.
• Set the [TV ASPECT]. (P26)
1Connect the AV cable A 
(supplied) to the [AV OUT] socket 
of the camera.
• Connect the AV cable with the [f] 
mar k  fac in g the [w] mark on the [AV OUT] 
socket.
• Hold 
B and then insert or pull the AV 
cable straight.
2Connect the AV cable to the video 
input and the audio input sockets 
of the TV.
• 1 Yellow: to the video input socket
• 
2 White: to the audio input socket
3Turn the TV on and select external 
input.
4Turn the camera on and then set 
the mode dial to playback mode 
[
Q].
• You can display pictures on a TV only 
when the mode dial is set to playback 
mode [Q].
nViewing pictures in other countries
When setting [VIDEO OUT] on the menu, 
you can view pictures on a TV in other 
countries (regions) which use the NTSC or 
PAL system.
• Even if you set menu selection for [VIDEO 
OUT] to [PAL], the output signal is still 
NTSC in the recording mode.
nPlayback pictures on TV with SD 
Memory Card slot
You can put your SD Memory Card in a 
television with an SD Memory Card slot to 
show still images. (Depending on the 
television, some pictures may not take up 
the whole screen).
• You cannot play motion pictures. Use the 
included AV cable when playing motion 
pictures. (See left)
• You may be unable to play MultiMedia 
Cards, even if the television has an SD 
Memory Card slot.
• Do not use any other AV cables except 
the supplied one.
• Read the TV operating instructions too.
• Audio playback is in monaural.
• Pictures might be slightly blurred if you 
show them vertically on a television 
(connected with the included AV cable).
A B
1 2 
						

							105VQT0S19
Connecting to a PC or Printer
Before Connecting with USB Connection Cable 
[4 : USB MODE]
Select the USB system before connecting a 
computer or printer to the camera with the 
USB connection cable (supplied). 
Set the items on [USB MODE] in the 
[SETUP] menu. (P25)
1Select [USB MODE].
2Select [PC] or [PictBridge (PTP)].
• If you connect the camera to a PC, select 
[PC]. (P106)
• If you connect the camera to a printer 
supporting PictBridge, select [PictBridge 
(PTP)]. (P108)
• When [PC] is selected, the camera is 
connected via USB Mass Storage 
communication system. 
• When [PictBridge (PTP)] is selected, the 
camera is connected via PTP (Picture 
Transfer Protocol) communication system.
• If you have connected with a USB 
connection cable, [PICTURE IS 
DISPLAYED FOR 4:3 TV FOR 16:9 
SETUP q TV ASPECT] or similar may be 
shown but this is normal.
MENU
SETUP
SELECT EXITUSB  MODE
MF m/ft HIGHLIGHT
VIDEO OUT
TV ASPECT
PC
OFF
ft
NTSC
MENU
34
4:3
USB MODE
SELECT SET
PC
PictBridge
(PTP)
MENU 
						

							Connecting to a PC or Printer
106VQT0S19
Connecting to a PC
• By connecting the camera to a computer, 
you can upload your pictures, then use 
the software on the included CD-ROM 
([LUMIX Simple Viewer] and 
[PHOTOfunSTUDIO] for Windows
®) to 
print or send your images by e-mail.
• If you use Windows 98/98SE, install the 
USB driver and then connect it to the 
computer.
• For details about [LUMIX Simple Viewer] 
and installation, refer to the separate 
operating instructions for PC connection.
A : AC adaptor (DMW-AC5; optional)
• Make sure this unit is off before 
connecting or disconnecting the AC 
adaptor (DMW-AC5, optional).
B : USB connection cable (supplied)
C : This message appears during data 
transfer.
DE: Check the facing of the connector and 
push straight in.
1Switch the camera on and set 
[USB MODE] to [PC] in the setup 
menu (P105).
• If you have set [USB MODE] to 
[PictBridge (PTP)], the computer may 
show an error message. 
Click [Cancel] to close the dialog and 
disconnect the cable from the computer. 
Change the setting to [PC] and reconnect 
the cable.
2Connect the camera to a PC via 
the USB connection cable B 
(supplied).
• Connect the USB connection cable with 
the [f] mark facing the [w] mark on 
the [DIGITAL] socket.
• Hold 
D and then insert or pull the USB 
connection cable straight.
Do not try to force the connector in 
backwards or sideways. This can damage 
this unit and the equipment you are 
connecting.
[Windows]
The drive appears on the [My Computer] 
folder.
• If it is the first time you are connecting the 
camera to a PC, the required driver is 
installed automatically so that the camera 
can be recognized by the Windows Plug 
and Play, then it appears on the [My 
Computer] folder.
[Macintosh]
The drive appears as [NO_NAME] or 
[Untitled].
B DE
A
C
ACCESS 
						

