Panasonic Cf 72vcjuzqm Owners Manual

							21
Troubleshooting
Check the cable connection for the AC adaptor.
Check to see if a fully charged battery is properly installed.
Remove the battery pack and disconnect the AC adaptor, then connect them again.
Input your password.  If you have forgotten it, contact Panasonic Technical Support.
 page 19
Press   F9   in the Setup Utility (  “Setup Utility”).   This will restore the Setup
Utility’s settings to their default values (except the password settings).  Then, the Setup
Utility must be run once again for you to input the appropriate operating environment set-
tings.  (The processing speed depends on the application software used, so this operation
may not cause the processing speed to increase.)
You can set the date and time using the following menu.
Windows 2000: [Control Panel] - [Date/Time]
Windows XP: [Control Panel] - [Date, Time, Language, and Regional Options] -
[Date and Time]
  When the computer is connected to a LAN, confirm the date and time of the server.
If you continue to experience problems, the internal battery maintaining the clock may
need to be replaced.  Contact Panasonic Technical Support.
  This computer will not correctly recognize the date and time starting from the year 2100
A.D.
Press    F9    in the Setup Utility (  “Setup Utility”).   This will restore the Setup
Utility's settings to their default values (except the password settings).
Try removing all peripheral devices.
Windows 2000
Click [Local Disk(C:)] in [My Computer] with the right button, select [Properties], then
select [Tools] - [Check Now].
Windows XP
Click [Local Disk(C:)] in [Start] - [My Computer] with the right button, select [Proper-
ties], then select [Tools] - [Check Now].
At start-up, press    F8    to operate the computer in the Safe mode.
Use the Windows password as follows:
Windows 2000
Set the password in [Control Panel] - [Users and Passwords], then add the check mark for
[Prompt for password when computer goes off standby] in [Control Panel] - [Power Op-
tions] - [Advanced].
Windows XP
Select the account to change in [Control Panel] - [User Accounts] and set the password, then
add the check mark for [Prompt for password when computer resumes from standby] in
[Control Panel] - [Performance and Maintenance] - [Power Options] - [Advanced].
Windows 2000
After reinstalling, setup Windows and then set the password again.
Windows XP
If you have created a password reset disk (
 page 12), a message is displayed when you
fail to correctly enter the password. Follow the message’s instructions and set the password
again by using the password reset disk.
If you have not created a password reset disk, after reinstalling, setup Windows and then set
the password again.
The power indicator or bat-
tery indicator is not lit
 is displayed
POST Startup Error(s) is
displayed
Windows startup, or an op-
eration is extremely slow
The date and time are incor-
rect
When the previous item is
not the cause
When resuming from the
standby or hibernation
mode, 
 does not appear
even if a password has been
set in the Setup Utility
The password of the admin-
istrator is forgotten When a problem occurs, refer to this page.  The “Reference Manual” also contains detailed information.  If a problem appears to be
related to a software application, read the software related manual.  If you still cannot troubleshoot the problem, contact Panasonic
Technical Support.
Dealing with Problems (Summary)
 Starting Up 
						

