Panasonic Color Cctv Cameras Wv Cp254h Operating Instructions

							1. Loosen the focus lock knob.
2. Adjust the focus lock knob to obtain a focused
point while watching the monitor screen.
3. Tighten the focus lock knob.
Caution:Tightening the knob by force will
cause damage to the knob or deviation
of focus.
Note:The object may be out of focus when
using a source of near-infrared light than
using the visible light.
FOCUS OR FLANGE-BACK ADJUSTMENT
Pick-up device: 752 (H) x 582 (V) pixels, interline transfer CCD
Scanning area: 5.59 (H) x 4.68 (V) mm (equivalent to scanning area of 1/3 in.
pick-up tube)
Synchronization: internal, line-locked or multiplexed vertical drive (VD2), 
selectable 
Scanning system: 2 : 1 interlace
Scanning: 525 lines / 60 fields / 30 frames
Horizontal: 15.734 kHz
Vertical: 59.94 Hz
Horizontal resolution: 480 lines
Video output: 1.0 V [P-P] NTSC composite 75 
Ω/ BNC connector
Signal-to-noise ratio: 50 dB (min) (at AGC Off, weight On)
Electronic light control: equivalent to continuous variable shutter speed between 1/50 s
and 1/15 000 s
Minimum illumination: 1.0 lx (0.1 foot-candle) at color mode, 0.15 lx (0.015 foot-candle) at
black and white mode with F1.4 lens
Aperture: SHARP or SOFT, selectable 
Lens mount: CS-mount
Ambient operating temperature:
−10 °C - +50 °C (14 °F - 122 °F)
Ambient operating humidity: less than 90 %
Power source and
power consumption: 24 V AC 60Hz, 3.3 W
Dimensions (without lens): 67 mm (W) x 65 mm (H) x 72.5 mm (D)
2-5/8 (W) x 2-9/16 (H) x 2-7/8 (D)
Weights (without lens): 0.33 k
g(0.7 lbs)
Day/Night selectable COLOR FIX (→external terminal active) or AUTO
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
SPECIFICATIONS
STANDARD ACCESSORIES
Operating Instructions (this document)  ............................................. 1 pc.
The following parts are for installation:
Body cap  ........................................................................................... 1 pc.
ALC lens connector (YFE4191J100) .................................................. 1 pc.
C-mount Adapter  ............................................................................... 1 pc.
OPTIONAL ACCESSORIES
Lenses: WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3, 
WV-LA908C3, WV-LZ61/10, WV-LZ62/2, WV-LZ62/8, WV-LF4R5C3A, WV-LF9C3A,
WV-LZ61/15, WV-LZA61/2, WV-LZF61/2
W
V-CP254H CP254H
Loosen
Tighten
Focus lock
knob
Caution for Mounting the Lens
The lens mount should be a C-mount or CS-mount
(1”-32UN) and the lens weight should be less than
450 
g(0.99 lbs). If the lens is heavier, both the lens
and camera should be secured by using the sup-
porter.
The protrusion at the rear of the lens should be as
shown below.
C-mount: Less than 13 mm (1/2”)
CS-mount: Less than 8 mm (5/16”)
Day/Night Connections
Connect an optical sensor to the Day/Night Input
terminals.
•Day/Night Input terminals with a capacity of
5V DC pull-up input, 0.2 mA or more.
OFF:break contacts: color pictureON:make contacts: black-and-white pictureNote:To activate the Day/Night function, set
Day/Night Mode Selector to COLOR FIX.
PANASONIC CANADA INC.5770 Ambler Drive, Mississauga, 
Ontario, L4W 2T3 Canada (905)624-5010
PANASONIC SALES COMPANY
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC.
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina, 
P.R. 00985 (809)750-4300
Panasonic Digital Communications & Security CompanyUnit of Matsushita Electric Corporation of AmericaSecurity Systems Groupwww.panasonic.com/cctvExecutive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094Zone Office
Eastern:One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303Central:1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205Western:6550 Katella Ave., Cypress, CA 90630 (714) 373-7840
2003     © Matsushita Electric Industrial Co., Ltd.  All rights reserved.
CONNECTIONS
AUTO:The camera selects black-and-white
mode if the picture is dark, or color mode
if the picture is bright enough.
Notes:•When using this unit with a video servo
control lens, you may not switch from the
black-and-white mode to the color mode
depending on lens iris.
In such a case, operate the lens adjuster
to open the aperture.
