Panasonic Color Cctv Camera Wv Cf344 Operating Instructions

							21
C Electronic zoom setting [EL-ZOOM] 
Whether or not to use the electronic zoom is determined. 
ON:  Uses the electronic zoom. 
OFF (default):  Does not use the electronic zoom. 
When "ON" is selected, the zoom factor and the panning/tilting settings \
can be configured. 
Follow the procedure below.
Step 1
Move the cursor to "EL-ZOOM", select "ON" and press the [SET ] button. 
→ The "EL-ZOOM" setting screen will be displayed. 
Step 2
Move the cursor to "PUSH SET" of "ZOOM" and press the [SET ] button. 
→ The zoom setting screen appears. 
Step 3
Adjust  the  angular  field  of  view  by  changing  the  electronic  zoom  factor  (up  to  2x)  using  the 
[UP]/ [DOWN] button, and press the [SET ] button. 
Note:
	 •	 When	the	zoom	factor	is	incremented,	resolution	will	be	deteriorated.	
Step 4
Move the cursor to "PUSH SET" of "PAN/TILT" and press the [SET ] button. 
→ The pan/tilt setting screen appears. 
Step 5
Use the [UP], [DOWN], [RIGHT], and [LEFT ] buttons to determine the position of the area to be 
set and press the [SET ] button. 
The position can be changed in the range of zoom factor set in the "ZOOM\
" setting screen. 
D Upside-down setting [UPSIDE-DOWN] 
ON:   The video image can be reversed upside down. 
OFF (default):   The video image cannot be reversed upside down.
E Lens distortion correction [LDC]
The  image  may  be  distorted  depending  on  the  lens  used  and  the  zoom  factor.  By  adjusting  the  lens  dis-
tortion correction setting, the distorted image can be converted to match the square monitor and achieve 
effects desired by the user. 
      **EL-ZOOM**       **EL-ZOOM**
 PUSH SET      PUSH SET
      **EL-ZOOM**              PUSH SET
              PUSH SETPUSH SET
PUSH SETZOOM
PAN/TILT ZOOM
PAN/TILT ZOOM
PAN/TILT
U ZOOM D      
     L PAN R  
SYSTEM SETUP screen
“EL-ZOOM” setting screen
 RET TOP END  RET TOP END
“ZOOM” setting screen “PAN/TILT” setting screen 
 RET TOP END
MANUAL
SYNC
PRIVACY ZONE
STABILIZER
EL-ZOOM
UPSIDE-DOWN OFF
INT
OFF
ON
OFF I......  0 -     +LDC
FOCUS
 **SYSTEM SETUP** 
 RET TOP END U TILT D
/ 
						

							22
Note:
	 •			Depending	on	the	lens	used,	complete	correction	may	not	be	achieved.	
F Focus setting [FOCUS]  CF354 
Sets the focus adjustment method and fine adjustment method.
Follow the procedure below. 
Important:
	 •	 The	 focus	assist	 function	 is	used	 for	focus	 adjustment	 at	setup.	 This	function	 is	not	 a	func-
tion that is supposed to be operated continuously such as the auto focus\
 function.
	 •	 When	 focus	missing	 occurs	due	to	secular	 change	 in	the	 lens	 and	installation	 environment	
or peripheral temperature change, the focus adjustment is required again. 
Step 1 
Move the cursor to "ABF  PUSH" of "FOCUS" and press the [SET] button. 
 The  focus  function  provides  focus  adjustment  to  automatically  focus  on  a  subject  located  in 
the center of the screen. 
Step 2 
To  fine  adjust  the  focus,  move  the  cursor  to  "MANUAL",  press  the  [SET]  button,  and  use  the 
[RIGHT] or [LEFT] button to adjust the focus manually. 
Important:
	 •	 The	following	are	recommendation	for	focus	setting	in	accordance	with	subjects.	
For such case (subject conditions)Select this (recommendation) 
	 •	 Normal	subject	“ABF”
	 •	 Frequently	moving	subject	Fine  adjustment  with  "MANUAL"  setting  after  "ABF"  or 
"MANUAL". 
	 •	 Subject with large illuminance 
change 
	 •	 Subject	with	low	illuminance	
	 •	 Too	bright	or	reflective	subject	
	 •	 Subject	through	a	window
	 •	 Place	where	the	lens	easily	 becomes dirty
	 •	 Subject	with	less	contrast	such	as	 white wall
	 •	 Subject	with	remarkable	depth
	 •	 Subject	with	heavy	flicker
	 •	 Subject	with	horizontally	parallel	 lines such as a shutter 
						