							22
Troubleshooting
No display after powering
on
The power has not been
turned off, but after a cer-
tain period of time, there is
no display
The cursor cannot be con-
trolled
An afterimage appears (e.g.,
green, red, and blue dots
remain on the display) or
there are dots not display-
ing the correct colors
The external display no
longer displays properly
The screen becomes disor-
dered
After the display destination
of the screen is switched
with   Fn   +   F3   , the dis-
play destination returns to
both the internal LCD and
external display upon op-
eration
Dealing with Problems (Summary)
When there is no display to an external display,
• Check your cable connection to the external display.
• Confirm your display is powered on.
• Check the settings for your external display.
Try changing the display by pressing    Fn   +   F3   .
When displaying only through an external display, if the computer is shut down by using
the standby or hibernation function, there will be no display on the LCD unless the exter-
nal display is connected when operations are resumed.  In this case, connect the external
display or press   Fn   +   F3   .
Has the computer been set to the power-saving mode?
To resume operation of your computer from the condition the power of the display is off
(for energy conservation purposes), press any key unrelated to the direct triggering of a
selection, like    Shift   .
To save power, your computer may have automatically entered either the standby or
hibernation mode (
  “Computing on the Road”). Slide the power switch.
Restart the computer by using the keyboard (e.g.,      ).
If an image is displayed for a prolonged period of time, an afterimage may appear.  This
is not a malfunction.  The afterimage will disappear when a different screen is displayed.
High-precision and advanced technologies are necessary in the production of color liquid
crystal displays (color LCDs).  Therefore, if 0.002% or less of the picture elements either
fail to light or remain constantly lit (that is, more than 99.998% of elements are function-
ing properly), no defect is considered to exist.
When an external display not compatible with the power saving mode is used with the
computer, the external display may no longer display properly when the computer enters the
condition the power of the display is off (for energy conservation purposes).  In such cases,
turn off the power to the external display.
Changing the number of colors of the display may affect the screen. Restart the computer.
Windows XP
When using DualView, use the same display colors for the external display as those used
by the LCD.
Under the condition that the [Command Prompt] screen is set to “Full Screen”, the display
destination returns to both the internal LCD and external display if “EXIT” is input and the
[Command Prompt] screen is closed, or “Full Screen” is canceled (e.g.,   Alt   +   Enter   ),
when the display destination of the screen is switched with   Fn   +   F3   .
Press   Fn    +   F3   again.
 Display 
						

							23
Troubleshooting
Windows cannot be shut
down or restarted
 Shutting down
Do not shut down Windows during music playback.
If a USB device is connected, try removing it.
Was an attempt made to shut down (or restart) Windows while the computer was con-
nected to a network drive using a LAN?
With the following procedure, shut down (or restart) Windows after disconnecting the
network drive.
1Windows 2000
Select [My Computer] on the Desktop with the right button of the touch pad and then
select [Disconnect Network Drive].
Windows XP
Select [Start] - [My Computer] and then select [Tools] - [Disconnect Network Drive].
2Select all of the displayed network drives, then select [OK].
Is Acrobat Reader installed?
If Acrobat Reader is not installed, run [c:\util
eader\ar500enu.exe] in [Start] - [Run] to
reinstall the program.  When installing the program, do not change the installation destina-
tion folder.  If the destination folder is changed, the Reference Manual cannot be opened
from the [Start] menu.
 Reference Manual
The Reference Manual is
not displayed
The red indicator lights.
Repeated beeping sound
while the computer is in use.
The red indicator blinks
The orange indicator blinksThe battery level is low.  Save your data and power off your computer.
After connecting the AC adaptor or replacing the battery pack with a fully charged one, turn
your computer on.
The battery pack or recharging function may be defective.  Quickly remove the battery
pack and disconnect the AC adaptor, then connect them again.
If the problem persists, contact Panasonic Technical Support.
Unable to charge because of an improper temperature range. ( page 6)
 Battery Indicator
 Others
Press    Ctrl   +   Alt   +   Del   and turn off the computer.
After shutting down by sliding the power switch for more than four seconds, slide the
power switch to power on and open the application again.
If the program no longer works normally, delete the program using the following menu.
Then reinstall the program.
Windows 2000: [Control Panel] - [Add/Remove Programs]
Windows XP: [Control Panel] - [Add or Remove Programs] Computer hangs
Some applications may not
work properlyWhen switching to a different user with the Fast User Switching function, the following
problems may occur.
• Some applications may not work properly (for example, PDF files may not be printed
properly).
• Key combinations with the Fn key may not work.
• It may not be possible to set the settings of the display.
If any of the above occur, log on with the administrator authority again, not using the Fast
User Switching function, and try the operation once more.
 Fast User Switching functionWindows XP 
						

