Panasonic Color CCTV Camera Wv Cw504 Series Installation Guide

							21
 w  Engage the attachment mounting screw of 
the camera with the camera mounting hole 
of  the  camera  attachment  and  rotate  the 
camera  in  the  direction  of  the  arrow  to  the 
"LOCK"  position  to  secure  the  camera  to 
the  camera  attachment  without  any  back-
lash. 
  e  Connect  the  power  cord  and  the  video 
output  cable  at  the  side  of  the  mounting 
base. (+ page 30)
    Apply  waterproof  treatment  to  the  con-
nected section. (+ page 28)
  r  Accommodate  the  connected  cables 
inside  the  cable  guide  of  the  mounting 
base. 
Important:
	 •	 To	 prevent	 the	cables	 from	being	 caught	
when  the  cover  is  attached,  keep  the 
cables inside the cable guide. 
    
LOCKOPEN
LOCKOPEN
Projections
Make cable 
connections. 
Cable guide
Cable guide
Connected cable 
						

							22
 t  Mount  the  supplied  base  cover  on  the 
mounting base. 
Important:
	 •	 To	 prevent	 the	cables	 from	being	 caught	
when the base cover is attached, keep the 
cables inside the cable guide. 
  y  Use  the  bit  for  tamperproof  screw  (acces-
sory)  to  tighten  the  fixing  screws  provided 
on both sides of the base cover. 
    (Recommended tightening torque:  
0.78 N·m {0.58 lbf·ft})
Base cover
Base cover fixing screw 
						

							23
x   Remove the enclosure and inner 
dome from the main body by loos-
ening the three fixing screws. 
    Loosen the three fixing screws by using the 
provided bit for tamperproof screw. 
    Detach  the  inner  dome  while  pushing  the 
parts with the "PUSH" indication.
Important:
	 •	 Do	 not	hold	 the	inner	 dome	 when	carrying	
the  camera.  Otherwise,  the  camera  part 
may fall and it may damage the camera. 
Note:
	 •	 Perform	 the	same	 procedure	 when	replac-
ing  with  the  optional  dome  cover  WV-
CW4S. 
c    Secure the camera to the bracket 
with the camera fixing screw (red, 1 
position). 
Important:
	 •	 The	 camera	fixing	screw	 shall	be	securely	
tightened.  Otherwise,  water  exposure  may 
cause  damage  or  malfunction  of  camera, 
or  camera  dropping  may  result  in  injury. 
(Recommended tightening torque: 
    0.78 N·m {0.58 lbf·ft})
v   Remove the screw (blue, 1 position) 
for transport protection with a 
Phillips screw driver. 
Press the parts with the 
PUSH indication.
Screw for transport protection (blue)
Camera xing screw (red) * The camera xing screw 
shall be securely tightened. 
						

							24
Adjust the camera
z
   Be sure to view the monitor for adjustment when the camera angle is adjusted. \
    Connect  the  monitor  for  adjustment  (e.g.  a  small  LCD)  to  the  monitor  output  connector,  and 
adjust the camera angle. 
    When  determining  the  camera  angle,  repeat  fine  follow  the  adjusting  procedure  of  q, w,  and 
e shown below. 
  q Loosen the panning lock screw and rotate the camera head horizontally to adjust panning, 
and tighten the panning lock screw. 
  w Loosen  the  tilting  lock  screws  and  rotate  the  camera  head  vertically  to  adjust  tilting,  and 
tighten the tilting lock screw. 
  e Rotate the tilt adjusting table, and adjust the azimuth angle of the ima\
ge. 
Important:
	 •	 The	panning	lock	screw	and	the	tilting	lock	screw	shall	be	securely	tightened.	
    (Recommended tightening torque: 0.59 N·m {0.44 lbf·ft})
Note:
	 •	 The	 video	output	 to	the	 BNC	 connector	 will	be	interrupted	 while	an	adjusting	 monitor	is	con-
nected to the monitor output connector.
	 •	 At	the	same	time	for	the	pan	and	tilt	adjustments,	make	focus	adjustments	of	Step	2.	
    
