Panasonic Digital Camera Dmc Ls2 Operating Instrutions Manual

							Menu Settings
71VQT0V10
 If you press [MENU/SET] while canceling protection, the canceling will stop halfway.
 The protect setting may not be effective 
on other equipment.
 If you want to delete protected pictures,  cancel their protection.
 Even if you protect pictures in the built-in  memory or a card, they will be deleted if 
the built-in memory or the card is 
formatted. (P74)
 Even if you do not protect pictures on an  SD Memory Card, they cannot be deleted 
when the card’s write protect switch  A is 
set to [LOCK].
 The following functions cannot be used  with protected pictures.
–[ROTATE]
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P65)
This function is useful if you want to reduce 
the file size of a picture to attach it to an 
e-mail or upload it to a website.
1 Press 2 1 to select the picture 
and then press  4.
 The following pictures cannot be 
resized.
 When the aspect ratio setting is [ ]. – Pictures recorded in [ ] (0.3M EZ)  When the aspect ratio setting is 
[].
– Pictures recorded in [ ]  (2.5M EZ)
 When the aspect ratio setting is  [].
– Pictures recorded in [ ] (2M EZ)
– Motion pictures
 It may not be possible to resize pictures  recorded with other equipment.
2 Press  21 to select the size and 
then press  4.
 Sizes smaller than the recorded picture 
are displayed.
 When the aspect ratio setting is [ ].
– [ ]/[ ]/[ ]/[ ]
 When the aspect ratio setting is  [].
–[ ]
 When the aspect ratio setting is  [].
–[ ]
3 Press  34 to select [YES] or 
[NO] and then press [MENU/SET].
 The picture is overwritten when you 
select [YES]. Resized pictures cannot 
be restored when they are overwritten.
 A resized picture is newly created when 
you select [NO].
[RESIZE]
Making the picture smaller
2
MENUSET
RESIZE
EXIT
SET SELECT
1/3
MENU
100 _
0001
RESIZE
EXIT
RESIZE SELECT
1/3100 _
0001
MENU
RESIZE
DELETE ORIGINAL
PICTURE?
NO
SELECTSETMENUCANCELMENU
SET
YES
VQT0V10ENG.book  71 ページ  ２００５年１２月２７日　火曜日　午後８時３４分 
						

							Menu Settings
72VQT0V10
 If the original picture is protected, you cannot overwrite it. Select [NO] and 
newly create a resized picture.
4 Press [MENU/SET] twice to close 
the menu.
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P65)
You can enlarge and then clip the important 
part of the recorded picture.
1Press  21 to select the picture 
and then press  4.
 Motion pictures cannot be trimmed.
 It may not be possible to trim pictures 
recorded with other equipment.
2 Enlarge or decrease the parts to 
be trimmed with the zoom lever.
3Press  3/4/2/1 to move the 
position of the part to be trimmed.
4 Press shutter button.
 The message [DELETE ORIGINAL 
PICTURE?] appears.
5 Press  34 to select [YES] or 
[NO] and then press [MENU/SET].
 The picture is overwritten when you 
select [YES]. The trimmed pictures 
cannot be restored when they are 
overwritten.
 A trimmed picture is newly created 
when you select [NO].
 When the original picture is protected,  you cannot overwrite it. Select [NO] and 
newly create a trimmed picture.
6 Press [MENU/SET] twice to close 
the menu.
\
 Depending on the cut size, the picture size 
of the trimmed picture may become 
smaller than that of the original picture.
 The picture quality of the trimmed picture  will deteriorate.
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P65)
You can copy recorded picture data from 
the built-in memory to a card or vice versa.
[TRIMMING]
Enlarging a picture and trimming it
MENUSET
TRIMMING
EXIT
SELECTSET
1/3
MENU
100_0001
ZOOMEXIT
TRIMMING
1/3100_0001
MENU
T
W
TRIM:SHUTTER ZOOMEXIT
TRIMMING
1/3100_0001
MENU
[COPY]
Copying the picture data
DELETE ORIGINAL
PICTURE?
TRIMMING
NO
SELECTSETMENUCANCEL
YES
MENU
SET
MENUSET
VQT0V10ENG.book  72 ページ  ２００５年１２月２７日　火曜日　午後８時３４分 
						