•This function may not be activated auto-
matically when a backlight or a strong
light source causes excessive contrast in
the picture. In such cases, use the
Day/Night input terminals.
!3Duration Time SelectorThis selector is available when the Day/night
switch position is AUTO.
Switching time (5 sec. or 1 minute ) is selec-
table.
!4BW Level Selector Selects the luminance level.
This selector is available when the Day/night
switch position is AUTO.
According to the luminance level, this camera
automatically switches the condition of picture
from color to black-and-white, or in reverse.
HI:Color picture switches to black-and-white
pictures at approx. 7 lx with F1.2 lens.
LOW:Color picture switches to black-and-
white pictures at approx. 5 lx with F1.2
lens.
The factory default setting is HI.
!5Power Indicator (POWER)
!6Day/Night Input Terminal
(DAY/NIGHT IN/GND)
This terminal is used for connecting the cam-
era to an external day/night detecting sensor.
Terminals opened: color picture
Terminals shortened: black-and-white picture
!7Video Output Cable with BNC ConnectorConnects the VIDEO IN connector of the mon-
itor.
!8Power Cable
Cautions:
1. CONNECT THIS TO 24 V AC CLASS 2
POWER SUPPLY ONLY. Be sure to connect
the grounding lead to the GND terminal.
2. To prevent fire or electric shock hazard,
use a UL listed cable (VW-1, style 1007) for
the Input Terminal.
3. The connections should comply with
National Electrical Code (NEC).
■Connections
Caution:The following connections should be made by qualified service personnel or system installers in
accordance with NEC 725-51.
Note:For the WV-CP254H Color CCTV Camera, do not use a transformer larger than 10VA.
Power Cable
Video Output Cable
To Video IN
(CAMERA IN) BNC PlugGreen/Yellow (Ground) White (Neutral)Black (Live)
BNC Plug
BNC Plug
24 V AC, 60 Hz
(19.5 V-28 V)
(CLASS 2 SUPPLY ONLY)
WV-CP254HCP254H
Cautions:1. Shrinking the cable-entry seal is a one-time
procedure. Do not shrink the cable-entry
seal until it has been ascertained that the
unit is functioning.
2. CONNECT THIS TO 24 V AC CLASS 2
POWER SUPPLY ONLY. Be sure to connect
the grounding lead to the GND terminal.
3. To prevent fire or electric shock hazard,
use a UL listed cable (VW-1, style 1007) for
the Input Terminal.
4. The connections should comply with
National electrical Code (NEC).
Copper wire
size (AWG)
Length
of cable
(Approx.)(m)
(ft)#24
(0.22mm2)
20
65#22
(0.33mm2)
30
100#20
(0.52mm2)
45
160#18
(0.83mm2)
75
260
Video Cable
1. It is recommended to use a monitor whose
resolution is at least equal to that of the
camera.
2. The maximum extensible coaxial cable
length between the camera and the monitor
is shown below.
Type of RG-59/U RG-6/U RG-11/U RG-15/Ucoaxial cable (3C-2V) (5C-2V) (7C-2V) (10C-2V)
Recommended (m) 250 500 600 800
maximum
cable length (ft) 825 1 650 1 980 2 640
Installation of Auto Iris Lens
Connector
Install the lens connector (YFE4191J100) when
using a video drive ALC lens.
The installation should be made by qualified
service personnel or system installers.
Cut the iris control cable at the edge of the lens
connector to remove the existing lens connector
and then remove the outer cable cover of the sup-
plied connector as shown in the diagram.
The pin assignment of the lens connector is as fol-
lows:
Pin 1: Power source; +9 V DC, 50 mA max.
Pin 2: Not used
Pin 3: Video signal; 0.7 V[p-p]/40 k
ΩPin 4: Shield, ground
Pin 3
Pin 4
Pin 2
Rib
Pin 1
Mounting the Lens
Caution:Before you mount the lens, loosen the focus
lock knob, and rotate it clockwise until it
stops. If the ring is not at the end, the inner
lens or CCD image sensor may be damaged.
qMount the lens by turning it clockwise on the
lens mount of the camera.
Note:When mounting the C-mount lens on
the camera, mount the C-mount adapter
by rotating it clockwise in advance.
wConnect the lens cable to the auto iris lens
connector on the side of the camera.
Lens mount
Focus lock 
knob
C-mount adapter
w
W
V-CP254H CP254H
Solder the lens cable to the pins of the sup-
plied connector.
