Panasonic Cs Ks30nku Cu Operating Instructions Manual

							10
4.  Night Setback Mode
Night Setback Mode is used for saving energy.
Press the NIGHT SETBACK button while unit is operating. (except 
FAN mode)
The   mark appears in the display.
To release the night setback function, press the NIGHT SETBACK 
button again.
Pressing the MODE selector button cancels Night Setback mode.
In Cooling and DRY Mode: ( and  )
5.  QUIET Mode
QUIET Mode is used to reduce the fan sound of the indoor unit. 
Press the QUIET button.
The   mark appears in the display.
To cancel, press QUIET button again.
• In QUIET Mode, the fan rotates at a slower speed than the fan 
speed setting.
• If the unit is already operating with a very low airflow, the fan sound 
may not change even if the QUIET button is pressed.
6.  HIGH POWER Mode
HIGH POWER mode can be used to increase the output of the 
indoor unit for all operation modes.
Press the HIGH POWER button while unit is operating.
The   mark appears in the display. 
To cancel, press HIGH POWER button again.
• When the HIGH POWER button is pressed, the unit operates at 
maximum output for 30 minutes, regardless of the desired 
temperature. The fan speed is 1 step above “High”.
• QUIET Mode and HIGH POWER Mode cannot be used at the 
same time.
• Pressing the MODE selector button cancels HIGH POWER mode. 
• Depending on the operating conditions, the fan speed may be 
increased by a small amount only.
NOTE
When the night setback mode is selected, the air conditioner 
automatically raises the temperature setting 2 °F when 30 minutes 
have passed after the selection was made, and then another 2 °F 
after another 30 minutes have passed, regardless of the indoor 
temperature when night setback was selected. This enables you 
to save energy without sacrificing comfort. This function is 
convenient when gentle cooling is needed.
Setting
temperature
Press the NIGHT 
SETBACK button
30 min.30 min.Time
2°F2°F
NOTE 
						

							11
7.  UNOCCUPIED Mode
Unoccupied mode is used to prevent the room temperature from  
increasing too much when no one is in the room, and operate 
automatically to save energy.
Press the UNOCCUPIED button.
The   mark appears in the display. 
To release the unoccupied function, press the UNOCCUPIED button 
again.
Unoccupied Indication
Even if Unoccupied Mode is ON, it will be disabled if the air 
conditioner is in operation.
• Unoccupied Function can be set and released through all 
operational modes, regardless of whether the air conditioner is 
operating or not. 
• If the Unoccupied Function is ON and the remote controller is used 
to turn the air conditioner OFF (including OFF TIMER), the air 
conditioner will turn off, but depending on the room temperature, 
Cooling Operation will automatically begin.
• When the Unoccupied Function is in operation and the ON/OFF 
operation button is pressed, operation will restart based on the 
settings input before the air conditioner was turned off.
In Cooling Mode: ( )
• Unoccupied Mode triggers Cooling Operation in response to the 
room temperature, but when this happens, the remote controller 
will continue to display the Operation mode set by the user.
• If the room temperature rapidly changes, the room temperature 
may get over the upper or lower limit when the unoccupied function 
is activated.
• The remote controller should be used in the location specified in 
“REMOTE CONTROLLER INSTALLATION POSITION” on page 8.
• The air conditioner’s stop order (stated in (2) / above) is valid only 
when the unoccupied function is operated.
Unoccupied 
FunctionUnoccupied 
IndicationStatus
OFF no display The unoccupied function is not set.
ONflashingThe unoccupied function is now 
being set, and under Cooling 
operation.
lightingAlthough the unoccupied function is 
set, not under Cooling operation.
NOTE
(1)
89
86
82
(2)
Room 
Temperature (°F)
Cooling 
startsTime
Cooling 
stops
(1) When the room temperature rises above 89°F, Cooling 
Operation will begin.
(2) When the room temperature drops below 82°F, Cooling 
Operation will stop.
The above actions will repeat so that the room temperature is 
maintained at about 86°F.
NOTE 
						