							Connecting to a PC or Printer
107VQT0S19
nFolder Composition
Folders appear as follows.
1 Folder number
2 File number
3 JPG : Pictures
MOV : Motion pictures
The contents of each folder are:
• This unit stores up to 999 picture files in 
each folder. A new folder is created after 
this maximum is reached.
• To reset file and folder numbers, use 
[NO.RESET] in the setup menu. (P25)
nFolder numbers are updated when: 
• The folder containing the picture you just 
shot had a file numbered 999 in it.
• You insert a card you had been using on 
another manufacturer’s camera that has a 
file number 100 (e.g. 100_XXXXX, 
XXXXX is the manufacturer’s name, etc.) 
immediately after using a card that had a 
folder numbered 100. (That is, you insert 
a card with the same number, irrespective 
of the manufacturer.)• You start shooting again after using 
[NO.RESET] in the setup menus (P25). (It 
is recorded to a new folder that has a 
number following on from the one 
previous. You can also reset the folder 
number to 100 by using [NO.RESET] 
immediately after formatting the card 
when there are no folders or pictures on 
the card.)
• If the remaining battery power is 
exhausted during communication, the 
recorded data may be damaged. When 
you connect the camera to the PC, use a 
battery with sufficient battery power (P14) 
or the AC adaptor (DMW-AC5; optional).
• If the remaining battery power becomes 
low during communication, the alarm 
beeps. In this case, stop the 
communication immediately.
• While [ACCESS] is being displayed, do 
not disconnect the USB connection cable.
• For Windows 2000 users: Disconnect 
the USB cable before changing the 
card. Changing the card while the 
cable is still connected can damage 
the data on the card. (For details, refer 
to the separate operating instructions 
for PC connection.)
• Do not use any other USB connection 
cables except the supplied one.
• Refer to the operating instructions of the 
PC, too.
nAbout PictBridge (PTP) setting
• With Windows XP Home Edition/
Professional and Mac OS X, you can 
leave the USB mode setting as 
[PictBridge (PTP)].
• You can only load pictures from the 
camera and cannot write them on the 
card or delete them.
• When there are 1000 or more pictures on 
a card, the pictures may not be imported. DCIM 100_PANA to 999_PANA
100_PANA Pictures/Motion pictures
MISC File with DPOF or favorite 
setting
PRIVATE1 Flip animation files
DCIM
MISC
PRIVATE1
100_PANA
101_PANA
999_PANAP1000001.JPG
P1000002.JPG
P1000999.JPG
100_PANA
1
23
SD Memory 
Card
MultiMedia 
Card 
						

