Panasonic Color CCTV Camera Wv Cp300 Wv Cp310 Wv Cp314 Wv Cp304 Installation Guide

							21
j Adjust the camera angle by loosening the screw of the camera mount bracket while viewing the video monitor.
    Be sure to loosen the screw of the camera mount bracket when the camera angle is adjusted. 
If the camera angle is changed when the screw is tight, excessive force is applied to the cam-
era mount bracket and camera, and accordingly they may be damaged. Be sure to tighten the 
screw securely after camera angle adjustment.
Adjust the focus.
   To use a fixed-focal lens
    When adjusting the focus with a fixed-focal lens, use the back focus adj\
ustment knob.
   Adjust the focus with the focus assist function
  The  view  angle  and  aperture  can  be  adjusted  according  to  the  distance  of  the  photographic 
subject. Adjust the view angle and focus when adjusting the camera angle\
.
  1 Loosen  the  zoom  lock  knob.  Adjust  the  view  angle 
with  the  zoom  and  focus  ring  according  to  the 
photographic subject.
  2 Tighten the zoom lock knob.
  3 Press the [SET] button.
  
→ The "FOCUS ADJUSTMENT" screen will appear.  
The  focus  assist  function  will  be  activated  to  perform 
the optimum adjustment. 
  4 
When  the  focus  ring  is  positioned  near  the  best  focus 
position, the position will automatically be memorized as the "PEAK HOLD" position (the high-
er the value is, the closer it is to the focus point).
 5 When  the  focus  ring  is  moved,  the  current  focus  position  will  be  indicated  on  "INDICA-
TOR". Adjust the focus position so that the indicator value goes close to the "PEAK HOLD" 
position.
  6 When the indicator value goes to the best focus position, "BEST FOCUS" will be displayed 
in reverse at the lower right corner of the screen.
  7 Press the [SET] button again to close the "FOCUS ADJUSTMENT" menu. (No operation for 
3 minutes also closes the menu.)
 LOW      HIGH
FOCUS ADJUSTMENT..................I
INDICATOR  1135  BEST
PEAK HOLD  1135  FOCUS
1(29:@87$1@(JOEE





 
						

							22
Important:
 •  If  the  view  angle  changes  during  adjustment,  press  the  [SET]  button  to  close  the  "FOCUS 
ADJUSTMENT"  screen  (once  the  view  angle  changes,  the  "PEAK  HOLD"  and  "INDICATOR" 
values will also change), and repeat from step 3  after the view angle is fixed.
  •  When  shooting  in  the  following  place  or  following  subjects,  press  the  [SET]  button  again  to 
close  the  "FOCUS  ADJUSTMENT"  screen.  Adjust  to  the  best  focus  position  while  viewing  the 
image.
    • Frequently moving subject
    • Subject with large illuminance change
    • Subject with low illuminance
    • Too bright or reflective subject
    • Subject through a window
    • Place where the lens easily becomes dirty
    • Subject with less contrast such as white wall
    • Subject with remarkable depth
    • Subject with heavy flicker
    • Subject with horizontally parallel lines such as a shutter
1(29:@87$1@(JOEE





 
						

							
23

Setup menu

Performing each setting item in the setup menu should be completed in advance to use this unit. Perform 
the settings for each item in accordance with the installation conditions and customer requirements.
List of setup menu

Setup itemDescription
CAMERA ID
This  item  specifies  the  camera  title.  The  camera  title  that  indicates  the 
camera location and other information about the camera is created with 
alphanumeric characters and symbol, and then displayed on the screen.
CAMERA Performs the camera operation settings. 
SCENE 1/
SCENE 2 Selects  a  scene  file.  It  is  possible  to  register  and  save  the  settings  as  a 
scene  file  in  case  that  it  is  necessary  to  change  the  settings  such  when 
shooting at night.
ALC/ELC Selects  the  method  of  controlling  the  quantity  of  light  in  accordance  with 
the lens to be used. 
SHUTTER Specifies the electronic shutter speed.
AGC Specifies gain adjustment.
SENS UP Specifies electronic sensitivity enhancement.
WHITE BAL Specifies white balance adjustment.
DNR Selects the level of the digital noise reduction function.  
D&N (IR/ELE) Performs  each  setting  regarding  the  black-and-white  mode  such  as 
switching between color and black-and-white images. 
VMD Performs settings regarding VMD (Video Motion Detection).
SYSTEM Performs  the  settings  regarding  the  camera  system  such  as 
synchronization and privacy zone.
SYNC Specifies the synchronization type.
PRIVACY ZONE Hides undesired portions in the camera shooting area.
STABILIZER Decides whether or not to enable the image stabilizer.
EL-ZOOM Switches the electronic zoom on and off.
UPSIDE-DOWN Flips the camera images vertically or horizontally.
LDC Adjusts  the  Lens  distortion  correction  to  convert  the  image  so  that  it 
matches the square monitor. 
SPECIAL CHROMA GAIN Adjusts the chroma level (color density).
AP GAIN Adjusts the aperture level.
PEDESTAL Adjusts the pedestal (brightness) level. 
HUE Adjusts the chroma phase (hue).
PIX OFF Corrects image defects such as flaws. 
COMMUNICATIONPerforms  the  communication  setting  of  the  system  with  a  receiver  into 
which this unit is integrated.
CAMERA RESET Restores the settings in the setup menu to the default settings.
SER.NO. Displays the serial number of this unit.
LANGUAGE Selects a language to be used in the setup menu. 

