Panasonic Color CCTV Camera Wv Cp600 WV CP620 WV CP604E WV CP624E Series Installation Guide

							11
Locally procure the screws
Screws are not supplied with this product. 
Prepare the screws according to the material, 
structure, strength and other factors of the 
mounting area and the total weight of objects  
to be mounted.
Screw tightening
 • The  screws  and  bolts  must  be  tightened  
with an appropriate tightening torque 
according to the material and strength of 
the installation area.
 • Do  not  use  an  impact  driver.  Failure  to 
observe this may cause overtightening 
and consequently damage to the screws.
 • When  a  screw  is  tightened,  make  the 
screw at a right angle to the surface. After 
tightening the screws or bolts, perform 
visual check to ensure tightening is 
enough and there is no backlash.
Power cord (only for WV-CP600/G‚  
W V-CP620/G)
Connect the power cord securely. Run the  
power cord so that no load is applied to the 
cord when panning or tilting the camera. 
(Failure to observe this may disconnect the 
power cord, and accordingly no image is 
displayed.) 
						

							12
Major operating controls and their functions
(Side view)(Bottom view)
(Rear view) 

4
5
UPSET7
123
220 V-240 V    ~50/60 HzVIDEO OUT
2
1
8
3
24V~IN2-N1-L123
12VIN-,VIDEO OUT6
82
3
(UP)UP
(DOWN)SET
(LEFT)(RIGHT)
1   AC power input terminal [220 V-240 V 
   ~50/60 Hz]
   
Connect with the supplied power cord.
2   Video output connector [VIDEO OUT] 
  Provides video output to system units.
3  Tripod mount base
   This is used to install the camera onto the  
mount bracket (locally procured).
4  ALC lens connector
   Connects to ALC lens (4-pin).
5  Back focus adjustment screw
  Adjusts the back focus distance and  
image focal length.
6  Power input terminal [12 V  IN, 24 V~IN]
   
  The power supply of 24 V AC or 12 V DC is 
connected to this terminal.
7  Setup button [SET]
  Press the [SET] button once and the "FOCUS  
ADJUSTMENT" screen will be displayed.
    Hold down the [SET] button for more than  
2 seconds and the setup menu screen will 
be displayed.
• [LEFT]/[RIGHT]: Press the [RIGHT] or [LEFT]
button to move to the right or left in the 
menu, or change the displayed values.
• [UP]/[DOWN]: Press the [UP] or [DOWN] 
button to move up or down in the menu.
(The directions of "UP", "DOWN", "LEFT" 
and "RIGHT" are as shown when you are 
directly facing "UP".)
• [SET]: Press this button in the menu to 
confirm the selected value or function.
In addition, this button is used to open 
submenus.
8  External I/O terminal
  Used for connections with external devic-
es. 
						

							13
Installation and connection
1 Rotate the lens (option) clockwise slowly to mount the lens.
Important:
 • CS-mount lens can be used on this camera. For use of C-mount lens, use the C-mount adap-
tor (option).
 • For  prevention  of  damage  to  the  camera  body,  use  a  lens  with  protrusion  of  5.5  mm  or  less  
from the flange surface. 
Protrusion from mount: 
20 mm or less
Protrusion from flange:  
5.5 mm or less
Optional dedicated lens
Lens typeModel No.
ALC lens for 1/3-type CCD cameras2x vari-focalWV-LZA61/2S 
WV-LZA62/2
8x vari-focalWV-LZ62/8S
2 Connect the lens cable to the ALC lens connector of the camera. 
ALC lens connector
1 
3
2 
4
Pin No.  1 Dump 
 2 Dump 
 3 Drive 
 4 Drive 
Important:
 • Follow the installation and connection procedure below to ensure safety. 
						