LOCK LOCK LOCK LOCK 
75 °
Tilting lock screw
Monitor output connector 
(RCA)
Tilt adjusting table
Panning lock screw Panning table 
						

							25
x Adjusts the focus.
    Focus adjustment shall be performed when camera 
angle adjustment are performed. 
    Adjust  the  focus  by  following  the  adjusting  proce-
dure of q, w, and e shown below. 
  q Loosen the zoom lock knob and move the knob 
between  TELE  and  WIDE  to  obtain  the  appro-
priate  angle  of  view,  and  then  tighten  the  zoom 
lock knob. 
  w Loosen  the  focus  lock  knob,  make  coarse 
adjustment  of  the  focus,  and  then  tighten  the 
focus lock knob. 
  e Perform  major  adjustment  of  back  focus 
through  the  setup  menu  or  perform  major 
adjustment by following Steps 3 and 4 below (+ Operating Instructions (PDF)). 
Note:
	 •	 Reset	 the	back	 focus	 position	 to	the	 CS	mount	 default	 position	 before	the	back	 focus	 adjust-
ment.  (Hold  down  the  right  and  left  buttons  simultaneously  for  2  seconds  or  more,  or  move  the 
cursor to "MANUAL-ADJ" of "BACK-FOCUS SETUP" in the setup menu and press the right and 
left buttons simultaneously for 2 seconds or more after pressing the setting button.)
c    Press the [ABF1] button after adjusting the view angle while viewing the m\
onitor 
for adjustment. 
    The  ABF  operation  indicator  (+  page  12)  lights,  the  focus  position  is  displayed  in  the  lower  part 
of the screen, and the back focus is automatically adjusted. 
TELETELE WIDEWIDE
FAR
FAR
NEARNEARZoom lock knobFocus lock knob
 NEAR       FAR
  .........
|..........
INDICATOR XXXX FOCUSING 
						

							26
v   To perform fine adjustment of the back focus after the ABF operation indi\
cator 
goes off and automatic back focus is adjusted, use the right or left button. 
Note:
	 •	 No	operation	for	10	seconds	or	more	automatically	clears	the	focus	position	indicator.	
	 •	 To	 change	 the	angle	 of	view	 by	moving	 the	zoom	 adjustment	 ring,	also	move	 the	focus	 lock	
knob to adjust the focus. 
	 •	 The	 originally	 adjusted	focus	may	be	slightly	 off	depending	 on	the	 iris	state	 resulting	 from	the	
focal depth of the lens. In such a case, open the aperture by darkening the subject as much as 
possible in the same way of taking picture, and then adjust the focus. Defocus can be prevent-
ed. 
	 •	 Use	 of	"ABF"	 of	"BACK-FOCUS"	 in	the	 setup	 menu	 (+  Operating  Instructions  (PDF))  allows 
users to adjust the focus optimally in the range of the capability to automatically follow the vari-
ation in illuminance. 
	 •	 The	 out-of-focus	 level	in	the	 near-infrared	 light	region	 may	be	higher	 than	that	in	the	 visible	 light	
region. 
    Setting  "C/L  ↔  B/W"  of  "BACK-FOCUS  SETUP"  to  "AUTO"  or  "PRESET"  in  the  setup  menu 
(+ Operating Instructions (PDF)) allows users to adjust the focus in both the near-infrared light 
and visible light regions (The variation in illuminance is not followed after focus adjust\
ment.).  
						

							27
b   Mount the enclosure and inner 
dome. 
    Tighten  the  screws  that  have  been  loos-
ened  in  Step  2  in  page  23  using  the  sup-
plied driver bit.
    (Recommended tightening torque:  
0.78 N·m {0.58 lbf·ft})
Important:
	 •	 Attach	 the	inner	 dome	 in	accordance	 with	
the lens direction to not to change the lens 
direction. 
	 •	 Check	 if	the	 tabs	 of	the	 inner	 dome	 are	
firmly fit. 
	 •	 Remove	 the	cushioning	 (pink	sheet)	 from	
the  inside  of  the  dome  and  the  protection 
sheet from the outside of the dome.
Note:
	 •	 Defocus	 may	be	caused	 by	the	 reinstalled	 enclosure.	 When	using	a	system	 controller	 (option),	
adjust  the  back-focus  on  the  setup  menu  after  attaching  the  enclosure.  (+  Operating  Instruc-
tions (PDF))
	 •	 When	 not	using	 a	system	 controller,	 by	using	 the	[ABF2]	 button	back-focus	 adjustment	is	avail-
able after attaching the enclosure. The procedure for the use of the [ABF2] button is as speci-
fied below. 
  q Press the [ABF2] button. → The ABF operation indicator will start blinking. 
  w While the indicator is blinking (for around 3 minutes), attach the enclosure to the camera. 
  e When the indicator changes to steady light, back-focus will be adjusted automatically. After 
the back-focus is adjusted, the indicator will go out. 
  * Do not aim the camera to objects continuously moving. 
  * If the indicator blinks again after changing to steady light, back-focus adjustment may have 
failed. In this case, check the back-focus on the LCD monitor. 
    To adjust the back-focus again, perform Step q to e again. 
    Cutout for 
mounting  Groove for 
mounting  
						

