Panasonic Color CCTV Camera Wv Cw304 Wv Cw314 Wv Cw324 Installation Guide

11
Precautions for installation
Panasonic assumes no responsibility for 
injuries or property damage resulting from 
failures arising out of improper installation 
or operation inconsistent with this 
documentation.
Installing place
Contact  your  dealer  for  assistance  if  you  are 
unsure of an appropriate place in your particu-
lar environment.
	 •	 Make	 sure	that	the	installation	 area	is	strong	
enough  to  hold  the  product,  such  as  a 
concrete ceiling.
	 •	 Install	 the	camera	 in	the...

12
Radio interference
W h e n   t h e   c a m e r a   i s   u s e d   n e a r   T V/ r a d i o 
antenna,  strong  electric  field  or  magnetic  field 
(near  a  motor  or  a  transformer),  images  may 
b e   d i s t o r t e d   a n d   n o i s e   s o u n d   m a y   b e 
produced.  In  such  a  case,  run  the  camera 
cable through specialized steel conduit tubes.
Take notice of humidity.
Install this product when the humidity is low. If 
this product is installed at a high humidity, the 
inside  may...

13
Major operating controls
Safety wireCamera mount 
bracket
Sunshield
Front cover Rear cover Tilting lock 
screwPanning lock screwVideo output 
connector
Power cord
Yow lock screw
Set 
buttonIR LED
Lens
Packing
Monitor output 
jack
  

14
Preparations
The camera can be directly mounted on the wall or ceiling.
Important:
	 •	 Prepare	the	mounting	 screws	according	 to	the	 material	 of	the	 area	 where	 the	camera	 mount	
bracket  is  to  be  installed.  In  this  case,  wood  screws  and  nails  should  not  be  used.  Recom-
mended tightening torque M4: 1.60 N·m {1.18 lbf·ft}
	 •	 Required	pull-out	capacity	of	a	single	screw/bolt	is	196	N	{44.06	lbf}	or	more.
	 •	 If	 a	wall	 or	ceiling	 board	such	as	plaster	 board	is	too	 weak	 to...

15
φ 75 mm
Cable access hole
Installation template label
Camera fixing screw x3
(locally procured)

Recommend 
screw (M3) Safety wire Spring washer
(accessory)
Foundation or other 
parts of the building 
with sufficient strength
Recommend 
screw (M3) Safety wire
Spring 
washer Foundation or 
other parts of 
the building with 
sufficient strength
Installation
Affix  the  installation  template  label  (accessory)  to  the  ceiling  or  wall,  and  use  a  pen  to  mark  the 
positions  of  the  screws...

16
Connections
Connect the video output
Important: 
	 •	 Be	sure	to	turn	off	the	power	of	each	device before connecting. 
	 •	 Be	sure	to	secure	the	coaxial	cable	
connectors.
Connect  a  coaxial  cable  (locally  procured)  to 
the video output connector.
Connect the power supply
Connect  the  two-color  conductor  cable  of  the 
camera  to  the  power  supply.  The  colors  and 
functions of the conductors are shown below. 
Color 12 V DC
24 V AC
Brown Positive 
Live
Blue Negative
Neutral Video output...

17
Note:
   How to wind the supplied waterproof tape 
(accessory)
	 •	 S t r e t c h 	t h e 	t a p e 	b y 	a p p r o x . 	t w i c e 	( s e e 	t h e	
illustration) and wind it around the cable. Insufficient 
tape stretch causes insufficient waterproofing.
	 •	 To 	i n s t a l l 	t h i s 	p r o d u c t 	o u t d o o r s , 	b e 	s u r e 	t o 	
waterproof  the  cables.  Waterproof  grade  (IEC  IP66 
or  equivalent)  is  applied  to  this  product  only  when  it 
is  installed  correctly  as  described  in...

18
1  Be sure to view the monitor for adjustment when the camera angle is adjusted.
  Supply power to this unit, connect the monitor for adjustment (e.g. a small LCD) to the monitor 
output  jack,  and  adjust  the  camera  angle  (turn  off  the  power  after  view  angle  adjustment  for 
safety).
   1 Loosen the 2 fixing screws of the front cover to remove the front cover.
Adjustment
  2 Unscrew and remove the front cover.
  3   Connect the adjustment monitor output jack to monitor output jack with  φ...

19
Important:
	 •	 This	video	output	 is	intended	 for	confirmation	 of	view	 angle,	 etc.	during	 installation	 or	repair	
service, and not for recording or monitoring.
Note:
	 •	 Monitor	 output	jack	has	higher	 priority	 than	video	 output	 connector.	 Video	cannot	 be	output	
through the video output cable after connecting the adjustment monitor.
Mind  Your HandMind  Your Hand
Tilting lock screw
Yow lock screw Panning lock screw
Warning Label
  4    Repeat the steps (1) and (2) to adjust the camera...

20
Note:
	 •	 Do	not	put	 your	 hands	 on	the	 safety	 warning	 label	when	 the	camera	 angle	is	adjusted,	 unless	
your hands will be clamped when the front portion of camera falls.
	 •	 Use	 a	hexagonal	 wrench	with	width	 across	 flats	of	3	mm	 (locally	 procured)	 to	loosen	 or	tighten	
the yow lock screw, panning lock screw and tilting lock screw. 
	 •	 Approximately	 1	rotation	 of	loosening	 the	yow	 lock	screw,	 ℃panning	 lock	screw	 and	tilting	 lock	
screw allows camera angle adjustment. Do not...