Panasonic Color Cctv Camera Wv Cp300 Operating Instructions

							21
→ The "ZONE NUMBER" screen appears. 
Step 2
Move  the  cursor  to  the  number  at  the  right  of  the  title  and  select  the  zone  number  using  the 
right or left button. 
Step 3
Move the cursor to "POSITION" and press the [SET ] button. 
Step 4
Use  the  [UP],  [dOwN],  [RIghT],  and  [lEfT]  buttons  to  determine  the  left  upper  position  of  the 
zone to be set and press the [SET ] button. 
Step 5
Use the [UP], [dOwN], [RIghT], and [lEfT ] buttons to determine the lower right position of the 
zone to be set and press the [SET ] button. 
→ An asterisk "*" will be displayed after the number and the zone setting\
 will be saved. 
Step 6
when “ON (2)” is selected for “PRIVACY ZONE”, the mosaic level may be adjusted. The mosaic 
level may be set through “ZONE lEVEl”. (Range: 1 to 4) 
Note:
  •	 To	 delete	 a	zone,	 select	 the	zone	 number	 and	press	 the	[SET ]	 button	 after	moving	 the	cur-
sor to "dEl". 
	 •	 To	change	the	settings	of	a	zone,	select	the	zone	number	and	repeat	from	step	3.	
B Image stabilizer setting [STABILIZER]
whether or not to enable the image stabilizer is determined. 
This function is effective for the case that the camera is installed at a place with slight\
 shaking. 
ON:  Enables the image stabilizer. 
OFF (default):   disables the image stabilizer. 
Important:
	 •	 When	"ON"	is	selected	 for	the	 image	 stabilizer,	 the	view	 angle	 becomes	 narrower	and	the	
resolution  becomes  lower.  when  "ON"  is  selected  for  the  image  stabilizer,  check  the  view 
angle and resolution at camera installation. 
	 •	 The	image	stabilizer	function	may	not	work	for	the	following	subjects.
	 	 •	Dark	subject	
	 	 •	Less	contrasty	subject	(e.g.	white	wall)	
	 	 •	Subject	shaking	at	excessive	speed		
	 	 •	Large	amplitude
	

image	shaking
C Electronic zoom setting [EL-ZOOM] 
whether or not to use the electronic zoom is determined. 
ON:  Uses the electronic zoom. 
OFF (default):  does not use the electronic zoom.  
						

							22
When "ON" is selected, the zoom factor and the panning/tilting settings \
can be configured. 
Follow the procedure below.
      **EL-ZOOM**
 PUSH SET
      PUSH SET      **EL-ZOOM**
PUSH SET
PUSH SET      **EL-ZOOM**
PUSH SET
PUSH SETZOOM
PAN/TILT ZOOM
PAN/TILT ZOOM
PAN/TILT
 U ZOOM D U ZOOM D
 L PAN R
“SYSTEM SETUP” screen EL-zoom setting screen 
Pan/tilt setting screen
Zoom setting screen
 RET TOP END  RET TOP END RET TOP END
 OFF
    **SYSTEM SETUP** 
SYNC          INT
PRIVACY ZONE
STABILIZER    OFF
EL-ZOOM       ON
UPSIDE-DOWN   OFF
  
-     +
LDC           I......  0
 RET TOP END
Step 1
Move the cursor to "EL-ZOOM", select "ON" and press the [SET ] button. 
→ The "EL-ZOOM" setting screen will be displayed. 
Step 2
Move the cursor to "PUSH SET" of "ZOOM" and press the [SET ] button. 
→ The zoom setting screen appears. 
Step 3
Adjust the angular field of view by changing the electronic zoom factor (up to 2x) using the [UP] 
or [DOWN] button, and press the [SET ] button. 
Note:
	 •	 When	the	zoom	factor is incremented, resolution will be deteriorated. 
Step 4
Move the cursor to "PUSH SET" of "PAN/TILT" and press the [SET ] button. 
→ The pan/tilt setting screen appears. 
Step 5
Use the [UP], [DOWN], [RIGHT], and [LEFT
] buttons to determine the position of the area to be 
set and press the [SET ] button. 
The position can be changed in the range of zoom factor set in the "ZOOM\
" setting screen. 
D	Upside-down	setting	[UPSIDE-DOWN]	
ON:   The video image can be reversed upside down. 
OFF (default):   The video image cannot be reversed upside down.
E Lens distortion correction [LDC]
The image may be distorted depending on the lens used and the zoom factor. By adjusting the 
lens  distortion  correction  setting,  the  distorted  image  can  be  converted  to  match  the  square 
monitor and achieve effects desired by the user. 
Note:
	 •			Depending	on	the	lens	used,	complete	correction	may	not	be	achieved.	 
						