1(29:@87$1@(JOEE





 
						

							24
Screenshot 1
Hold down the [SET] button for about 2 seconds 
to call up the top screen of the setup menu.
 
     MODEL   WV-CP310 SERIES
CAMERA ID     OFF
CAMERA   
SYSTEM
SPECIAL
LANGUAGE
 
 END   SETUP DISABLE
Screenshot 2
The  setup  mode  changes  to  "ENABLE",  and 
the setup menu becomes ready to be set.
   
 MODEL   WV-CP310 SERIE S
CAMERA ID     OF F
CAMERA   
SYSTEM
SPECIAL
LANGUAGE
 END   SETUP ENABL E
    
Step 1
Press  the  [UP]  or  [DOWN]  button  to  move  the 
cursor to "END".
Step 2
Press the [RIGHT] button to move the cursor to 
"SETUP",  and  press  the  [SET]  button  to 
change  the  setup  mode  from  "DISABLE"  to 
"ENABLE".
Step 3
Move  the  cursor  to  the  item  to  be  set,  and 
press the [SET] button.  
The operations in the setup menu are performed with the operation buttons after calling up the 
setup menu on the connected video monitor. 
The description below explains how to operate the setup menu basically.
Screenshots of WV-CP310 are shown as an example.
Basic operation
1(29:@87$1@(JOEE





 
						

							
25

Screenshot 3
The  selected  setup  screen  in  the  setup  menu 
appears on the screen.  
 
    **CAMERA SETUP** 
SCENE1
 ALC/ELC    ALC    
 SHUTTER    OFF
 AGC        ON(HIGH)
 SENS UP    OFF
 WHITE BAL  ATW1
 DNR        HIGH
 
D&R(IR)     AUTO1
 VMD        OFF
 RET TOP END

Note:
	 •	 If 	 the 	 top 	 screen 	 of 	 the 	 setup 	 menu 	 is 	
called  up  with  the  operation  buttons 
while  the  camera  is  operated,  the  setup 
mode
	 is 	 always 	 "DISABLE" 	 to 	 prevent 	
operation errors.
	 	 To
	 perform 	 settings 	 in 	 the 	 setup 	 menu, 	
change 	 the 	 setup 	 mode 	 to 	 "ENABLE".
	 •	 The
	 cursor 	 is 	 a 	 reversely 	 highlighted 	 part.

 Step 4
Perform	 the 	 settings 	 for 	 each 	 item.
• 	
Selection of setting item:
Press 	 the 	 [UP] 	 button 	 or 	 [DOWN] 	 button 	 to 	
move 	 the 	 cursor.
• Change of settings:
Press	 the 	 [RIGHT] 	 button 	 or 	 [LEFT] 	 button.
• Display of advanced setup screen:
Press	 the 	 [SET] 	 button 	 when 	 "
"   i s 
attached
	
to
	
the
	
target
	
setting
	
item.
• Return to previous setup screen:
Move 	 the 	 cursor 	 to 	 "RET" 	 and 	 press 	 the 	
[SET]
	 button.
• Return to the top screen:
Move	 the 	 cursor 	 to 	 "TOP" 	 and 	 press 	 the 	
[SET]
	 button, 	 to 	 display 	 the 	 top 	 screen 	 of 	
the setup menu.
Step 5
Move	 the 	 cursor 	 to 	 “END” 	 and 	 press 	 the 	 [SET]
button 	 to 	 return 	 to 	 the 	 camera 	 image 	 screen,
or wait about 5 minutes and the setup menu
will automatically close.