							24
Troubleshooting
Reinstalling Software
Before Reinstallation
 Preparing

\b		
\f	
\
\b
 
		\
\b

	
 
\b				 !#!#$%		 !&
	\b\b\b(	)*+,\b		
\f	 !#!#$	--,.#/  .+\b
\f	
((
\
&
	-
/\f	(	\b
	\b\
\b&	0\
12*23\b	-
 Important
#	3(\b
-
	\b\b	
,
	4\b(\f	\b\b0	-/\f		\b 
\b	\b\
\f	3(		\
\f	\b
\b\
3	
(\f	-
	
	\f		\b\
\b(	
	,	3	\
(	(\f	$	4	(
\
\f	
	+-
		\f	 
(\
\b\b		
\b\
\f		\b\b(\
	
	3(		
-
Reinstalling
1/\b\f	3(	

\b
	\f	
	\b\f	3
3	
(&	,\b
\f	\b\
\b\f	3(	\b-
25\f	\b\f	3		6	.1	\b	#7/8
(	
,
(	 F2\b
\f	\b\b\f	#	\
(-

\f	(
\f0		\b	,	\b	\f	#(	

-
35	
\b
\f	\b	\b
\f	#	(\b

\f	\b(	 F9-
 \f	\b
3\b3	\
	,		6
	8\b
\f	\b(	
 Enter -
4#		683	\b\b
\
\f	\b(	9\b
  F5 9
 F6\b6	\
8\f	(
\f	\
683	\b-
5#	\f	
		\
)\b\f	\

	-
6	 F10-
 \f	\b
3\b3	\
	,		6
	8\b
\f	\b(	
 Enter -/\f	3(		0,\b
\f	:	\b	
 		3	\b		\b\f
((	-#		6)-
	,		
\f	(\b0	\
\b
\f\b\b	;8-
7 \f			\b
\f			\b
\f	(	\b#	3,
			\f	5\b
12225\b

						

							25
Troubleshooting
10
\b	
\f

\b\f

Y 


\b	
\b


\b	




\f



\b
	
\b\b !
#$!%&(
\b)\
*
11After the reinstallation procedure completes, the follow-
ing message will appear on the display.
Windows XP

\b!*+  	
\b
\

\b

,

\


	)!
\
-\f
	\
\b !*+  	
\b

\b


,

!
\f\

	\f
\b \
!#$!%&

\b!*  	
\b

\b

,
 


	)\
!
-\f
	
\b!* 	
\b

\b

,

!
\f\

	\f
\b \
!#$!%&
Windows 2000
Remove the Product Recovery CD-ROM, then restart the
computer by pressing     Ctrl     +   Alt     +     Del     .
12\b\f
. /\b012 3



 F2
\b\b\b\
02


	

)\b\b0
 


13  F9

\b	
\f

\b\f\

.43
\b\b
 Enter 0 2


\b\
 
\b

	

1\b

\b
-

\b	
*
\b
	

*
#
\b
\b\
\b

NOTE
	

	\b
\b

\b

\b
0
	


\b	
%

\b\b
\b
\f\f\b

)
\b


\b	
\b

\b
)


\b
\


\b\f
)\b\



\b
\b

\f\f\b	
\b0\f\b
\b
\b

	

\b\

\f*
\b\f
.%

\b0\f\b	\b3



\
 
Ctrl 5 
Alt  5 
Del

\b	\f\


\b	\f0
12  0 15
		
\
 F2
\b012 
\f

\b	\f

\b	\f0
12  0
15
		
\b

\b
\b\

NOTE
142
\b
.1-
3
\b\b
.0
#\b6
3\b\
 Enter

\b	
\f

\b\f\

.43
\b
 Enter 
15\b\f		
\b\b\b\
\f\b
16 	\f	
\b)	
\b

\b
\b\b\
\b
!	0\f\b
\b
\b
	

\b

\f\
*
Windows 2000 

Windows XP

17!\b02

\

\b 
\b
\b\
\b


$\b
\b
\b
)	


