Panasonic Commercial Microwave Ovens Ne 1064 Operating Instructions

							How to Operate
C. Programmed Heating:Example: 1 stage; MemoryFad 9 to heat for 3 minutes at HIGH power
1. [EjT]-l
,@
3. Beep tone will sound.(See page 16)
2_stage; Memory Pad 3 (to heat for 3 minutes at HIGH and 2 minutes at DEFROST)12 to program Memory pad.
14 to activate program Lock. Display window
.Press the Memory Pad 9.In Program Lock Mode oven willstart without pressing START
Pad. See page 14.
.Press the START Pad.
Heating willstart.
The time on digital disptay will
count down.i
Allheating willstop.
When opening the door, the displaywillstop blinking.
Example:
See page
See page
.re1
,@
3. Beep tone will sound.(See page 16)
.Press the Memory pad 3.In Program Lock Mode oven willstart without pressing STARTPad. See page 14.
.Press the START pad.
The total time for both staoeswillbe displayed. The timjondigital display will count down.Heating will start..When the oven shifts to the next stage,a single beep tone will sound.
.Allheating will stop.When opening the door, the displaywillstop blinking.
To Sefect Multipe Portion Heating:The.Double.Quantity Pad (x2) is factory set to automatically double the programmed time for multipleportion heating.
Example: Memory pad 5
.Press the DOUBLE QUANTITYPad.
.Press the Memory pad 5.In Program Lock Mode oven willstart without pressine STARTPad. See page 14. -
3. Follow steps 2 and 3 above.
f6ouBLE)
I:W
tEn (l-l
1.
2.
Display Window
-10- 
						

							Prograrnming
- DO NOT OPEN THE DOOR _
The display window MYIT be blank before programming can begin. tf any indicator light isilluminated in the digital Display Window: closeihe door]press sioplneber pad aniwait 1 minute until the Display goes blank.
Display Window
[_--l
A. lltg1ST1llg Memory lads for Singte Stage Heatins:Exampte: To program 30 seconds at Medium power for Nfemory pad Number 5
2 lElrl)*]
.Press the PROG Pad.NOTE:
.lf no PROG lndicator appearedon display, Program Lock shouldbe cancelled. (See page 14.).Do not keep pressing pROG pad
for more than 30 seconds, or afalse failure code may result.
.Press the Memory pad 5.The pad number and the previously
selected time and power level willappear in the display.
.The pad number and StageHeating Indicator will appearin the display again.
.Press the Power Level SelectorPad 2 times. The Memorv pad
display will go out.
.Press Memory Pads 3 and 0.
.Press the PROG Pad again. you
have completed programming
the selected Memory pad forsingle stage heating and doubleheating time for multiple portion
heatin g automatically.
.2 seconds later, the time andpower level setting for singlestage will appear in the disptay.
.2 seconds later, Double QuantityHeating Indicator and then thedouble heating time will appear
in the display.
.2 seconds later, the display
will go blank.
Memory Pad 5 is now programmed
for heating - 30 seconds at MED power
i---=---:---rtrl
tf I
#| 1 nn II  UU It- Ir*1
r-----=:--=----l
tq I[1
,J,
rJtl
.Pffirr
tft
lr I
[a
--9,49c l
tFl
tf i
d+r| 1 nn II t uu Il-j
rt-r
@
ftowER)( LEVELJ
Er.T,-.-l
@
3.
4.
5.
- 11 - 
						

							How to Operate
..,::...
NOTE: Program the remaining Memory Pads as desired by repeating steps 1-5. You may insert up to 10memory Programs.When the PROG indicator is blinking, the program can be cancelled and/or the pad erased bypressing the STOP/RESET Pad.
Display Window
_j!6 r,II .f n II JU IL___-=_j
,J, ,t-ltl
[?IF
Pmt2
lrl
tf I
__j!99_J__---
I rr I
,J 2
[F-ru]
urioer Ia---: - - l
It It__J
rg+------\I rnn II ttut IL__::J
d+i5I Lr tut II tLtLt IL---__-------___
tlII
B. Programming Memory Pads lor 2 or 3 Stage Heating:Example: To program for 2 minutes at DEFROST for 2 stage heating using Memory pad Number 5
1. Complete Steps 1 to 4 on page 1 1
@Press the Power Level Selector Pad
3 times. DEF indicator light will light.
3. Er-Tl-l Ef (l--l Ef , (; .press the Memory pads 2, 0 and 0.
[email protected] the PROG Pad again. You havecompleted programming the SelectedMemory Pad for 2 stage heating anddouble heating time for multiple porlion
heating automatically.
.2 seconds later, the display will confirmyour programming.
.Totaltime for 2 stage programming.
.After all of your programming has beencompleted, the display wiil go blank.
NorE:  Program the remaining pads as desired by repeating the steps above.DO NOT OPEN THE OVEN DOOR during programming. For a 3 stage heating cycle, select a further power level and set the desired heatinq time betweensteps3and4above.
-12- 
						