							12
SPECIAL REMARKS
How it works?
• Once the room temperature reaches the level that was set, the 
unit’s operation frequency is changed automatically.
• During DRY operation, the fan speed automatically runs at lower 
speed for providing a comfortable breeze.
• ‘‘DRY’’ operation is not possible if the indoor temperature is 59 °F 
or less.
• Sometimes the indoor unit may not get to the set fan speed such as 
LOW under cool operation at very low outdoor temperatures due to 
the indoor unit being protected from ice or frost.
• In the event of power failure, the unit will stop. When the power is 
resumed, the unit will restart automatically in approximately 
5 minutes by the remote controller.
If the remote controller is on and left in a location where the unit 
can receive a signal, then the unit will automatically restart in 
approximately 5 minutes of power being restored.
Clicking sound is heard from the air conditioner
• In cooling operation, any plastic parts may shrink due to a sudden 
temperature change. In this event, a clicking sound may occur. This 
is normal, and the sound will soon disappear.
• The remote controller sends the setting condition to the air 
conditioner regularly at five minute intervals.
SETTING THE TIMER
In the descriptions below, the following settings are used for the 
temperature and time indicator selector button on the bottom front 
section of the remote controller.
• Temperature: °F
• Time: AM, PM
1.  How to set the present time
(Example) To set to 10:30 pm.
‘‘DRY’’ ( ) Operation
Cooling ( ) operation
Power failure during operation
Clicking Sound
Remote Controller
Operation Indication
1.Press the CLOCK button 
once if the time indicator is 
not flashing.The time indication alone 
flashes.
2.Press the Advance, Return 
( ,  ) button until PM 10:30 
is displayed.The time can be set in 1-minute 
increments. Holding down the 
button advances the time rapidly 
in 10-minute increments.
3.Press the CLOCK button 
again.This completes the setting of the 
current time.
NOTE 
						

							13
2.  How to set the OFF time
(Example) To stop the air conditioner at 11:00 am.
3. How to set the ON time
(Example) To start operation at 7:10 am.
4. How to set daily ON/OFF repeat timer
(Example) To start operation at 7:10 am. and stop the air conditioner 
at 11:00 am.
• The ON/OFF combination timer uses the current time as the 
reference, and it is activated starting from whichever set time 
comes first.
• With the ON/OFF combination timer, the settings are repeated 
ever y day.
• You can check the timer ON/OFF times after you have set them by 
pressing the ON TIME and OFF TIME setting buttons.
To cancel a timer program
• Press the CANCEL button.
• When either an ON or OFF timer is to be canceled, press the 
button corresponding to the timer whose program is to be 
canceled, and then press the CANCEL button.
• The airflow direction, fan speed and temperature setting can be 
changed after a timer program has been set even when the unit is 
stopped. Even when operation is stopped during an ON timer 
program, the unit will start operating when the set time is reached 
provided that the program is not canceled.
• When the ON timer and OFF timer are set to the same time, the 
timer operates as if it is turned off.
Operation Indication
1.Press the OFF TIME setting 
button once.The timer   indication is 
displayed, and the present OFF 
time is shown.
2.Press the Advance, Return 
( ,  ) button until AM 11:00 
is displayed.The timer   indication 
blinks.
The time can be set in 10-minute 
increments. Holding down the 
button advances the time rapidly 
in 10-minute increments.
3.Wait a few seconds, and then 
the setting is complete.The timer   indication 
stops blinking and the present 
time is displayed.
Operation Indication
1.Press the ON TIME setting 
button once.The timer   indication is 
displayed, and the present ON 
time is shown.
2.Press the Advance, Return 
( ,  ) button until AM 7:10 
is displayed.The timer   indication 
blinks.
The time can be set in 10-minute 
increments. Holding down the 
button advances the time rapidly 
in 10-minute increments.
3.Wait a few seconds, and then 
the setting is complete.The timer   indication 
stops blinking and the present 
time is displayed.
Operation Indication
1.Set the timer ON/OFF times 
as shown in 2-1, 2, 3 and 3-1, 
2, 3.The present time 10:30 pm. and 
 are displayed.
7:10 am. 
ON11:00 am. 
OFF 10:30 pm. 
Present time
NOTE
NOTE 
						