							Menu Settings
73VQT0V10
1Press 3 4 to select the copy 
destination and then press 
[MENU/SET].
:
All the picture data in the built-in 
memory are copied onto the card at 
one time.
(Perform step 3)
: One picture at a time is copied from the 
card to the built-in memory.
(Perform step 2)
2 Press 2 1 to select the picture 
and then press  4.
 When you copy picture data from the 
built-in memory to the card, all the 
pictures are selected at one time so this 
screen does not appear.
3 Press 3 to select [YES] and then 
press [MENU/SET].
(The illustration shows the screen when 
pictures are copied from the built-in 
memory to a card.)  The message [COPY THIS PICTURE 
TO BUILT-IN MEMORY?] appears when 
you copy pictures from the card to the 
built-in memor y.
 If you press [MENU/SET] while copying  pictures from the built-in memory to the 
card, the copying will stop halfway.
 Do not turn the camera off or do any  other operations before copying is 
finished. The data on the built-in 
memory or the card may be damaged 
or lost.
4 Press [MENU/SET] several times 
to close the menu.
 If you copy picture data from the built-in 
memory to a card, the screen 
automatically returns to the playback 
screen when all the pictures are copied.
 If you copy picture data from the built-in memory to a card, we recommend using a 
card which has more free space than the 
built-in memory (about 14 MB).
 It may take time to copy the picture data.
 Only pictures recorded with a Panasonic  digital camera (LUMIX) will be copied.
(Even if the pictures were recorded with a 
Panasonic digital camera, you may not be 
able to copy them if they were edited with 
a PC.)
 DPOF settings on the original picture data  will not be copied. Set the DPOF settings 
again after copying is finished. (P68)
 If a picture with the same name as the  picture to be copied exists in the copy 
destination, the picture will not be copied.
 If you copy picture data from the built-in  memory to a card which does not have 
sufficient free space, the picture data will 
only be copied halfway.
MENU
SET
PLAY2/2
SELECT
RESIZETRIMMING
PROTECT
FORMATSETMENU
COPY
COPY
EXIT
SELECTSET
1/3
MENU
100
_
0001
COPY
SELECT
SETMENUMENU SET
COPY PICTURES FROM
BUILT-IN MEMORY TO
MEMORY CARD ?
NOYES
VQT0V10ENG.book  73 ページ  ２００５年１２月２７日　火曜日　午後８時３４分 
						

							Menu Settings
74VQT0V10
Press [ ] to display the [PLAY] mode 
menu and select the item to set. (P65)
Usually, it is not necessary to format the 
built-in memory and the card. Format them 
when the message [BUILT-IN MEMORY 
ERROR] or [MEMORY CARD ERROR] 
appears.
Press 3 to select [YES] and then 
press [MENU/SET].
(The illustration shows the screen when 
the built-in memory is formatted.)
 When a card is not inserted, you can 
format the built-in memory. When a 
card is inserted, you can format the 
card.
 If you press [MENU/SET] while 
formatting the built-in memory, the 
formatting will stop halfway. (However, 
all the pictures will be deleted.)
 Formatting irretrievably deletes all the data including any protected pictures. 
Check the data carefully before 
formatting.
 If the card has been formatted on a PC or 
other equipment, format it on the camera 
again.
 Use batteries with sufficient power (P13) 
or the AC adaptor (DMW-AC6; optional) 
when formatting.
 Do not turn the camera off during 
formatting.  It may take longer to format the built-in 
memory than the card. (Max. about 
15 sec.)
 You cannot format an SD Memory Card 
when the card’s write protect switch is set 
to [LOCK].
 If the built-in memory or the card cannot 
be formatted, consult your nearest 
servicenter.
[FORMAT] 
Initializing the built-in memory or a 
card
MENUSET
FORMAT
DELETE ALL DATA
ON THE BUILT-IN MEMORY?
NO
SELECTSETMENUMENU
SETYES
For USA assistance, please call: 1-800-272-7033 
or send e-mail to : [email protected]
For Canadian assistance, please call:
1-800-561-5505 or visit us at www.panasonic.ca
VQT0V10ENG.book  74 ページ  ２００５年１２月２７日　火曜日　午後８時３４分 
						

