Panasonic Color CCTV Camera Wv Cp310 Installation Guide

							11
Locally procure the screws
Screws are not supplied with this product.
Prepare  the  screws  according  to  the  material, 
structure,  strength  and  other  factors  of  the 
mounting  area  and  the  total  weight  of  objects 
to be mounted.
Screw tightening
 •  The  screws  and  bolts  must  be  tightened 
with  an  appropriate  tightening  torque 
according  to  the  material  and  strength  of 
the installation area.
  •  Do  not  use  an  impact  driver.  Failure  to 
obser ve  this  may  cause  over tightening 
and consequently damage to the screws.
  •  When  a  screw  is  tightened,  make  the 
screw at a right angle to the surface. After 
tightening  the  screws  or  bolts,  perform 
v i s u a l   c h e c k   t o   e n s u r e   t i g h t e n i n g   i s 
enough and there is no backlash.
Power cord (only for WV-CP300‚ 
WV-CP310)
Connect  the  power  cord  securely.  Run  the 
power  cord  so  that  no  load  is  applied  to  the 
cord  when  panning  or  tilting  the  camera. 
(Failure  to  observe  this  may  disconnect  the 
power  cord,  and  accordingly  no  image  is  dis -
played.)
1(29:@87$1@(JOEE





 
						

							12
Major operating controls and their functions
1   AC power input terminal [120 V~ 60 Hz]
   
Connect with the supplied power cord.
2  Video output connector [VIDEO OUT]
   Provides video output to system units.
3   Tripod mount base
  This  is  used  to  install  the  camera  onto  the 
mount bracket (Iocally procured).
4  ALC lens connector
  Connects to ALC lens (4-pin).
5  Back focus adjustment screw
  Adjusts  the  back  focus  distance  and image focal length.
6  Power input terminal [12 V  IN, 24 V~IN]
    
   The power supply of 24 V AC or 12 V DC is 
connected to this terminal.
7   Setup button [SET]
  Press  the  [SET]  button  once  and  the 
"FOCUS  ADJUSTMENT"  screen  will  be 
displayed.
  Hold  down  the  [SET]  button  for  more  than  2 seconds and the setup menu screen will 
be displayed.
•   [LEFT]/[RIGHT]: Press the [RIGHT] or [LEFT]
button to move to the right or left in the 
menu, or change the displayed values.
•   [UP]/[DOWN]: Press the [UP] or [DOWN] 
button to move up or down in the menu.
(The  directions  of  "UP",  "DOWN", 
"LEFT"and  "RIGHT"  are  as  shown  when 
you are directly facing "UP".)
•   [SET]:  Press  this  button  in  the  menu  to 
confirm the selected value or function.
In  addition,  this  button  is  used  to  open 
submenus.
(Side view) (Bottom view)
(Rear view)  

4
5
UP
SET7
2
1
3
120V~60Hz VIDEO OUT6
24V~IN2-N 1-L
12V IN
VIDEO OUT
2
3
(UP)
UP
(DOWN) SET
(LEFT)
(RIGHT)
1(29:@87$1@(JOEE





 
						

							13
Installation and connection
1 Rotate the lens (option) clockwise slowly to mount the lens.
Important:
  •  CS-mount  lens  can  be  used  on  this  camera.  For  use  of  C-mount  lens,  use  the  C-mount 
adaptor (option).
  •  For  prevention  of  damage  to  the  camera  body,  use  a  lens  with  protrusion  of  5.5  mm  or  less 
from the flange surface. 
Protrusion from mount: 
φ20 mm {25/32 inches} or less
Protrusion from ange: 
5.5 mm {7/32 inches} or less
Optional dedicated lens
Lens type Model No.
ALC lens for  
1/3-type CCD cameras 2x vari-focal
WV-LZA61/2S
WV-LZA62/2
8x vari-focal WV-LZ62/8S
2 Connect the lens cable to the ALC lens connector of the camera. 
ALC lens connector
1
3
2
4
Important:
  • 
Follow the installation and connection procedure below to ensure safety.
Pin No.
 
1  Dump 
  2  Dump 
  3  Drive 
  4  Drive 
1(29:@87$1@(JOEE





 
						