							14
USING THE 1-HOUR OFF 
TIMER
1. 1-Hour OFF Timer
This function causes the unit to operate for one hour and then 
stop, regardless of whether the unit is on or off when this 
button is pressed.
The   indicator in the display indicates that this function is 
operating.
Setting procedure:
Regardless of whether the unit is operating or stopped, press the 1 
HR. TIMER button.
 appears in the display.
Cancellation procedure:
Press the ON/OFF operation button to turn the unit off, wait for the 
unit to stop operating, and then press the ON/OFF operation button 
again. 
The 1-Hour Timer function is now cancelled and the unit operates 
normally.
• If, while the 1-Hour Timer function is operating, the 1HR. TIMER 
button is pressed once to cancel the function and then again, the 
unit continues to operate for one hour from that point in time and 
then stops.
• It is not possible to use the OFF Timer and 1-Hour OFF Timer 
together. Whichever function is set last takes precedence. If the 1 
HR. TIMER button is pressed while the TIMER OFF function 
operates, the OFF Timer is cancelled and the unit will stop 
operating one hour later.
2. Operation together with the daily ON/OFF 
repeat timer
The 1-Hour OFF Timer setting is given priority over the DAILY ON/
OFF REPEAT setting.
TIPS FOR ENERGY SAVING
Avoid
• Do not block neither the air intake nor the air outlet. It may 
cause less performance, and may leads to malfunctions.
• Do not let direct sunlight into the room. Use sunshades, blinds or 
curtains. If the walls and ceiling of the room are warmed by the 
sun, it will take longer to cool the room.
Do
• Always try to keep the air filter clean. (Refer to “CARE AND 
CLEANING”.) A clogged filter will impair the performance of the 
unit.
• To prevent conditioned air from escaping, keep windows, doors and 
any other openings closed.
ADJUSTING THE AIRFLOW 
DIRECTION
1. Horizontal
The horizontal airflow can be adjusted by moving the vertical vanes 
with your hands to the left or right.
When the humidity is high, the vertical vanes should be in the 
front position during the cooling or dehumidifying operation. If 
the vertical vanes are positioned all of the way to the right or 
left, condensation may begin to form around the air vent and 
drip down.
2. Vertical
The vertical airflow can be adjusted by moving the flap with the 
remote controller. Do not move the flap with your hands. Confirm that 
the remote controller has been turned on. Use the FLAP button to 
set either the sweep function or one of the six airflow direction 
settings.
• The flap automatically closes when the unit is off.
NOTE
CAUTION
SWEEP
A. Sweep function 
The flap starts moving 
up and down to deliver 
air over the sweep 
range.
B. Setting the airflow manually
Referring to the above 
illustration, use the 
FLAP button to set the 
airflow direction within 
the range used during 
cooling or 
dehumidifying 
operation.
C. Auto flap function 
The flap is set 
to the 
recommended 
position.
COOL
DRY
FA N
NOTE 
						