							23
The special menu setup is performed including the setting of the camera image quality and the 
communication  configuration  when  a  decoder  is  used.  The  following  settings  are  to  be  config-
ured  on  the  "SPECIAL  SETUP"  screen  displayed  from  the  top  screen.  Refer  to  page  5-6  for 
how to call up the screen. 
G Chroma level adjustment [CHROMA GAIN] 
Use  the  [RIghT]  or  [LEfT]  button  to  adjust  the  color  density  of  the  camera  image.  When  the 
level indicator moves in the "+" direction, the color becomes thicker, and when the level indica-
tor moves in the "–" direction, the color becomes thinner. Be sure to view a vector chromaticity 
indicator or a monitor when the adjustment is performed. 
H Aperture level adjustment [AP GAIN]
Use the [RIghT] or [LEfT] button to adjust the image quality. When the level indicator moves in 
the  "+"  direction,  the  image  becomes  sharper,  and  when  the  level  indicator  moves  in  the  "–" 
direction,  the  image  becomes  softer.  Be  sure  to  view  a  monitor  when  the  adjustment  is 
performed.
Note:
	 •		Moire	 (interference	 fringes)	may	be	observed	 when	shooting	 a	subject	 with	fine	pattern	 such	as	
a	carpet	or	a	curtain.	In	such	a	case,	move	the	indicator	in	the	"-"	direction	to	reduce	moire.	
I Pedestal level adjustment [PEDESTAL] 
Use  the  [RIghT ]  or  [LEfT]  button  to  adjust  the  pedestal  level  of  the  camera.  When  the  level 
indicator  moves  in  the  "+"  direction,  the  image  becomes  brighter,  and  when  the  level  indicator 
moves in the "–" direction, the image becomes darker. Be sure to view a waveform monitor or a 
monitor when the adjustment is performed. 
J Chroma phase (hue) adjustment [HUE]  
Use the [RIghT ] or [LEfT] button to adjust the pedestal level of the camera. Be sure to view a 
vector chromaticity indicator or a monitor when the adjustment is performed. 
Special menu setting [SPECIAL SETUP] 
SPECIAL SETUP screen 
 PUSH SET
PIX OFF
CAMERA RESET 
 RET  TOP  END  SER. NO.  XXXXXXXX
    **SPECIAL SETUP** I 160 32
15I
I
CHROMA GAIN
AP GAIN
PEDESTAL
+- 0HUE 
						

							24
K Flaw compensation [PIX OFF] 
Flaws of pixel in the displayed camera image are corrected. Up to 16 points can be corrected. 
Follow the procedure below. 
Step 1
Move the cursor to "PIX OFF" and press the [SET ] button. 
→ The "PIX OFF" screen appears. 
Step 2
Select  a  number  (1  to  16)  with  which  a  pixel  compensation  point  is  registered  and  press  the 
[SET ] button. 
→ The pixel compensation positioning screen appears. 
Step 3
Use  the  [UP],  [DOWN],  [RIGHT],  and  [LEFT]  buttons  to  move  the  crosshair  cursor  to  the  center  of 
the flaw to be corrected and press the [SET ] button. 
→	 	 The 	flaw 	is 	corrected	 and	the 	pixel 	compensation	 point	is 	registered.	 The	"PIX 	OFF" 	screen	
appears	 again.	An	asterisk	 "*"	is	attached	 at	the	 right	 side	of	the	 number	 when	registration	 is	
completed. The coordinate is expressed in figures. 
Note:
	 •		To	 clear	the	registered	 pixel	compensation	 point,	move	the	cursor	 to	“1”	 of	the	 right	 of	"DEL"	
screen,  use  the  [RIGHT ]  and  [LEFT]  buttons  to  select  the  number  with  which  the  target  pixel 
compensation  point  is  registered  and  press  the  [SET ]  button.  The  registered  pixel  compensa-
tion	point	is	cleared,	and	an	asterisk	"*"	at	the	right	side	of	the	number	disappears.	
L Communication setting [COMMUNICATION] 
The required communication configuration is performed to use this unit integrated into the sys-
tem with a receiver. 
COAX (RCV): Select COAX (RCV) when using our decoder (e.g. WV-RC150). 
COAX (default): Select this setting when not using any receiver. 
      **PIX OFF**
  1     2     3     4
  5     6     7     8
  9    10    11    12
 13    14    15    16
1
DEL 000 000
SPECIAL SETUP screen  PIX OFF screen 
Pixel compensation positioning screen 
 RET TOP END RET  TOP  END
    **SPECIAL SETUP** I 160
32
15I
 0I
 PUSH SW
CHROMA GAIN
AP GAIN
PEDESTAL
HUE
PIX OFF
CAMERA RESET  SER.NO. XXXXXXXX
+- 
						