\f
\b
\f



\b
\b
\b
\b-#$
\b#$
\b
\b-\b\f)
\b7\b
\b\b.%83
	\f
9\f

\b\b
\b
	
:

\
.%83
\f
\





\b
\b\

\b\b-#$\
#\b	
\f
\
 #$
)\b
\b\

)\b
\b
	#$

\b\b

\b.%83
CAUTION 
						

							26
Appendix
YOU MAY NOT REVERSE ASSEMBLE, REVERSE COMPILE, OR MECHANICALLY OR ELECTRONICALLY TRACE
THE PROGRAMS, OR ANY COPY THEREOF,  IN WHOLE OR IN PART.
YOU MAY NOT USE, COPY, MODIFY, ALTER, OR TRANSFER THE PROGRAMS OR ANY COPY THEREOF, IN
WHOLE OR IN PART, EXCEPT AS EXPRESSLY PROVIDED IN THE LICENSE.
IF YOU TRANSFER POSSESSION OF ANY COPY OF ANY PROGRAM TO  ANOTHER PARTY, EXCEPT AS PERMIT-
TED IN PARAGRAPH E ABOVE, YOUR LICENSE IS AUTOMATICALLY TERMINATED.
This license is effective only for so long as you own or lease the Product, unless earlier ter minated. You may terminate
this license at any time by destroying, at your expense, the Programs and related documentation together with all
copies thereof in any form. This license will also terminate effective immediately upon occurrence of the conditions
therefore set forth elsewhere in this Agreement, or if you fail to comply with any term or condition contained herein.
Upon any such termination, you agree to destroy, at your expense, the Programs and related documentation together
with all copies thereof in any form. A. MEI hereby grants you a personal, non-transferable and non-exclusive right and license to use the Programs in
accordance with the terms and conditions stated in this Agreement. You acknowledge that you are receiving only
a LIMITED LICENSE TO USE  the Programs and related documentation and that you shall obtain no title,
ownership nor any other rights in or to the Programs and related documentation nor in or to the algorithms,
concepts, designs and ideas represented by or incorporated in the Programs and related documentation, all of
which title, ownership and rights shall remain with MEI or its suppliers.
B. You may use the Programs only on the single Product which was accompanied by the Programs.
C. You and your employees and agents are required to protect the confidentiality of the Programs. You may not
distribute or otherwise make the Programs or related documentation available to any third par ty, by time-sharing
or otherwise, without the prior written consent of MEI.
D. You may not copy or reproduce, or permit to be copied or  reproduced, the Programs or related documentation
for any purpose, except that you may make one (1) copy of the Programs for backup pur poses only in support of
your use of the Programs on the single Product which was accompanied by the Programs. You shall not modify,
or attempt to modify, the Programs.
E. You may transfer the Programs and license them to another party only in connection with your transfer of the
single Product which was accompanied by the Programs to such other par ty. At the time of such a transfer, you
must also transfer all copies, whether in printed or machine readable form, of every Program, and the related
documentation, to the same party or destroy any such copies not so transferred.
F. You may not remove any copyright, trademark or other notice or product identification from the Programs and
you must reproduce and include any such notice or product identification on any copy of any Program.LICENSE
TERM
YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT AND AGREE TO BE BOUND
BY ITS TERMS AND CONDITIONS. YOU FURTHER AGREE THAT IT IS THE COMPLETE AND EXCLUSIVE STATE-
MENT OF THE AGREEMENT BETWEEN US, WHICH SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT,
ORAL OR WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN US, RELATING TO THE SUBJECT MAT-
TER OF THIS AGREEMENT. THE SOFTWARE PROGRAM(S) (“PROGRAMS”) FURNISHED WITH THIS PANASONIC
® PRODUCT (“PRODUCT”)
ARE LICENSED ONLY TO THE END-USER (“YOU”), AND MAY BE USED BY YOU ONLY IN ACCORDANCE WITH
THE LICENSE TERMS DESCRIBED BELOW. YOUR USE OF THE PROGRAMS SHALL BE CONCLUSIVELY DEEMED
TO CONSTITUTE YOUR ACCEPTANCE OF THE TERMS  OF THIS LICENSE.
Matsushita Electr ic Industrial Co., Ltd. (“MEI”) has developed or otherwise obtained the Programs and hereby licenses
their use to you. You assume sole responsibility for the selection of the Product (including the associated Programs) to
achieve your intended results, and for the installation, use and results obtained therefrom.
LIMITED USE LICENSE AGREEMENT 
						

