Panasonic Digital Camera Dmc Lc70 Operating Instructions

							Playback (advanced)
91
Trimming the Pictures
Preparation
 Set the mode dial to [ ]. (P29)
1Select [TRIMMING].
2Select the picture to trim.
3Enlarge or decrease the picture.
PLAY2/2SETUP
TRIMMING RESIZE
FORMAT
EXITSET SELECTMENU
WBWB
SET SELECT
EXITMENU
TRIMMING1600
100-0001
1/19
WBWB
TRIMMING
ZOOM
1600
1/19
EXITMENU
100_
0001
WT
DMC-LC80.book  91 ページ  ２００４年６月１５日　火曜日　午後５時４９分 
						

							Playback (advanced)
92
4Shift the picture and press the 
shutter button fully to set.
5Select [YES] or [NO] and set it.
 When you select [YES], the picture 
is overwritten.
 When the original picture is 
protected, you cannot overwrite the 
trimmed picture.
 Close the menu by pressing the 
[MENU] button 2 times after 
finishing the trimming.
¬Suggestions/Tips ¬
 The following pictures cannot be 
trimmed.
– Pictures smaller than 640k480 
pixels
– Pictures recorded after setting the 
picture size to [HDTV]
– Motion images
– Flip animation (DMC-LC80/
DMC-LC70)
–
Pictures with audio (DMC-LC80/
DMC-LC70)
– Rotated pictures (You can trim them 
if you rotate them back.)
 It may not be possible to trim pictures 
recorded with other equipment.
 The picture size of the trimmed 
pictures may become smaller than that 
of the original one depending on the 
cut size.
 The picture quality of the trimmed 
picture may be deteriorated.
TRIMMING
TRIM:SHUTTER
1600
1/19
EXITMENU
100_
0001
ZOOM
WB
DELETE ORIGINAL
PICTURE?
YESNO
TRIMMING
SET SELECTCANCELMENU
WBWB
DMC-LC80.book  92 ページ  ２００４年６月１５日　火曜日　午後５時４９分 
						

							Playback (advanced)
93
Formatting the Card
Preparation
 Set the mode dial to [ ]. (P29)
1Select [FORMAT].
2Select [YES] to format.
¬Suggestions/Tips ¬
 Usually, it is not necessary to format 
the card (initializing). Format the card 
when the message [MEMORY CARD 
ERROR] appears.
 If the card has been formatted by a PC 
or other equipment, format the card on 
the camera again.
 After formatting, recorded pictures and 
any other data cannot be recovered.
 If the card is formatted all images 
and data will be permanently 
erased. They cannot be reclaimed. 
If any important pictures are on the 
card, please copy them to your PC 
before proceeding.
 During formatting, do not turn the 
camera off.
 Use sufficiently charged batteries 
(P13) or AC adaptor (optional, 
DMW-AC1).
 When the SD Memory Card 
Write-Protect switch is slid to [LOCK], 
you cannot format the card.
 If the card cannot be formatted, 
consult your nearest servicenter.
PLAY2/2SETUP
TRIMMING RESIZE
FORMAT
EXITSET SELECTMENU
WBWB
DELETE ALL DATA
ON THE MEMORY CARD?
YESNO
FORMAT
SET SELECT
WBWBFor USA assistance, please call: 1-800-272-7033 
or send e-mail to : [email protected]
For Canadian assistance, please call:
1-800-561-5505 or visit us at www.panasonic.ca
DMC-LC80.book  93 ページ  ２００４年６月１５日　火曜日　午後５時４９分 
						