							23
The special menu setup is performed including the setting of the camera image quality and the 
communication  configuration  when  a  decoder  is  used.  The  following  settings  are  to  be  config-
ured  on  the  "SPECIAL  SETUP"  screen  displayed  from  the  top  screen.  Refer  to  page  5-6  for 
how to call up the screen. 
F Chroma level adjustment [CHROMA GAIN] 
Use  the  [RIghT]  or  [LEfT]  button  to  adjust  the  color  density  of  the  camera  image.  When  the 
level indicator moves in the "+" direction, the color becomes thicker, and when the level indica-
tor moves in the "–" direction, the color becomes thinner. Be sure to view a vector chromaticity 
indicator or a monitor when the adjustment is performed. 
G Aperture level adjustment [AP GAIN]
Use the [RIghT] or [LEfT] button to adjust the image quality. When the level indicator moves in 
the  "+"  direction,  the  image  becomes  sharper,  and  when  the  level  indicator  moves  in  the  "–" 
direction,  the  image  becomes  softer.  Be  sure  to  view  a  monitor  when  the  adjustment  is 
performed.
Note:
	 •		Moire 	(interferenc e  fringes)  may  be  observed  when  shooting  a  subject  with  fine  pattern 
such  as  a  carpet  or  a  curtain.  In  such  a  case,  move  the  indicator  in  the  "-"  direction  to 
reduce moire. 
H Pedestal level adjustment [PEDESTAL] 
Use  the  [RIghT ]  or  [LEfT]  button  to  adjust  the  pedestal  level  of  the  camera.  When  the  level 
indicator  moves  in  the  "+"  direction,  the  image  becomes  brighter,  and  when  the  level  indicator 
moves in the "–" direction, the image becomes darker. Be sure to view a waveform monitor or a 
monitor when the adjustment is performed. 
I Chroma phase (hue) adjustment [HUE] 
Use the [RIghT ] or [LEfT] button to adjust the pedestal level of the camera. Be sure to view a 
vector chromaticity indicator or a monitor when the adjustment is performed. 
Special menu setting [SPECIAL SETUP] 
SPECIAL SETUP screen
   **SPECIAL SETUP**
CHROMA GAIN    ...
.I..160
AP GAIN        ...I... 32
...I...  0
PEDESTAL      
HUE       .I.
.
... 15
              -     +
PIX OFF
CAMERA RESET   PUSH SET
 SER.NO. XXXXXXXX COMMUNICATION COAX
 RET TOP END 
						

							24
J	Flaw	compensation	[PIX	OFF]	
Flaws of pixel in the displayed camera image are corrected. Up to 16 points can be corrected. 
Follow the procedure below. 
Step 1
Move the cursor to "PIX OFF" and press the [SET ] button. 
→ The "PIX OFF" screen appears. 
Step 2
Select  a  number  (1  to  16)  with  which  a  pixel  compensation  point  is  registered  and  press  the 
[SET ] button. 
→ The pixel compensation positioning screen appears. 
Step 3
Use the [UP], [DOWN], [RIGHT], and [LEFT] buttons to move the crosshair cursor to the center 
of the flaw to be corrected and press the [SET ] button. 
→    The flaw is corrected and the pixel compensation point is registered. The "PIX OFF" screen 
appears again. An asterisk "*" is attached at the right side of the number when registration 
is completed. The coordinate is expressed in figures. 
Note:
	 •		To 	c lear  the  registered  pixel  compensation  point,  move  the  cursor  to  “1”  of  the  right  of 
“DEL”, use the [RIGHT ] and [LEFT] buttons to select the number with which the target pixel 
compensation point is registered and press the [SET ] button. The registered pixel compen-
sation point is cleared, and an asterisk "*" at the right side of the number disappears. 
K	Communication	setting	[COMMUNICATION]	
The required communication configuration is performed to use this unit integrated into the sys-
tem with a receiver. 
COAX (RCV): Select COAX (RCV) when using our decoder (e.g. WV-RC150). 
COAX (default): Select this setting when not using any receiver.  
						

							25
L Default resetting [CAMERA RESET] 
The settings in the setup menu are restored to the default settings. 
Move  the  cursor  to  "→ PUSH  SET"  of  "CAMERA  RESET"  and  hold  down  the  [SET ]  button  for 
more  than  2  seconds  to  enter  the  next  screen.  To  return  to  the  previous  screen  without  reset-
ting, move the cursor to “NO” and press the [SET ] button. To restore the default settings, move 
the cursor to "YES" and press the [SET ] button. 
Note:
	 •		The	data	of	the	registered pixel compensation points is not cleared.  
	 •		To	 set	whether	 to	reset	 the	camera,	 select	“YES”	 or	“NO”	 by	using	 the	[SET ]	 button.	 To	set	
with a controller, refer to the instruction manual of the controller. 
M	Serial	number	viewing	[SER.NO.]	
Displays the serial number of this product.  
						