							27
Appendix
A. MEI vous octroie par les présentes le droit et la licence personnels, non cessibles et non exclusifs d’utiliser les
Logiciels conformément aux termes, clauses et conditions de ce Contrat. Vous reconnaissez ne recevoir qu’un
droit limité d’utiliser les Logiciels et la documentation les accompagnant et vous vous engagez à n’obtenir aucun
droit de titre, propriété ni aucun autre droit vis-à-vis des Logiciels et de la documentation les accompagnant ni
vis-à-vis des algorithmes, concepts, dessins, configurations et idées représentés par ou incorporés dans les
Logiciels et la documentation les accompagnant, dont les titres, propriété et droits resteront tous à MEI ou à
leurs propriétaires.
B. Vous ne pouvez utiliser les Logiciels que sur le Produit unique qui est accompagné par les Logiciels.
C. Vous et vos employés ou agents êtes requis de protéger la confidentialité des Logiciels. Vous ne pouvez ni
distribuer ni mettre les Logiciels et la documentation les accompagnant à la disposition d’un tiers, par partage
de temps ou de quelque autre manière que ce soit, sans l’autorisation écrite préalable de MEI.
D. Vous ne pouvez ni copier ni reproduire ni permettre la copie ni la reproduction des Logiciels ni de la documen-
tation les accompagnant pour quelque fin que ce soit, à l’exception d’une (1) copie des Logiciels à des fins de
sauvegarde uniquement pour soutenir votre utilisation des Logiciels sur le Produit unique qui est accompagné
par les Logiciels. Vous ne pouvez ni modifier ni tenter de modifier les Logiciels.
E. Vous ne pouvez céder les Logiciels et en octroyer la licence à une autre par tie qu’en rapport avec votre cession
du Produit unique qui est accompagné par les Logiciels à cette autre partie. Au moment de cette cession, vous
devez céder également toutes les copies, que ce soit sous forme impr imée ou lisible par la machine, de tous les
Logiciels ainsi que de la documentation les accompagnant, à la même par tie ou détruire les copies non cédées.
F. Vous ne pouvez retirer aucune marque de droits d’auteur, marque ou autre ni aucune identification de produit
des Logiciels et vous devez reproduire et inclure toutes ces notices ou identifications de produit sur toutes les
copies des Logiciels.
Vous ne pouvez assembler en sens inverse, compiler en sens inverse ni retracer les Logiciels ni aucune de leurs
copies, de façon électronique ou mécanique, en tout ou en partie.
Vous ne pouvez utiliser, copier, modifier, altérer ni céder les Logiciels ni aucune de leurs copies, en tout ou en partie,
à l’exception de ce qui est expressément stipulé dans ce contrat.
Si vous cédez la possession de toute copie ou de tout Logiciel à une autre partie, à l’exception de ce qui est autorisé
au paragraphe E ci-dessus, votre licence est automatiquement résiliée.Licence
Termes, clauses et conditions
Cette licence n’est effective que pour la durée de possession ou de crédit-bail du Produit, à moins d’une résiliation
antér ieure. Vous pouvez résilier cette licence à tout moment en détruisant, à vos frais, les Logiciels et la documentation
les accompagnant avec toutes leurs copies, sous quelque forme que ce soit. Cette licence sera également résiliée,
avec application immédiate, si les conditions de résiliation définies ailleurs dans ce contrat se sont réalisées ou si vous
ne respectez pas les termes, clauses et conditions qui y sont contenues. Au moment de la résiliation, vous acceptez de
détr uire, à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous quelque forme
que ce soit.
Vous reconnaissez avoir lu ce contrat, en avoir compris toute la substance et avoir accepté de respecter ses termes,
clauses et conditions. Vous reconnaissez en outre qu’ils sont la description complète et exclusive du contrat conclu
entre nous, contrat qui remplace et annule toute proposition ou contrat précédent, écrit ou oral, et toute autre commu-
nication entre nous, relativement à l’objet du présent contrat. Le(s) logiciel(s) (les “Logiciels”) fournis avec ce produit Panasonic
® (le “Produit”) sont exclusivement concédés en
licence à l’utilisateur ultime (“vous”), et ils ne peuvent être utilisés que conformément aux clauses contractuelles ci-
dessous. En utilisant les logiciels, vous vous engagez de manière définitive à respecter les termes, clauses et condi-
tions des présentes.
Matsushita Electr ic Industrial Co., Ltd. (“MEI”) a mis au point ou obtenu les Logiciels et vous en concède l’utilisation par
les présentes. Vous assumez l’entière responsabilité du choix de ce Produit (y compris des Logiciels associés) pour
obtenir les résultats escomptés, ainsi que de l’installation, de l’utilisation et des résultats obtenus.
Contrat de licence d’usage limité 
						