• Power supply connection
Recommended wire gauge sizes for 24 V AC line.
1. The following functions are built in.
(1) Auto Light Control (ALC)/Electronic Light
Control (ELC)
(2) Automatic Gain Control (AGC) and
Automatic Tracing White Balance (ATW)
(3) Camera synchronization mode selectable
between internal (INT), Line-locked (LL)
and Multiplexed Vertical Drive (VD2).
2. Minimum Illumination of 1.0 lx (0.1 foot-can-
dle) at color mode, 0.15 lx (0.015 foot-candle)
at black and white mode with F1.4 lens.3. Signal-to-noise ratio of 50 dB (min)
(at AGC OFF, weight ON)
4. Horizontal resolution of 480 lines
5. Auto iris lens control selectable between
video signal and DC power supply.
6. Auto black-and-white mode enables the cam-
era to switch between color and black and
white picture in response to light input.
FEATURES
1. Do not attempt to disassemble the camera.To prevent electric shock, do not remove
screws or covers.
There are no user serviceable parts inside.
Ask a qualified service person for servicing.
2. Handle the camera with care.Do not abuse the camera. Avoid striking,
shaking, etc. The camera could be damaged
by improper handling or storage.
3. Do not expose the camera to rain or
moisture, or try to operate it in wet areas.
Turn the power off immediately and ask a
qualified service person for servicing.
Moisture can damage the camera and also
create the danger of electric shock.
4. Do not use strong or abrasive detergents
when cleaning the camera body.
Use a dry cloth to clean the camera when
dirty.
In case the dirt is hard to remove, use a mild
detergent and wipe gently. Afterwards, wipe
off the remained part of the detergent in it with
a dry cloth.
5. Clean the CCD faceplate with care.Do not clean the CCD with strong or abrasive
detergents. Use lens tissue or a cotton tipped
applicator and ethanol.
6. Never face the camera towards the sun.Do not aim the camera at bright objects.
Whether the camera is in use or not, never
aim it at the sun or other extremely bright
objects. Otherwise, blooming or smear may
be caused.
7. Do not operate the camera beyond the
specified temperature, humidity or power
source ratings.
Use the camera under conditions where tem-
perature is between –10 °C - +50 °C (14 °F -
122 °F), and humidity is below 90 %. The input
power source is AC 24 V.
8. Do not connect this camera during a
lightning storm.
Otherwise, electric shock may be caused.
PRECAUTIONS
Day /
NightGND
IN
POWER
ewq
r !7
!6
!8
WV-CP254H
!5
Fixing screws Camera mounting
screw holes
Mount adapter
ONBLCAGC
HI
LOW
SOFTDC VIDEOOFF
SHARP
ELC
ALC
LLATW2 ATW1HI
LOW5SEC1MINAUTO
COLOR
FIXINT
DAY/NIGHT
ONBLCAGC
HI
LOW
SOFTDC VIDEOOFF
SHARP
ELC
ALC
LLATW2 ATW1HI
LOW5SEC1MINAUTO
COLOR
FIX
INT
DAY/NIGHT
out!1!3
!0
iy!2!4
Pull and remove the cap
WV-CP254H CP254H
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
qAuto Iris Lens ConnectorSupplies power and control signals to an auto
iris lens (not supplied).
wFocus Lock KnobThis knob adjusts the back-focal distance or
picture focus.
eLens (option)
rMount AdapterThe camera mounting screw hole is for mount-
ing the camera onto a mounting bracket. The
camera is originally designed to be mounted
from the bottom, however, a top-mounting
type is also available. To mount from the top,
remove the mount adapter from the bottom of
the camera by removing two fixing screws.
Attach the mount adapter to the top as shown
in the diagram, then mount the camera on the
mounting bracket. Make sure that two original
screws are used when mounting the mount
adapter; longer type screws may damage
inner components, too shorter type screws
may cause the camera drop.
tSynchronization Mode Selector (INT, LL)Selects the camera synchronization mode as
either internal sync mode (INT) or line-lock
mode (LL).
INT:Sets to internal 2:1 interlace.LL:Sets to Line-lock mode.
yBack Light Compensation Mode Selector
(BLC ON, OFF)
Lets you select the mode according to the
position of the object and light conditions on
the screen.
ON:Select this mode when a strong light
such as a spotlight is in the background.
OFF:Normal picture
The factory default setting is ON.
uAGC Level Selector
AGC level can be selected with this selector.