							14
3 Installation of safety wire
  The following example shows the installation of safety wire:
Important:
 • Be  sure  to  install  safety  wire  between  the  camera  and  the  installation  position  to  prevent  
unexpected injury caused by fallen camera.
 • Ensure that the safety wire is installed. Consult the dealer about installation.
 Attach the safety wire lug (accessory) to the screw hole of the mount 
base with screw (accessory).
1  Loosen one screw in the front portion of the  
camera upper case. (Either left or right)
2  Be sure to attach the safety wire lug (accessory) 
with the wire lug fixing screw (M2.5 × 8 mm) 
provided in the accessories.
Important:
 • Be sure to attach the safety wire lug (accessory) 
with the screw provided in the accessories.   
Using screw of different length may cause 
camera drop or damage.
 • Do not install the safety wire lug at places other 
than the two screw holes of the upper case.
 • Do  not  install  the  safety  wire  lug  on  the 
projections of the upper case. (Install the safety 
wire lug between the two projections)
 • Recommended tightening torque: 0.39 N·m.
Screws of  upper case
Wire engaging holeWire lug fixingscrew (accessory)
Safety wire lug (accessory)
 Engage the safety wire with the wire engaging hole.
1   Pass one end of the safety wire eyelet through the wire engaging hole.
2   Pass the other end of the safety wire through the eyelet.
Safety wire
Wire engaging 
hole 
						

							15
Camera mount
bracket  
(locally procured)
Screws 
(locally procured)
 Screws 
(locally procured)
 

4  Installation of camera mount bracket (locally procured)
Secure the camera mount bracket (locally procured) to the installation position, and mount the 
camera on the camera mount bracket.
Prepare mounting screws according to the material of the area where the camera mount 
bracket (locally procured) is to be installed. The installation method may be different depending 
on the material of the area where the bracket is to be installed.
 • When installing on steel: Fix with bolts and nuts (M6 or M8).
 • When installing on concrete: Fix with expansion anchor bolts (M6 or M8).
 • Use mount bracket with strength 5 times of the total weight of the camera body and lens.
 • The  height  and  length  of  the  camera  mount  bracket  must  be  appropriate  to  ensure  the  use 
of the safety wire in the accessories.
The mounting conditions of the camera mount bracket (locally procured) are described as 
follows:
Installation 
place
Recommended 
screw
Number of screwMinimum pull-out
strength (per 1 pc.)
On ceilingM6 or M83 pcs.196 N
On wallM84 pcs.392 N
Important:
 • Refer  to  the  operating  instructions  of  the  camera  mount  bracket  (locally  procured)  for  the  
mounting angle of the camera mount bracket for a ceiling or wall.
 • When the camera mount bracket is mounted on a wall, be sure to observe the mounting height 
described on the illustration.
More than 
270 cm
Floor
 
						

							16
5   Mount the camera on the camera mount bracket
Follow the instruction of camera mount bracket to mount the camera on the camera mount  
bracket, and aware of the followings:
 • Be  sure  to  install  the  tripod  mount  base  and  safety  wire  before  attaching  the  camera  to  the 
camera mount bracket.
 • Change  the  tripod  mount  base  position  when  attaching  the  camera  to  the  ceiling  mount 
bracket. Observe the following precautions at this time.
   If it is needed to restore the tripod mount base to its original position, also observe the fol-
lowing precautions.
 • When  attaching  an  optional  tripod  mount  base  on  the  top  or  bottom  of  the  camera,  use  the 
removed screws to attach the tripod mount base. Use of longer or shorter screws may cause 
the camera or tripod to fall causing damage. (Recommended tightening torque: 0.39 N·m).
Tripod socket 
hole:1/4-20UNCTripod mount base
Screws
	The indentation 
on the mount  
base should 
point forward.)
 
						

							17
6 Attach safety wire (accessory) to the ceiling or wall.
Attach the safety wire to the foundation or other parts of the building with sufficient strength  
(minimum pull-out strength 196 N).
Prepare screws according to the condition of the attachment position. Use the safety wire 
(accessory), washer (accessory) and spring washer (accessory).

   
Ceiling
Recommended screw M4, 
minimum pull-out strength 
196 N  
Washer (accessory) 
Spring washer (accessory) 
Safety wire (accessory)

Washer 
(accessory)
Recommended 
screw M4, 
minimum 
pull-outstrength 
196 N
Foundation or 
other parts of 
the building with 
sufficient strength
Spring 
washer 
(accessory)
Safety wire
(accessory) 
						

							18
7 Connect the video output.
Important:
 • Be sure to turn off the power of each device before connecting. 
 • Be sure to secure the coaxial cable connectors. 
   Connect a coaxial cable (locally procured) to the video output connector. 
To video input 
Coaxial cable123
220 V-240 V     ~50/60 HzVIDEO OUT
h Connect external devices to the external I/O terminal.
   When connecting an external device, remove 9 mm to 10 mm of the  
outer  jacket  of  the  cable  and  twist  the  cable  core  to  prevent  the 
short circuit first. 
  Specification of cable (wire): 22 AWG - 28 AWG, Single core, twisted
Important:
 • Check whether the stripped part of the wire is not exposed and is fully inserted. 
 • Do  not  connect  2  wires  or  more  directly  to  a  terminal.  When  it  is  necessary  to  connect  2  or 
more wires, use a splitter. 
 • Connect an external device with verifying that the ratings are within the specifications above.  
 • When using the external I/O terminals as the output terminals, ensure they do not cause signal  
collision with external signals.

