Panasonic Digital Camera Dmc Lc43 Operating Instructions

							Technical use
81
USB DIRECT-PRINT
By connecting the camera to a printer corresponding to USB DIRECT-PRINT via the 
supplied USB connection cable, it is possible to print directly. 
(Please ask the manufacturer of the printer about the corresponding models)
(Read the printer operating instructions too)
1Insert the Memory Card into the camera, and turn the power switch to 
[ON].
2Turn on the printer.
3Connect the camera to the printer via the supplied USB cable 1.
 When connecting to a printer, use the batteries which the remaining power is 
enough or AC adaptor 2 (optional, DMW-AC1).
 Disconnect the USB connection cable and DC cable after printing.
A/V OUT
DC IN
USB
1
21 2
3
KC93-PP.book  81 ページ  ２００３年３月１９日　水曜日　午後２時１１分 
						

							Technical use
82
USB DIRECT-PRINT (Single Picture)
[Preparation]
 Connect the camera to a printer. (P81)
1Only when DPOF is already set, press 
2 to select [SINGLE PICTURE], and 
then press the 4/[REVIEW/SET] 
button.
 When DPOF is not set, this screen is 
skipped.
2Press 2/1 to select the picture to be 
printed, and then press the 
4
/[REVIEW/SET] button.
 The message “PLEASE SELECT THE 
PICTURE TO PRINT” is displayed for 
2 seconds.
3Press 3, and press 2/1 to set the 
number of sheets, and then press the 
4/[REVIEW/SET] button.
4Press 2 to select [YES].
 The message “PLS CHECK THE 
PRINTER START PRINTING ?” is 
displayed.
5Press the 4/[REVIEW/SET] button.
 Printing starts.
 Press the [MENU] button, and you can stop 
printing.
1
1
2
3,4
5
2304
2304
SINGLE
PICTURE
DIRECT PRINT
DIRECT PRINT
SELECT
SELECTSET
PRINT
DIRECT PRINT
THE PICTURE TO PRINT
PLS CHECK THE PRINTER
START PRINTING ?
COUNT1
YES
NO
SELECTSETPRINTSET
DIRECT PRINT
1 / 8
CANCEL
NOW PRINTINGREMAIN 8
KC93-PP.book  82 ページ  ２００３年３月１９日　水曜日　午後２時１１分 
						

							Technical use
83
USB DIRECT-PRINT (DPOF)
[Preparation]
 Connect the camera to a printer. (P81)
 Write the print information to the card 
(DPOF setting). (P61)
1Press 2/1 to select [DPOF].
 Press the [MENU] button, and you can 
change the DPOF setting. (P61)
2Press the 4/[REVIEW/SET] button.
 The message “PLS CHECK THE 
PRINTER START PRINTING ?” is 
displayed.
3Press 2 to select [YES], and then 
press the 4
/[REVIEW/SET] button.
 Printing starts.
 Press the [MENU] button, and you can stop 
printing.
 When the number of total images is more 
than 255, the number of remaining images 
will be displayed as “----”.
2 1
3
2304
DIRECT PRINT
DIRECT PRINT SINGLE
PICTURE
SELECTSET
SELECTSET
PLS CHECK THE PRINTER
START PRINTING ?
YES
NO
DIRECT PRINT
NOW PRINTINGREMAIN 8
CANCEL
KC93-PP.book  83 ページ  ２００３年３月１９日　水曜日　午後２時１１分 
						

							Technical use
84
Using the AC Adaptor
If you use an AC adaptor (optional, DMW-AC1), you can use the camera without 
worrying about battery discharge.
[Preparation]
 Check that the power switch is set to [OFF] and the lens is stored.
1Connect the AC power plug to the AC outlet.
2Open the terminal door.
3Connect the AC adaptor to the DC IN socket.
 Do not use the AC adaptor other than the optional one (DMW-AC1).
 The camera becomes warm during use, however, this is not a malfunction.
 The battery cannot be charged in the camera with the AC adaptor connected.
 When disconnecting/connecting the AC adaptor with the power switch turned 
on using the batteries, the data in the card may be destroyed or operation may 
be impossible. Be sure to disconnect/connect the AC adaptor after turning the 
power switch to off. THE SOCKET OUTLET SHALL BE 
INSTALLED NEAR THE EQUIPMENT 
AND SHALL BE EASILY ACCESSIBLE.
A/V OUT
DC IN
USB
KC93-PP.book  84 ページ  ２００３年３月１９日　水曜日　午後２時１１分 
						