							Connecting to other equipment
75VQT0V10
Connecting to other equipment
Connecting to a PC
You can acquire recorded pictures to a PC 
by connecting the camera and the PC.
The software [LUMIX Simple Viewer] 
(for Windows
®) in the CD-ROM (supplied) 
allows you to easily acquire pictures 
recorded with the camera to a PC, print 
them and send them by e-mail.
If you use Windows
 98/98SE, install the 
USB driver and then connect it to the 
computer.
For information about installing [LUMIX 
Simple Viewer] etc., refer to the separate 
operating instructions for PC connection.
A : USB connection cable (supplied)
B : AC adaptor (DMW-AC6; optional)
 Use batteries with sufficient battery power  or the AC adaptor (DMW-AC6; optional).
 Turn the camera off before inserting or  removing the cable for the AC adaptor 
(DMW-AC6; optional).
1 Turn on the camera and the PC.
2Connect the camera to a PC via 
the USB connection cable  A 
(supplied).
 Connect the USB connection cable with 
the [ ] mark facing the [ 1] mark on 
the [DIGITAL] socket.
 Hold the USB connection cable at  C 
and insert straight in or take straight 
out. (If you forcibly insert the USB 
connection cable at a slant or upside 
down you can deform the connection 
terminals and damage the camera or 
the connected equipment.)
D: This message appears during data  transfer.
3Press  3 to select [PC] and then 
press [MENU/SET].
 If you set [USB MODE] in the [SETUP] 
menu to [PC] in advance, it is not 
necessary to set this every time you 
connect to a PC. (P22)
 If you set [USB MODE] to [PictBridge  (PTP)] and then connect the camera to 
the PC, messages may appear on the 
screen of the PC.
Select [Cancel] to close the messages 
and disconnect the camera from the 
PC. Set [USB MODE] to [PC] again.
[Windows]
The drive appears in the [My Computer] 
folder.
SCN1SCN2
DIGITAL
V. O U TDC IN
3V
ACCESS
USB MODE
SELECTSETMENUMENU SETPictBridge(PTP)PC
PLEASE SELECT
THE USB MODE
VQT0V10ENG.book  75 ページ  ２００５年１２月２７日　火曜日　午後８時３４分 
						

							Connecting to other equipment
76VQT0V10
 If you are connecting the camera to a PC for the first time, the required driver is 
installed automatically so that the camera 
can be recognized by Windows Plug and 
Play. The drive then appears on the 
[My Computer] folder.
[Macintosh]
The drive is displayed on the screen.
 The drive is displayed as [LUMIX] when  you connect the camera with no card 
inserted.
 The drive is displayed as [NO_NAME] or  [Untitled] when you connect the camera 
with a card inserted.
∫ Folder Composition
Folders are displayed as shown in the 
following illustration.
1 Folder number
2 File number
3 JPG: pictures
MOV: motion pictures
The items in each folder are as follows.  The data for up to 999 pictures recorded 
by the camera can be included in 1 folder. 
If the number of pictures exceeds 999, 
another folder is created.
 To reset the file number or the folder 
number, select [NO.RESET] in the 
[SETUP] menu. (P21)
∫ Conditions under which a different 
folder number is used
In the following cases, the picture is not 
recorded in the same folder as the 
previously recorded picture. It is recorded 
in a folder with a new number. 
1 When the folder just recorded to contains 
a picture file with the number 999 in it 
(example: P1000999.JPG).
2 When the card just recorded to contains, 
for example, a folder with the number 
100 (100_PANA) in it and that card is 
removed and replaced with a card that 
has a folder with the number 100 in it 
recorded by a camera from a different 
maker (100XXXXX, with XXXXX being 
the name of the maker) and then a 
picture is recorded.
3 When recording after selecting 
[NO.RESET] (P21) from the [SETUP] 
menu. (Pictures will be recorded to a 
new folder with a number sequential to 
the folder recorded to immediately 
before. By using [NO.RESET] on a card 
that does not contain  folders or pictures, 
such as one just formatted, the folder 
number can be reset to 100.)
∫ PictBridge (PTP) setting
Even if you set [USB MODE] to 
[PictBridge (PTP)], you can connect to your 
PC if the OS is Windows XP Home Edition/
Professional or Mac OS X.
 Pictures can only be read on the camera.  They cannot be written to a card or 
deleted.
 When there are 1000 or more pictures on  a card, the pictures may not be imported.
DCIM Folders from [100_PANA] to 
[999_PANA]
100_PANA 
to 
999_PANA Pictures/motion pictures
MISC Files on which the DPOF  print settings are recorded
100_PANA
101_PANA
999_PANA
DCIM
MISC
P1000001.JPG
P1000002.JPG
P1000999.JPG
100_PANA
≥
Built-in memory
≥ SD Memory Card
≥ MultiMediaCard
1
23
VQT0V10ENG.book  76 ページ  ２００５年１２月２７日　火曜日　午後８時３４分 
						