							Playback (advanced)
94
Playing Back Pictures with a TV Screen
ªPlaying back pictures with AV cable (supplied with DMC-LC80/DMC-LC70) 
or video cable (supplied with DMC-LC50).
 Turn the camera and the TV off.
 DMC-LC80/DMC-LC70 is illustrated 
below as an example.
1 AV cable (DMC-LC80/DMC-LC70)
Video cable (DMC-LC50)
1Connect the AV cable (supplied 
with DMC-LC80/DMC-LC70) to the 
[AV OUT] socket of the camera 
(DMC-LC80/DMC-LC70). Connect 
the video cable (supplied with 
DMC-LC50) to the [V.OUT] socket 
of the camera (DMC-LC50).
 Align the 2 mark on the AV cable 
(video cable) and the 1 mark on the 
[AV OUT (V.OUT)] socket.
2Connect the AV cable to the video 
input and the audio input sockets 
of the TV (DMC-LC80/DMC-LC70). 
Connect the video cable to video 
input socket of the TV 
(DMC-LC50).
A  Yellow: to the video input socket
B  White: to the audio input socket 
(DMC-LC80/DMC-LC70)
3Turn the TV on and select external 
input.
4Turn the camera on and then set 
the mode dial to playback mode 
[].
ªViewing pictures in other 
countries
When setting [VIDEO OUT] on the 
menu, you can view pictures on a TV in 
other countries (regions) which use the 
NTSC or PAL system.
 Even if you set menu selection for 
[VIDEO OUT] to [PAL], the output signal 
is still NTSC in the recording mode.
ªPlayback pictures on TV with an 
SD Memory Card slot
An SD Memory Card can be played back 
on TVs with an SD Memory Card slot.
If you play back pictures recorded using 
[HDTV] mode on a High-Definition TV, 
(HDTV has 16:9 aspect) the picture 
quality will be higher.
¬
Suggestions/Tips ¬
 Do not use any other AV  (video) 
cables except the supplied one.
 Read the TV operating instructions 
too.
1
A
B
DMC-LC80.book  94 ページ  ２００４年６月１５日　火曜日　午後５時４９分 
						

							Playback (advanced)
95
Before Connecting with USB Connection 
Cable
Select the USB communication system according to the OS of your PC or your 
printer before connecting them to the camera with the USB connection cable 
(supplied).
Set the items on [USB MODE] in the [SETUP] menu. (P25)
1Select [USB MODE].
(In the recording mode)2Select [Mass Storage] or [PTP].
REC SETUP2/
3
USB MODE
NO.RESET
RESET
CLOCK SET
EXITSET SELECTMENU
WB
WBWB
USB
SET SELECT
Mass StoragePTP
USB MODE
USB
Direct-PrintPictBridge
WBWB
USB modePC to be connectedPrinter to be 
connected
Mass Storage
(USB Direct-Print)Windows
® XP Home Edition, 
Windows XP Professional, 
Windows 2000 Professional, 
Windows Me, Windows 98/98 SE or 
Mac OS X (10.1 or above), 
Mac OS 9.xPrinters supporting 
USB 
DIRECT-PRINT.
PTP
(PictBridge)Windows XP Home Edition, 
Windows XP Professional or 
Mac OS XPrinters supporting 
PictBridge.
DMC-LC80.book  95 ページ  ２００４年６月１５日　火曜日　午後５時４９分 
						

							Playback (advanced)
96
ªWhen using Windows 98/98 SE
 When using Windows 98/98 SE, install the USB driver before connecting. (When 
using Windows Me/2000/XP, Mac OS 9.x and Mac OS X, you do not have to install 
the USB driver.)
ªWhen using Windows 2000 Professional, Windows Me, 
Windows 98/98 SE or Mac OS 9.x
The [PTP] (PictBridge) setting is not supported on the following OS’s: Windows 
2000 Professional, Windows Me, Windows 98/98 SE or Mac OS 9.x.
Please refer to the following information.
 When connecting the camera to a PC, do not set [USB MODE] to [PTP].
(When the camera is shipped, [Mass Storage] is selected.)
 When connecting to a PC which includes the 
above-mentioned OS and setting the [USB MODE] to [PTP], 
the messages shown on the right appear on the LCD 
monitor of the camera.
The following messages appear for each OS on the display of the PC. Select 
[Cancel] to close the window and disconnect the PC.
PTP
USB MODE
OSMessage
Windows 2000 Professional [Welcome to the Found New Hardware 
Wizard]
Windows Me
Windows 98/98 SE[New Hardware Found]>
[Add New Hardware Wizard]
(When you connect to the PC more than 
2 times, only [Add New Hardware Wizard] 
appears.)
Mac OS 9.x [Software needed for the USB device 
“DMC-LC80, DMC-LC70 or DMC-LC50” is not 
available. Would you like to look for the 
software on the Internet?]
DMC-LC80.book  96 ページ  ２００４年６月１５日　火曜日　午後５時４９分 
						

