Panasonic Digital Camera Dmc Gh1K Operating Instructions

							21VQT2A61
Preparation
Charging the Battery
∫About batteries that you can use with this unit
The battery that can be used with this unit is DMW-BLB13PP.
 Use the dedicated charger and battery.
 This unit has a function that can distinguish useable batteries. Exclusive batteries  
(DMW-BLB13PP) are supported by this function. (Conventional batteries not supported 
by this function cannot be used)
 The battery is not charged when the camera is shipped. Charge the battery before use.
 Charge the battery with the charger indoors.
 Charge the battery in a temperature between 10 oC to 35 oC (50 oF to 95 oF). (The battery 
temperature should also be the same.)
It has been found that counterfeit battery packs which look very similar to the 
genuine product are made available to purchase in some markets. Some of these 
battery packs are not adequately protected with internal protection to meet the 
requirements of appropriate safety standards. There is a possibility that these 
battery packs may lead to fire or explosion. Please be advised that we are not 
liable for any accident or failure occurring as a result of use of a counterfeit 
battery pack. To ensure that safe products are used we would recommend that a 
genuine Panasonic battery pack is used.
Connect the AC cable.
 The battery cannot be charged when the DC cable is 
connected to the AC adaptor.
Attach the battery paying attention to the 
direction of the battery.
Charging starts when the [CHARGE] indicator  A lights 
green.
Detach the battery after charging is 
completed.
 Charging is complete when the [CHARGE] indicator  A 
turns off.
DMC-GH1KPP-VQT2A61_eng.book  21 ページ  ２００９年４月１４日　火曜日　午後２時４５分 
						

							VQT2A6122
Preparation
∫When the [CHARGE] indicator flashesThe battery temperature is excessively high or low. The charging time will be longer than 
normal. Also, charging may not be completed.
 The terminals of the charger or the battery are dirty. In this case, wipe them with a dry cloth.
NoteDo not use any other AC cables except the supplied one.
 Disconnect the charger from the power outlet after the charging is completed.
 The battery becomes warm after using it and during and after charging. The camera also 
becomes warm during use. This is not a malfunction.
 The battery will become discharged if left for a long period of time after being charged.
 The battery can be recharged even when it still has some charge le ft, but it is not 
recommended that the battery charge be frequently topped up while the battery is fully 
charged. (The battery has characteristics that will reduce its operating duration and cause the 
battery to swell up.)
 When the operating time of the camera becomes extremely short even after properly charging 
the battery, the life of the battery may have expired. Buy a new battery. 
 Do not leave any metal items (such as clips) near the contact areas of the power plug. 
Otherwise, a fire and/or electric shocks may be caused by short-circuiting or the 
resulting heat generated.
∫ Battery indication
The battery indication is displayed on the LCD monitor/Viewfinder.
[It does not appear when you use the camera with the AC adaptor
 (P25) connected.]
 The indication turns red and blinks if the remain ing battery power is exhausted. (The status 
indicator also blinks) Recharge the battery or replace it with a fully charged battery.
∫ The battery life
Recording conditions by CIPA standard
 CIPA is an abbreviation of [Camera & Imaging Products Association].
 Temperature: 23 oC (73.4 oF)/Humidity: 50% when LCD monitor is on.¢
 Using a Panasonic SD Memory Card (512 MB).
 Using the supplied battery.
 Use the 14 – 140 mm/F4.0 – 5.8 lens included in DMC-GH1K.
 Starting recording 30 seconds after the camera is turned on. (When the Optical Image 
Stabilizer function is set to [MODE1].)
 Recording once every 30 seconds  with full flash every second recording.
 Turning the camera off every 10 recordings and leaving it until the temperature of the battery 
decreases.
¢The number of recordable pictures decreases in Auto power LCD mode or Power LCD 
mode. (P35)
About the Battery (charging/number of recordable pictures)
Number of 
recordable  pictures Approx. 
300 pictures (By CIPA standard in Program AE Mode)
Recording timeApprox. 
150 min
DMC-GH1KPP-VQT2A61_eng.book  22 ページ  ２００９年４月１４日　火曜日　午後２時４５分 
						