							14
3 Installation of safety wire
  The following example shows the installation of safety wire:
Important:
  •  Be sure to install safety wire between the camera and the installation position to prevent unex-
pected injury caused by fallen camera.
  •  Ensure that the safety wire is installed. Consult the dealer about installation.
 Attach the safety wire lug (accessory) to the screw hole of the mount 
base with screw (accessory).
1   Loosen  one  screw  in  the  front  portion  of  the 
camera upper case. (Either left or right)
2    Be sure to attach the safety wire lug (accessory)  
with the wire lug fixing screw (M2.5 × 8 mm  
{5/16 inches}) provided in the accessories.
Important:
  •  Be  sure  to  attach  the  safety  wire  lug  (accessory) 
with the screw provided in the accessories. Using 
screw  of  different  length  may  cause  camera  drop 
or damage.
  • 
Do not install the safety wire lug at places other than 
the two screw holes of the upper case.
 •  Do  not  install  the  safety  wire  lug  on  the  projec -
tions of the upper case. (Install the safety wire lug 
between the two projections)
  •  Recommended tightening torque: 0.39 N·m  
{0.29 lbf·ft}.
Screws of 
upper case Wire engaging hole
Wire lug xing 
screw (accessory)
Safety wire lug 
(accessory)
 Engage the safety wire with the wire engaging hole.
1   Pass one end of the safety wire eyelet through the wire engaging hole.
2    Pass the other end of the safety wire through the eyelet.
Safety wire
Wire engaging
hole
1(29:@87$1@(JOEE





 
						

							15
Camera mount
bracket 
(locally procured)
Screws 
(locally procured)  
Screws 
(locally procured)  


4  Installation of camera mount bracket (locally procured)
Secure the camera mount bracket (locally procured) to the installation position, and mount the 
camera on the camera mount bracket. 
Prepare  mounting  screws  according  to  the  material  of  the  area  where  the  camera  mount 
bracket (locally procured) is to be installed. The installation method may be different depending 
on the material of the area where the bracket is to be installed.
  • When installing on steel: Fix with bolts and nuts (M6 or M8).
  • When installing on concrete: Fix with expansion anchor bolts (M6 or M8).
  • Use mount bracket with strength 5 times of the total weight of the camera body and lens.
  • The  height  and  length  of  the  camera  mount  bracket  must  be  appropriate  to  ensure  the  use 
of the safety wire in the accessories.
The  mounting  conditions  of  the  camera  mount  bracket  (locally  procured)  are  described  as 
follows:
Installation
position Recommended 
screwScrew quantity
Minimum pull-out
strength (per 1 pc.)
On ceiling M6 or M83 pcs.196 N {44.06 lbf}
On wall M84 pcs.921 N {207.05 lbf}
Important:
 •  Refer  to  the  operating  instructions  of  the  camera  mount  bracket  (locally  procured)  for  the 
mounting angle of the camera mount bracket for a ceiling or wall.
  •  When the camera mount bracket is mounted on a wall, be sure to observe the mounting height 
described on the illustration.
Floor
More than
270 cm 
{8.9 feet}
1(29:@87$1@(JOEE





 
						

							16
5   Mount the camera on the camera mount bracket
Follow  the  instruction  of  camera  mount  bracket  to  mount  the  camera  on  the  camera  mount 
bracket, and aware of the followings:
  • Be  sure  to  install  the  tripod  mount  base  and  safety  wire  before  attaching  the  camera  to  the 
camera mount bracket.
  • Change  the  tripod  mount  base  position  when  attaching  the  camera  to  the  ceiling  mount 
bracket. Observe the following precautions at this time.
    If  it  is  needed  to  restore  the  tripod  mount  base  to  its  original  position,  also  observe  the  fol-
lowing precautions.
  • When attaching an optional tripod mount base on the top or bottom of the camera, use the 
removed  screws  to  attach  the  tripod  mount  base.  Use  of  longer  or  shorter  screws  may 
cause  the  camera  or  tripod  to  fall  causing  damage.  (Recommended  tightening  torque:   
0.39 N·m {0.29 lbf·ft}).
Tripod socket 
hole:1/4-20UNC Tripod mount base
Screws
(The indentation 
on the mount 
base should 
point forward.)

1(29:@87$1@(JOEE





 
						

							17
6 Attach safety wire (accessory) to the ceiling or wall.
Attach  the  safety  wire  to  the  foundation  or  other  parts  of  the  building  with  sufficient  strength 
(minimum pull-out strength 196 N {44.06 lbf}).
Prepare  screws  according  to  the  condition  of  the  attachment  position.  Use  the  safety  wire 
(accessory), washer (accessory) and spring washer (accessory).
 
    
Ceiling
Recommended screw M4, 
minimum pull-out strength 
196 N {44.06 lbf} 
Washer (accessory)
Spring washer (accessory)
Safety wire (accessory)
Washer
(accessory)
Recommended 
screw M4, 
minimum 
pull-outstrength 
196 N {44.06 lbf}  
Foundation or 
other parts of 
the building with 
sufcient strength
Spring washer 
(accessory)
Safety wire
(accessory)
1(29:@87$1@(JOEE





 
						

							18
7 Connect the video output
Important:
  •  Be sure to turn off the power of each device before connecting.
  •  Be sure to secure the coaxial cable connectors.
    Connect a coaxial cable (locally procured) to the video output connector. 
To video input 
Coaxial cable
120V~60HzVIDEO OUT
h 
Use a cable tie (locally procured) to attach the coaxial cable to the camera 
mount bracket.
Important:
  •  The  cable  tie  shall  be  made  of  metallic  or  durable  material  to  be  strong  enough  because  the 
coaxial cable plays the role of camera drop prevention measures in case.
Safety wire
Camera mount 
bracket (locally 
procured) The cable shall be 
tied to the camera 
mount bracket by 
cable tie.