							Playback (advanced)
97
Connecting to a PC (Mass Storage)
 DMC-LC80/DMC-LC70 is illustrated 
below as an example.
A AC adaptor (optional, DMW-AC1)
B USB connection cable
1Turn the camera on and then set 
[USB MODE] to [Mass Storage]. 
(P95)
2Connect the camera to a PC via 
the USB connection cable 
(supplied).
 Align the 2 mark on the USB 
connection cable and the 1 mark on 
the [DIGITAL] socket.[Windows]
The drive appears on the 
[My Computer] folder.
 If it is the first time you are 
connecting the camera to a PC, the 
required driver is installed 
automatically so that the camera 
can be recognized by the Windows 
Plug and Play, then it appears on 
the [My Computer] folder.
[Macintosh]
The drive is shown on the screen.
¬Suggestions/Tips ¬
 The status indicator lights during 
communication.
 When connecting to a PC, we 
recommend using the AC adaptor 
(optional, DMW-AC1) as the power 
source.
 If the remaining battery power 
becomes low during communication, 
the power indicator blinks and the 
alarm beeps. In this case, stop the 
communication, because the data may 
be destroyed. Then turn the camera 
off and use the following power 
source.
 New batteries
 Charged batteries
 AC adaptor (optional, DMW-AC1)
 Do not use any other USB connection 
cables except the supplied one.
A
B
DMC-LC80.book  97 ページ  ２００４年６月１５日　火曜日　午後５時４９分 
						

							Playback (advanced)
98
Connecting to a PC (PTP)
Do not follow the setting below on the OS except for Windows XP and Mac OS X.
 DMC-LC80/DMC-LC70 is illustrated 
below as an example.
A AC adaptor (optional, DMW-AC1)
B USB connection cable
1Turn the camera on and then set 
[USB MODE] to [PTP]. (P95)
2Connect the camera to a PC via 
the USB connection cable 
(supplied).
 Align the 2 mark on the USB 
connection cable and the 1 mark on 
the [DIGITAL] socket.[Windows]
The camera icon appears on the 
[My Computer] folder.
 If it is the first time you are 
connecting the camera to a PC, the 
required driver is installed 
automatically so that the camera 
can be recognized by the Windows 
Plug and Play, then the camera 
icon appears on the [My Computer] 
folder.
[Macintosh]
You can read pictures with image 
capture or iPhoto.
A
B
DMC-LC80.book  98 ページ  ２００４年６月１５日　火曜日　午後５時４９分 
						

							Playback (advanced)
99
¬Suggestions/Tips ¬
 Refer to P96 when connecting to the OS except for Windows XP and Mac OS X 
when setting [USB MODE] to [PTP].
 The status indicator lights during communication.
 When connecting to a PC, we recommend using the AC adaptor (optional, 
DMW-AC1) as the power source.
 If the remaining battery power becomes low during communication, the power 
indicator blinks and the alarm beeps. In this case, stop the communication, 
because the data may be destroyed. Then turn the camera off and use the 
following power source.
 New batteries
 Charged batteries
 AC adaptor (optional, DMW-AC1)
 It may take time to display the communication screen depending on the PC.
 You can only load pictures from the camera and cannot write them on the card or 
delete them.
 Do not use any other USB connection cables except the supplied one.
 When there are 1000 or more pictures on the card, the pictures may not be 
imported.
 When the PC recovers from the standby mode while connecting it to a camera 
with USB connection cables, they may not properly communicate with each other.
DMC-LC80.book  99 ページ  ２００４年６月１５日　火曜日　午後５時４９分 
						

							Playback (advanced)
100
Connecting to a Printer
By connecting the camera directly to a printer supporting PictBridge or USB 
DIRECT-PRINT via the USB connection cable (supplied), you can select the 
pictures to be printed or start printing.
 DMC-LC80/DMC-LC70 is illustrated 
below as an example.
A AC adaptor (optional, DMW-AC1)
B USB connection cable
1Turn the camera on and then set 
the [USB MODE] to [PTP] 
(PictBridge) or [Mass Storage] 
(USB DIRECT-PRINT). (P95)
2Turn on a printer.
3Connect the camera to the printer 
via the USB connection cable 
(supplied).
 Align the 2 mark on the USB 
connection cable and the 1 mark on 
the [DIGITAL] socket.
¬Suggestions/Tips ¬
 Ask the manufacturer of the printer 
about the corresponding models. 
(Read the printer operating 
instructions too.)
 If the remaining battery power 
becomes low during communication, 
the power indicator blinks and the 
alarm beeps. In this case, stop the 
communication, because the data may 
be destroyed. Then turn the camera 
off and use the following power 
source.
 New batteries
 Charged batteries
 AC adaptor (optional, DMW-AC1)
 When connecting to a printer, we 
recommend using the AC adaptor 
(optional, DMW-AC1) as the power 
source.
 Set the paper size and print quality 
with the printer. (Read the printer 
operating instructions.)
 Disconnect the USB connection cable 
after printing.
 Do not use any other USB connection 
cables except the supplied one.
A
B
DMC-LC80.book  100 ページ  ２００４年６月１５日　火曜日　午後５時４９分