Panasonic Color CCTV Camera Wv Cw590 Wv Cw594 Installation Guide

11
Take not\bce of hum\bd\H\bty.
Insta\f\f this product when the humi\,dity is \fow. If this 
product is insta\f\fed \,during rainfa\f\f or \,at a high humidity\,, 
the inside may be \,exposed to moistur\,e and the dome 
cover may become fo\,ggy. 
Locally procure the\H screws
Screws  are  not  supp\fied  with  this  product.  Prepare  the 
screws  according  to  the  materia\f,  structure,  strength 
and  other  factors  of  the  mounting  area  and  the  tota\f 
weight of objects t\,o be mounted.
Screw...

12
\bIP swit\fh settings 
■ Commun\bcat\bon Parameters (DIP Sw\btch 2) 
\bhe factory defau\ft settings \,are a\f\f OFF. Sw\btch 1: \berminator (Interna\f \bermination Resistanc\,e)
 Set to ON in the f\,o\f\fowing situations.
  • When 1 camera is c\,onnected to this u\,nit
  • When  2  or  more  cameras  are  connected  to  this  unit  that  works  as  a 
termination
Sw\btches 2 to 4: Communication Par\,ameters \bhis  setting  togg\fes  between  2-\fine  and  4-\fine  communication.  Use 
these switches...

13
■ Un\bt Number (DIP Sw\btch 1) 
\bhe factory defau\ft settings \,of these DIP switch\,es are a\f\f OFF. (Coaxia\f Mu\ftip\fex\, System) 
Conf\bgurat\bon for u\Hs\bng  Panason\bc Pro\Htocol
1 2 34
ON5 6 7
8
DIP Switc\f 1 Unit 
Nu\bber
1 2 3 4
ON5 6 7 8
1 2 3 4
ON5 6 7 8
1 2 3 4
ON5 6 7 8
1 2 3 4
ON5 6 7 8
1 2 3 4
ON5 6 7 8
1 2 3 4
ON5 6 7 8
1 2 3 4
ON5 6 7 8
1 2 3 4
ON5 6 7 8
1 2 3 4
ON5 6 7 8
1 2 3 4
ON5 6 7 8
1 2 3 4
ON5
6 7 8
1 2 3 4
ON5 6 7 8
1 2 3
4
ON5 6 7 8
1 2 3
4
ON5 6 7 8
1 2 3
4
ON5 6 7 8
1...

14
1 2 34
ON
5 6 78
DIP Switc\f 1 Unit 
Nu\bber
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
56 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8 1 2 3
4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3 4
ON
5 6 7 8
1 2 3...

15
■ RS485 Commun\bcat\bon Parameters (DIP Sw\btch 1) 
Configuring DIP Switch 1 as shown be\fow resets communication parameters to their factory defau\ft settings. You can 
then change the se\,ttings as desired. 
1 2 34
ON5 6 7
8
DIP Switc\f 1 Setting De\bcription
1 2 3 4
ON5 6 7 8
1 2 3 4
ON5 6 7 8
1 2 3 4
ON5 6 7 8
ON
1 2 3 4
ON5 6 7 8
T\fi\b \betting re\bet\b communication parameter\b to t\fe factory default \betting\b.
BAUD RATE : 19 200\c bit/\b, DATA BIT : \c8 bit, PARITY CHEC\cK : NONE, STOP BIT\c...

16
Installation
Precaut\bons
 •  Make sure that the p\face you are insta\f\fing the camera is strong enough to support it. If it is not strong enough, 
then the camera ma\,y fa\f\f and hurt someone.
  •  \bhe  fo\f\fowing  steps  of  insta\f\fation  and  connection  work  shou\fd  be  done  by  qua\fified  service  personne\f  or 
system insta\f\fers a\,nd shou\fd conform to a\f\f \foca\f codes\,.
  •  Be sure to turn the power off before insta\f\fation and \,connection.
  •  Do not insta\f\f the...

17
x4 Screws
STEP 6
Fix the housing ba\,se to the attachme\,nt pipe.•   Fasten  4  screws  (the  screws  that  were  removed  in 
 step  3)  making  sure  that  "REAR "  engraved  on  the 
 housing base face\,s the wa\f\f.
(Recommended tightening torque: 2.45 N·m {25 kgf·cm})
•   Fi\f\f  the  gap  between  the  bracket  and  attachment 
pipe  with  waterproof  materia\f  such  as  si\ficon  c\fay.
See instructions o\,f the bracket for \,detai\fs.
Important: 
•  Carefu\f\fy  app\fy  the  sea\fing...

18
 (2) Be sure to hook the camera safety wire into the bracket.
Camera Saf ety Wire
  (3)  Insta\f\f  the  camera  to  the  housing  mounting 
b a s e .   I n s t a \f \f   t h e   c a m e r a   t o   t h e   h o u s i n g 
mounting  base  so  that  the  guide  pin  at  the 
camera  top  wi\f\f  be  directed  toward  "REAR" 
engraved  on  the  housing  mounting  base.  \burn 
the  camera  counter-c\fockwise,  viewed  from  the 
bottom,  to  confir m  that  the  camera  is  fixed. 
Secure\fy...

19
Important: 
•  Joint both sides of the front and rear sunshie\fds 
before fitting in the m\,ain sunshie\fd.
•   Do not trap the sa\,fety wire inside.
•   \bhe safety wire is designed to support on\fy the 
weight of the camer\,a when the camera f\,a\f\fs.  
Do not put an exce\,ssive weight that th\,e safety 
wire cannot support.
STEP 9
Fit the front and rear sunshie\fds in t\,he main sunshie\fd.
•  A\fign  "
"  of  the  rear  sunshie\fd  to  "  S\bAR\b"  of  the 
m a i n   s u n s h i e...

20
Conne\ftions 
Precaut\bons
 •  \bhe  fo\f\fowing  connections  shou\fd  be  made  by  qua\fified  service  personne\f  or  system  insta\f\fers  in  accordance 
with a\f\f \foca\f codes.
  •  See the reverse side of the \,cover page for main\, \fead connection.
  •  \burn off the power at the fuse box before starting the insta\f\fation work, or it so cou\fd resu\ft in fire, e\fectric shock, 
persona\f injury, and materia\f dama\,ge. 
 Data Port (RS485)Alarm In\fut Conne\btorAlarm Out\fut Conne\bto\nr...