							28
Appendix
Names and Functions of Parts
(  “LED Indicators”)
Before using the computer for
the first time, carefully read the
[Limited Use License Agree-
ment].  If you agree to the con-
ditions, remove the seal.
Security Lock
To adjust the volume*:
Windows 2000
Select the 
 on the taskbar, then [Volume Control].
Windows XP
Select the 
 on the taskbar.
*You may also use the function keys to perform this operation
(  Fn   +   F5   or   F6   ).
Speaker on/off :   Fn   +   F4
Speakers
( page 17)
Use this connector to connect headphones or ampli-
fier-equipped speakers.  Audio output from the in-
ternal speaker is disabled when headphones or ex-
ternal speakers are connected.
Headphone Jack
Microphone Jack
Use only a monaural condenser microphone.
Using an input source other than a monaural con-
denser microphone may not allow audio to be input
or may damage the equipment.
The illustrations shown may differ from the actual physical appearances.
(  “PC Cards”)
PC Card Slots(
  “Modem”)
Multimedia Pocket
(  “Multimedia Pocket” and “CD Drive”)
Carrying Handle
(  “Multimedia Pocket”)
Multimedia Pocket Release Latch
For enhanced portability and
in-the-field efficiency.
LED Indicators A cable can be connected to prevent
theft of your computer.  For more
information, read the manual that
comes with the cable.
LOCK
(  “LED Indicators”)
Power Switch
Caps Lock
Numeric key (NumLk)
Scroll lock (ScrLk)
Hard disk drive status
Multimedia pocket device status
Power status of the multimedia pocket
Main battery pack status
Power statusMP
MP
RELEASE 
 
Modem
LED Indicators
LCD
Function Keys
Touch Pad (
  “Key Combinations”) (Only for models with touchscreen:
  “Touchscreen”) 
						

							29
Appendix
External Display Port
Parallel Port
(
  “Printer”)
DC-IN Jack
USB Por ts
(
  “USB Devices”)These holes allow heat to exit.CAUTION
Do not block or place the computer in a
location that may prevent proper ventila-
tion.
Serial Por t
Ventilation Hole
RAM Module Slot
(
  “RAM Module”)
(  “Port Replicator”)
Expansion Bus Connector (
  “External Display”)
(  “Battery Power”)
Battery Pack
Infrared Communication Por t
External Keyboard/Mouse Port
LAN
(
  “LAN”)
A lithium ion battery that is recyclable powers the product you
have purchased.  Please call 1-800-8-BATTERY for information
on how to recycle this battery.
L’appareil que vous vous êtes procuré est alimenté par une batterie
au lithium-ion. Pour des renseignements sur le recyclage de la
batterie, veuillez composer le 1-800-8-BATTERY. 
						

