Panasonic Color Cctv Camera Wv Cf344 Operating Instructions

11
2 Light quantity control method selection [ALC/ELC] 
The method of controlling the quantity of light is selected from the following in accordance with the lens to 
be used. 
ALC (default): The iris of the lens is automatically adjusted in accordance with the brightness of a 
subject. Select "ALC" when using an ALC lens. 
ALC+:  Controls  the  quantity  of  light  with  a  combination  of  the  electronic  shutter  and  auto  iris.  This 
selection  is  suitable  at  shooting  a  bright...

12
Note:
	 •	 When	“BLC”	is	set	to	“ON”,	“ABS”	displays	“---”	and	may	not	be	operated.	
Step 4
When	"BLC"	is	set	to	"OFF",	bright	areas	of	an	image	are	masked	to	facilitate	the	visibility	of	dark	areas.	
Move	the	cursor	to	"MASK	SET"	and	press	the	[SET ]	button.
→ The mask setting screen appears. 
Step 5
Use the [UP], [DOWN], [RIGHT], and [LEFT] buttons to move the flashing cursor to the area to be 
masked and press the [SET] button. 
When the selected area is masked, the masked...

13
5 Electronic sensitivity enhancement setting [SENS UP]
Use  of  the  electronic  sensitivity  enhancement  function  increases  the  light  sensitivity  of  the 
CCD,  and  accordingly  the  image  becomes  brighter.  The  magnification  is  unchanged  for  selec-
tion  of  FIX,  and  the  magnification  is  automatically  adjusted  in  accordance  with  the  illuminance 
of  a  photographic  subject  for  selection  of  AUTO.  The  magnification  of  the  electronic  sensitivity 
is selectable from...

14
Step 2
Press  the  [SET ]  button  and  adjust  the  white  balance.  "AWC →  PUSH  SET"  is  reversely 
highlighted  during  adjustment.  When  the  reversely  highlighted  display  is  restored,  the  white 
balance adjustment is completed. 
Step 3
Press  the  [rigHT ]  button  to  select  "AWC".  refer  to  this  page  for  fine  adjustment  of  the  white 
balance. 
Note:
	 •	 The	 adjustment	 of	the	 color	 temperature	 ranges	from	approx.	 2,000	K	to	 10,000	 K.	If	the	 range	
is...

15
Step 4
Move the cursor to "POSiTiON" and press the [SET ] button. 
Step 5
Press the [UP], [dOWN], [rigHT] and [LEFT] buttons to move to the upper-left part of the area 
to be set, and press the [SET ] button. 
Step 6
Press the [UP], [dOWN], [rigHT ] and [LEFT] buttons to move to the lower-right part of the area 
to be set, and press the [SET ] button.
7 Digital noise reduction function setting [DNR]
The digital noise reduction function reduces noise automatically under the condition of low...

16
9 VMD setting [VMD] 
The  VMD  function  allows  the  camera  to  detect  object  motion  and  hindrance  to  the  camera. 
Detection  of  object  motion  or  hindrance  to  the  camera  can  be  announced  by  issuing  an  alarm 
signal. 
Important:
	 •	 The	following	 circumstances	 may	result	 in	detection	 failure	or	false	 detection.	 Use	the	camera	
after adjusting the detection area and sensitivity.  •	Not	enough	difference	in	brightness	between	the	background	and	the	moving	photographic...

17
Step 2
Move the cursor to "MASK SET" and press the [SET ] button. 
→ The “MASK SET” screen appears.
MOTION DET screen “MASK SET” screen 
    **
MOTION DET**(1)
LEVEL 
2S
OFF
DWELL TIME
DISPLAY MODE
ALARM
MASK SET
....I.. 
20              -     +
 RET TOP END
In  the  masked  area,  no  alarm  will  be  issued  even  if  a  moving  object  is  detected.  The  masked 
area is set in the same way as the masked area setting in Light quantity control method selec-
tion. (
 page 11)
Step 3
Hold...

18
Step 6
Move the cursor to “Level”. Use the [RIGHT] or [LEFT] button to adjust the level. 
Repeat step 5 and 6 to adjust to optimal level. 
Step 7
Move the cursor to “DWELL TIME ”. Select the dwell time from the following.
2 S (default)/5 S /10 S /30 S 
Alarm  signal  will  be  issued  once  a  continuously  moving  object  is  detected  within  the  specified 
time. 
Setting of scene change detection 
This  function  detects  a  change  in  the  subject  state  that  occurs  by  covering  the  camera...

19
Camera system setting [SYSTEM SETUP] 
Performs the settings relating to the camera system such as synchronization, and privacy zone. 
The  following  settings  can  be  configured  on  the  "SYSTEM  SETUP"  screen  displayed  from  the 
top screen. Refer to page 5-6 for how to call up the screen. 
SYSTEM SETUP screen
 RET TOP ENDABF  PUSH
SYNC
PRIVACY ZONE
STABILIZER
EL-ZOOM
UPSIDE-DOWN OFF
INT
OFF
OFF
OFF
 I......  0
 -     +  LDC
FOCUS
RET TOP END
 **SYSTEM SETUP** 
@ Synchronization method...

20
Step 1
Move the cursor to "PRIVACY ZONE", select "ON (1)" or "ON (2)", and press the [SET ] button. 
→ The "ZONE NUMBER" screen appears. 
Step 2
Move  the  cursor  to  the  number  at  the  right  of  the  title  and  select  the  zone  number  using  the 
[RIGHT] or [LEFT] button. 
Step 3
Move the cursor to "POSITION" and press the [SET] button. 
Step 4
Use the [up], [down], [right], and [left] buttons to determine the left upper position of the zone to 
be set...