							23VQT2A61
Preparation
The number of recordable pictures varies depending on the recording interval time. 
If the recording interval time becomes longer, the number of recordable pictures 
decreases. 
[e.g. When recording once every 2 minutes, the number of recordable pictures 
decreases to about 75.]
When using the viewfinder
Playback time when using the LCD monitor
The number of recordable pictures and playback time will vary depending on the 
operating conditions and storing condition of the battery.
Available continuous recording time when using the LCD monitor (when recording 
motion pictures)
 Recorded continuously setting the recording mode to [AVCHD] and [REC QUALITY] to [SH] 
([ ])
Available recording time is different depending on the recording intervals or 
conditions of use.¢
¢ Available recording time becomes shorter when turning the power [ON]/[OFF], start/stop of 
the recording, etc. are repeated.
∫Charging
The indicated charging time is for when the battery has been discharged completely. 
The charging time may vary depending on how the battery has been used. The charging 
time for the battery in hot/cold environments or a battery that has not been used for long 
time may be longer than normal.
When the charging has been completed successfully, the [CHARGE] indicator turns off.
Charging time and  number of recordable pictures  with the optional battery pack 
(DMW-BLB13PP) are the same as above.
Note
The battery may swell and its operating time may become shorter as the number of times it is 
charged increases. For long term battery use, we recommend you do not frequently charge the 
battery before it is exhausted.
 The performance of the battery may temporarily deteriorate and the operating time may 
become shorter in low temperature conditions (e.g. skiing/snowboarding).
Number of 
recordable 
pictures Approx. 
320 pictures (By CIPA standard in Program AE Mode)
Recording timeApprox. 
160 min
Playback time Approx. 260 min
Available continuous 
recording time
(motion picture) Approx. 120 min
Charging time
Approx. 155 min
DMC-GH1KPP-VQT2A61_eng.book  23 ページ  ２００９年４月１４日　火曜日　午後２時４５分 
						

							VQT2A6124
Preparation
Inserting/Removing the Battery
Check that this unit is turned off.
 Close the flash.
Slide the release lever in the direction of the 
arrow (OPEN side) and then open the battery 
door.
 Always use genuine Panasonic batteries 
(DMW-BLB13PP).
 If you use other batteries, we cannot guarantee the 
quality of this product.
Insert until it is locked by the lever  A being 
careful about the direction you insert it. Pull 
the lever A in the direction of the arrow to 
remove the battery.
1: Close the battery door.
2: Slide the release lever in the direction of 
the arrow (LOCK side) and then close it 
firmly.
NoteRemove the battery after use.
 Do not remove the battery while the power is on as the settings on the camera may not be 
stored properly.
 The supplied battery is designed only for the camera. Do not use it with any other equipment.
 Before removing the battery, turn the camera off, and wait until the status indicator has gone off 
completely. (Otherwise, this unit may no longer operate normally and the card itself may be 
damaged or the recorded pictures may be lost.)
DMC-GH1KPP-VQT2A61_eng.book  24 ページ  ２００９年４月１４日　火曜日　午後２時４５分 
						

							25VQT2A61
Preparation
Using the AC Adaptor
You can use the camera without worrying about battery discharge when it is connected to 
a PC or a printer if you use the DC cable to connect the camera to the battery charger/AC 
adaptor and connect the AC cable.
 Check that the camera is turned off.
 Close the flash.
Connect the AC cable.
Connect the DC cable  A.
Pull open the DC cable cover  1 and then 
connect the DC cable to the camera body using 
the same steps as “Inserting/Removing the 
Battery” (P24). Pull the DC cable through the 
opening as shown in the illustration and then 
close the battery door.
 Be careful not to catch the DC cable when 
closing the battery door.
 You cannot charge the battery if you connect the 
DC cable.
NoteDo not use any other AC cables except the supplied one.
 Do not use any other DC cables except the supplied one. If you use other DC cables, it may 
cause a malfunction.
 The camera becomes warm during use. This is not a malfunction.
 Disconnect the charger/AC adaptor and DC cable when the camera is not in use.
 It is recommended to use a fully charged battery or AC adaptor when recording motion 
pictures.
 If while recording motion pictures using the AC adaptor the power supply is cut off due to a 
power cut or if the AC adaptor is disconnected etc., the motion picture being recorded will not 
be recorded.
 The unit is in the standby condition when the AC adaptor is connected. The primary circuit is 
always “live” as long as the AC adaptor is connected to an electrical outlet.
DMC-GH1KPP-VQT2A61_eng.book  25 ページ  ２００９年４月１４日　火曜日　午後２時４５分 
						