							How to Opeiab
C Programming the Double Quantity Pad - For multiple portion heating:
Your oven is factory set to automatically double the programmed time for multiple portion heating - this isthe correct setting for heatin_g multiple portions of most small foods items. No furthbr programming of thetime is necessary for these food items.The time required to heat multiple portions of some large platters and most bulk food loads is slighily lessthan double that of a single portion. 
This model incorporates a Multiple Portion Heating Custom Program feature that allows you to customizethe heating time and/or power level for multiple portions of yourhenu items.For example, if Memory Pad 3 is set for 6 minutes at DEFF{OST, 12 minutes at DEFROST is set for doublequantity heating automatically. Ho_wever, if your gwn tests have determined that the correct heating timesrequired is less (only 10 minutes 30 seconds at.DEFROST) for two portions, the Multiple portion ileatingCustom Program feature can be programmed for 1O minuies 30 seconds at DEFROST.Example: To program 30 seconds at HIGH Power on Memory Pad Number 2 (display must be blank)
@
,W
3. Erl]_l
4. fP-odi)(. LEVRJ
.Press the PROG Pad.
NOTE:.lf no PROG Indicator appeared ondisplay, Program Lock should becancelled (see page 14)..Do not keep pressing PROG Pad lormore than 30 seconds, or a false
failure code may result.
.Press DOUBLE OUANTITY (x 2) pad.
.Press the Memory Pad 2.
The pad number and the previously
selected time and power level for
multiple portion heating will briefty
appear in the display.
.The pad number and Stage Heating
Indicator will reappear in the display.
.Press the Power Level Selector Padonce. The Memory Pad display willgo out.
.Press the Memory Pads 3, 0.
.Press the PROG Pad again. You
have completed programming the
selected Memory Pad for multiple
portion heating.
.2 seconds later, the setting for single
stage heating will appear in the display.
.2 seconds later, the display will go blank.
Disglay Window
d-t+-rtJltL IrJ
(g;t=--1I Ltl-t I| t I\----_:____-_J
o toottI ,l+3xi - )l: I
[ I
Lr
: ,,*
[:ilr-l
I PF6f:...---=----1t1 IlL I
ffi-__-]
i- JU I
[--l
NOTE:  Program the remaining Memory Pad as desired by repeating steps 1-6 above. (You may insert up to1O memory programs.)
DO NOT OPEN THE OVEN DOOR during programming. When the PROG indicator is blinking, the program can be cancelled and/or the pad erased bypressing STOP/RESET Pad.
-13- 
						

							How to Operate
Other Features
A. To Activate Program Lock:
This procedure Lockslhe controlpanelMemory Pads into their programmed heating timeslevels. Do Nor OPEN THE DooR. The Display window must be btink before theProgram Lock feature can be activated.
@.Press and hold in the PROG pad
until the display shows P and L.
(for 6 seconds)
.Program Lock feature is now
activated.
NoTE: Do 1ot press PROG Pad for longer than 30 seconds continuously, or false failure code may result..ln Program Lock
a. To activate preset programs, open door will display,0.b. The oven is started by pressing the desired Memory pad. There is no need to press the STARTpad.
c. The interrupt feature is deactivated-opening the door cancels the remaining time on theprogram.
d. The oven cannot be programmed until the program lock feature is deactivated.
B. To Release Program Lock:
This procedure deactivates Program Lock and activates all other features. Oven reverts to a 2 touchoperating mode (Memory pad plus START pad).
DO NOT OPEN THE DOOR. The Display Window must be blank before the Retease AispUv-WingsluProgram Lock feature can be activated.
ii
NoTE: Do not press PRoG Pad for longer than 30 seconds continuously, or false failure code may result.ln Program Unlock,
a. Repeat and interrupt features are operational.b.lr/emory pads can be programmed.
c. Tone loudness control is operational.
ano power
Oisolay Window
ll
Fn-r[ - |
.Press the STOp/RESET pad andwhile pressing this pad, press thePROG Pad untitthe disptay showsP (for 6 seconds).
.Program Lock Feature is deactivated.oven is now in Program Unlock mode.
-14- 
						

							How to Operate
C. To Read Program List:
Allows you to review all currently programmed Pad Number, heating time and power level for each stage.
1. Open the door.
f sTot)
UESETJ
+
1y*,J
2.
Display Window
f---- n I
I ul.While pressing the STOP/RESET Pad,press and hold in the START Pad.
The Bgep Tone setting will show in thedisplay window.
Example: Stage Indicator 1: Beep tone is ONStage.Indicator 2: Beep tone is OFF.2 seconds later, the Program Lock
setting will show in the display
window.
Program Lock : P L
Program Unlock: P
3. tEFI---il.Press the Memory Pad you desired
to read program.
Example: The Memory Pad Number 5.Display window will display;
Program Memory Pad
Number 5, first stage heating
time and power level currentlyprogrammed on Memory Pad.
2 seconds later the same
information will be displayed
for the 2nd and 3rd stage
heating.
.After all settings have been
displayed, the Pad Number and
the Stage Heating Indicator will
appear in the display again.
NOTE: lf you want to go to another program, press the Memory Pad you desire in order to read program,
while the information of Memory Pad is being displayed.lf you want to show the Multiple Portion Heating (x 2) program, press the DOUBLE QUANTITYPad before pressing the Memory Pad.
-15- 
						