							Technical use
85
After Use
After using the camera and following the 
steps below, it is recommended to place it in 
the optional soft case for protection.
1Turn the power switch to  [OFF]. (P19)
2Eject the card. (P17)
3Remove the batteries.
 If you will not be using the camera for a long time, remove the batteries. (When 
you insert the batteries again, set the date/time)
2
3
OFF ON1
KC93-PP.book  85 ページ  ２００３年３月１９日　水曜日　午後２時１１分 
						

							Others
86
Others
The Menu Items
REC mode menu
1W.BALANCE (P49)2PICT.SIZE (P37)
3QUALITY (P38)4SPOT MODE (P43)
5SENSITIVITY (P51)6AUDIO REC. (P36)
7D.ZOOM (P32)8COL.EFFECT (P43)
9PICT.ADJ. (P48)
10MONITOR (P72)
11AUTO REVIEW (P73)12POWER SAVE (P75)13ECONOMY (P76)
14BEEP (P74)15NO.RESET (P77)
16RESET (P78)17CLOCK SET (P25)
18LANGUAGE
1
2
3
4
SELECT SETEXITMENUSELECT SETEXITMENU
2304PICT.SIZEQUALITYSPOT MODE
REC1/3
W.BALANCE 
SETUP
1617
15
13
10
11
REC2/3
AUDIO REC.
SENSITIVITY
SETUP
SELECT SETEXITMENU
SELECT SETEXITMENU
REC3/3SETUP
PICT.ADJ.VIVIDSTANDARD STANDARD
SELECT SETEXITMENU
REC
SETUP   1/3
AUTO REVIEW
ECONOMY12POWER SAVE
MONITOR
SELECT SETEXITMENU
SETUP   2/3REC
RESETCLOCK SET
NO.RESET
18
SETUP   3/3REC
D.ZOOM
COL. EFFECT
5
6
7
8
9
BEEP14
ENGLANGUAGE
ECO
50 100 200
KC93-PP.book  86 ページ  ２００３年３月１９日　水曜日　午後２時１１分 
						

							Others
87
Simple mode menu
 For items without number, refer to those with 
the same name.
19
PICT.MODE (P28)
Playback mode menu
 For items without number, refer to those with 
the same name.
20
PROTECT (P64)21DPOF PRINT (P61)22SLIDE SHOW (P65)
23AUDIO DUB. (P67)24RESIZE (P68)
25TRIMMING (P69)26FORMAT (P71)
27VIDEO OUT (P79)
19
OFFBEEP
ONAUTO REVIEW
PICT.MODE
CLOCK SET
ENLARGE4k6/10k15cm
SELECT SET EXITMENU
202122
26
2324
25                            
27 
SETUPPLAY2/2
SELECT SETEXITMENU
PLAYSETUP   2/2
SELECT SETEXITMENU
PLAY1/2
PROTECTDPOF PRINT
SLIDE SHOW
AUDIO DUB.
SETUP
TRIMMING
RESIZESELECT SETEXITMENU
PLAY
SETUP   1/2
SELECT SETEXITMENU
FORMAT
MONITORPOWER SAVE
BEEP
CLOCK SET
NTSC
ENGLANGUAGE
VIDEO OUT
2MIN.
KC93-PP.book  87 ページ  ２００３年３月１９日　水曜日　午後２時１１分 
						

							Others
88
Cautions for Use
ª Cautions for Use
Keep the digital camera away from 
magnetized equipment (such as a 
microwave oven, TV, video game 
equipment, etc.).
 If you use the digital camera on or 
near a TV, images and sounds may be 
disturbed due to electromagnetic wave 
radiation.
 Do not use the digital camera near a 
cell phone because doing so may 
cause noise to adversely affect the 
images and sounds.
 Recorded data may be damaged, or 
images may be distorted by strong 
magnetic fields created by speakers or 
large motors.
 Electromagnetic wave radiation 
generated by a microprocessor may 
adversely affect the digital camera, 
causing the disturbance of images and 
sounds.
 If the digital camera is affected by 
magnetically charged equipment and 
does not function properly, turn the 
camera off and detach the batteries 
and then connect the batteries again. 
Thereafter, turn the camera on.
Do not use the digital camera near 
radio transmitters or high-voltage 
lines.
 If you record near radio transmitters or 
high-voltage lines, recorded images or 
sounds may be adversely affected.
Do not spray insecticides or 
volatile chemicals onto the digital 
camera.
 If the digital camera is sprayed with 
such chemicals, the camera body may 
be damaged and the surface finish 
may peel off.
 Do not keep rubber or plastic products 
in contact with the digital camera for a 
long period of time.
When you use the digital camera 
on a beach or similar place, do not 
let sand or fine dust get into the 
camera.
 Sand or dust may damage the digital 
camera or card. (Care should be taken 
when inserting and removing the card)
When you use your digital camera 
on a rainy or snowy day or on a 
beach, make sure that no water 
enters the digital camera.
 Water may cause the digital camera or 
card to malfunction. (Irreparable 
damage may occur)
 If sea water splashes onto the digital 
camera, wet a soft cloth with tap 
water, wring it well, and use it to wipe 
the camera body carefully. Then, wipe 
it again thoroughly with a soft dry 
cloth.
Do not use the digital camera for 
surveillance purposes or other 
business use.
 If you use the digital camera for a long 
period of time, the internal 
temperature increases and, 
consequently, this may cause 
malfunction.
 The digital camera is not intended for 
business use.
KC93-PP.book  88 ページ  ２００３年３月１９日　水曜日　午後２時１１分 
						