AGC automatically controls the gain of Image
brightness level.
HI:This setting raises more the gain and
brightness of images under low light con-
ditions.
LOW:Normal position
iDetail/Aperture Level Selector (SHARP,
SOFT)
The detail/aperture level can be selected with
this selector. Set it to the desired position
while observing the picture on the monitor.
SHARP:Normal position.SOFT:Select this position when a Quad
System is connected to this camera.
oAutomatic Light Control/Electronic Light
Control Selector (ALC, ELC)
Lets you select the mode according to the
lens type used.
ALC:Select this mode when an auto iris lens
(ALC lens) is used with this camera.
ELC:Select this mode when a fixed iris lens
or manual iris lens is used with this cam-
era.
!0Lens Drive Signal Selector (VIDEO, DC)Lets you select the mode according to the
type of auto iris lens drive signal to be sup-
plied to the lens from the auto iris lens con-
nector.
VIDEO:Select this mode if you are using a
auto iris lens that requires a video drive
signal.
DC:Select this mode if you are using a auto
iris lens that requires a DC drive signal.
!1Auto-Tracing White Balance mode (ATW)
Selector
The ATW mode can be selected with this
selector.
ATW1:Normal pictureATW2:ATW in sodium lamp mode
!2Day/Night Mode SelectorThis function switches the condition of pic-
tures from color to black and white in low light
conditions.
COLOR FIX:Color picture reverts to black-
and-white picture when an external
day/night switching signal is received
(refer to Day/Night connections).
Note:When using this unit with infrared
rays or lighting of which color tem-
perature is 3 000 K or less, select
this mode without fail, and short-cir-
cuit the Day/Night input terminals if
you select the black-and-white pic-
ture.
(The AUTO mode may cause hunt-
ing.)
Model No.WV-CP254H
Color CCTV Cameras
Operating Instructions
W
V-CP254H
(Lens: Option)
PREFACE
Panasonic’s WV-CP254H digital signal processing
color CCD camera introduces a new level of high
picture quality and high resolution through the use
of a 1/3-inch interline transfer CCD image sensor
having 752 horizontal pixels (picture elements),and digital signal processing LSI’s. This model
offers cutting-edge technology for advanced video
surveillance.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
N0703-1103      3TR001812BAA      Printed in Japan
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and mainte-
nance (servicing) instructions in the
literature accompanying the appli-
ance.
The lightning flash with arrowhead
symbol, within an equilateral trian-
gle, is intended to alert the user to
the presence of uninsulated dan-
gerous voltage within the products
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The serial number of this product may be found on
the top of the unit.
You should note the serial number of this unit in the
space provided and retain this instruction as a per-
manent record of your purchase to aid identification
in the event of theft.
Model No.  WV-CP254H
Serial No. SA 1966
SA 1965
WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture. 
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SER-
VICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed
and used in accordance with the instruction manu-
al, may cause harmful interference to radio com-
munications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case
the user will be required to correct the interference
at his own expense.
FCC Caution: To assure continued compliance,
(example - use only shielded interface cables when
connecting to computer or peripheral devices). Any
changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate this equipment.For U.S.A
Caution:To prevent fire or electric shock hazard,
use a UL listed cable (VW-1, style 1007) for
the AC 24 V Input Cable. 
						

							BRANCHEMENTS
Remarque:Lorsque cet appareil est
utilisé avec des rayons infrarouges ou
un éclairage dont la température de
couleur est égale ou inférieure à
3000 K, sélectionner absolument ce
mode et shunter les bornes dentrée
Diurne/nocturne si lon sélectionne
des images monochromatiques.
(Le mode AUTO risque de provoquer
une recherche.)
AUTO:La caméra vidéo sélectionne le mode
noir et blanc si limage est foncée ou le
mode couleur si limage est assez
lumineuse.
Remarques:•Lorsque cet appareil est utilisé avec un
objectif à servocommande vidéo, il est
possible de commuter du mode noir et
blanc au mode couleur en fonction du
diaphragme de lobjectif.
Dans ce cas, actionner le dispositif de
réglage de lobjectif pour ouvrir
louverture de lobjectif.
•Cette fonction risque de ne pas être
activée automatiquement quand une
puissante lumière en arrière-plan ou une
source déclairage engendre un
contraste excessif de limage. Dans ce
cas, utiliser les bornes Diurne/Nocturne.