1(29:@87$1@(JOEE





 
						

							
26

Screen transition diagram
CP310
CP310
CP300
Top screen “CAMERA ID” screen
“CAMERA  SETUP” screen
“SYSTEM SETUP” screen
“SPECIAL  SETUP” screen
“LANGUAGE SETUP” screen 

 MODEL   WV-CP310 SERIES
CAMERA ID     OFF
CAMERA   
SYSTEM
SPECIAL
LANGUAGE
 
 END   SETUP DISABLE
   **LANGUAGE SETUP**
LANGUAGE      ENGLISH
 SET
 RET TOP END
     **CAMERA ID**    
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-
*/%$
    SPACE POSI 
    RET TOP END RESET
    ................
    **SYSTEM SETUP** 
SYNC          INT
PRIVACY ZONE  OFF
STABILIZER    OFF
EL-ZOOM       OFF
UPSIDE-DOWN   OFF
   -     +
LDC           I......  
0
 RET TOP END
   **SPECIAL SETUP**
CHROMA GAIN    ...
.I..160
AP GAIN        ...I
... 32
PEDESTAL       .I.
.
... 15
HUE        
   ...I...  0
              -     +
PIX OFF
CAMERA RESET
  PUSH SET
 SER.NO. XXXXXXXX COMMUNICATION COAX
 RET TOP END
    **CAMERA SETUP** 
SCENE1
 ALC/ELC    ALC     
 SHUTTER    OF F
 AGC        ON(HIGH)
 SENS UP    OF F
 WHITE BAL  ATW1
 DNR        HIGH      AUTO1
 VMD
 RET TOP END
D&N(IR)  
OFF

1(29:@87$1@(JOEE





 
						

							
27

Screen transition diagram

CP310
CP310
CP300

Top screen “CAMERA ID” screen
“CAMERA  SETUP” screen
“SYSTEM SETUP” screen
“SPECIAL  SETUP” screen
“LANGUAGE SETUP” screen 

 MODEL   WV-CP300 SERIES
CAMERA ID     OFF
CAMERA   
SYSTEM
SPECIAL
LANGUAGE
 
 END   SETUP DISABLE
   **LANGUAGE SETUP**
LANGUAGE      ENGLISH
 SET
 RET TOP END
     **CAMERA ID**    
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-
*/%$
    SPACE POSI 
    RET TOP END RESET
    ................
    **SYSTEM SETUP** 
SYNC          INT
PRIVACY ZONE  OFF
STABILIZER    OFF
EL-ZOOM       OFF
UPSIDE-DOWN   OFF
   -     +
LDC           I......  
0
 RET TOP END
   **SPECIAL SETUP**
CHROMA GAIN    ...
.I..160
AP GAIN        ...I
... 32
PEDESTAL       .I.
.
... 15
              -     +
PIX OFF
CAMERA RESET
  PUSH SET
 SER.NO. XXXXXXXX COMMUNICATION COAX
 RET TOP END
    **CAMERA SETUP** 
SCENE1
 ALC/ELC    ALC     
 SHUTTER    OF F
 AGC        ON(HIGH)
 SENS UP    OF F
 WHITE BAL  ATW1
 DNR        HIGH      OFF
 VMD
 RET TOP END
D&N(ELE)
OFF
HUE        
   ...I...  0

1(29:@87$1@(JOEE





 
						

							
28

Reference page Cause/solution

Troubleshooting

Before	 asking 	 for 	 repairs, 	 confirm 	 the 	 causes 	 with 	 the 	 following 	 table. 	
Contact
	 your 	 dealer 	 if 	 a 	 problem 	 cannot 	 be 	 solved 	 even 	 after 	 checking 	 and 	 trying 	 the 	 solution 	 in 	 the 	
table or a problem is not described below. 
            Symptom

Blurred	 image
The	 temperature 	 of 	 power 	
cord
	 rises 	 or 	 falls 	 when 	 the 	
power cord is bent or 
stretched
	 during 	 use
Damaged	 power 	 cord 	
sheathing
Heated	 portion 	 of 	 power 	 line 	
consisting
	 of 	 power 	 cord, 	
connector,
	 and 	 power 	 plug 	
during
	 use
No	 image 	 displayed
	•	 Are	 the 	 power 	 cord 	 and 	 coaxial 	 cable 	
connected appropriately?
  
→  Check 	 whether 	 the 	 connection 	 is 	
appropriately established.
19~20
	• Is 	 the 	 monitor 	 brightness 	 appropriately 	
adjusted, or is the contrast appropriately 
adjusted?
   →   Check 	 whether 	 the 	 monitor 	 settings 	
are appropriate.

-

	•	 Is 	 the 	 lens 	 of 	 the 	 camera 	 soiled 	 with 	 dirt 	
or dust?
  
→   Check 	 whether 	 the 	 lens 	 of 	 the 	  
camera is clean.
 
-
	•	 The
	
power
	
cord,
	
power
	
connector,
	
or
	
power
	
plug
	
is
	
damaged.
	