							Others
89 Do not use benzine, thinner or 
alcohol for cleaning the digital 
camera.
 The camera body may be deformed 
and the surface finish may peel off.
 Before cleaning the camera, detach 
the batteries.
 Wipe the digital camera with a soft, dry 
cloth. To remove stubborn stains, wipe 
with a cloth that is soaked in a 
detergent diluted with water and 
afterward finish wiping with a dry cloth.
 For storing or transporting the digital 
camera, place it in a bag or case lined 
with soft pads to prevent the coating 
on the camera body from being worn.
After use, be sure to take the card 
out, and detach the batteries.
 If the batteries are left on the digital 
camera for a long time, the voltage 
drops excessively, and the batteries 
will not function even after they are 
recharged.
Be sure to remove the batteries 
after use.
Be sure to remove the batteries from the 
digital camera. (If they are left attached 
to the digital camera, a minute amount 
of current is consumed even when the 
digital camera power is off) If the 
batteries are left attached to the digital 
camera for a long time, discharge takes 
place. The batteries may become 
unusable even after they are charged.
Dispose of unusable batteries. The batteries have a limited life.
 Do not throw the batteries into fire 
because it may cause an explosion.
Always keep the terminals of the 
batteries clean.
Prevent the terminals from getting 
clogged with dirt, dust, or other 
substances.
If you drop the battery accidentally, 
check to see if the battery body and 
terminals are deformed. Attaching a 
deformed battery to the digital camera 
may damage the camera.
A nickel metal hydride battery that is recyclable powers the 
product you have purchased. Please call 1-800-8-BATTERY for 
information on how to recycle this battery.RBRC
Ni-MH
TM
KC93-PP.book  89 ページ  ２００３年３月１９日　水曜日　午後２時１１分 
						

							Others
90 ª Condensation
When condensation has taken 
place:
Set the power switch to [OFF] and 
leave the digital camera in this 
condition for about 1 hour. When 
the camera becomes close to the 
ambient temperature, the fog 
disappears naturally.
ª Cautions for Storage
Before storing the digital camera, take 
the card out and detach the batteries.
Store all the components in a dry place 
with a relatively stable temperature.
(Recommended temperature:
59 oF to 77 oF (15oC to 25oC), 
Recommended humidity: 40 to 60%)
Digital camera Wrap it with a soft cloth to prevent dust 
from getting into the camera.
 Do not leave the camera in places that 
expose it to high temperature.
Batteries Do not leave the camera and the 
battery in places where the 
temperature is too high, such as inside 
the car during the summer.
 Extremely high or low temperatures 
will shorten the life of batteries.
 If the batteries are kept in smoky or 
dusty places, the terminals may rust 
and cause malfunctions.
 Do not allow the battery terminals to 
come in contact with metal objects 
(such as necklaces, hairpins, etc.). 
This can result in a short circuit or heat 
generation, and if you touch the 
battery in this condition, you may be 
badly burned.
Card 
 When the card is being read, do not 
remove the card, turn off the power, or 
subject it to vibration or impact.
 Do not leave the card in places where 
there is high temperature or direct 
sunlight, or where electromagnetic 
waves or static electricity are easily 
generated.
 Do not bend or drop the card. The 
card or the recorded content may be 
damaged.
 After use, be sure to remove the card 
from the digital camera.
 Do not touch the terminals on the back 
of the card with your fingers. Do not 
allow dirt, dust or water to enter it.
ª LCD monitor
LCD monitor In a place with drastic temperature 
changes, condensation may form on 
the LCD monitor. Wipe it with soft dry 
cloth. If the digital camera is extremely cold 
when you turn the power on, the 
image on the LCD monitor is slightly 
darker than usual at first. However, as 
the internal temperature increases, it 
goes back to the normal brightness.
KC93-PP.book  90 ページ  ２００３年３月１９日　水曜日　午後２時１１分