							28
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when the camera with exposed cables is 
installed  by  means  of  the  mounting  base  WV-Q115  or  it  is  installed  under  the  eaves.  The  camera 
body is waterproof, but the cable ends are not waterproof. 
Be sure to use the supplied butyl tape at the connection parts of the power cord and video output 
cable  to  apply  waterproof  treatment  in  the  following  procedure.  Failure  to  observe  this  may  cause 
water leakage resulting in malfunction.

Stretch  the  tape  by  approx.  twice  (see  the  illustration  below)  and  wind  it  around  the  cable.  Insuffi-
cient tape stretch causes insufficient waterproofing. Note:
	 •	 To	 install	this	product	 outdoors,	 be	sure	 to	waterproof	 the	cables.	 The	camera	 body	is	water -
proof (IEC IP66 or equivalent) only when installation specified in this document and appropriate 
waterproofing are properly performed. The bracket is not waterproof. 
	 •	 The	cable	shall	be	wound	with	butyl	tape	in	a	half-overlapping	manner.	
    
When using power 
cord
When using video output cable
Dobled length
Stretch the tape to about twice. 
						

							29
Important:
	 •	 If	 open	wiring	 is	conducted,	 be	sure	 to	use	 conduits	 and	run	the	cables	 inside	the	tubes	 to	pro-
tect the cables from direct sunlight. 
	 •	 When	 the	conduit	 is	connected	 at	the	 lateral	 or	bottom	 position,	 either	of	the	 arrow	 marks	 on	
the bracket shall be the top position.
	 •	 When	 the	conduit	 is	connected	 from	the	top,	 the	arrow	 mark	on	the	 attachment	 shall	be	either	
of the right or left position. 
    
    
	 •	 For	 installation	 on	the	 wall,	 do	not	 connect	 the	dehumidifying	 device	at	the	 upper	 side	to	pre-
vent water from being stored in the dehumidifying device. 
    If water remains inside, the dehumidifying device cannot function properly. 
	 •	 Installation	 work	shall	be	such	 that	there	 is	no	 intrusion	 of	water	 into	the	architecture	 through	
the conduits having been joined.
Arrow mark
Connecting
conduit
FRONT TOP 
						

							30
Make a connection
Cautions:
	 •	 ONLY	CONNECT	WV-CW504	TO	24	V	AC	OR	12	V	DC	CLASS	2	POWER	SUPPLY.
	 •	 Be	sure	to	connect	the	grounding	lead	to	the	GND	terminal.
* When using 12 V DC power supply,
the optional heater unit is unavailable. To 24 V AC/12 V DC* 
power supply
V ideo output cable 
(approx. 16 cm {52.5 ft}) Brown (Live)
Blue (Neutral)
Green/
Yellow (GND)
To GND (only for 24 V AC)
BNC connector BNC connector
BNC connectorTo VIDEO IN
Power cord  
(approx. 17 cm 
{55.8 ft})
l Video output connection
The  video  output  connector  is  connected  to 
the  monitor  or  other  system  devices  with  a 
coaxial cable (locally procured). 
The maximum extensible length is shown in the 
table. 
Type  of  coaxial 
cable
RG-59/U 
(3C-2V) RG-6/U 
(5C-2V) RG-11/U 
(7C-2V) RG-15/U 
(10C-2V)
Recommended 
maximum  cable 
length m 250 500 600 800
ft 825 1 650 1 980 2 640
l Power connection
Precaution:
    The following connections should be made 
by  qualified  service  personnel  or  system 
installers in accordance with NEC 725-51. 
    
• Wire colors & functions
Camera power cord
Wire color 24 V AC 12 V DC
Brown 24 V AC (L) Positive
Blue 24 V AC (N) Negative
Green/yellow To GND –
Cautions:
	 •	 Be	 sure	to	connect	 the	GND	 (grounding)	
lead of the camera and grounding terminal 
of the power supply when using a 24 V AC 
power source. 
	 •	 Shrinking	 the	cable-entry	 seal	is	a	onetime	
procedure.  Do  not  shrink  the  cable-entry 
seal  until  it  has  been  ascertained  that  unit 
is functioning. 
    ONLY  CONNECT  THIS  TO  24  V  AC  or  12 
V DC CLASS 2 POWER SUPPLY.