Safety wire
Camera 
mount 
bracket 
(locally 
procured) The cable 
shall be tied 
to the camera 
mount bracket 
by cable tie.
1(29:@87$1@(JOEE





 
						

							
19

9 Turn on the power.
    WV-CP300, WV-CP310
    Use the power cord (accessory) to connect the power supply.
Important:
	 •	 The 	 included 	 power 	 cord 	 is 	 the 	 dedicated 	 power 	 cord 	 of 	 this 	 product. 	 Do 	 not 	 use 	 it 	 with 	 other 	
devices.
  WV-CP304, WV-CP314
Important:
	 •	 Use 	 24 	 V 	 AC 	 or 	 12 	 V 	 DC 	 power 	 supply 	 that 	 is 	 insulated 	
from 	 120 	 V 	 AC 	 power. 	
	 •	 The
	 power 	 supply 	 is 	 automatically 	 switchover 	 either 	 24 	 V 	
AC 	 or 	 12 	 V 	 DC. 	 No 	 setting 	 is 	 required 	 with 	 this 	 camera.

24V~IN2-N 1-L
12V

VIDEO OUT
IN

Power supply 
(24 V AC 
or 12 V DC)

120 V AC, 60 Hz Power cord (accessory)
120V~60Hz
VIDEO OU
T

Caution:
	 •	 ONLY	 CONNECT 	 WV-CP304, 	 WV-CP314 	 TO 	 24V 	 AC 	 OR 	
12V 	 DC 	 CLASS 	 2 	 POWER 	 SUPPLY.
  1	 Loosen 	 the 	 screw 	 of 	 the 	 power 	 cord 	 plug 	 (accessory).
  2	 Connect 	 the 	 power 	 supply 	 of 	 24 	 V 	 AC 	 or 	 12 	 V 	 DC 	 to 	 the 	
power 	 cord 	 plug. 
Strip
	 the 	 end 	 of 	 the 	 wire 	 by 	 3 	 mm 	 to 	 7 	 mm, 	 and 	 twist 	 the 	
stripped 	 part 	 of 	 the 	 wire 	 sufficiently 	 to 	 avoid 	 short 	 circuit.
	 	 Specification
	 of 	 power 	 cord 	 (wire): 	 AWG 	 #16 	 - 	 #24, 	
Single 	 core, 	 twisted 	

Important:
	 •	
Check 	 whether 	 the 	 cord 	 core 	 is 	 fully 	 inserted 	 into 	 the 	 power 	
cord
	 plug.
   
   
    24 V AC
  12 V DC
 
 
-     2-N     (GND)
 
+
 
    1-L
 
⊕

 
Power cord 
plug (accessory)

3 mm - 7 mm 
{1/8 to 1/4 inches} 

1(29:@87$1@(JOEE





 
						

							
20

Cable length and wire gauge
24 V AC 
The  recommended  cable  length  and  wire  gauge  are  shown  in  the  table  for  reference.  The  voltage 
supplied to the power terminals of the camera should be within 19.5 V AC\
 and 28 V AC.
The recommended wire size for 24 V AC power cord is shown below:
12 V DC
Calculation of the relation among the cable length, resistance, and power supply.
The voltage supplied to the camera shall be between 10.8 V DC and 16 V D\
C. 
10.8 V DC ≤ V
A - 2 (R x I x L) ≤ 16 V DC 
L
 
:
 
Cable length (m)
R
 
:
 
Resistance of copper wire (
Ω/m) 
V
A  :   DC output voltage of power supply unit
I
  :   DC current consumption (A)
    See specifications. 
Resistance of copper wire [at 20 °C]

Copper wire size (AWG) #24
(0.205 mm2) #22
(0.325 mm2) #20
(0.519 mm2) #18
(0.833 mm2) #16
(1.307 mm2)
Resistance
Ω/m 0.083
0.0520.0330.0200.013

Copper wire 
size (AWG) #24
(0.205 mm2) #22
(0.325 mm2) #20
(0.519 mm2) #18
(0.833 mm2) #16
(1.307 mm2)
Length
 (approx.) (m)
20 304575120
feet 66 100 150250395

 3   Tighten the screw of the power cord plug.
 
4   Connect the power cord plug to the power supply terminal on the rear side of the camera.
Important:
	 •	 Make
	 sure 	 that 	 the 	 power 	 cord 	 plug 	 is 	 inserted 	 fully 	 into 	 the 	 power 	 supply 	 terminal.

1(29:@87$1@(JOEE