Panasonic Color Cctv Camera Wv Cs854b Operating Instructions

-41-
NORMAL:Sets the horizontal resolution to more
than 480 lines.
HIGH:Sets the horizontal resolution to more than
510 lines.
Note:After selecting HIGH, noise may increase
when the SENS UP function is activated under
low illumination.
•Digital Noise Reduction (DNR)
DNR may be used to improve quality under low
light conditions. There are 4 levels of DNR, which
may be selected depending on local site
conditions. Factory default setting: LOW2
You may need to try different settings to find the
most suitable...

-42-
•PIX OFF Setting (PIX OFF)
In this setting, you can assign a blemish position
and compensate the blemish.
1. Move the cursor to PIX OFF and press the CAM
(SET) key. The PIX OFF menu appears.
2. Select a number and press the CAM (SET) key. The
blemish compensation position setting screen
appears.
Move the joystick to place the + cursor on the
blemish position. After moving the + cursor to a
position where the blemish looks inconspicuous,
press the CAM (SET) key. Consequently, the
blemish compensation...

-43- For WV-RM70, hold down the right and left switches
simultaneously for 2 seconds or more.
For WV-CU360C/CJ and WV-CU161C, hold down the
[4] and [6] keys simultaneously for 2 seconds or more.
RS485 Setup
Initial Camera Communication
Parameters
In an RS485 chain, the matrix switcher, PC, controllers
and cameras should be set to the same protocol and
parameters for communication. Confirm the system
protocol and parameters prior to setting the
communication parameters for the camera.
The initial...

-44-
Menu
TOP MENU
SPECIAL 1
CAMERA MENU
SPECIAL 2HOME POSITION
SELF RETURN
AUTO MODE
AUTO PAN KEY
DIGITAL FLIP
PASSWORD LOCK
PRIVACY ZONE
PROPO.P/T
AREA TITLE
PATROL
CLEANING
EL-ZOOM
PRESET ALM
IMAGE HOLD
TILT ANGLE
CAMERA ID
ALC/MANUAL
SUPER-D2
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
CHROMA GAIN
AP GAIN
PEDESTAL
RESOLUTION
DNR
BW
PIX SENS UP
BURST (BW)OFF
OFF
OFF
AUTO PAN
ON
OFF
OFF
ON
OFF
STOP
OFF
ON
OFF
OFF
0°
OFF
ALC
OFF
AUTO
ON (MID)
OFF
INT
ATW1
OFF
AUTO L
••••I••••
••••
I••••
••...

INSTALLATION
1. Disassembling the Camera
(1) Loosen the fixing screw to separate the camera
mounting base and the camera. Push up the
screwdriver once before removing the screw.
(2) Turn the camera mounting base approximately 15
degrees counterclockwise and remove the base
from the camera.
2. Setting the Switches
The 8-bit DIP switch has two functions.  It is used to
restore the factory default settings and to specify the
unit number.  Before setting, peel off the seal covering
the switch holes. After...

-46-
Unit Number
Switch 1, an 8-bit DIP switch, specifies the unit number or restores the factory
default settings when using the Panasonic protocol.
When the switch position corresponding to the unit number 1 - 96* is selected,
setting should be made on the RS485 SET UP menu (see page 43).
1234 ON5678
8-bit DIP SW
For Panasonic’s Protocol
1234 ON5678
Switch positionUnit
number
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234...

-47-
1234 ON5678
Switch positionUnit
number
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
Switch positionUnit
numberSwitch positionUnit
number
69
70
71
72
73
74
75
76
7778
79
80
81
82
83
84
85
8687
88
89
90
91
92
93
94
951234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678
1234 ON5678 

-48-
Notes:
•Defaults are marked with *.
•BP stands for Bit Position.
•Full duplex is not available in a daisy chain
connection. (Panasonic system controllers only)
3. Assemble the Camera
Reverse the disassembly procedure. Take care not to
cut any cables.
Precaution:Be sure to select a ceiling board strong
enough to support 4 times the total weight of the
camera.
a. Sideway Cable Exit
Prepare a cutout in the diecast case and decoration
cover as shown in the following figures.
Cutout in Diecast Case...

-49- 3. Hook the fall prevention wire on the camera
mounting base.
Cautions:
•Use the supplied dust protection sheet if the camera
mounting base is liable to be exposed to a dusty
atmosphere. Remove the cover from the dust
protection sheet, then stick the sheet on the camera
mounting base.
•Remove the sheet before mounting the camera on
the base.
•While the camera is separated from the base, keep
the camera in the supplied polyethylene sack.
4. Mount the camera on the camera mounting base
and rotate the...

CONNECTIONS
How to Assemble the Cable with the Accessory
Connector
Strip back the cable jacket approx. 3 mm (0.1 inch)
and separate the individual conductors.Prepare the individual conductors for clamping. Use
MOLEX band tool part number 57027-5000 (for UL-
Style Cable UL1015) or 57026-5000 (for UL-Style
UL1007) for clamping the contacts.
After clamping the contacts, push them into the proper
holes in the accessory connector of this camera until
they snap in place.
CAUTIONS
•Shrinking the cable-entry...