							30
Appendix
Model No.
CPU
Memory (Expandable to)
Video Memory
LCD Type
Displayed Colors*1
External Display
Hard Disk Drive
Keyboard
Floppy Disk Drive
DVD-ROM Drive
Slots PC Card Slots
Allowable current
(total for two slots)
RAM Module Slot*4
Interface Parallel Por t
External Display Por t
Serial Port
Microphone Jack*5
Headphone Jack
Infrared Communication  Port
External Keyboard/Mouse Port
Expansion Bus Connector
USB Port
Modem
LAN
Pointing Device
Speaker
Sound
Battery Pack
Operating Time*6
Charging Time*6
Clock Batter y
AC Adaptor*7Input
Output
Power Consumption*8
Specifications
Specifications
Main Specifications
CF-72VCJUZQM CF-72V3JUZQM
Mobile Pentium® 4 Processor-M 1.6 GHz featuring Intel® SpeedStepTM technology
L2 (Second) Cache Memor y: 512 KB
256 MB (768 MB Max.)
32 MB
13.3 type (TFT) with Touchscreen 13.3 type (TFT)
256/65536/16M colors (640 x 480 dots/800 x 600 dots/1024 x 768 dots)
256/65536/16M colors (640 x 480 dots/800 x 600 dots/1024 x 768 dots/1280 x
1024 dots/1600 x 1200 dots/2048 x 1536 dots)*2
30 GB*3
87 keys
720 KB/1.44 MB (two-mode)
DVD-ROM: 8x speed (Max.)
CD-ROM: 24x speed (Max.)
Two Type I or Type II, or one Type III
3.3 V: 400 mA
5 V: 400 mA
200-pin, SO-DIMM, DDR-SDRAM, PC2100 Compliant
Dsub 25-pin female
Mini Dsub 15-pin female
Dsub 9-pin male
Miniature jack, 3.5 DIA
Miniature jack, 3.5 DIA
Impedance 32 Ω, Output Power 4 mW x 2
IrDA 1.1 compliant
Mini DIN 6-pin female
Dedicated 100-pin female
4-pin x 2
RJ-11 jack Data: 56 kbps (V.90 & K56flex)   FAX:14.4 kbps
RJ-45 jack IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX
Touch Pad
Speaker (built in)  x 4
WAVE and MIDI playback
Li-ion 11.1 V, 5.4 Ah
Main batter y: Approx. 1 hours - 2.5 hours
Main batter y + Second battery: Approx. 2 hours - 5 hours
Main batter y: Approx. 3 hours
Main batter y + Second battery: Approx. 6 hours
Coin type lithium batter y 3.0 V
100 V - 240 V AC, 50 Hz/60 Hz
15.6 V DC, 5.0 A
Approx. 65 W*9 / Approx. 90 W (maximum when recharging in the ON state)
Battery
Pa c k
*1A 16M color display is achieved by using the dithering function.    Windows XP  : A 256 color and 640x480 dots are not supported.
*2Maximum resolution depends on the specifications of the external display.    Windows XP    : A 256 color and 640x480 dots are not supported.
*31GB = 109 bytes
*4Only a RAM card designed for PC2100 can be added.
*5Use only a monaural condenser microphone.
*6Varies depending on the usage conditions, CPU speed, etc.
*7The AC adaptor is compatible with power sources up to 240 V AC adaptor.
This computer is supplied with a 125 V AC compatible AC cord.
*
8Approx. 0.9 W when the battery pack is fully charged (or not being charged) and the computer is off.
Approx. 1.5 W when the [Wake up from LAN] has been enabled.
*
9Rated power consumption.
Touch Pad, Touchscreen (Anti-Reflection,
Stylus (included) touch capable)