							25
M Default resetting [CAMERA RESET] 
The settings in the setup menu are restored to the default settings. 
Move  the  cursor  to  "→ PUSH  SET"  of  "CAMERA  RESET"  and  hold  down  the  [SET ]  button  for 
more  than  2  seconds  to  enter  the  next  screen.  To  return  to  the  previous  screen  without  reset-
ting, move the cursor to “NO” and press the [SET ] button. To restore the default settings, move 
the cursor to "YES" and press the [SET ] button. 
Note:
	 •		The	data	of	the	registered	pixel	compensation	points	is	not	cleared.		
	 •		To	 set	whether	 to	reset	 the	camera,	 select	“YES”	 or	“NO”	 by	using	 the	[SET ]	 button.	 To	set	
with a controller, refer to the instruction manual of the controller. 
N Serial number viewing [SER.NO.] 
Displays the serial number of this product.  
						

							26
The  language  selection  can  be  made  on  the  "LANGUAGE  SETUP"  screen  displayed  from  the 
top screen. Refer to page 5-6 for how to call up the screen.  
Move  the  cursor  to  “LANGUAGE”,  use  the  [RIGHT]  or  [LEFT]  button  to  select  the  target  lan-
guage, then move the cursor to “SET”, and press the [SET ] button. 
Select the target language from the following. 
JAPANESE/ENGLISH (default)/FRANÇAIS/ESPAÑOL/DEUTSCH/ITALIANO/PУCCKИЙ/ 中文 
Note:
	 •		When	the	camera	language	is	changed,	the	camera	titles	that	have	been	set	will	disappear.	
    **LANGUAGE SETUP** 
  SET
   RET TOP END
LANGUAGE      ENGLISH
LANGUAGE SETUP screen
Camera language selection [LANGUAGE SETUP]  
						

							27
Use of a system controller with the "Camera function" button allows users to perform the short-
cut settings with use of the numeric keypad and “Camera function” button. The available short-
cut operations with this product are shown as follows. System controller operation    Setting contents
[9] + [1] + [Camera function]     Black-and-white control (BW) OFF
[9] + [2] + [Camera function]     Black-and-white control (BW) AUTO
[9] + [3] + [Camera function]     Camera title (CAMERA ID) ON 
[9] + [4] + [Camera function]     Camera title (CAMERA ID) OFF
[9] + [8] + [Camera function]     Electronic zoom ON
[9] + [9] + [Camera function]     Electronic zoom OFF
[1] + [6] + [9] + [Camera function]     Iris of lens (IRIS) OPEN
[1] + [7] + [0] + [Camera function]     Iris of lens (IRIS) CLOSE
[1] + [7] + [1] + [Camera function]     Electronic shutter (SHUTTER) ON
[1] + [7] + [2] + [Camera function]     Electronic shutter (SHUTTER) OFF
[1] + [7] + [3] + [Camera function]     Electronic shutter speed, 1 step faster
[1] + [7] + [4] + [Camera function]     Electronic shutter speed, 1 step slower
[1] + [7] + [5] + [Camera function]     Gain adjustment (AGC) ON
[1] + [7] + [6] + [Camera function]     Gain adjustment (AGC) OFF
[1] + [7] + [7] + [Camera function]     Electronic sensitivity up (SENS UP) FIX ON
[1] + [7] + [8] + [Camera function]     Electronic sensitivity up (SENS UP) FIX OFF
[1] + [7] + [9] + [Camera function]     Electronic sensitivity, 1 step up (FIX) 
[1] + [8] + [0] + [Camera function]     Electronic sensitivity, 1 step down (FIX) 
[1] + [8] + [1] + [Camera function]     Electronic sensitivity up (SENS UP) AUTO ON
[1] + [8] + [2] + [Camera function]     Electronic sensitivity up (SENS UP) AUTO OFF
[1] + [8] + [3] + [Camera function]     Electronic sensitivity, 1 step up (AUTO)
[1] + [8] + [4] + [Camera function]     Electronic sensitivity, 1 step down (AUTO)
[2] + [0] + [1] + [Camera function]     Image stabilizer (STABILIZER) ON 
[2] + [0] + [2] + [Camera function]     Image stabilizer (STABILIZER) OFF 
[2] + [1] + [3] + [Camera function]     Scene file 1
[2] + [1] + [4] + [Camera function]     Scene file 2
[2] + [1] + [5] + [Camera function]     Gain (AGC), 1 step up 
[2] + [1] + [6] + [Camera function]     Gain (AGC), 1 step down
 
Shortcut operation 
						

							Panasonic System Communications Company of North America,
Unit of Panasonic Corporation of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Three Panasonic Way, Secaucus, New Jersey 07094 U.S.A.
Panasonic Canada Inc. 
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada 
(905)624-5010
www.panasonic.ca
© Panasonic System Networks Co., Ltd. 2012 
sC0112-0    PGQP1251ZA    Printed in China