							Connecting to other equipment
77VQT0V10
 Do not use any other USB connection cables except the supplied one.
 Do not disconnect the USB connection 
cable while [ACCESS] is displayed.
 If battery power is exhausted while the  camera and the PC are communicating, 
the recorded data may be damaged. Use 
batteries with sufficient battery power 
(P13) or the AC adaptor (DMW-AC6; 
optional) when you connect the camera to 
the PC.
 If the remaining battery power becomes 
low while the camera and the PC are 
communicating, the status indicator blinks 
and the alarm beeps. In this case, stop 
the communication at once on the PC.
 When connecting the camera to a  Windows 2000 OS PC with the USB 
connection cable, do not replace the 
card while the camera and the PC are 
connected. The information on the card 
may be damaged. Disconnect the USB 
connection cable before replacing the 
card.
 For information about this, refer to the  separate operating instructions for PC 
connection.
 Read the operating instructions for the  PC.
 If a card is not inserted when the camera 
is connected to the PC, you can edit or 
access the pictures on the built-in 
memory. If a card is inserted, you can edit 
or access the pictures on it.
 You cannot switch between the built-in  memory and the card while the camera is 
connected to the PC. When you want to 
switch between the built-in memory and 
the card, disconnect the USB connection 
cable, insert (or remove) the card and 
then connect the USB connection cable to 
the PC again.Printing the Pictures
By connecting the camera directly to a 
printer supporting PictBridge via the USB 
connection cable (supplied), you can select 
the pictures to print and start printing on the 
camera’s screen.
Set print settings such as the print quality 
on the printer beforehand. (Read the printer 
operating instructions.)
A : USB connection cable (supplied)
B : AC adaptor (DMW-AC6; optional)
 It may take time to print some pictures.  Use batteries with sufficient battery power 
(P13) or the AC adaptor (DMW-AC6; 
optional) when you connect to a printer.
 Turn the camera off before inserting or  removing the cable for the AC adaptor 
(DMW-AC6; optional).
1 Turn on the camera and the 
printer.
2Connect the camera to a printer 
via the USB connection cable  A 
(supplied).
SCN1SCN2
DIGITAL
V. O U TDC IN
3V
VQT0V10ENG.book  77 ページ  ２００５年１２月２７日　火曜日　午後８時３４分 
						

							Connecting to other equipment
78VQT0V10
 Connect the USB connection cable with the [ ] mark facing the [ 1] mark on 
the [DIGITAL] socket.
 Hold the USB connection cable at  C 
and insert straight in or take straight 
out.
3 Press  4 to select [PictBridge 
(PTP)] and then press
[MENU/SET].
 If you set [USB MODE] in the [SETUP] 
menu to [PictBridge (PTP)] in advance, 
it is not necessary to set this every time 
you connect to a PC. (P22)
 Do not use any other USB connection cables except the supplied one.
 If a card is not inserted when the camera  is connected to the PC, you can edit or 
access the picture data on the built-in 
memory. If a card is inserted, you can edit 
or access the picture data on it.
 You cannot switch between the built-in  memory and the card while the camera is 
connected to the printer. When you want 
to switch between the built-in memory and 
the card, disconnect the USB connection 
cable, insert (or remove) the card and 
then connect the USB connection cable to 
the printer again.
 To print the age in [BABY1]/[BABY2]  (P53) in scene mode, use the software 
[LUMIX Simple Viewer] in the CD-ROM 
(supplied) and print from the PC. For 
information about this, refer to the 
separate operating instructions for PC 
connection.  To find out more about PictBridge 
compliant printers, contact your local 
dealer.
∫ Single picture
1Press  3 to select 
[SINGLE PICTURE] and then 
press  [MENU/SET].
2Press  21 to select the picture 
and then press 4.
 The message disappears in about 
2 seconds.
3 Press  3 to select [PRINT START] 
and then press  [MENU/SET].
 Press [MENU/SET] to cancel printing.
4Disconnect the USB connection 
cable after printing.
∫ Setting date printing, the number of 
prints, the paper size and the page 
layout
Select and set each item in step 3.
USB MODE
SELECTSETMENU
PC
PLEASE SELECT
THE USB MODE
PictBridge(PTP)
MENUSETSELECTSET
DPOF PICTURESINGLE PICTURE
PictBridge
MENUMENU SET
PLEASE SELECT
THE PICTURE TO PRINT
PictBridge
1/3100 _
0001
EXIT
SELECTPRINTMENU
MENU
SET