							VQT2A6126
Preparation
Inserting/Removing the Card (Optional)
Check that this unit is turned off.
 Close the flash.
 We recommend using a Panasonic card.
Slide the card door to open it.
Push it fully until it clicks being careful 
about the direction you insert it. To remove 
the card, push the card until it clicks, then 
pull the card out upright.
A : Do not touch the connection terminals of the card.The card may be damaged if it is not fully inserted.
1: Close the card door.
2: Slide the card door to the end and then 
close it firmly.
If the card door cannot be completely closed, remove 
the card, check its direction and then insert it again.
NoteAlways turn the camera off before opening the card door.
 Before removing the card, turn the camera off, and wait until the status indicator has gone off 
completely. (Otherwise, this unit may no longer operate normally and the card itself may be 
damaged or the recorded pictures may be lost.)
DMC-GH1KPP-VQT2A61_eng.book  26 ページ  ２００９年４月１４日　火曜日　午後２時４５分 
						

							27VQT2A61
Preparation
About the Card
Access to the card
The access indication lights red when pictures are being recorded 
on the card.
The following types of cards can be used with this unit.
(These cards are indicated as card in the text.)
¢The SDHC Memory Card is a memo ry card standard decided by the SD Association in 2006 
for high capacity memory cards more than 2 GB.
¢ You can use an SDHC Memory Card in equipm ent that is compatible with SDHC Memory 
Cards however you cannot use an SDHC Memory Card in equipment that is only compatible 
with SD Memory Cards. (Always read the operating instructions for the equipment being 
used.)
 You can only use cards with SDHC logo (indicating compliance with the SD standard) if using 
cards with 4 GB or more capacity.
 It is recommended to use a card with SD Speed Class
¢ with “Class 6” or higher when recording 
motion pictures.
¢ SD speed class is the speed standard regarding continuous writing.
 Please confirm the latest information on the following website.
http://panasonic.co.jp/pavc/global/cs (This Site is English only.)
NoteDo not turn off the power or remove the battery, card, or the DC cable (when the AC 
adaptor is in use), while the access indicator is lit, while writing, reading, or deleting the 
picture, formatting (P38), etc. Also, do not apply vibration, shock, or static electricity to 
the unit.
The card or the data on the card may be damaged, and this unit may no longer operate 
normally.
If operation fails due to vibration, impact or static electricity, perform the operation again.
The data on the card may be damaged or lost due to electromagnetic waves, static electricity or 
breakdown of the camera or the card. We recommend storing important data on a PC etc.
 Do not format the card on your PC or other equipment. Format it on the camera only to ensure 
proper operation. (P38)
 Keep the Memory Card out of reach of children to prevent swallowing.
Card
Ty p e  o f  c a r dCharacteristics
SD Memory Card (8 MB to 2 GB)
(Formatted using the FAT12 or FAT16 
format in compliance with the SD 
standard) 
Fast recording and writing speed
 Write-Protect switch  A provided (When 
this switch is set to the [LOCK] position, 
no further data writing, deletion or 
formatting is possible. The ability to 
write, delete and format data is restored 
when the switch is returned to its 
original position.)
SDHC Memory Card (4 GB to 32 GB)¢
(Formatted using the FAT32 format in 
compliance with the SD standard)
2
A
DMC-GH1KPP-VQT2A61_eng.book  27 ページ  ２００９年４月１４日　火曜日　午後２時４５分 
						

