Panasonic Color CCTV Camera Wv Cw500 Series Installation Guide

11
Mounting screws
	 •	 The	screws 	and 	bolts 	must 	be 	tightened	
with  an  appropriate  tightening  torque 
according  to  the  material  and  strength  of 
the installation area.
	 •	 Do 	not 	use 	an 	impact 	driver. 	Failure 	to	
observe this may cause overtightening and 
consequently damage to the screws.  
	 •	 W h e n 	a 	s c re w 	i s 	t i g h t e n e d , 	m a k e 	t h e	
screw  at  a  right  angle  to  the  surface.  After 
tightening  the  screws  or  bolts,  perform 
visual check to ensure...

12
Major operating controls and their functions
q Power cord
* This illustration shows the camera  without the inner dome.
w Video output cable
e Enclosure
r Panning table
!8 ABF operation indicatorOperation
buttons
!7 Heater output connector
o Zoom lock knob i Focus lock knob
t
Tilt adjusting table
y Tilting lock screw  u Panning lock screw
!0 Camera xing screw
!1 Monitor output connector
!9 Inner dome
!2 Right button
     [(RIGHT), FAR]
!3 Left button
     [(LEFT), NEAR]
!4 Up button
     [(UP)]
!5...

13
 q  Power cord
	w  Video output cable
  e  Enclosure
  r  Panning table
    Rotate  this  table  to  adjust  the  panning 
angle of the camera.
  t  Tilt adjusting table
    Adjust the azimuth angle of the image. 
  y  Tilting lock screw 
    Locks the tilt position. 
  u  Panning lock screw
    Fixes the panning table.
  i  Focus lock knob
    Locks the focal point. 
	o  Zoom lock knob
    Locks the zoom point. 
  !0  Camera fixing screw
    Fix the attachment on the camera body. 
  !1  Monitor...

14
Preparations
When  installing  the  camera  on  a  wall  or  a  ceiling,  there  are  two  methods  as  specified  below.  
(+ Next page)
	 •	 Using	a	two-gang	junction	box
	 •	 Using	the	camera	mount	bracket	(accessory)
Refer  to  all  work  related  to  the  installation  of  this  product  to  qualified  service  personnel  or  system 
installer. 
Important:
	 •	 Prepare	 the	mounting	 screw	according	 to	the	 material	 of	the	 area	 where	 the	camera	 attach-
ment  (accessory)  is  to  be...

15
Using a two-gang junction box
	 •	 When	the	camera	 is	installed	 using	the	two-gang	 junction	box,	mount	 the	camera	 attachment	
(accessory) to the embedded box installed on the wall or ceiling as a \
first step.  
Note:
	 •	 For	wall	mounting:	
    Installation  shall  be  performed  in  such  a  manner  that  "MTOP"  of  the  camera  attachment  faces 
upward. 
  •  For ceiling mounting: 
    The front side (model number indication face) of the camera shall be aligned in the direction of...

16
z Install the camera mount bracket on the wall/ceiling.
Note:
	 •	 Only	 the	same	 type	of	holes,	 A  or B,  shall  be 
used for mounting. 
    
B B
B
A
A
A
51mm
ø27 mm
Cable access hole
Center of camera mount bracket
Female thread for conduit
Camera mount braket
(For use of the hole A) (For use of the hole B)
138 mm
138 mm85 mm
85 mm
(A For use of the hole)
B
B B
B A
A
A
A 

17
x   Previously run the cables from the wall or ceiling through the cable access hole. 
c   Mount the attachment onto the mount bracket. 
    Recommended tightening torque: 0.78 N·m
Camera attachment
FRONTTOP
Note:
  •  For wall mounting: 
    Installation  shall  be  performed  in  such  a  manner  that  "MTOP"  of  the  camera  attachment  faces 
upward. (Except for the case of connecting the conduit from the top. (+ page 28))
  •  For ceiling mounting: 
    The front side (model number...

18
Camera installation
z Mount the camera. 

 q  Connect the power cord and the video output cable. (+ page 29)
  w  Align the "OPEN" mark of the camera with the protrusion of the camera attachment. 
  e  Engage  the  attachment  mounting  screw  of  the  camera  with  the  camera  mounting  hole  of  the 
camera attachment and rotate the camera in the direction of the arrow to the "LOCK" position 
to secure the camera to the camera attachment without any backlash. 
FRONTTOP
OPEN
LOCK...

19

 q  Attach the camera onto the camera attachment 
while  aligning  the  "OPEN"  mark  of  the  camera 
with the projection of the camera attachment.
Important:
	 •	 When	 mounting	the	camera	 body,	cables	 shall	
be  run  between  the  camera  attachment  and 
camera  mount  bracket  as  indicated  by  the 
arrow in the illustration. 
  * Cable  running  as  indicated  by  the  arrow  is  an 
example.  Cable  running  shall  be  varied  with 
installation environment. 
    
LOCKOPEN
LOCKOPEN...

20
 w  Engage the attachment mounting screw of 
the camera with the camera mounting hole 
of  the  camera  attachment  and  rotate  the 
camera  in  the  direction  of  the  arrow  to  the 
"LOCK"  position  to  secure  the  camera  to 
the  camera  attachment  without  any  back-
lash. 
  e  Connect  the  power  cord  and  the  video 
output  cable  at  the  side  of  the  camera 
mount bracket. (+ page 29)
    Apply  waterproof  treatment  to  the  con-
nected section. (+ page 27)
  r  A c c o...