Continuous
	
use
	
of
	
the
	
damaged
	
cord,
	
connector,
	
or
	
plug
	
may
	
cause
	
electric
	
shock
	
or
	
fire.
	 	 Disconnect
	
the
	
power
	
plug
	
immediately
	
and
	
request
	
repair
	
from
	
your
	
dealer.

-
 •	 Is 	 the 	 focus 	 adjusted 	 correctly?
   →   Check 	 if 	 the 	 focus 	 is 	 adjusted 	  
correctly.
21~22
	•	 Is 	 the 	 lens 	 cap 	 detached?  →   Check 	 whether 	 the 	 lens 	 cap 	 is 	 removed. 	
-

1(29:@87$1@(JOEE





 
						

							29
Specifications
WV-CP310WV-CP300WV-CP314WV-CP304
Power source 120 V AC 60 Hz 24 V AC 60 Hz, 12 V DC
Power consumption 1.9 W 24 V AC: 2.3 W, 12 V DC: 210 mA
Image sensor 1/3-type interline transfer CCD
Effective pixels 976 (H) × 494 (V)
Scanning area 4.8 mm (H) × 3.6 mm (V) {3/16 inches (H) × 5/32 inches (V)\
}
Scanning system 2:1 interlace
Scanning line 525 lines
Horizontal scanning frequency 15.734 kHz
Vertical scanning frequency 59.94 Hz
Synchronization Internal (INT), multiplexed vertical drive (VD2)
Horizontal resolution 650 TV lines
Vertical resolution 350 TV lines
Video output 1.0 V [p-p] NTSC composite video signal 75 Ω
Signal-to-noise ratio 52 dB (AGC OFF)
Minimum illumination 0.08 lx (color mode)
0.008 lx 
(black-and- 
white mode)0.05 lx (black-and- 
white mode)0.008 lx(black-and- 
white mode)0.05 lx (black-and- 
white mode)
ALC lens drive DC drive
Lens mount CS-mount
Ambient operating temperature –10 °C to +50 °C {14 °F to 122 °F}
Ambient operating humidity Less than 90 %
Dimensions
101 mm (L) × 72 mm (W) × 55 mm (H)
{3-31/32 inches (L) × 2-27/32 inches 
(W) × 2-5/32 inches (H)}81 mm (L) × 72 mm (W) × 55 mm (H)
{3-3/16  inches (L) × 2-27/32 inches 
(W) × 2-5/32 inches (H)}
Mass Approx.190 g {0.42 lbf}
 (Power cord  excluded) Approx.160 g
{0.35 lbf}
Camera title Chinese: up to 8 characters; English letter, numbers and symbols: 
up to 16 characters.
Light control mode setting  ALC/ALC+/ELC
Back light compensation ON/OFF
Auto black stretchON/OFF
Shutter speed OFF (1/60), 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 
1/10000, 1/120000 (s)
Auto gain control ON (HIGH/MID/LOW), OFF
Sensitivity up OFF/AUTO (×2, ×4, ×6, ×10, ×16, ×32)/FIX (×2, ×\
4, ×6, ×10, ×16, 
×32, ×64, ×128, ×256, ×512)
White balance ATW1/ATW2/AWC
Digital noise reduction LOW/HIGH
Day&Night (IR) AUTO1/AUTO2/ON/OFF 
CP310
CP310
CP300
Day&Night (Electronic)AUTO/OFF 
CP310
CP310
CP300
General 
1(29:@87$1@(JOEE





 
						

							30
CD-ROM* ..................................................................... 1 pc.
Installation Guide (this book)  .........................................1 pc.
Warranty card  ............................................................... 1 pc.
* The CD-ROM contains the operating instructions and installation guide (\
PDF).
The following parts are used during installation procedures:
Power cord (only for WV-CP300 and WV-CP310) 
 (Approx. 1.8 m {5.9 feet})  .......................................1 pc.
Power cord plug   (only for WV-CP304 and WV-CP314)  ......................1 pc.
Safety wire lug  .............................................................. 1 pc.
Safety wire (Approx. 300 mm {1 feet})   ..........................1 pc.
Wire lug fixing screws (M2.5 × 8 mm {5/16 inches})  ......2 pcs. (including 1 for replacement)
Washer........................................................................\
.. 1 pc.
Spring washer  .............................................................. 1 pc.
Standard accessories
WV-CP310WV-CP300WV-CP314WV-CP304
Video motion detection OFF/MOTION DETECTION/SCENE CHANGE
Number of scene file 2
Privacy zone ON (1)/ON (2)/OFF
Image stabilizer ON/OFF
Electronic zoom ON (up to 2x)/OFF
Upside-down ON/OFF
Lens distortion correction 0 to 255
※ Values of weight and dimensions are approximate. The specification is subject to change with- out notice.
1(29:@87$1@(JOEE