							26
The  language  selection  can  be  made  on  the  "LANGUAGE  SETUP"  screen  displayed  from  the 
top screen. Refer to page 5-6 for how to call up the screen.  
Move  the  cursor  to  “LANGUAGE”,  use  the  [RIGHT]  or  [LEFT]  button  to  select  the  target  lan-
guage, then move the cursor to “SET”, and press the [SET ] button. 
Select the target language from the following. 
JAPANESE/ENGLISH (default)/FRANÇAIS/ESPAÑOL/DEUTSCH/ITALIANO/PУCCKИЙ/ 中文
 
Note:
	 •		When	the	camera	language	is	changed,	the	camera	titles	that	have	been	set	will	disappear.	
LANGUAGE SETUP screen 
   **LANGUAGE SETUP**
LANGUAGE      ENGLISH
 SET
 RET TOP END
Camera language selection [LANGUAGE SETUP]  
						

							27
Use of a system controller with the "Camera function" button allows users to perform the 
shortcut settings with use of the numeric keypad and camera function but\
ton. The available 
shortcut operations with this unit are shown as follows. System controller operation  Setting contents
[9]	+	[0]	+	[Camera	function]		 Black-and-white	control	(BW)	ON
[9]	+	[1]	+	[Camera	function]		 Black-and-white	control	(BW)	OFF
[9]	+	[2]	+	[Camera	function]		 Black-and-white	control	(BW)	AUTO	1
   Black-and-white control (BW) AUTO
[9]	+	[3]	+	[Camera	function]		 Camera	title	(CAMERA	ID)	ON
[9]	+	[4]	+	[Camera	function]		 Camera	title	(CAMERA	ID)	OFF
[9]	+	[8]	+	[Camera	function]		 Electronic	zoom	ON
[9]	+	[9]	+	[Camera	function]		 Electronic	zoom	OFF
[1]	+	[6]	+	[8]	+	[Camera	function]		 Black-and-white	control	(BW)	AUTO	2
[1]	+	[6]	+	[9]	+	[Camera	function]		 Iris	of	lens	(IRIS)	OPEN
[1]	+	[7]	+	[0]	+	[Camera	function]		 Iris	of	
lens	(IRIS)	CLOSE
[1]	+	[7]	+	[1]	+	[Camera	function]		 Electronic	shutter	(SHUTTER)	ON
[1]	+	[7]	+	[2]	+	[Camera	function]		 Electronic	shutter	(SHUTTER)	OFF
[1]	+	[7]	+	[3]	+	[Camera	function]		 Electronic	shutter	speed,	1	step	faster
[1]	+	[7]	+	[4]	+	[Camera	function]		 Electronic	shutter	speed,	1	step	slower
[1]	+	[7]	+	[5]	+	[Camera	function]		 Gain	adjustment	(AGC)	ON
[1]	+	[7]	+	[6]	+	[Camera	function]		 Gain	adjustment	(AGC)	OFF
[1]	+	[7]	+	[7]	+	[Camera	function]		 Electronic	sensitivity	up	(SENS	UP)	FIX	ON
[1]	+	[7]	+	[8]	+	[Camera	function]		 Electronic	sensitivity	up	(SENS	UP)	FIX	
OFF
[1]	+	[7]	+	[9]	+	[Camera	function]		 Electronic	sensitivity,	1	step	up	(FIX)	
[1]	+	[8]	+	[0]	+	[Camera	function]		 Electronic	sensitivity,	1	step	down	(FIX)	
[1]	+	[8]	+	[1]	+	[Camera	function]		 Electronic	sensitivity	up	(SENS	UP)	AUTO	ON
[1]	+	[8]	+	[2]	+	[Camera	function]		 Electronic	sensitivity	up	(SENS	UP)	AUTO	OFF
[1]	+	[8]	+	[3]	+	[Camera	function]		 Electronic	sensitivity,	1	step	up	(AUTO)	
[1]	+	[8]	+	[4]	+	[Camera	function]		 Electronic	sensitivity,	1	step	down	(AUTO)
[1]	+	[9]	+	[0]	+	[Camera	function]		 BW	AUTO	switching	time,	2	sec.	
[1]	+	[9]	
+	[1]	+	[Camera	function]		 BW	AUTO	switching	time,	10	sec.
[1]	+	[9]	+	[2]	+	[Camera	function]		 BW	AUTO	switching	time,	30	sec.	
[1]	+	[9]	+	[3]	+	[Camera	function]		 BW	AUTO	switching	time,	60	sec.	
[2]	+	[0]	+	[1]	+	[Camera	function]		 Image	stabilizer	(STABILIZER)	ON	
[2]	+	[0]	+	[2]	+	[Camera	function]		 Image	stabilizer	(STABILIZER)	OFF
[2]	+	[1]	+	[3]	+	[Camera	function]		 Scene	file	1
[2]	+	[1]	+	[4]	+	[Camera	function]		 Scene	file	2
[2]	+	[1]	+	[5]	+	[Camera	function]	 Gain	(AGC),	1	step	up	
[2]	+	[1]	+	[6]	+	[Camera	
function]	 Gain	(AGC),	1	step	down
 
Shortcut operation 
CP310
CP310
CP300
CP310
CP310
CP300
CP310
CP310
CP300
CP310
CP310
CP300
CP310
CP310
CP300 
						

							Panasonic System Communications Company of North America,
Unit of Panasonic Corporation of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Three Panasonic Way, Secaucus, New Jersey 07094 U.S.A.
Panasonic Canada Inc. 
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada 
(905)624-5010
www.panasonic.ca
© Panasonic System Networks Co., Ltd. 2012 
sC0112-0    PGQP1253ZA    Printed in China