							Connecting to a PC or Printer
108VQT0S19
Connecting to a PictBridge-compliant Printer
By connecting the camera directly to a 
printer supporting PictBridge via the USB 
connection cable (supplied), you can select 
the pictures to be printed or start printing 
on the LCD monitor.
Make the necessary settings on your 
printer beforehand. (Read your printer’s 
operating instructions.)
A : USB connection cable (supplied)
B : AC adaptor (DMW-AC5; optional)
• Make sure this unit is off before 
connecting or disconnecting the AC 
adaptor (DMW-AC5, optional).
1Turn the camera on and then set 
the USB mode to [PictBridge 
(PTP)]. (P105)
2Turn on the printer.
3Connect the camera to a printer 
via the USB connection cable A  
(supplied).
• Connect the USB connection cable with 
the [f] mark facing the [w] mark on 
the [DIGITAL] socket.
• Hold 
C and then insert or pull the USB 
connection cable straight.
• If the remaining battery power becomes 
low during communication, the alarm 
beeps. In this case, stop the 
communication immediately. 
• It may take time to print some pictures. 
Therefore, we recommend using a battery 
with sufficient power (P14) or the AC 
adaptor (DMW-AC5; optional) when you 
connect to a printer.
• Disconnect the USB connection cable 
after printing.
• Do not use any other USB connection 
cables except the supplied one.
• If you also want to print your baby’s age 
(added with the [BABY] (P65) scene 
mode), use [LUMIX Simple Viewer] or 
[PHOTOfunSTUDIO] (on the included 
CD-ROM). (For details, refer to the 
separate operating instructions for PC 
connection.)
A
C
B
When the DPOF 
Print is set. (P95)Select [DPOF 
PICTURE]. (P110)
When the DPOF 
Print is not set.Select [SINGLE 
PICTURE]. (P109) 
						

							Connecting to a PC or Printer
109VQT0S19
nSingle picture
1Select a picture to be printed.
• A message displays for about 2 seconds.
2Set the print settings.
• The items which are not supported by the 
printer are displayed in gray and cannot 
be selected.
• When you want to print pictures in a paper 
size or a layout which is not supported by 
the camera, set [PAPER SIZE] and [PAGE 
LAYOUT] to [F] and then set the paper 
size or the layout on the printer. (For 
details, refer to the operating instructions 
of the printer.)
n[PRINT WITH DATE]
• If the printer does not support date 
printing, the date cannot be printed on the 
picture. 
n[NUM. OF PRINTS]
Set the number of prints.
n[PAPER SIZE]
(Possible paper sizes on the camera)
The items are listed on 1/2 and 2/2.
Press r to select the desired item.
*These items cannot be displayed when the 
printer does not support the paper sizes.
100_
00011/19
PRINT
PLEASE SELECT
THE PICTURE TO PRINT
SELECTPictBridge
SINGLE PICTURE
SELECT CANCELPRINT WITH DATE PRINT START
NUM. OF PRINTS
PAPER SIZE
PAGE LAYOUT
1OFF
ON
SETMENU
FSettings on the printer are 
prioritized.
OFF Date is not printed.
ON Date is printed.
1/2
FSettings on the printer are 
prioritized.
L/3.5″×5″89 mm×127 mm
2L/5″×7″127 mm×178 mm
POSTCARD 100 mm×148 mm
A4 210 mm×297 mm
2/2*
CARD SIZE 54 mm×85.6 mm
10×15cm 100 mm×150 mm
4″×6″101.6 mm×152.4 mm
8″×10″203.2 mm×254 mm
LETTER 216 mm×279.4 mm 
						

							Connecting to a PC or Printer
110VQT0S19
n[PAGE LAYOUT]
(Possible layouts on the camera)
3Select [PRINT START] and then 
print out the picture.
• Press the [MENU] button to cancel 
printing.
nDPOF picture
• Set the DPOF print with this camera in 
advance. (P95)
1Select [DPOF PICTURE].
• When printing under the new settings, 
disconnect the USB connection cable and 
connect it to the printer again.
• You can change the DPOF print setting by 
pressing the [MENU] button. (P95)
2Select [PRINT START] and then 
print out the picture.
• Refer to P109 for print setting.
• Press the [MENU] button to cancel 
printing.
FSettings on the printer are 
prioritized.
G1 page with no frame print
H1 page with frame print
I2 pages print
J4 pages print
SINGLE PICTURE
SELECT CANCELPRINT WITH DATE PRINT START
NUM. OF PRINTS
PAPER SIZE
PAGE LAYOUT
1
MENU
SELECT SET
DPOF PICTURE SINGLE PICTURE
PictBridge
SELECT CANCELPAPER SIZE
PAGE LAYOUT
DPOF
PRINT START
MENU