							15
• Use the FLAP button on the remote controller to adjust the 
position of the flap. If you move the flap by hand, the flap 
position according to the remote controller and the actual 
flap position may no longer match. If this should happen, 
shut off the unit, wait for the flap to close, and then turn on 
the unit again; the flap position will now be normal again.
• Do not have the flap pointed down during cooling operation. 
Condensation may begin to form around the air vent and drip 
down.
OPERATION WITHOUT THE 
REMOTE CONTROLLER
If you have lost the remote controller or it has trouble, follow the 
steps below.
When the air conditioner is not running
Each time the OPERATION button is pressed, the operation mode 
changes cyclically.
The temperature is set to the room temperature minus 4°F during 
the cooling operation, and the fan speed and flap are set to Auto.
CARE AND CLEANING
Casing and Grille (Indoor Unit)
Clean the casing and grille of the indoor unit with a vacuum cleaner 
brush, or wipe them with a clean, soft cloth.
If these parts are stained, use a clean cloth moistened with a mild 
liquid detergent. When cleaning the grille, be careful not to force the 
vanes out of place.
Filter
The filter behind the front panel should be checked and cleaned at 
least once every two weeks.
How to remove the filter
1.
Grasp both ends of the front panel and pull forward and up to 
open the front panel.
2.Lift the filter up slightly to disengage it from the protrusions on the 
unit.
3.Pull downward to remove the filter from the unit.
Cleaning
Use a vacuum cleaner to remove light dust. If there is sticky dust on 
the filter, wash the filter in lukewarm, soapy water, rinse it in clean 
water, and dry it.
How to replace the filter
1.
Insert the top of the filter, and then secure the bottom of the filter 
with the protrusions on the unit.
2.Close the front panel by pushing the center of the front panel and 
then pressing both edges until the panel clicks into place.
1.For safety, be sure to turn the air 
conditioner off and also to 
disconnect the power before 
cleaning.
2.Do not pour water on the indoor unit 
to clean it. This will damage the 
internal components and cause an 
electric shock hazard.
CAUTION
INDOOR UNIT
OPERATION button (ON/OFF)
OPERATION lamp 
Cooling operationStop
NOTE
1.Never use solvents, or harsh 
chemicals when cleaning the indoor 
unit. Do not wipe the plastic casing 
using very hot water. 
2.Some metal edges and the fins are 
sharp and may cause injury if 
handled improperly; be especially 
careful when you clean these parts.
3.The internal coil and other 
components of the outdoor unit 
must be cleaned every year. Consult 
your dealer or service center.
CAUTION
Protrusions Front panel
filter
12
2 
						

							16
Cleaning the main unit and Remote Controller
• Wipe clean using a soft, dry cloth.
• To remove stubborn dirt, moisten a cloth in warm water no hotter 
than 104 °F, wring thoroughly, and then wipe.
• The front panel can be removed in order to wash it with water.
Removing and remounting the front panel
Removing
Open the front panel until it is nearly horizontal, grasp the sections 
near the front panel arms on both sides, and then remove the panel 
by pushing the arms towards the outside while pulling the panel 
towards you.
If the front panel is difficult to remove, grasp both ends of it and lift it 
up slightly. 
Move it to the left and disengage the left arm, then move it to the 
right and disengage the right arm.
Remounting
Grasp the sections near the front panel arms on both sides, and 
hold the front panel so that it is nearly horizontal. Push the arm 
shafts towards the outside so that they come into contact with the 
top of the indentations on the right and left sides of the air 
conditioner. Then push firmly until the arm shafts click into place. 
After closing the front panel, press firmly on the parts indicated by 
the arrows to securely fasten the panel in place.
Also refer to the figure that shows “How to replace the filter”.
Washing the front panel with water
• Clean the front panel gently using a soft sponge, or the like. Then 
wipe away any remaining moisture.
• Neutral detergent may be used to remove stubborn dirt. Then rinse 
thoroughly with water and wipe away any remaining moisture.
TROUBLESHOOTING 
(BEFORE CALLING FOR SERVICE)
If your air conditioner does not work properly, first check the following 
points before requesting service. If it still does not work properly, 
contact your dealer or service center.
When using a footstool or the like, be 
careful not to let it tip over.
Front panel Arm
CAUTION
Trouble Possible Cause Remedy
Air conditioner does 
not run at all.1. Power failure.  1. Restore power.
2. Leakage circuit 
breaker tripped.2. Contact service 
center.
3. Line voltage is too 
low.3. Consult your 
electrician or 
dealer.
4.  Batteries in remote 
controller have run 
down.4. Replace batteries.
OPERATION lamp 
blinks and air 
conditioner does not 
operate.Trouble in system. Contact service 
center.
Compressor runs but 
soon stops.Obstruction in front of 
condenser coil.
(Outdoor Unit)Remove obstruction.
Poor cooling 
performance.1.  Dirty or clogged air 
filter.1. Clean air filter to 
improve airflow.
2. Heat source or 
many people in 
room.2. Eliminate heat 
source if possible.
3. Doors and/or 
windows are open.3. Shut them to keep 
the heat out.
4. Obstacle near air 
intake or air 
discharge port.4. Remove it to 
ensure good 
airflow.
5. Thermostat is set 
too high for 
cooling.5. Set the 
temperature lower.
Clicking sound is 
heard from the air 
conditioner.In cooling operation, 
any plastic parts may 
shrink due to a 
sudden temperature 
change. In this event, 
a clicking sound may 
occur.This is normal, and 
the sound will soon 
disappear.
OPERATION lamp 
lights but outdoor unit 
will not run.The use of cellular 
phones near the air 
conditioner may 
cause disturbance to 
its normal operation.1. Turn off the power 
then restart the air 
conditioner after a 
while.
2. Consult your 
dealer. 
						