µOFF
SINGLE PICTURE
NUM. OF PRINTS
1PRINT WITH DATE
PAPER SIZEPAGE LAYOUTSELECTCANCELSETMENU
PRINT START
VQT0V10ENG.book  78 ページ  ２００５年１２月２７日　火曜日　午後８時３４分 
						

							Connecting to other equipment
79VQT0V10
 Items not supported by the printer are displayed in gray and cannot be selected.
 When you want to print pictures in a paper  size or a layout which is not supported by 
the camera, set [PAPER SIZE] or 
[PAGE LAYOUT] to [ ] and then set the 
paper size or the layout on the printer. (For 
details, refer to the operating instructions 
of the printer.)
[PRINT WITH DATE]
 If the printer does not support date  printing, the date cannot be printed on the 
picture.
 [NUM. OF PRINTS] Set the number of prints.
[PAPER SIZE] (Paper sizes that can be set with this unit)
The paper sizes are displayed on pages 
1/2 and 2/2. Press  4 to select.
¢These items cannot be displayed when  the printer does not support the paper 
sizes. [PAGE LAYOUT]
(Layouts that can be set with this unit)
 An item cannot be selected if the printer  does not support the page layout.
∫ DPOF picture
 Set the DPOF print setting on the 
camera in advance. (P68)
1 Press  4 to select 
[DPOF PICTURE] and then press 
[MENU/SET].
2 Press  3 to select [PRINT START] 
and then press [MENU/SET].
 You cannot select [PRINT START] 
when the DPOF print setting is not set. 
Select [DPOF SET] and then set the 
DPOF print setting. (P68)
 Press [MENU/SET] to cancel printing.
3 Disconnect the USB connection 
cable after printing.
Settings on the printer are 
prioritized.
OFF Date is not printed.
ON Date is printed.
1/2 Settings on the printer are 
prioritized.
L/3.5qk5 q
89 mmk127 mm
2L/5qk7q 127 mmk178 mm
POSTCARD 100 mm
k148 mm
A4 210 mm
k297 mm
2/2¢
CARD SIZE54 mmk85.6 mm
10k15cm 100 mmk150 mm
4 q
k6q 101.6 mmk152.4 mm
8 q
k10q 203.2 mmk254 mm
LETTER 216 mm
k279.4 mm
Settings on the printer are 
prioritized.
1 page with no frame is printed.
1 page with a frame is printed.
2 pages are printed.
4 pages are printed.
SELECTSET
DPOF PICTURESINGLE PICTURE
PictBridge
MENUMENU
SET
MENUMENU SETDPOF SET PAPER SIZEPAGE LAYOUT
PRINT STARTDPOF
SELECTCANCELSETMENU
VQT0V10ENG.book  79 ページ  ２００５年１２月２７日　火曜日　午後８時３４分 
						

							Connecting to other equipment
80VQT0V10
∫Setting the date printing with the 
DPOF print in advance
We recommend setting DPOF date printing 
with [DPOF PRINT] (P70) in advance when 
the printer supports it. If you select 
[DPOF PICTURE], printing starts and the 
recording date is printed.
∫ Layout printing
 When printing a picture several times 
on 1 sheet of paper
For example, if you want to print a picture 
4 times on 1 sheet of paper, set 
[PAGE LAYOUT] to [ ] and then set 
[NUM. OF PRINTS] to 4.
 When printing different pictures on 
1 sheet of paper (only in DPOF 
printing)
For example, if you want to print 4 different 
pictures on 1 sheet of paper, set 
[PAGE LAYOUT] to [ ] and then set 
[COUNT] in [DPOF PRINT] (P68) to 1 for 
each of the 4 pictures.
 Do not disconnect the USB connection cable when the cable disconnection 
warning icon [ ] is displayed. 
(Depending on the printer, the icon may 
not be displayed.)
 If the remaining battery power becomes 
low while the camera and the printer are 
connected, the status indicator blinks and 
the alarm beeps. If this happens during 
printing, press [MENU/SET] and stop 
printing at once. If not printing, disconnect 
the USB connection cable.
 The camera is receiving an error message  from the printer when the [ ¥] indication 
lights orange during printing. After 
finishing printing, make sure there are no 
problems with the printer.
 If the total number of DPOF prints or the 
number of DPOF pictures printed is high, 
pictures may be printed several times. The 
remaining number of prints indicated may  differ from the number set. This is not a 
malfunction.
 With date printing, the setting on the  printer may take priority over the setting 
on the camera. Check the date print 
setting on the printer also.
VQT0V10ENG.book  80 ページ  ２００５年１２月２７日　火曜日　午後８時３４分