 1 GND 
 2 ALARM OUT 
  Output specification: Open collector output  
                                    (maximum voltage: 20 V DC)
  Off: Internally pulled up 4 V to 5 V DC
  On: Output voltage 1 V DC or less (maximum drive current: 50 mA)
  Functions: Alarm output
Black-and-white mode switching output 
 3 ALARM IN 
  Input specification: No-voltage make contact input (4 V to 5 V DC, internally pulled up) 
  Off: Open or 4 to 5 V DC 
  On: Make contact with GND (required drive current: 1 mA or more) 
  Functions: Alarm input
VMD permitting input 
Black-and-white mode switching input
Scene file switching input
Strip range
9 mm - 10 mm 
1GND 
2ALARM OUT`(Alarm output terminal) 
3ALARM IN`(Alarm input terminal)123 
						

							19

Safety wire
Camera mount bracket   
(option)
The cable shall be 
tied to the camera 
mount bracket by 
cable tie.
Safety wire
Camera 
mount 
bracket 
(option)
The cable 
shall be tied 
to the camera 
mount bracket 
by cable tie.
j Turn on the power.
   WV-CP600/G, WV-CP620/G
   Use the power cord (accessory) to connect the power supply.
Important:
	 •	 The	included	power	cord	is	the	dedicated	power	cord	of	this	product.	Do	not	use	it	with	other	
devices.
Caution:
	•	The	camera	shall	be	connected	with	cord	set	with	plug.	
Plug for respective country shall be mounted on the 
Power cord by a qualified electrical.
9 Use a cable tie (locally procured) to attach the coaxial cable to the camera  
mount bracket.
Important:
	 •	 The	cable	tie	shall	be	made	of	metallic	or	durable	material	to	be	strong	enough	because	the	
coaxial cable plays the role of camera drop prevention measures in case.
	 •	 When	installing	the	camera	mount	bracket	on	a	wall,	the	installation	height	should	be	as	below	
right image.
220 V-240 V AC,  
50/60 Hz
Power cord (accessory)123
220 V-240 V      ~50/60 HzVIDEO OUT 
						

							20
Important:
 • Check whether the cord core is fully inserted into the  
power cord plug.
    
    24 V AC 12 V DC 
  -   2-N    (GND)
 +   1-L ⊕
 3 Tighten the screw of the power cord plug.
  4 Connect the power cord plug to the power supply  
terminal on the rear side of the camera.
Important:
 • Make sure that the power cord plug is inserted fully into 
the power supply terminal.
Connection of power cord
When connecting the power cord, use connectors that are designed for the power cord, and be care-
ful not to let the power cord fall off. 
In addition, waterproofing work is needed at the joint, e.g., wrapping waterproof tape around the joint. 
Cable length and wire gauge 
24 V AC 
The  recommended  cable  length  and  wire  gauge  are  shown  in  the  table  for  reference.  The  voltage  
supplied to the power terminals of the camera should be within 19.5 V AC and 28 V AC.
Power supply  
(24 V AC 
or 12 V DC)
24V~IN2-N1-L123
12VIN-,VIDEO OUT
  WV-CP604E, WV-CP624E
Important:
 • Use 24 V AC or 12 V DC power supply that is insulated  
from 220 V-240 V AC power.  
 • The  power  supply  is  automatically  switchover  either  24  V  
AC or 12 V DC. No setting is required with this camera. 
 1 Loosen the screw of the power cord plug (accessory). 
 2 Connect the power supply of 24 V AC or 12 V DC to the  
power cord plug. 
   Strip  the  end  of  the  wire  by  3  mm  to  7  mm,  and  twist  
the stripped part of the wire sufficiently to avoid short 
circuit. 
   Specification of power cord (wire): AWG #16 - #24,  
Single core, twisted
3 mm - 7 mm
Power cord  
plug (accessory)