							VQT2A6128
Preparation
Setting Date/Time (Clock Set)
The clock is not set when the camera is shipped.
Turn the camera on.
A [MENU/SET] button
Press [MENU/SET].
Press  2/1 to select the items (year, month, 
day, hour, minute, display sequence or time 
display format), and press  3/4 to set.
A: Time at the home area
B : Time at the travel destination (P115)
‚ : Cancel without setting the clock.
Select either [24HRS] or [AM/PM] for the time display 
format. 
 AM/PM is displayed when [AM/PM] is selected.
 When [AM/PM] is selected as the time display format, midnight is displayed as AM 
12:00 and noon is displayed as PM 12:00. This display format is common in the North 
America and elsewhere.
Press [MENU/SET] to set.
Turn the camera off after finishing setting the clock. Then turn it on and check that the 
clock setting is correct.
 When [MENU/SET] has been pressed to complete the settings without the clock having 
been set, set the clock correctly by following the 
“Changing the clock setting” 
procedure below.
Select [CLOCK SET] in the [SETUP] menu, and press  1. (P30)It can be changed in steps 3 and 4 to set the clock.
 Once a charged battery has been installed for 24 hours, the clock setting is maintained 
for 3 months using the built-in clock battery even without the battery.
Changing the clock setting
ON
OFF
MENU/SET
:
:
DMC-GH1KPP-VQT2A61_eng.book  28 ページ  ２００９年４月１４日　火曜日　午後２時４５分 
						

							29VQT2A61
Preparation
NoteThe clock is displayed when [DISPLAY] is pressed several times during recording.
 You can set the year from 2000 to 2099.
 If the clock is not set, the correct date cannot be printed when you stamp the date on the 
pictures with [TEXT STAMP] (P136) or order a photo studio to print the pictures.
 If the clock is set, the correct date can be printed even if the date is not displayed on the screen 
of the camera.
Setting the Menu
This camera offers menu selections that allow you to customize its operation to maximize 
your picture taking experience.
In particular, the [SETUP] menu contains some important settings relating to the camera’s 
clock and power. Check the settings of this menu before proceeding to use the camera.
Note
There are functions that cannot be set or used depending on the modes or menu settings being 
used on the camera due to the specifications.
!  [REC] mode menu (P116 to 124) [SETUP] menu (P33 to 38)
 This menu lets you 
set the aspect ratio, 
number of pixels and 
other aspects of the 
pictures you are 
recording. 
This menu lets you 
perform the clock 
settings, select the 
operating beep tone 
settings and set 
other settings which 
make it easier for 
you to operate the camera.
 [MOTION PICTURE] mode menu
 (P124 to 125) [MY MENU]
 This menu lets you 
set the [REC 
MODE], [REC 
QUALITY], and other 
aspects for motion 
picture recording. 
Up to 5 menu items 
used recently can be 
memorized. Items 
used a lot can be 
recalled easily.
 [CUSTOM MENU] (P125 to 130)(  [PLAYBACK] mode menu (P132 to 145)
 Operation of the unit, 
such as displaying of 
the screen and 
button operations, 
can be set up 
according to your 
preferences. Also, it 
is possible to register the modified settings. 
This menu lets you 
make the protection, 
trimming or print 
settings (DPOF), etc. 
of recorded pictures.
DMC-GH1KPP-VQT2A61_eng.book  29 ページ  ２００９年４月１４日　火曜日　午後２時４５分 
						

							VQT2A6130
Preparation
This section describes how to select the [REC] mode menu settings, and the same setting 
can be used for the [MOTION PICTURE] mode menu, [CUSTOM MENU] menu, [SETUP] 
menu, [MY MENU] menu and [PLAYBACK] mode menu as well.
If you set [MENU RESUME] (P130) in the [CUSTOM MENU] menu to [ON], the screen shows 
the last selected menu item when the camera was turned off.
Example: Setting [I.EXPOSURE] from [OFF] to [HIGH] in the Program AE Mode
Setting menu items
Turn the camera on.
A [MENU/SET] button
B Mode dial
Set the mode dial to  [ ].
Press [MENU/SET] to display the menu.
Switching to other menus
e.g.: Switching to the [SETUP] menu
1Press  2.
2Press  4 or rotate the front dial 
to select the [SETUP] menu icon [ ].
3Press  1.Select a menu item next and set it.
ON
OFF
MENU/SET
or
DMC-GH1KPP-VQT2A61_eng.book  30 ページ  ２００９年４月１４日　火曜日　午後２時４５分