							17
OPERATING RANGE
The air conditioner is operable within the temperature ranges as 
listed below:
WIRED REMOTE CONTROLLER
A separately sold wired remote controller (CZ-RD515U) 
used with this air conditioner is also available. If you wish 
to use the wired remote control function, you will need to 
purchase both the optional wired remote controller and its 
connection kit (CZ-RC515UA).
Temperature Indoor air 
temperature Outdoor air 
temperature
COOLING Max.  95 °F DB / 
71 °F WB 115 °F DB
Min.  67 °F DB / 
57 °F WB 0 °F DB 
						

							18
SPECIFICATIONS
Model No.Outdoor Unit  Indoor Unit
CS-KS30NKU CU-KS30NKUA 
30,600 [ 10,900 ~ 30,600 ]
55Single-phase, 208-230 V, 60 Hz
9.00 [ 3.20 ~ 9.00 ]
-
-
-
-
-
35-13/16×37-1/32×13-3/8
(910×940×340)
-
49/44/39
-
-
Heating Capacity
Operation
Sound
Unit Dimensions (H×W×D)
(Indoor unit : Include panel)
Net Weight Power Source
Cooling CapacitykW
BTU/h
kW
BTU/h
inch(mm)
lbs.(kg)
Cooling
OperationOutdoor (Hi)
Indoor(H/M/L)
Outdoor (Hi)
Indoor(H/M/L)
Heating
Operation
dB(A)
dB(A)
183.0(83.0)11-13/16×41-15/16×9-1/16
(300×1065×230)
32.0(14.5)
Model No.Outdoor Unit Indoor Unit
CS-KS36NKU CU-KS36NKUA
34,000 [ 10,900 ~ 34,000 ]
55Single-phase, 208-230 V, 60 Hz
10.00 [ 3.20 ~ 10.00 ]
-
-
-
-
35-13/16×37-1/32×13-3/8
(910×940×340)
-
49/44/39
-
-
Heating Capacity
Operation
Sound
Unit Dimensions (H×W×D)
(Indoor unit : Include panel)
Net Weight Power Source
Cooling CapacitykW
BTU/h
kW
BTU/h
inch(mm)
lbs.(kg)
Cooling
OperationOutdoor (Hi)
Indoor(H/M/L)
Outdoor (Hi)
Indoor(H/M/L)
Heating
Operation
dB(A)
dB(A)
183.0(83.0)11-13/16×41-15/16×9-1/16
(300×1065×230)
32.0(14.5)
-