							How to Operate
D. To Select Beep Tone Options:
The Beep Tone can be set, ON or OFF.
1. Open the door.
@
3 mll_l
Display Window
i---- nl
I ul
f- nl
I ul
trFTFl
oM2r.....-...---)
lbrrP I
tr t,l-
f--;
I Li
E. To Read the Cycle Counter:
1. Open the door.
.@
@
+
fPo!ml
ILEVEL
The. oven can display the total number of times the oven has been operated cumulatively. Great foranalyzing usage of the oven and traffic flow at the location.
.Press the PROG Pad. The displav willnot change.
.Press the Memory pad.
.Repeat pressing of O Pad. Select OFF
of Beep Tone.
Stagelndicatorl =ON
Stagelndicator2=OFF
.Press the PROG Pad again. you havecompleted programming the beep tone.
.2 seconds later, 0 willappear in thedisplay.
 close dooY z Seconds lulra the
d;s7l Nindow w;1 0o lloaK-
.While pressing STOp/RESET pad, pressPower Levet Selector pad. The displayshows the totalcumulative number of -
times the oven has been used.Example:.9999 means, the oven has beenused 999900 times..0020 means the oven has beenused 2000 times.. lf the total cumulative numberof times less than 100 times, thedisplay will not be changed..2 seconds later, 0 will appear inlhedisplay window.
f---;l
I Li
a_-_--l)
I LiLlLlLll
L--:::-J
2.
-16- 
						

							$elf Diagnostics Failure Code Explanation
This oven monitors its operation and displays a Failure Code in the display window when a problem occurs.
What to do when a failure code appears:
NOTE: Above codes shown in display do not indicate all the possible failures on the unit
Care of Your Microwave Oven
1. Unplug the oven belore cleaning.
2. Keep the inside of the oven clean. When food
spatters or spilled liquids adhere to oven walls, wipe
with a damp paper towel. Mild detergent may be
used if the oven gets very difi. The use of harsh
detergent or abrasives is not recommended. The air
intake splash guard/light diffuser can be removed
for cleaning by removing the cenler plugs lrom the
two plastic rivets. The top is held by two tabs.
Wash in warm dishwater and replace.
3. The outside oven surfaces should be cleaned with
a damp paper towel. To prevent damage to the
operating parts inside the oven, water should not
be allowed to seep into the ventilation openings.
4. lf the Control Panel becomes wet, clean with a soft,
dry cloth. Do not use harsh detergents or abrasives
on Control Panel. When cleaning the Control
Panel, leave oven door open to prevent oven from
accidentally turning on. After cleaning, touch
STOP/RESET Pad to clear display window.
5. lf steam accumulates inside or around the outside
of the oven door, wipe with a soft paper towel. This
may occur when the microwave oven is operated
under high humidity conditions and in no way
indicates malfunction of the unit.
6. Clean off the grease and dust on bottom surfaces
often. Use warm detergent solution.
7. Cleaning inside the oven outer panel and inside the
oven base should be performed only by qualified
service personnel after taking precautions to drain
all stored voltage potential. The bottom is
accessible by removing the center section of the
base and the power and sensor control areas are
within the outer wrap around housing. Avoid using
liquids and cleaning solutions in these areas. Use a
dry soft bristle brush or a cloth. Replace all parts-
Do not connect the oven to the electricity supply if
any pads are nol reassembled.
CODECAUSEWHAT TO DO
F01*Overcooked food.Temperature of exhaust air too high.
*Press STOP/RESET Pad to stop beep.-Unplug oven and wait at least 30 minutes
before reconnecting.-Wait for oven to cool down and reset.-lf a flame is present, do not open oven door.lf normal operation does not resume, call the
service agent with information of failure code.
F33-34.Defective sensor circuit Unplug the oven and wait more than 10
seconds before reconnecting.
* lf normal operation does not resume, call the
service agent with the information of failure
code.
F44-When a pad was pressed for more
than 30 seconds-Defective oad or control circuit
-17 - 
						

							Notes
-18- 
						

							Technical $pecifications
1T
Zltt 15
Front View
NE-1064
Power Source120V, 60 Hz, single phase
Required Power13.4 A 1500 w
Output1000 w
Frequency2,450 MHz
Outer Dimensions
(HxWxD)
12 x20% x 14%
(306mmx51Ommx360mm)
Cavity Dimensions
(HxWxD)
8%o x13 x 13
(205mmx33Ommx330mm)
Net WeightApprox. 37 lbs. (16.8 kg)
Shipping WeightApprox. 42 lbs. (19.0 kg)
Timer99 min 99 sec (Digital) x 10 Memory Pads with Doubte Quantity(x2) Pad
lEC 705-88 Test Procedure
Specifications subject to change without notice
ZOtta29s
..---_..8
1r
Side view with Open Door
23le 871e.
Side View
tf
-19-