!3Sélecteur de duréeCe sélecteur est disponible lorsque la position
du sélecteur Diurne/nocturne est AUTO.
La durée de commutation (5 sec. ou 1 minute)
peut être sélectionnée.
!4Sélecteur de niveau BW Sélectionne le niveau de luminance.
Ce sélecteur est disponible lorsque la position
du sélecteur Diurne/nocturne est AUTO.
Précautions:1. RACCORDER UNIQUEMENT À UNE
SOURCE D’ALIMENTATION 24 V C.A. DE
CLASSE 2. Faire en sorte de raccorder le fil
de terre à la borne GND.
2. Pour prévenir tout risque dincendie ou
délectrocution, utiliser un câble UL indiqué
dans la liste (VW-1, style 1007) pour la
borne dentrée.
3. Les connexions doivent être conformes aux
normes de National Electrical Code (NEC).
■Connexions
Précaution:Les branchements doivent être confiés à un dépanneur de système qualifié ou à des installateurs de
système professionnels en conformité à NEC 725-51.
Remarque:Dans le cas de caméra vidéo couleur CCTV WV-CP254H, ne pas se servir dun
transformateur dalimentation plus puissant que 10VA.
Cordon d’alimen-
tation
Câble de sortie vidéoPrise BNC Vert ou jaune (terre) Blanc (Neutre)Noir (actif)
Prise BNC 
Prise BNC 
24 V de courant alternatif, 60 Hz 
(19,5 V - 28 V) (UNIQUEMENT 
UNE ALIMENTATION DE 
CLASSE 2)
À VIDEO IN 
(CAMERA IN)
WV-CP254HCP254H
Précautions:1. Le rétrécissement de la gaine d’isolement
en bout de câble s’effectue en une seule
fois. Ne pas rétrécir la gaine d’isolement en
bout de câble avant d’avoir vérifié que
l’appareil fonctionne normalement.
2. RACCORDER UNIQUEMENT À UNE
SOURCE D’ALIMENTATION 24 V C.A. DE
CLASSE 2. Faire en sorte de raccorder le fil
de terre à la borne GND.
3. Pour prévenir tout risque dincendie ou
délectrocution, utiliser un câble UL indiqué
dans la liste (VW-1, style 1007) pour la
borne dentrée.
4. Les connexions doivent être conformes aux
normes de National Electrical Code (NEC).
Calibre de fil de
cuivre (AWG)
Longueur
de câble
(environ)(m)
(ft)#24
(0.22mm
2)
20
65#22
(0.33mm2)
30
100#20
(0.52mm2)
45
160#18
(0.83mm2)
75
260
Câble vidéo
1. Il est recommandé d’utiliser un moniteur vidéo
dont la résolution est au moins égale ou
supérieure à celle de la caméra vidéo.
2. La longueur de câble coaxial extensible
maximum placé entre la caméra vidéo et le
moniteur vidéo est indiquée ci-dessous.
Broche 3
Broche 4
Broche 2
Nervure
Broche 1
Souder le câble de lobjectif aux broches du
connecteur fourni.
Installation de l’objectif
Précaution:Avant que vous ne montiez lobjectif sur la
caméra vidéo, desserrez la vis qui se trouve
sur la caméra vidéo, puis tournez la bague
dans le sens des aiguilles dune montre
jusquà ce quelle se bloque. Si la bague ne se
trouve pas en fin de course, loptique
intérieure ou le capteur dimage D.T.C.
risquent dêtre endommagés.
qMonter l’objectif sur la caméra vidéo en le
tournant dans le sens des aiguilles d’une
montre sur la monture d’objectif de la caméra
vidéo.
Remarque:Quand un objectif à monture C est
installé sur la caméra vidéo, installer
ladaptateur de monture C en le faisant
tourner dans le sens des aiguilles dune
montre.
• Raccordement dalimentationCalibres normalisés des fils de connexion
recommandés pour une alimentation à courant
alternatif 24 V.En fonction du niveau de luminance, cette
caméra vidéo commute automatiquement les
conditions des images du noir et blanc à la
couleur ou linverse.
HI:Limage en couleur se commute en noir et
blanc à environ 7 lux avec un objectif
ouvrant à F/1,2.
LOW:Limage en couleur se commute en noir
et blanc à environ 5 lux avec un objectif
ouvrant à F/1,2.
Le réglage implicite dusine est fait sur HI.
!5Lampe t